|
sticky
First draft of overall DVSwitch documentation. 2 messages
We have created the first overall document covering all of the new DVSwitch programs. This started as an outline and grew. It is in Google Docs so that people always have access to the latest and grea
We have created the first overall document covering all of the new DVSwitch programs. This started as an outline and grew. It is in Google Docs so that people always have access to the latest and greatest. We are putting the first howto together for a simple bridge and will expand after that. Neither Mike or I are document writers so please bare with us. DVSwitch Documentation 73, Steve N4IRS
By Steve N4IRS
·
|
|
locked
sticky
Improper signals sent to digital networks.
I have noticed a SHARP increase in reports of ASL <-> digital bridges sending unwanted audio to the digital networks. What do I mean by unwanted audio? You should not send any telemetry tones or CW ID
I have noticed a SHARP increase in reports of ASL <-> digital bridges sending unwanted audio to the digital networks. What do I mean by unwanted audio? You should not send any telemetry tones or CW IDs from ASL to a digital network! You should not send any voice telemetry (Allison) to a digital network! You should not bridge to a digital network where a bridge in not allowed. I mean by this, bridging ASL to a busy TG on BrandMeister without permission. Bridging ASL to the NA p25 reflector. You SHOULD respond to network operators requesting that you stop bridging quickly. I have made most of the above mistakes during testing. As soon as I found out it was happening, I pulled the plug and fixed my issue. I contacted the network operators to apologize. This is happening on DMR and P25, This is the quickest way I know to give ASL and DVSwitch a black eye. In the case of P25, it can give the whole MMDVM P25 network a black eye with the Quantar people considering adding repeaters to the reflectors. THINK before you connect. Understand the digital network you are connecting to. How well would it go over if you connected a world wide DMR TG to any of the big ASL hubs? Steve N4IRS
By Steve N4IRS
·
|
|
sticky
First draft of ASL <-> DMR how to document 42 messages
We have added the first howto for bridging AllStarLink to DMR. This is a work in progress so comments are welcome. ASL to DMR Bridge how-to
We have added the first howto for bridging AllStarLink to DMR. This is a work in progress so comments are welcome. ASL to DMR Bridge how-to
By Steve N4IRS
·
|
|
Events Management 16 messages
I have the following event working: PRIMARYHUBUP = v|e|${RPT_ALINKS} =~ "\",50210.\\ but would like to replace 50210 with a variable, $PRIMARYHUB. How do I declare that variable in rpt.conf? Al, K2WM
I have the following event working: PRIMARYHUBUP = v|e|${RPT_ALINKS} =~ "\",50210.\\ but would like to replace 50210 with a variable, $PRIMARYHUB. How do I declare that variable in rpt.conf? Al, K2WM
|
By Al Williams, K2WM
·
|
|
ASL to YSF Question 2 messages
Hey There, I was able to do a ASL to DMR setup with a node on the cloud. Connections are successful and audio is awesome. I would like to go ahead and do a ASL to YSF connection using the same method
Hey There, I was able to do a ASL to DMR setup with a node on the cloud. Connections are successful and audio is awesome. I would like to go ahead and do a ASL to YSF connection using the same method
|
By Tito Lopez
·
|
|
No crontab for root 3 messages
Hi all Got the dv switch software going running ASL& why am I getting accessing my CRON "No crontab for root" The time is messed up too.I do have root privileges Thanks Pete KD2ARB
Hi all Got the dv switch software going running ASL& why am I getting accessing my CRON "No crontab for root" The time is messed up too.I do have root privileges Thanks Pete KD2ARB
|
By Pete Fierro
·
|
|
Failed Kernal 11 messages
Not sure I'm in the right group for this but I'll ask.. Recently tried installing the Allstarlink iso from, https://github.com/AllStarLink/Asterisk/releases/download/ASL-1.01/ASL_1.01-20180417-amd64-i
Not sure I'm in the right group for this but I'll ask.. Recently tried installing the Allstarlink iso from, https://github.com/AllStarLink/Asterisk/releases/download/ASL-1.01/ASL_1.01-20180417-amd64-i
|
By Rick,N1RCW
·
|
|
systemctl on Arch linux HAMVOIP image not working 26 messages
even if I am in the same directory as the file and try to enable and start it systemctl says file not found. please help I would like to get the bridge working. I have tried all the files and this is
even if I am in the same directory as the file and try to enable and start it systemctl says file not found. please help I would like to get the bridge working. I have tried all the files and this is
|
By Brad NK8J
·
|
|
Raspberry Pi ASL install 17 messages
And I'm stumped.... I'm trying to load ASL to a Raspberry Pi 3B. I load raspbian to an SD Card and then use the following: cd /tmp wget http://dvswitch.org/install-allstarlink-repository chmod +x inst
And I'm stumped.... I'm trying to load ASL to a Raspberry Pi 3B. I load raspbian to an SD Card and then use the following: cd /tmp wget http://dvswitch.org/install-allstarlink-repository chmod +x inst
|
By Jeff Lehman, N8ACL
·
|
|
found frequency Segmentation fault with ASL Echolink connect 3 messages
Dear All i run ASL on raspberry pi 3b+ and found ASL asterisk random crash. after try to run via command line i found log as below 1999 are connect to DMR, not problem at all after connect 1998 EchoLi
Dear All i run ASL on raspberry pi 3b+ and found ASL asterisk random crash. after try to run via command line i found log as below 1999 are connect to DMR, not problem at all after connect 1998 EchoLi
|
By E25ECY
·
|
|
DMR -->Allstar 5 messages
Question, is there a setting to send a key-up or un-key tone when a signal is received from the DMR side to Allstar ?? Iam entertaining the thought of a audible "TONE" (courtesy tone) that will sound
Question, is there a setting to send a key-up or un-key tone when a signal is received from the DMR side to Allstar ?? Iam entertaining the thought of a audible "TONE" (courtesy tone) that will sound
|
By Jeff Wood
·
|
|
Allmon2 6 messages
I installed allmon2 on a server running ASL.. The bubble chart does not show.. How can this be fixed?
I installed allmon2 on a server running ASL.. The bubble chart does not show.. How can this be fixed?
|
By Ke4tlc
·
|
|
Sound FOB USB 2 messages
Got a quick question that I cant seem to find the answer to, so I thought Id try here. Could someone instead of routing the signals from the sound FOB to the Pi using the USB to USB connection, Could
Got a quick question that I cant seem to find the answer to, so I thought Id try here. Could someone instead of routing the signals from the sound FOB to the Pi using the USB to USB connection, Could
|
By rmeinke@...
·
|
|
I need some help please setting up a dmr bridge 3 messages
I need help setting up a dmr bridge with a mmdvm hotspot I want it to also go out to echolink can some one pleases help me with this email is n9tcq@... name is Dave phone number is 708 205 3076 I have
I need help setting up a dmr bridge with a mmdvm hotspot I want it to also go out to echolink can some one pleases help me with this email is n9tcq@... name is Dave phone number is 708 205 3076 I have
|
By
David Jansen
·
|
|
ASL on the BBB 6 messages
I am testing the apt-get update / apt-get upgrade and the resize to fill the card now. Steve N4IRS
I am testing the apt-get update / apt-get upgrade and the resize to fill the card now. Steve N4IRS
|
By Steve N4IRS
·
|
|
login and password for hamvoip alarmpi 2 messages
It should be root and root
It should be root and root
|
By Jeff Wood
·
|
|
DVSwitch 8 messages
I have had DVSwitch --> DMR running on Allstar for a long while now...All has been working great, I was using the system last night... woke up this morning with no DMR connection to the Allstar System
I have had DVSwitch --> DMR running on Allstar for a long while now...All has been working great, I was using the system last night... woke up this morning with no DMR connection to the Allstar System
|
By Jeff Wood
·
|
|
Problem with bridge goint thru talk group 6 messages
This is the problem i am having hopefully you can help. I am using Allstar to DMR bridge on my system. I have it configured properly. the thing that is happening it that I can see myself log in when i
This is the problem i am having hopefully you can help. I am using Allstar to DMR bridge on my system. I have it configured properly. the thing that is happening it that I can see myself log in when i
|
By Brad N8PC
·
|
|
allstarlink manual install problem 2 messages
This should go to the AllStarLink message list. Sent via smoke signal (AT&T) ________________________________ Sent: Wednesday, August 21, 2019 10:38:26 AM To: allstarlink@DVSwitch.groups.io <allstarli
This should go to the AllStarLink message list. Sent via smoke signal (AT&T) ________________________________ Sent: Wednesday, August 21, 2019 10:38:26 AM To: allstarlink@DVSwitch.groups.io <allstarli
|
By Ted Holdahl
·
|
|
ASL <-> DMR - no audio 18 messages
I followed the ASL to DMR doc on google drive and everything appeared to work as it does in the doc except when I send the 1000 Hz tone, it's never heard on the DMR radio. The IDer has gone off a coup
I followed the ASL to DMR doc on google drive and everything appeared to work as it does in the doc except when I send the 1000 Hz tone, it's never heard on the DMR radio. The IDer has gone off a coup
|
By Vince Vielhaber
·
|