Re: C Bridge to P25 Reflector

Michael KD5DFB

Okay, making progress! I am stumped on the last piece. 

I am trying to figure out the connection between ipsc_bridge and hb_bridge. 

On ipsc_bridge, I have the dmrlink.cfg connecting to the cbridge and can see traffic from the cbridge in the log. Does the ipsc_bridge.cfg connect to hb_bridge.cfg? 

On the hb_bridge I am a little confused. Does the hb_bridge.cfg connect to analog_bridge? Does the ambe need to match what is in analog_bridge?


On Mon, Jul 16, 2018, 21:02 Steve N4IRS <szingman@...> wrote:
I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?

I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:



[P25 Network]

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge

On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 

# IPSC_Bridge configuration file #


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


gateway = # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)

On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB

Join to automatically receive all group messages.