Can you look at this as well…..
I cannot get ASL<> AB to talk….Here
is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676
make it in the logs of AB and MB. When able to talk on
Allstar via Corey’s WS, I see the transmission in Allstar
but nothing past that.
Steve
; Your Repeater
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
[460310]
; Change this to your assigned node number
; Must also be enabled in modules.conf
; Rx audio/signalling channel. Choose ONLY 1 per node
stanza
; Enable the selected channel driver in modules.conf !!!
rxchannel =
dahdi/pseudo ; No radio (hub)
; rxchannel =
SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel =
Pi/1 ; Raspberry Pi PiTA
; rxchannel =
Radio/usb_1999 ; USBRadio (DSP)
; rxchannel =
Dahdi/1 ; PCI Quad card
; rxchannel =
Beagle/1 ; BeagleBoard
rxchannel =
USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel =
Voter/1999 ; RTCM device
duplex =
1 ; 0 = Half duplex with no
telemetry tones or hang time.
; Special Case: Full duplex if linktolink is set to
yes.
; This mode is preferred when interfacing with an
external multiport repeater controller.
; Comment out idrecording and idtalkover to suppress
IDs also
; 1 = Half duplex with telemetry tones and hang time. Does
not repeat audio.
; This mode is preferred when interfacing a simplex
node.
; 2 = Full Duplex with telemetry tones and hang time.
; This mode is preferred when interfacing a repeater.
; 3 = Full Duplex with telemetry tones and hang time, but
no repeated audio.
; 4 = Full Duplex with telemetry tones and hang time.
Repeated audio only when the autopatch is down.
linktolink =
no ; disables forcing physical
half-duplex operation of main repeater while
; still keeping half-duplex semantics (optional)
linkmongain =
0 ; Link Monitor Gain adjusts the
audio level of monitored nodes when a signal from another
node or the local receiver is received.
; If linkmongain is set to a negative number the monitored
audio will decrease by the set amount in db.
; If linkmongain set to a positive number monitored audio
will increase by the set amount in db.
; The value of linkmongain is in db. The default value is
0 db.
erxgain =
-3 ; Echolink receive gain
adjustment
; Note: Gain is in db-volts (20logVI/VO)
etxgain =
3 ; Echolink transmit gain
adjustment
; Note: Gain is in
db-volts (20logVI/VO)
;eannmode =
1 ; 1 = Say only node number on
echolink connects (default = 1)
; 2 = say phonetic call sign only on echolink connects
; 3 = say phonetic call sign and
node number on echolink connects
;controlstates =
controlstates ; system control state stanza
scheduler =
schedule ; scheduler stanza
functions =
functions ; Repeater Function stanza
phone_functions =
functions ; Phone Function stanza
link_functions =
functions ; Link Function stanza
telemetry =
telemetry ; Telemetry stanza
morse =
morse ; Morse stanza
wait_times =
wait-times ; Wait times stanza
context =
radio ; dialing context for phone
callerid =
"Repeater" <0000000000> ; callerid for phone
calls
accountcode =
RADIO ; account code (optional)
hangtime =
5000 ; squelch tail hang time (in
ms) (optional, default 5 seconds, 5000 ms)
althangtime =
4000 ; longer squelch tail
totime =
180000 ; transmit time-out time
(in ms) (optional, default 3 minutes 180000 ms)
idrecording =
|iWA4XYZ ; cording or morse string see http://ohnosec.org/drupal/node/87
idtalkover =
|iWA4XYZ ; Talkover ID (optional)
default is none see http://ohnosec.org/drupal/node/129
; See Telemetry section Example: idrecording =
rpt/nodenames/1999
idtime =
540000 ; id interval time (in ms)
(optional) Default 5 minutes (300000 ms)
politeid =
30000 ; time in milliseconds before
ID timer expires to try and ID in the tail. (optional,
default 30000)
unlinkedct =
ct2 ; Send a this courtesy tone
when the user unkeys if the node is not connected to any
other nodes. (optional, default is none)
remotect =
ct3 ; remote linked courtesy tone
(indicates a remote is in the list of links)
linkunkeyct =
ct8 ; sent when a transmission
received over the link unkeys
;nolocallinkct =
0 ; Send unlinkedct instead if
another local node is connected to this node (hosted on
the same PC).
;connpgm =
yourconnectprogram ; Disabled. Execute a program
you specify on connect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being connected to us (them)
;discpgm =
yourdisconnectprogram ; Disabled. Execute a program
you specify on disconnect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being disconnected from us (them)
;lnkactenable =
0 ; Set to 1 to enable the link
activity timer. Applicable to standard nodes only.
;lnkacttime =
1800 ; Link activity timer time in
seconds.
;lnkactmacro =
*52 ; Function to execute when link
activity timer expires.
;lnkacttimerwarn
= 30seconds ; Message to play when the link
activity timer has 30 seconds left.
;remote_inact_timeout
= ; Specifies the amount of time without
keying from the link. Set to 0 to disable timeout. (15 *
60)
;remote_timeout
= ; Session time out for remote
base. Set to 0 to disable. (60 * 60)
;remote_timeout_warning_freq
= ; 30
;remote_timeout_warning
= ; (3 * 60)
;nounkeyct =
0 ; Set to a 1 to eliminate
courtesy tones and associated delays.
holdofftelem =
0 ; Hold off all telemetry when
signal is present on receiver or from connected nodes
; except when an ID needs to be done and there is a signal
coming from a connected node.
telemdefault =
0 ; 0 = telemetry output off
; 1 = telemetry output on (default = 1)
; 2 = timed telemetry output on command execution and for
a short time thereafter.
telemdynamic =
1 ; 0 = disallow users to change
the local telemetry setting with a COP command,
; 1 = Allow users to change the setting with a COP
command. (default = 1)
;beaconing =
0 ; Send ID regardless of
repeater activity (Required in the UK, but probably
illegal in the US)
parrotmode =
0 ; 0 = Parrot Off (default = 0)
; 1 = Parrot On Command
; 2 = Parrot Always
; 3 = Parrot Once by Command
parrottime =
1000 ; Set the amount of time in
milliseconds
; to wait before parroting what was received
;rxnotch=1065,40
; (Optional) Notch a particular frequency for a specified
; b/w. app_rpt must have been compiled with
; the notch option
startup_macro =
; nodenames =
/var/lib/asterisk/sounds/rpt/nodenames.callsign ; Point
to alternate nodename sound directory
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Need more
information on these
;extnodes =
extnodes-different ; section in extnodefile containing
dynamic node information (optional)
;extnodefile =
/foo/nodes ; Points to nodelist file containing
dynamic node info default = /var/lib/asterisk/rpt_extnodes
(optional)
;extnodefile2
= ; Is this a list of node files? Possible
a list of private nodes or a list of static IPs for known
nodes????
;nodenames =
/foo/names ; locaton of node sound files default =
/var/lib/asterisk/sounds/rpt/nodenames
;archivedir =
/tmp ; defines and enables activity recording
into specified directory (optional)
;monminblocks =
2048 ; Min 1K blocks to be left on partition
(will not save monitor output if disk too full)
;
; The tailmessagetime,tailsquashedtime, and
tailmessagelist need to be set
;
; to support tail messages. They can be omitted otherwise.
;tailmessagetime
= 300000 ; Play a tail message every 5 mins
;tailsquashedtime
= 30000 ; If squashed by another user,
;
; try again after 30 seconds
;tailmessagelist
= msg1,msg2 ; list of messages to be played for tail
message
; alt_functions
; ctgroup
;
dphone_functions
; idtime
; iobase
; iospeed
; locallist
; mars
Remote Base
; memory
; nobusyout
; nodes
; nolocallinkct
; notelemtx
; outxlat
; parrot
;
propagate_phonedtmf
; rptnode
; rptinactmacro
Macro to execute when inactivity timer expires
; rptinacttime
Inactivity timer time in seconds (0 seconds disables
feature)
; rxnotch
Optional Audio notch
;
simplexphonedelay
; tonemacro
; tonezone
; txlimits
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; *** Status
Reporting ***
; Comment the
following statpost line stop to reporting of the status of
your node to stats.allstarlink.org
statpost_url = http://stats.allstarlink.org/uhandler
; Status updates
[functions]
; Prefix
Functions
; *1
Disconnect Link
; *2
Monitor Link
; *3
Connect Link
; *4
Command Mode
; *5
Macros
; *6
User Functions
; *7
Connection Status/Functions
; *8
User Functions
; *9
User Functions
; *0
User Functions
; *A
User Functions
; *B
User Functions
; *C
User Functions
; *D
User Functions
; Mandatory
Command Codes
; http://docs.allstarlink.org/drupal/node/91
1 =
ilink,1 ; Disconnect specified link
2 =
ilink,2 ; Connect specified link -- monitor
only
3 =
ilink,3 ; Connect specified link -- tranceive
4 =
ilink,4 ; Enter command mode on specified link
70 =
ilink,5 ; System status
99 =
cop,6 ; PTT (phone mode only)
; End Mandatory
Command Codes
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Macro Commands
5 = macro
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Autopatch
Commands
; Note, This may
be a good place for other 2 digit frequently used commands
61 =
autopatchup,noct = 1,farenddisconnect = 1,dialtime =
20000 ; Autopatch up
62 =
autopatchdn
; Autopatch down
; autopatchup can
optionally take comma delimited setting=value pairs:
; context =
string ; Override default context with
"string"
; dialtime =
ms ; Specify the max number of
milliseconds between phone number digits (1000
milliseconds = 1 second)
;
farenddisconnect = 1 ; Automatically disconnect
when called party hangs up
; noct =
1 ; Don't send repeater courtesy tone
during autopatch calls
; quiet =
1 ; Don't send dial tone, or connect
messages. Do not send patch down message when called party
hangs up
; Example:
123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Status Commands
; 1 - Force ID
(global)
; 2 - Give Time
of Day (global)
; 3 - Give
software Version (global)
; 4 - Give GPS
location info
; 5 - Last (dtmf)
user
; 11 - Force ID
(local only)
; 12 - Give Time
of Day (local only)
721 =
status,1 ; Force ID (global)
722 =
status,2 ; Give Time of Day (global)
723 =
status,3 ; Give software Version (global)
724 =
status,4 ; Give GPS location info
725 =
status,5 ; Last (dtmf) user
711 =
status,11 ; Force ID (local only)
712 =
status,12 ; Give Time of Day (local only)
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Link Commands
; 1 - Disconnect
specified link
; 2 - Connect
specified link -- monitor only
; 3 - Connect
specified link -- tranceive
; 4 - Enter
command mode on specified link
; 5 - System
status
; 6 - Disconnect
all links
; 7 - Last Node
to Key Up
; 8 - Connect
specified link -- local monitor only
; 9 - Send Text
Message (9,<destnodeno or 0 (for all)>,Message Text,
etc.
; 10 - Disconnect
all RANGER links (except permalinks)
; 11 - Disconnect
a previously permanently connected link
; 12 -
Permanently connect specified link -- monitor only
; 13 -
Permanently connect specified link -- tranceive
; 15 - Full
system status (all nodes)
; 16 - Reconnect
links disconnected with "disconnect all links"
; 17 - MDC test
(for diag purposes)
; 18 -
Permanently Connect specified link -- local monitor only
; ilink commands
1 through 5 are defined in the Mandatory Command section
806 =
ilink,6 ; Disconnect all links
807 =
ilink,7 ; Last Node to Key Up
808 =
ilink,8 ; Connect specified link --
local monitor only
809 =
ilink,9,1999,"Testing" ; would send a text message to
node 1999 replace 1999 with 0 for all connected nodes
810 =
ilink,10 ; Disconnect all RANGER links
(except permalinks)
811 =
ilink,11 ; Disconnect a previously
permanently connected link
812 =
ilink,12 ; Permanently connect specified
link -- monitor only
813 =
ilink,13 ; Permanently connect specified
link -- tranceive
815 =
ilink,15 ; Full system status (all nodes)
816 =
ilink,16 ; Reconnect links disconnected
with "disconnect all links"
817 =
ilink,17 ; MDC test (for diag purposes)
818 = ilink
18 ; Permanently Connect specified link
-- local monitor only
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Control
operator (cop) functions. Change these to something other
than these codes listed below!
901 =
cop,1 �� ; System warm boot
902 =
cop,2 ; System enable
903 =
cop,3 ; System disable
904 =
cop,4 ; Test tone on/off
(toggle)
905 =
cop,5 ; Dump system variables
on console (debug use only)
907 =
cop,7 ; Time out timer enable
908 =
cop,8 ; Time out timer disable
909 =
cop,9 ; Autopatch enable
910 =
cop,10 ; Autopatch disable
911 =
cop,11 ; User linking functions
enable
912 =
cop,12 ; User linking functions
disable
913 =
cop,13 ; Query system control
state
914 =
cop,14 ; Set system control
state
915 = cop,15
; Scheduler enable
916 =
cop,16 ; Scheduler disable
917 =
cop,17 ; User functions enable
(time, id, etc)
918 =
cop,18 ; User functions disable
919 =
cop,19 ; Select alternate hang
time (althangtime)
920 =
cop,20 ; Select standard
hangtime (hangtime)
921 =
cop,21 ; Enable Parrot Mode
922 =
cop,22 ; Disable Parrot Mode
923 =
cop,23 ; Birdbath (Current
Parrot Cleanup/Flush)
924 =
cop,24 ; Flush all telemetry
925 =
cop,25 ; Query last node
un-keyed
926 =
cop,26 ; Query all nodes
keyed/unkeyed
927 =
cop,27 ; Reset DAQ minimum on a
pin
928 =
cop,28 ; Reset DAQ maximum on a
pin
930 =
cop,30 ; Recall Memory Setting
in Attached Xcvr
931 =
cop,31 ; Channel Selector for
Parallel Programmed Xcvr
932 =
cop,32 ; Touchtone pad test:
command + Digit string + # to playback all digits pressed
933 =
cop,33 ; Local Telemetry Output
Enable
934 =
cop,34 ; Local Telemetry Output
Disable
935 =
cop,35 ; Local Telemetry Output
on Demand
936 =
cop,36 ; Foreign Link Local
Output Path Enable
937 =
cop,37 ; Foreign Link Local
Output Path Disable
938 =
cop,38 ; Foreign Link Local
Output Path Follows Local Telemetry
939 =
cop,39 ; Foreign Link Local
Output Path on Demand
942 =
cop,42 ; Echolink announce node
# only
943 =
cop,43 ; Echolink announce node
Callsign only
944 =
cop,44 ; Echolink announce node
# & Callsign
945 =
cop,45 ; Link Activity timer
enable
945 =
cop,46 ; Link Activity timer
disable
947 =
cop,47 ; Reset "Link Config
Changed" Flag
948 =
cop,48 ; Send Page Tone (Tone
specs separated by parenthesis)
949 =
cop,49 ; Disable incoming
connections (control state noice)
950 =
cop,50 ; Enable incoming
connections (control state noicd)
951 =
cop,51 ; Enable sleep mode
952 =
cop,52 ; Disable sleep mode
953 =
cop,53 ; Wake up from sleep
954 =
cop,54 ; Go to sleep
955 =
cop,55 ; Parrot Once if parrot
mode is disabled
956 =
cop,56 ; Rx CTCSS Enable
957 = cop,57
; Rx CTCSS Disable
958 =
cop.58 ; Tx CTCSS On Input only
Enable
959 =
cop,59 ; Tx CTCSS On Input only
Disable
960 =
cop,60 ; Send MDC-1200 Burst
(cop,60,type,UnitID[,DestID,SubCode])
; Type is 'I' for PttID, 'E' for Emergency, and 'C' for
Call
; (SelCall or Alert), or 'SX' for STS (ststus), where X is
0-F.
; DestID and subcode are only specified for the 'C' type
message.
; UnitID is the local systems UnitID. DestID is the
MDC1200 ID of
; the radio being called, and the subcodes are as follows:
; Subcode '8205' is Voice Selective Call for Spectra
('Call')
; Subcode '8015' is Voice Selective Call for Maxtrac
('SC') or
; Astro-Saber('Call')
; Subcode '810D' is Call Alert (like Maxtrac 'CA')
961 =
cop,61 ; Send Message to USB to
control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)
962 =
cop,62 ; Send Message to USB to
control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)
963 =
cop,63 ; Send pre-configred
APRSTT notification (cop,63,CALL[,OVERLAYCHR])
964 =
cop,64 ; Send pre-configred
APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])
965 =
cop,65 ; Send POCSAG page
(equipped channel types only)
[functions-remote]
0 =
remote,1 ; Retrieve Memory
1 =
remote,2 ; Set freq.
2 =
remote,3 ; Set tx PL tone
3 =
remote,4 ; Set rx PL tone
40 =
remote,100 ; Rx PL off
41 =
remote,101 ; Rx PL on
42 =
remote,102 ; Tx PL off
43 =
remote,103 ; Tx PL on
44 =
remote,104 ; Low Power
45 =
remote,105 ; Medium Power
46 =
remote,106 ; High Power
711 =
remote,107 ; Bump -20
714 =
remote,108 ; Bump -100
717 =
remote,109 ; Bump -500
713 =
remote,110 ; Bump +20
716 =
remote,111 ; Bump +100
719 =
remote,112 ; Bump +500
721 =
remote,113 ; Scan - slow
724 =
remote,114 ; Scan - quick
727 =
remote,115 ; Scan - fast
723 =
remote,116 ; Scan + slow
726 =
remote,117 ; Scan + quick
729 =
remote,118 ; Scan + fast
79 =
remote,119 ; Tune
51 =
remote,5 ; Long status query
52 =
remote,140 ; Short status query
67 =
remote,210 ; Send a *
69 =
remote,211 ; Send a #
;91 =
remote,99,CALLSIGN,LICENSETAG ; Remote base login.
; Define a different dtmf sequence for each user which is
; authorized to use the remote base to control access to
it.
; For examble 9139583=remote,99,WB6NIL,G would grant
access to
; the remote base and announce WB6NIL as being logged in.
; Another entry, 9148351=remote,99,WA6ZFT,E would grant
access to
; the remote base and
announce WA6ZFT as being logged in.
; When the remote base is disconnected from the
originating node, the
; user will be logged out. The LICENSETAG argument is used
to enforce
; tx frequency limits. See [txlimits] below.
85 =
cop,6 ; Remote base telephone
key
[telemetry]
; Telemetry
entries can be shared across all repeaters, or defined for
each repeater.
; Can be a tone
sequence, morse string, or a file
;
; |t - Tone
escape sequence
;
; Tone sequences
consist of 1 or more 4-tuple entries (freq1, freq2,
duration, amplitude)
; Single
frequencies are created by setting freq1 or freq2 to zero.
;
; |m - Morse
escape sequence
;
; Sends Morse
code at the telemetry amplitude and telemetry frequency as
defined in the
; [morse]
section.
;
; Follow with an
alphanumeric string
;
; |i - Morse ID
escape sequence
;
; Sends Morse
code at the ID amplitude and ID frequency as defined in
the
; [morse]
section.
;
;
path/to/sound/file/without/extension
;
; Send the sound
if in place of a constructed tone. Do not include the file
extension
; Example: ct8 =
rpt/bloop
; Example:
idrecording = rpt/nodenames/1999
ct1 =
|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2 =
|t(660,880,150,2048)
ct3 =
|t(440,0,150,4096)
ct4 =
|t(550,0,150,2048)
ct5 =
|t(660,0,150,2048)
ct6 =
|t(880,0,150,2048)
ct7 =
|t(660,440,150,2048)
ct8 =
|t(700,1100,150,2048)
ranger =
|t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)
remotemon =
|t(1209,0,50,2048) ;
local courtesy tone when receive only
remotetx =
|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ;
local courtesy tone when linked Trancieve mode
cmdmode =
|t(900,903,200,2048)
functcomplete =
|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
remcomplete =
|t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)
pfxtone =
|t(350,440,30000,3072)
patchup =
rpt/callproceeding
patchdown =
rpt/callterminated
; As far as what
the numbers mean,
;
(000,000,010,000)
; | | |
|-------amplitude
; | |
|-------------duration
; |
|-------------------Tone 2
;
|-------------------------Tone 1
; So, with
0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0
Amplitude.
; Use it for a
delay. Fine tuning for how long before telemetry is sent,
in conjunction with the telemdelay parameter)
; The numbers,
like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay,
amplitude of 2048.
; Morse code
parameters, these are common to all repeaters.
[morse]
speed =
20 ; Approximate speed in WPM
frequency =
800 ; Morse Telemetry Frequency
amplitude =
4096 ; Morse Telemetry Amplitude
idfrequency =
1065 ; Morse ID Frequency
idamplitude =
1024 ; Morse ID Amplitude
;
; This section
allows wait times for telemetry events to be adjusted
; A section for
wait times can be defined for every repeater
;
[wait-times]
telemwait =
2000 ; Time to wait before sending
most telemetry
idwait =
500 ; Time to wait before
starting ID
unkeywait =
2000 ; Time to wait after unkey
before sending CT's and link telemetry
calltermwait =
2000 ; Time to wait before announcing
"call terminated"
;
; This is where
you define your nodes which cam be connected to.
;
[nodes]
; Note, if you
are using automatic update for allstar link nodes,
; no allstar link
nodes should be defined here. Only place a definition
; for your local
nodes, and private (off of allstar link) nodes here.
460310 = radio@....0.1:4569/460310,NONE
; This must be changed to your node number
; and iax port number if not the default
; Memories for
remote bases
[memory]
;00 =
146.580,100.0,m
;01 =
147.030,103.5,m+t
;02 =
147.240,103.5,m+t
;03 =
147.765,79.7,m-t
;04 =
146.460,100.0,m
;05 =
146.550,100.0,m
; Place command
macros here
[macro]
;1 = *32011#
;2 =
*12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#
;3 =
*32001*32011*32050*32030*32060#
; Data
Acquisition configuration
;[daq-list]
;device =
device_name1
;device =
device_name2
;Where:
device_name1 and device_name2 are stanzas you define in
this file
;device =
daq-cham-1
; Device name
;[daq-cham-1]
; Defined in [daq-list]
;hwtype =
uchameleon ; DAQ hardware type
;devnode =
/dev/ttyUSB0 ; DAQ device node (if
required)
;1 =
inadc ; Pin definition for an
ADC channel
;2 = inadc
;3 = inadc
;4 = inadc
;5 = inadc
;6 = inadc
;7 = inadc
;8 = inadc
;9 =
inp ; Pin definition for an
input with a weak pullup resistor
;10 = inp
;11 = inp
;12 = inp
;13 =
in ; Pin definition for an
input without a weak pullup resistor
;14 =
out ; Pin definition for an
output
;15 = out
;16 = out
;17 = out
;18 = out
;[meter-faces]
;face =
scale(scalepre,scalediv,scalepost),word/?,...
;
; scalepre =
offset to add before dividing with scalediv
; scalediv = full
scale/number of whole units (e.g. 256/20 or 12.8 for 20
volts).
; scalepost =
offset to add after dividing with scalediv
;
;face =
range(X-Y:word,X2-Y2:word,...),word/?,...
;face =
bit(low-word,high-word),word/?,...
;
; word/? is
either a word in /var/lib/asterisk/sounds or one of its
subdirectories,
; or a question
mark which is a placeholder for the measured value.
;
;
; Battery voltage
0-20 volts
;batvolts =
scale(0,12.8,0),rpt/thevoltageis,?,ha/volts
; 4 quadrant wind
direction
;winddir =
range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?
; LM34
temperature sensor with 130 deg. F full scale
;lm34f =
scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit
; Status poll
(non alarmed)
;light =
bit(ha/off,ha/on),ha/light,?
;[alarms]
;
;tag =
device,pin,node,ignorefirst,func-low,func-hi
;
;tag = a unique
name for the alarm
;device = daq
device to poll
;pin = the device
pin to be monitored
;ignorefirstalarm
= set to 1 to throwaway first alarm event, or 0 to report
it
;node = the node
number to execute the function on
;func-low = the
DTMF function to execute on a high to low transition
;func-high = the
DTMF function to execute on a low to high transition
;
; a '-' as a
function name is shorthand for no-operation
;
;door =
daq-cham-1,9,1,2017,*7,-
;pwrfail =
daq-cham-1,10,0,2017,*911111,-
;
; Control states
; Allow several
control operator functions to be changed at once using one
command (good for scheduling)
;
;[controlstates]
;statenum =
copcmd,[copcmd]...
;0 =
rptena,lnkena,apena,totena,ufena,noicd ; Normal operation
;1 =
rptena,lnkena,apdis,totdis,ufena,noice ; Net and news
operation
;2 =
rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only
operation
; Scheduler -
execute a macro at a given time
[schedule]
;dtmf_function =
m h dom mon dow ; ala cron, star is implied
;2 = 00 00 * *
* ; at midnight, execute macro 2.
#includeifexists
custom/rpt.conf
Analog_Bridge.ini
; Analog_Bridge
configuration file.
; This file
should be placed in either /etc or it can be
; supplied as a
path on the Analog_Bridge command line.
; The best way to
think of this file is that there are two main sections,
the USRP (analog audio) and
; AMBE_AUDIO
(compressed audio). Analog_Bridge will take everything
sent to the USRP port and
; encode it for
transmission on the AMBE_AUDIO port. The encoder will use
the format defined in ambeMode.
; As you might
expect, the reverse direction is defined too.
; Analog_Bridge
supports include files. More on this later...
include =
dvsm.macro
; include =
asl.macro
; General Section
describes settings for Analog_Bridge itself.
[GENERAL]
logLevel =
2 ; Show messages and above
0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning,
5=Error, 6=Fatal
; Metadata
management
exportMetadata =
true ; Export metadata to USRP partner
(transcode setups require this)
transferRootDir =
/tmp ; Export database files to USRP
partner
subscriberFile =
/var/lib/dvswitch/subscriber_ids.csv ; DMR ID to
callsign lookup data
; General vocoder
setup information
decoderFallBack =
true ; Allow software AMBE decoding if a
hardware decoder is not found
useEmulator =
false ; Use the MD380 AMBE emulator
for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress =
127.0.0.1:2470 ; IP address and port of the md380
server
pcmPort =
2222 ; UDP port to send to the
WebProxy
; Information for
xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address =
127.0.0.1 ; IP address of xx_Bridge
txPort =
31103 ; Transmit TLV frames to
partner on this port
rxPort =
31100 ; Listen for TLV frames
from partner on this port
ambeMode =
DMR ; DMR, DMR_IPSC, DSTAR, NXDN,
P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS =
2500 ; Analog -> Digital Minimum
time in MS for hang delay (0-10000)
; The metadata
below is used when ASL is the source since it does not
have any concept of digital modes
gatewayDmrId =
1112721 ; ID to use when transmitting
from Analog_Bridge 7 digit ID
repeaterID =
111272123 ; ID of source repeater 7 digit
ID plus 2 digit SSID
txTg =
31676 ; TG to use for all
frames sent from Analog_Bridge -> xx_Bridge
txTs =
2 ; Slot to use for frames
sent from Analog_Bridge -> xx_Bridge
colorCode =
1 ; Color Code to assign DMR
frames
; Information for
USRP channel driver. This interface uses PCM to transfer
audio information
; There are two
typical configurations, ASL and Transcode. ASL
(AllstarLink) is for analog clients connected
; to a digital
network. Transcode is when Analog_Bridge actually points
its PCM interfaces back at itself,
; causing a TLV
<-- (pcm <--> pcm) --> TLV type of
architecture.
; When using
ASL, this matches the rpt.conf ASL file with a setting
like:
; rxchannel =
usrp/127.0.0.1:34001:32001
; When
Transcoding, make two ini files and set txPort equal to
the other instance rxPort (crossover). Launch
; each instance
with its own ini file.
[USRP]
address =
127.0.0.1 ; IP address of USRP partner
(Allstar/Asterisk or another Analog_Bridge)
txPort =
32001 ; Transmit USRP frames on
this port
rxPort =
34001 ; Listen for USRP frames on
this port
usrpAudio =
AUDIO_UNITY ; Digital -> Analog
(AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)
usrpGain =
1.10 ; Gain factor when usrpAudio
= AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
usrpAGC =
-20,10,100 ; Set the agc threshold
(db), slope (db) and decay (ms)
tlvAudio =
AUDIO_UNITY ; Analog -> Digital
(AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain =
0.35 ; Gain factor when tlvAudio
= AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
[MACROS]
; Where the
macros are
; xxxx=yyyy
; xxxx is the
dial string to match
; yyyy is the
command line to execute
; xxxx must be
preceded by a *
; xxxx can be any
string (alphanumeric)
; yyyy is the
command to execute
; yyyy will
replace xxxx in the dial string
; arguments
follow the macro name with a # delimiter
; For example
using macro "5678" above would look like:
; *5678#9876
; Which would
invoke:
; echo 9876
; Information for
DV3000 hardware decoder
; There are two
configuration modes: IP (AMBEServer) and serial (direct
connect hardware)
; Use top
server and port if using AMBEServer
; Use bottom
server/port and serial = true if using the DV3000u
(thumbdv)
; Did you run
AMBETest4.py before using this?
[DV3000]
address =
127.0.0.1 ; IP address of AMBEServer
rxPort =
2460 ; Port of AMBEServer
; address =
/dev/ttyUSB0 ; Device of DV3000U on this
machine
; baud =
460800 ; Baud rate of the dongle
(230400 or 460800)
; serial =
true ; Use serial=true f
