I reloaded everything to default. I am getting this
now. Which is a good sign.
M: 2021-01-19 02:12:26.829 D-Star, received network
header from KB8PMY P/6017 to CQCQCQ
M: 2021-01-19 02:12:29.553 D-Star, received network
end of transmission, 2.7 seconds, 0% packet loss, BER:
0.0%
So with this I get no audio the Analog. But I get
analog to digital.
It I put the gateway to the port of repeater 2. I
get this error.
M: 2021-01-19 02:11:01.953 D-Star packet received
from an invalid source, A902000A != A902000A and/or
20028 != 20010
The correct reading above this one. to get it to
work. Gateway is 20010 and local address is 20028
; Analog_Bridge configuration file.
; This file should be placed in either /etc or it
can be
; supplied as a path on the Analog_Bridge command
line.
; The best way to think of this file is that there are
two main sections, the USRP (analog audio) and
; AMBE_AUDIO (compressed audio). Analog_Bridge will
take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port.
The encoder will use the format defined in ambeMode.
; As you might expect, the reverse direction is
defined too.
; Analog_Bridge supports include files. More on this
later...
include = dvsm.macro
; include = asl.macro
; General Section describes settings for Analog_Bridge
itself.
[GENERAL]
logLevel = 2 ; Show
messages and above 0=No logging, 1=Debug, 2=Message,
3=Info, 4=Warning, 5=Error, 6=Fatal
; Metadata management
exportMetadata = true ; Export
metadata to USRP partner (transcode setups require
this)
transferRootDir = /tmp ; Export database files to USRP
partner
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv
; DMR ID to callsign lookup data
; General vocoder setup information
decoderFallBack = false ; Allow
software AMBE decoding if a hardware decoder is not
found
useEmulator = true ; Use the
MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress =
127.0.0.1:2470
; IP address and port of the md380 server
pcmPort = 2222 ; UDP port to
send to the WebProxy
; Information for xx_Bridge (Where xx is MMDVM,
Quantar, HB, IPSC)
[AMBE_AUDIO]
address = 127.0.0.1 ; IP address
of xx_Bridge
txPort = 32103 ; Transmit TLV
frames to partner on this port
rxPort = 32100 ; Listen for
TLV frames from partner on this port
ambeMode = DSTAR ; DMR,
DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to
this format)
minTxTimeMS = 2500 ; Analog ->
Digital Minimum time in MS for hang delay (0-10000)
; The metadata below is used when ASL is the source
since it does not have any concept of digital modes
gatewayDmrId = 1139698 ; ID to use
when transmitting from Analog_Bridge 7 digit ID
repeaterID = 113969899 ; ID of source
repeater 7 digit ID plus 2 digit SSID
txTg = 2 ; TG to use for
all frames sent from Analog_Bridge -> xx_Bridge
txTs = 2 ; Slot to use
for frames sent from Analog_Bridge -> xx_Bridge
colorCode = 1 ; Color Code
to assign DMR frames
; Information for USRP channel driver. This interface
uses PCM to transfer audio information
; There are two typical configurations, ASL and
Transcode. ASL (AllstarLink) is for analog clients
connected
; to a digital network. Transcode is when
Analog_Bridge actually points its PCM interfaces back
at itself,
; causing a TLV <-- (pcm <--> pcm) --> TLV
type of architecture.
; When using ASL, this matches the rpt.conf ASL file
with a setting like:
; rxchannel = usrp/127.0.0.1:34001:32001
; When Transcoding, make two ini files and set
txPort equal to the other instance rxPort
(crossover). Launch
; each instance with its own ini file.
[USRP]
address = 127.0.0.1 ; IP address
of USRP partner (Allstar/Asterisk or another
Analog_Bridge)
txPort = 32001 ; Transmit
USRP frames on this port
rxPort = 34001 ; Listen for
USRP frames on this port
usrpAudio = AUDIO_UNITY ; Digital ->
Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)
usrpGain = 0.75 ; Gain factor
when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 =
AUDIO_UNITY)
usrpAGC = -20,10,100 ; Set the agc
threshold (db), slope (db) and decay (ms)
tlvAudio = AUDIO_UNITY ; Analog ->
Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain = 0.50 ; Gain factor
when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 =
AUDIO_UNITY)
[MACROS]
; Where the macros are
; xxxx=yyyy
; xxxx is the dial string to match
; yyyy is the command line to execute
; xxxx must be preceded by a *
; xxxx can be any string (alphanumeric)
; yyyy is the command to execute
; yyyy will replace xxxx in the dial string
; arguments follow the macro name with a # delimiter
; For example using macro "5678" above would look
like:
; *5678#9876
; Which would invoke:
; echo 9876
; Information for DV3000 hardware decoder
; There are two configuration modes: IP (AMBEServer)
and serial (direct connect hardware)
; Use top server and port if using AMBEServer
; Use bottom server/port and serial = true if using
the DV3000u (thumbdv)
; Did you run AMBETest4.py before using this?
[DV3000]
address = 10.0.2.229 ; IP address of
AMBEServer
rxPort = 2460 ; Port of
AMBEServer
; address = /dev/ttyUSB0 ; Device of
DV3000U on this machine
; baud = 460800 ; Baud rate of
the dongle (230400 or 460800)
; serial = true ; Use
serial=true for direct connect or serial=false for
AMBEServer
Audio is still bad. I am connected to 27539. I am
confused.