Home Messages Hashtags Subgroups Wiki

Welcome to DVSwitch

DVSwitch is a set of tools and programs related to provisioning and operating Amateur Radio digital voice networks.

Purpose

The purpose of DVSwitch is as follows:

1) Allows “local” networking during an outage of the regional national/international network server.
2) Allows a local network operator to “blend” upstream feeds from different Networks (capital N on purpose). These Networks can’t get their act together and learn how to play nice with each other (everyone guilty as far as we are concerned). They may not like people doing this, but the solution is to grow up and work with each other, and not keep trying to force people to take sides.
3) Allows local segregation of localized traffic with more flexibility.
4) Allows experimentation with linking and how it’s done (part 97 specifies experimentation and advancement of the radio art are a core part of amateur radio).

Mission Statement/Position

Our stated position is:

WHEREAS the Networks continue to be largely islands and are not working together to create a unified network of Networks.
WHEREAS no firm reason has been given by any of the Networks why a *competent* local network operator cannot make this work effectively.

(US ONLY)
WHEREAS 47 CFR 97 (Amateur Radio Service) specifies that a core component of amateur radio is experimentation and advancement of the radio art [97.1(b)].

BE IT RESOLVED the core group of US amateur radio operators and experimenters organized around the DVSwitch project, and in the spirit of USA 47 CFR 97 and its intentions, support the *responsible* and *thoughtful* use of digital voice networking tools to create localized networks that will interconnect to the national/international Networks, and will support users of its tools in order to do this in the most effective and sustainable way possible.

Between

and

Re: Analog_Bridge.ini Jeff Carrier #1426 Steve, You mentioned something yesterday that created a question in my mind. You said USRP and SimpleUSB can't run together on the same box. I'm assuming that has something to do with those two channel drivers in asterisk. My install seems to be fine less the complaints about "digital sounding audio" but I'm running Analog_Bridge, MMDVM_Bridge and P25Gateway on the same Pi as an allstar node with URIx connected running DSP. It seems fine but does this have the potential to cause erratic behavior? toggle quoted messageShow quoted text On Thu, May 31, 2018 at 7:20 AM Steve N4IRS <szingman@...> wrote: We are working to simplify and standardize the configuration files across all the Partner programs. Analog_Bridge.ini is one of the oldest and needs a little facelift to better match the other partners. Though some of the parameter names are changing, the old names will be supported for a while. If you are still using the older names, you will get a warning in the Analog_Bridge log. Your configuration will continue to operate as before. I have bolded the changes parameters Here is the updated Analog_Bridge.ini: ; Analog_Bridge configuration file. ; This file should be placed in either /etc or it can be ; supplied as a path on the Analog_Bridge command line. ; The best way to think of this file is that there are two main sections, the USRP (analog audio) and ; AMBE_AUDIO (compressed audio). Analog_Bridge will take everything sent to the USRP port and ; encode it for transmission on the AMBE_AUDIO port. The encoder will use the format defined in ambeMode. ; As you might expect, the reverse direction is defined too. ; General Section describes settings for Analog_Bridge itself. [GENERAL] logLevel = 2 ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal ; Metadata management subscriberFile = ./subscriber_ids.csv ; DMR ID to callsign lookup data exportMetadata = true ; Export metadata to USRP partner (transcode setups require this) ; General vocoder setup information decoderFallBack = false ; Allow software AMBE decoding if a hardware decoder is not found useEmulator = false ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN) emulatorAddress = 127.0.0.1:2470 ; IP address and port of the md380 server ; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC) [AMBE_AUDIO] address = 127.0.0.1 ; IP address of xx_Bridge txPort = 31003 ; Transmit TLV frames to partner on this port rxPort = 31000 ; Listen for TLV frames from partner on this port ambeMode = DMR ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format) minTxTimeMS = 2000 ; Minimum time in MS for hang delay (0-10000) ; The metadata below is used when ASL is the source since it does not have any concept of digital modes gatewayDmrId = 0 ; ID to use when transmitting from Analog_Bridge repeaterID = 0 ; ID of source repeater txTg = 9 ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge txTs = 2 ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge colorCode = 1 ; Color Code to assign DMR frames ; Information for USRP channel driver. This interface uses PCM to transfer audio information ; There are two typical configurations, ASL and Transcode. ASL (AllstarLink) is for analog clients connected ; to a digital network. Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, ; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture. ; When using ASL, this matches the rpt.conf ASL file with a setting like: ; rxchannel = usrp/127.0.0.1:34001:32001 ; When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover). Launch ; each instance with its own ini file. [USRP] address = 127.0.0.1 ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge) txPort = 32001 ; Transmit USRP frames on this port rxPort = 34001 ; Listen for USRP frames on this port aslAudio = AUDIO_UNITY ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) agcGain = -20 ; Gain (in db) of the AGC filter dmrAudio = AUDIO_UNITY ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) dmrGain = 0.35 ; Gain factor of audio from ASL (0.0-1.0) ; Information for DV3000 hardware decoder ; There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware) ; Use top server and port if using AMBEServer ; Use bottom server/port and serial = true if using the DV3000u (thumbdv) ; Did you run AMBETest4.py before using this? [DV3000] address = 127.0.0.1 ; IP address of AMBEServer rxPort = 2460 ; Port of AMBEServer ; address = /dev/ttyUSB0 ; Device of DV3000U on this machine ; baud = 460800 ; Baud rate of the dongle (230400 or 460800) ; serial = true ; Use serial=true for direct connect or serial=false for AMBEServer
More All Messages By This Member
Analog_Bridge.ini Steve N4IRS #1425 We are working to simplify and standardize the configuration files across all the Partner programs. Analog_Bridge.ini is one of the oldest and needs a little facelift to better match the other partners. Though some of the parameter names are changing, the old names will be supported for a while. If you are still using the older names, you will get a warning in the Analog_Bridge log. Your configuration will continue to operate as before. I have bolded the changes parameters Here is the updated Analog_Bridge.ini: ; Analog_Bridge configuration file. ; This file should be placed in either /etc or it can be ; supplied as a path on the Analog_Bridge command line. ; The best way to think of this file is that there are two main sections, the USRP (analog audio) and ; AMBE_AUDIO (compressed audio). Analog_Bridge will take everything sent to the USRP port and ; encode it for transmission on the AMBE_AUDIO port. The encoder will use the format defined in ambeMode. ; As you might expect, the reverse direction is defined too. ; General Section describes settings for Analog_Bridge itself. [GENERAL] logLevel = 2 ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal ; Metadata management subscriberFile = ./subscriber_ids.csv ; DMR ID to callsign lookup data exportMetadata = true ; Export metadata to USRP partner (transcode setups require this) ; General vocoder setup information decoderFallBack = false ; Allow software AMBE decoding if a hardware decoder is not found useEmulator = false ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN) emulatorAddress = 127.0.0.1:2470 ; IP address and port of the md380 server ; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC) [AMBE_AUDIO] address = 127.0.0.1 ; IP address of xx_Bridge txPort = 31003 ; Transmit TLV frames to partner on this port rxPort = 31000 ; Listen for TLV frames from partner on this port ambeMode = DMR ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format) minTxTimeMS = 2000 ; Minimum time in MS for hang delay (0-10000) ; The metadata below is used when ASL is the source since it does not have any concept of digital modes gatewayDmrId = 0 ; ID to use when transmitting from Analog_Bridge repeaterID = 0 ; ID of source repeater txTg = 9 ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge txTs = 2 ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge colorCode = 1 ; Color Code to assign DMR frames ; Information for USRP channel driver. This interface uses PCM to transfer audio information ; There are two typical configurations, ASL and Transcode. ASL (AllstarLink) is for analog clients connected ; to a digital network. Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, ; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture. ; When using ASL, this matches the rpt.conf ASL file with a setting like: ; rxchannel = usrp/127.0.0.1:34001:32001 ; When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover). Launch ; each instance with its own ini file. [USRP] address = 127.0.0.1 ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge) txPort = 32001 ; Transmit USRP frames on this port rxPort = 34001 ; Listen for USRP frames on this port aslAudio = AUDIO_UNITY ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) agcGain = -20 ; Gain (in db) of the AGC filter dmrAudio = AUDIO_UNITY ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) dmrGain = 0.35 ; Gain factor of audio from ASL (0.0-1.0) ; Information for DV3000 hardware decoder ; There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware) ; Use top server and port if using AMBEServer ; Use bottom server/port and serial = true if using the DV3000u (thumbdv) ; Did you run AMBETest4.py before using this? [DV3000] address = 127.0.0.1 ; IP address of AMBEServer rxPort = 2460 ; Port of AMBEServer ; address = /dev/ttyUSB0 ; Device of DV3000U on this machine ; baud = 460800 ; Baud rate of the dongle (230400 or 460800) ; serial = true ; Use serial=true for direct connect or serial=false for AMBEServer
More All Messages By This Member
Re: Rpi3 Bridge Steve N4IRS #1424 In Analog_Bridge.ini Do not use the same ID for both gatewayDmrId and repeaterID I suggest the gatewayDmrId should be your 7 digit DMR ID Run MMDVM_Bridge MMDVM_Bridge.ini in /opt/MMDVM_Bridge. This is what logs into BM. See what the output is. Steve toggle quoted messageShow quoted text On 5/31/2018 8:55 AM, kc5mmw@... wrote: Could you help me find what is broken? I can connect to my other node from asl. I do not see the id's i chose in my brandmiester hotspot list ; Analog_Bridge configuration file. ; This file should be placed in either /etc or it can be ; supplied as a path on the Analog_Bridge command line. ; General Section describes settings for Analog_Bridge itself. ; For RPI, don't forget to modprobe snd_pcm_oss to get the devices populated [GENERAL] logLevel = 2 ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal ; Metadata management exportMetadata = true ; Export metadata to USRP partner (transcode setups require this) subscriberFile = /var/lib/dvswitch/subscriber_ids.csv ; DMR ID to callsign lookup data ; General vocoder setup information decoderFallBack = true ; Allow software AMBE decoding if a hardware decoder is not found useEmulator = true ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN) emulatorAddress = 127.0.0.1:2470 ; IP address and port of the server ; Audio devices are normally not needed when in gateway service. These devices should ; only be set when local monitor or dongle modes are required. outputAudioDevice = /dev/null ; Audio device /dev/null, /dev/dsp1, portaudio, etc inputAudioDevice = /dev/null ; Only used for dongle mode ; Below values are for using this as a local DMR dongle (no ASL needed) useMicrophone = false ; Use app as just a fancy dongle for DMR useVox = false ; If using dongle mode (useMicrophone), enable VOX voxDecay = 2 ; Hang time in seconds voxTrigger = 200 ; Value to trip PTT (0-32767) ; Information for xx_Bridges (Where xx is MMDVM, HB, IPSC) [AMBE_AUDIO] server = 127.0.0.1 ; IP address of xx_Bridge.py fromDMRPort = 31100 ; AMBE frames from xx_Bridge (should match "toGatewayPort" in xx_Bridge.cfg) toDMRPort = 31103 ; AMBE frames from xx_Bridge (should match "fromGatewayPort" in xx_Bridge.cfg) ambeMode = DMR ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW minTxTimeMS = 2000 ; Minimum time in MS for hang delay gatewayDmrId = 310502480 ; ID to use when transmitting from Analog_Bridge repeaterID = 310502480 ; ID of source repeater txTg = 31055 ; TG to use for all frames received from Analog_Bridge -> xx_Bridge txTs = 2 ; Slot to use for frames received from Analog_Bridge -> xx_Bridge colorCode = 1 ; Color Code to assign DMR frames ; Information for USRP channel driver. This interface uses PCM to transfer audio information ; There are two typical configurations, ASL and Transcode. ASL (AllstarLink) is for analog clients connected ; to a digital network. Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, ; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture. ; When using ASL, this matches the rpt.conf ASL file with a setting like: ; rxchannel = usrp/127.0.0.1:34001:32001 ; When Transcoding, make toASLPort equal to the other instance fromASLPort (crossover) [USRP] server = 127.0.0.1 ; IP address of Allstar/Asterisk toASLPort = 32001 ; Analog_Bridge <-- ASL fromASLPort = 34001 ; Analog_Bridge --> ASL aslAudio = AUDIO_UNITY ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) agcGain = -10 ; Gain (in db) of the AGC filter dmrAudio = AUDIO_UNITY ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) dmrGain = 0.25 ; Gain factor of audio from ASL (0.0-1.0) ; Information for DV3000 hardware decoder ; There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware) ; Use top server and port if using AMBEServer ; Use bottom server/port and serial = true if using the DV3000u (thumbdv) ; Did you run AMBETest4.py before using this? [DV3000] server = 127.0.0.1 ; IP address of AMBEServer port = 2460 ; Port of AMBEServer ; server = /dev/ttyUSB0 ; Device of DV3000U on this machine ; port = 460800 ; Baud rate of the dongle ; serial = true ; Use serial (DV3000U) or IP [General] Callsign=KC5MMW Id=310502480 Timeout=180 Duplex=0 ModeHang=0 RFModeHang=0 NetModeHang=0 Display=None Daemon=0 [Info] RXFrequency=222340000 TXFrequency=224940000 Power=1 Latitude=41.7333 Longitude=-50.3999 Height=0 Location=Iceberg, North Atlantic Description=MMDVM_Bridge URL=https://groups.io/g/DVSwitch [Log] # Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal DisplayLevel=1 FileLevel=2 FilePath=/var/log/mmdvm FileRoot=MMDVM_Bridge [DMR Id Lookup] File=/var/lib/mmdvm/DMRIds.dat Time=24 [NXDN Id Lookup] File=/var/lib/mmdvm/NXDN.csv Time=24 [Modem] Port=/dev/null RSSIMappingFile=RSSI.dat Trace=0 Debug=0 [D-Star] Enable=0 Module=C SelfOnly=0 AckReply=1 AckTime=750 ErrorReply=1 RemoteGateway=0 ModeHang=0 [DMR] Enable=1 Beacons=0 BeaconInterval=60 BeaconDuration=3 ColorCode=1 SelfOnly=0 EmbeddedLCOnly=1 DumpTAData=0 CallHang=0 TXHang=0 ModeHang=0 [System Fusion] Enable=0 LowDeviation=0 SelfOnly=0 RemoteGateway=0 ModeHang=0 [P25] Enable=0 NAC=293 SelfOnly=0 OverrideUIDCheck=0 RemoteGateway=0 ModeHang=0 [NXDN] Enable=0 RAN=1 SelfOnly=0 RemoteGateway=0 ModeHang=0 Id=12345 [D-Star Network] Enable=0 GatewayAddress=127.0.0.1 GatewayPort=20010 LocalPort=20011 ModeHang=0 Debug=0 [DMR Network] Enable=1 Address=3103.repeater.net Port=62031 Jitter=750 Local=62032 Password=passw0rd Slot1=1 Slot2=1 ModeHang=0 Debug=0 [System Fusion Network] Enable=0 LocalAddress=0 LocalPort=3200 GatewayAddress=127.0.0.1 GatewayPort=42000 ModeHang=0 Debug=0 [P25 Network] Enable=0 GatewayAddress=127.0.0.1 GatewayPort=42020 LocalPort=32010 ModeHang=0 Debug=0 [NXDN Network] Enable=0 #LocalAddress=127.0.0.1 ModeHang=0 Debug=0 LocalPort=14021 GatewayAddress=127.0.0.1 GatewayPort=14020
More All Messages By This Member
Re: Rpi3 Bridge Justin Morris #1423 Could you help me find what is broken? I can connect to my other node from asl. I do not see the id's i chose in my brandmiester hotspot list ; Analog_Bridge configuration file. ; This file should be placed in either /etc or it can be ; supplied as a path on the Analog_Bridge command line. ; General Section describes settings for Analog_Bridge itself. ; For RPI, don't forget to modprobe snd_pcm_oss to get the devices populated [GENERAL] logLevel = 2 ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal ; Metadata management exportMetadata = true ; Export metadata to USRP partner (transcode setups require this) subscriberFile = /var/lib/dvswitch/subscriber_ids.csv ; DMR ID to callsign lookup data ; General vocoder setup information decoderFallBack = true ; Allow software AMBE decoding if a hardware decoder is not found useEmulator = true ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN) emulatorAddress = 127.0.0.1:2470 ; IP address and port of the server ; Audio devices are normally not needed when in gateway service. These devices should ; only be set when local monitor or dongle modes are required. outputAudioDevice = /dev/null ; Audio device /dev/null, /dev/dsp1, portaudio, etc inputAudioDevice = /dev/null ; Only used for dongle mode ; Below values are for using this as a local DMR dongle (no ASL needed) useMicrophone = false ; Use app as just a fancy dongle for DMR useVox = false ; If using dongle mode (useMicrophone), enable VOX voxDecay = 2 ; Hang time in seconds voxTrigger = 200 ; Value to trip PTT (0-32767) ; Information for xx_Bridges (Where xx is MMDVM, HB, IPSC) [AMBE_AUDIO] server = 127.0.0.1 ; IP address of xx_Bridge.py fromDMRPort = 31100 ; AMBE frames from xx_Bridge (should match "toGatewayPort" in xx_Bridge.cfg) toDMRPort = 31103 ; AMBE frames from xx_Bridge (should match "fromGatewayPort" in xx_Bridge.cfg) ambeMode = DMR ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW minTxTimeMS = 2000 ; Minimum time in MS for hang delay gatewayDmrId = 310502480 ; ID to use when transmitting from Analog_Bridge repeaterID = 310502480 ; ID of source repeater txTg = 31055 ; TG to use for all frames received from Analog_Bridge -> xx_Bridge txTs = 2 ; Slot to use for frames received from Analog_Bridge -> xx_Bridge colorCode = 1 ; Color Code to assign DMR frames ; Information for USRP channel driver. This interface uses PCM to transfer audio information ; There are two typical configurations, ASL and Transcode. ASL (AllstarLink) is for analog clients connected ; to a digital network. Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, ; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture. ; When using ASL, this matches the rpt.conf ASL file with a setting like: ; rxchannel = usrp/127.0.0.1:34001:32001 ; When Transcoding, make toASLPort equal to the other instance fromASLPort (crossover) [USRP] server = 127.0.0.1 ; IP address of Allstar/Asterisk toASLPort = 32001 ; Analog_Bridge <-- ASL fromASLPort = 34001 ; Analog_Bridge --> ASL aslAudio = AUDIO_UNITY ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) agcGain = -10 ; Gain (in db) of the AGC filter dmrAudio = AUDIO_UNITY ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) dmrGain = 0.25 ; Gain factor of audio from ASL (0.0-1.0) ; Information for DV3000 hardware decoder ; There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware) ; Use top server and port if using AMBEServer ; Use bottom server/port and serial = true if using the DV3000u (thumbdv) ; Did you run AMBETest4.py before using this? [DV3000] server = 127.0.0.1 ; IP address of AMBEServer port = 2460 ; Port of AMBEServer ; server = /dev/ttyUSB0 ; Device of DV3000U on this machine ; port = 460800 ; Baud rate of the dongle ; serial = true ; Use serial (DV3000U) or IP [General] Callsign=KC5MMW Id=310502480 Timeout=180 Duplex=0 ModeHang=0 RFModeHang=0 NetModeHang=0 Display=None Daemon=0 [Info] RXFrequency=222340000 TXFrequency=224940000 Power=1 Latitude=41.7333 Longitude=-50.3999 Height=0 Location=Iceberg, North Atlantic Description=MMDVM_Bridge URL=https://groups.io/g/DVSwitch [Log] # Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal DisplayLevel=1 FileLevel=2 FilePath=/var/log/mmdvm FileRoot=MMDVM_Bridge [DMR Id Lookup] File=/var/lib/mmdvm/DMRIds.dat Time=24 [NXDN Id Lookup] File=/var/lib/mmdvm/NXDN.csv Time=24 [Modem] Port=/dev/null RSSIMappingFile=RSSI.dat Trace=0 Debug=0 [D-Star] Enable=0 Module=C SelfOnly=0 AckReply=1 AckTime=750 ErrorReply=1 RemoteGateway=0 ModeHang=0 [DMR] Enable=1 Beacons=0 BeaconInterval=60 BeaconDuration=3 ColorCode=1 SelfOnly=0 EmbeddedLCOnly=1 DumpTAData=0 CallHang=0 TXHang=0 ModeHang=0 [System Fusion] Enable=0 LowDeviation=0 SelfOnly=0 RemoteGateway=0 ModeHang=0 [P25] Enable=0 NAC=293 SelfOnly=0 OverrideUIDCheck=0 RemoteGateway=0 ModeHang=0 [NXDN] Enable=0 RAN=1 SelfOnly=0 RemoteGateway=0 ModeHang=0 Id=12345 [D-Star Network] Enable=0 GatewayAddress=127.0.0.1 GatewayPort=20010 LocalPort=20011 ModeHang=0 Debug=0 [DMR Network] Enable=1 Address=3103.repeater.net Port=62031 Jitter=750 Local=62032 Password=passw0rd Slot1=1 Slot2=1 ModeHang=0 Debug=0 [System Fusion Network] Enable=0 LocalAddress=0 LocalPort=3200 GatewayAddress=127.0.0.1 GatewayPort=42000 ModeHang=0 Debug=0 [P25 Network] Enable=0 GatewayAddress=127.0.0.1 GatewayPort=42020 LocalPort=32010 ModeHang=0 Debug=0 [NXDN Network] Enable=0 #LocalAddress=127.0.0.1 ModeHang=0 Debug=0 LocalPort=14021 GatewayAddress=127.0.0.1 GatewayPort=14020
More All Messages By This Member
Re: Rpi3 Bridge Steve N4IRS #1422 That is a leftover from a older version and will be removed. It is done by ASL during install. Steve toggle quoted messageShow quoted text On 5/31/2018 7:54 AM, kc5mmw@... wrote: Could someone elaborate on the line in Analog_Bridge.ini that says "for RPI, don"t forget to modprobe sns_pcm_oss to get the devices populated" How do I do this?
More All Messages By This Member
Rpi3 Bridge Justin Morris #1421 Could someone elaborate on the line in Analog_Bridge.ini that says "for RPI, don"t forget to modprobe sns_pcm_oss to get the devices populated" How do I do this?
More All Messages By This Member
Re: DMR to AllStar Bridge - Private Call to DMR ID without a TG? Lito - WI6Y #1420 Hi Corey, This is the excerpt: Address=3103.repeater.net Port=62031 Jitter=750 Local=62032 Password=passw0rd As you can see, it is passw0rd. It does connect for a bit but then it disconnects and generates that message. toggle quoted messageShow quoted text From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of Corey Dean N3FE <n3fe@...> Sent: Wednesday, May 30, 2018 2:42 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? You have the wrong password in the config for connecting to the master. It should be passw0rd On May 30, 2018, at 4:26 PM, Roselito de los Reyes <Tolitski@...> wrote: Hi Steve, I am getting these messages from my MMDVM_bridge log. M: 2018-05-30 20:17:45.579 DMR, TX state = ON I: 2018-05-30 20:17:45.579 DMR, Begin TX: src=1107374 rpt=110737480 dst=5152 slot=2 cc=1 metadata=WI6Y M: 2018-05-30 20:17:47.601 DMR, TX state = OFF M: 2018-05-30 20:18:01.693 DMR Slot 2, received network voice header from KQ6RC to TG 5152 M: 2018-05-30 20:18:02.468 DMR Talker Alias (Data Format 1, Received 6/6 char): 'KQ6RC ' M: 2018-05-30 20:18:07.986 DMR Slot 2, received network end of voice transmission, 6.3 seconds, 0% packet loss, BER: 0.0% W: 2018-05-30 20:18:17.332 DMR, Login to the master has failed, retrying login ... E: 2018-05-30 20:19:17.332 DMR, Connection to the master has timed out, retrying connection M: 2018-05-30 20:19:17.332 DMR, Closing DMR Network M: 2018-05-30 20:19:17.332 DMR, Opening DMR Network D: 2018-05-30 20:19:27.337 DMR, Sending authorisation D: 2018-05-30 20:19:27.342 DMR, Sending configuration M: 2018-05-30 20:19:27.347 DMR, Logged into the master successfully M: 2018-05-30 20:19:32.315 DMR Slot 2, received network voice header from AF6YU to TG 5152 Why am I getting these messages ? Am I doing something wrong? or is 3103 just congested? Also, I noticed that sometimes the TA coming from YSF->DMR Mike's call sign (N4IRR) would come up as the default ID.. Where is that located in the config file? Thanks Lito From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of WillieB <will@...> Sent: Friday, May 25, 2018 5:15 PM To: main@dvswitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? Hi Steve, no problem. The only difference was the MMDVM_Bridge.ini had 3113756 instead of 311375690. I tried that just now and I could hear myself on hoseline, so I knew that part was working. So I tried from my radio as a private call and no luck. But then I changed it to a group call and BAM! Working perfectly. Now it even shows up under my Brandmeister self care as a new hotspot 311375690, so I can have separate static TGs than my ZUMspot. Thanks so much for your help Steve and Jeff, and others that replied. Have a great long weekend! Will KE4IAJ On Fri, May 25, 2018 at 7:40 PM, Steve N4IRS <szingman@...> wrote: Will, I tested the config below, but only from ASL to DMR. I do not have 3112138 programmed in my radio. I used the BM last heard and hoseline to verify audio. Can you show me your config in the same format? MMDVM_Bridge.ini [General] Callsign=N4IRS Id=311213890 Analog_Bridge.ini gatewayDmrId = 3112138 repeaterID = 311213890 txTg = 3112138 txTs = 2 colorCode = 1 On 05/25/2018 07:21 PM, WillieB wrote: Dell PowerEdge C1100 Virtual Machine on ESXi 5.1 Fresh install of Debian 9.4 (no GUI) 4 cores 4GB RAM 500GB HDD On Fri, May 25, 2018 at 7:09 PM, Steve N4IRS <szingman@...> wrote: Will, What hardware are you running the bridge on? On 05/25/2018 04:56 PM, WillieB wrote: Well I’m using a ZUMspot connecting through Brandmeister I think, so yes… From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Jeff Carrier Sent: Friday, May 25, 2018 4:55 PM To: main@dvswitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? If you're not connecting to brandmeister then it really doesn't matter I guess. I assumed you were intending to connect there. I didn't mean to throw a wrench in the conversation. On Fri, May 25, 2018 at 2:48 PM, WillieB <will@...> wrote: Steve => I tried that and I also tried the gatewayDmrId as the repeaterID just for grins. Neither worked. I don’t seem to be getting anywhere, but I greatly appreciate the time you guys have been taking to reply. Maybe I need to read some more about TGs. See further explanation below if there’s any confusion on what exactly I’m trying to accomplish. Jeff => Hmm, I’m not sure why I would need a repeater ID just for a DVswitch bridge? If I use a TG in txTg then it works fine. It just won’t allow me to specify a DMR ID in the txTg field. I’ll explain a bit further. The whole reason I’m trying to do this is to allow my HT to make a private or group call to the DMR ID used on the DVswitch bridge and be connected to my AllStar node. Then I can connect my bridged AllStar node to any other AllStar or Echolink node while using my ZUMspot as a DMR hotspot. So this allows me to have DMR, Echolink, and AllStar functionality using 1 hotspot. This works great when I use a TG, the only problem is I’m transmitting on the TG and the communication is only between my HT and the connected AllStar node. Let me give an example. On Tuesday nights at 8:00pm there’s an AllStar Technical net (DMR is discussed frequently) I want to connect to on AllStar node 45221. So what I would do is use my AllStar bridge node 46690 and connect it to 45221. So at that point when the net is taking place on 45221 I will be able to hear it and transmit to it on my HT via DMR ID 3113756. This works great when I bridge my AllStar node 46690 to our local talkgroup, but the only problem is I don’t want it to occupy the talk group. This is why I’m trying to setup a bridge to my DMR ID 3113756 that’s on my HT instead of using a TG. Maybe that clears things up if there is any confusion on what I’m trying to accomplish. If it’s not possible with DVswitch then maybe there are some kind of unused or private TGs I can use if I can’t get DMR IDs to work? Or maybe create my own TG? Guess I need to read more on how TGs work. From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Jeff Carrier Sent: Friday, May 25, 2018 3:37 PM To: main@dvswitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? DMR Repeater ID's are typically 6 digits long and they identify the repeater and can therefore be used as a talkgroup A DMR user ID is 7 digits and must be unique as it "generally" translates to an IP address in the DMR system. If you have not already requested a DMR repeater ID I'm thinking you'd need to do that. my 2 cents On Fri, May 25, 2018 at 1:30 PM, WillieB <will@...> wrote: Right, I understand those definitions. I set it up like this: gatewayDmrId = 3110229 <= DMR ID for KE4IAJ (ID that shows on all DMR radios when the direct is AllStar => DMR.) repeaterID = 311022901 <= DMR ID above + 01 txTg = 3113756 <= DMR ID for KE4IAJ In a reply from in this same thread you stated “My point is that you can use DMRID as a TG. I do it all the time for testing.”. Wouldn’t this mean that I can use a DMR ID for the txTg? If not then how can I use a DMR ID as a TG? From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 3:21 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? gatewayDmrId is the ID that ALL analog stations will present to BrandMeister it should be a user ID (7 digits) repeaterID is the repeater that BM thinks the analog traffic is coming from. txTg is the Talk Group that a analog user will transmit on. Steve On 5/25/2018 3:16 PM, WillieB wrote: Well I tested a private call, my DMR ID to a friend’s DMR ID, both of us with an HT behind a hotspot and it worked perfect. I could call him and he could call me. Then I tested some more with my bridge using 3113756 for both the gatewayDmrId and for txTg. It didn’t work in either direction. I could PTT on my HT and not hear anything on AllStar, and I could transmit on AllStar and not hear anything on my HT. In the meantime I received my other new DMR ID so I tested with it as well. See settings below for Analog_Bridge.ini, but unfortunately nothing is working, same results. 3110229 is my new ID and 311356 is my older one. I’m I setting this up correctly? If I set the contact to TG9 like Steve suggested then how do I specify to call my other DMR ID? I’m quite confused still on how to set this up as a bridge from my ASL node to my HT. Are there any kind of pseudo talkgroups or something similar? Any other ideas? gatewayDmrId = 3110229 ; ID to use when transmitting from Analog_Bridge repeaterID = 311022901 ; ID of source repeater txTg = 3113756 ; TG to use for all frames received from Analog_Bridge -> xx_Bridge From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of WillieB Sent: Friday, May 25, 2018 1:13 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? It doesn’t matter to me if it’s a group or private call. I’ll play around with different settings and see what works. From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 12:13 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? Hmmm, A private call? Interesting idea. Then maybe put the TG back to 9? I'll have to think/play with this idea... On 5/25/2018 11:42 AM, WillieB wrote: It’s working fine with a TG, but doesn’t seem to be working by me changing the txTg field to my 3113756 DMR ID and rebooting the bridge. I’m sure I’m just doing something wrong. As a test on my HT I did a manual private call to 3113756 and I don’t hear anything on the AllStar node. And when I key the AllStar node nothing happens on my HT. When I look in Brandmeister self-care, it’s showing an Auto Static group of 3113756 which I believe is correct. I’ve attached logs to the email which may help. I’m open for suggestions. 73 Will, KE4IAJ TARG AEC From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 9:28 AM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? You should be able to put your current DMRID in, you wont need a second ID. On 5/25/2018 9:25 AM, WillieB wrote: Thanks Steve, I’ve always argued the point to my teachers is that it depends on what definition of “sound” that you use lol. I have requested an additional DMR ID waiting for approval. Once it is approved I’ll test using it. My guess is that I just put the DMR ID in the txTg field in place of the TG in the Analog_Bridge.ini file. If that doesn’t work I’ll wait on the example documentation for the HBlink. Will From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 9:00 AM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? Will, A couple of comments here. Tying up a TG is a relative thing. Almost like if a tree falls in a forest and there is no one there to hear it, does it make a sound. My point is that you can use DMRID as a TG. I do it all the time for testing. Another way to solve the issue is to setup hblink as a server or master. Point your MMDVM_bridge at it and point you HS at it. You now have a private connection between MMDVM_Bridge and your ZUMspot. We are working on the documentation now and a example of that type of config is planned. HBlink is pretty easy to setup. Steve On 5/25/2018 8:47 AM, WillieB wrote: Hello group, I have searched and haven’t found anything so hopefully you guys can point me in the right direction. First of all many many thanks to Steve and anyone else involved for these programs and applications! I am using dvswitch with analog_bridge, mmdvm_bridge, and md380-emu to create a DMR to AllStar bridge. I have it working (Many thanks to KV4S (Russell)) fine bridging to a DMR talkgroup. My question is, can I bridge an AllStar node directly to a DMR user ID without a talkgroup? I guess this would be a private call? What I’m trying to accomplish here is to allow me to use my ZUMspot to connect to AllStar nodes through the bridge, but without tying up an entire talkgroup. Thanks in advance. 73 Will, KE4IAJ TARG AEC
More All Messages By This Member
Re: DMR to AllStar Bridge - Private Call to DMR ID without a TG? Corey Dean N3FE <n3fe@...> #1419 You have the wrong password in the config for connecting to the master. It should be passw0rd toggle quoted messageShow quoted text On May 30, 2018, at 4:26 PM, Roselito de los Reyes <Tolitski@...> wrote: Hi Steve, I am getting these messages from my MMDVM_bridge log. M: 2018-05-30 20:17:45.579 DMR, TX state = ON I: 2018-05-30 20:17:45.579 DMR, Begin TX: src=1107374 rpt=110737480 dst=5152 slot=2 cc=1 metadata=WI6Y M: 2018-05-30 20:17:47.601 DMR, TX state = OFF M: 2018-05-30 20:18:01.693 DMR Slot 2, received network voice header from KQ6RC to TG 5152 M: 2018-05-30 20:18:02.468 DMR Talker Alias (Data Format 1, Received 6/6 char): 'KQ6RC ' M: 2018-05-30 20:18:07.986 DMR Slot 2, received network end of voice transmission, 6.3 seconds, 0% packet loss, BER: 0.0% W: 2018-05-30 20:18:17.332 DMR, Login to the master has failed, retrying login ... E: 2018-05-30 20:19:17.332 DMR, Connection to the master has timed out, retrying connection M: 2018-05-30 20:19:17.332 DMR, Closing DMR Network M: 2018-05-30 20:19:17.332 DMR, Opening DMR Network D: 2018-05-30 20:19:27.337 DMR, Sending authorisation D: 2018-05-30 20:19:27.342 DMR, Sending configuration M: 2018-05-30 20:19:27.347 DMR, Logged into the master successfully M: 2018-05-30 20:19:32.315 DMR Slot 2, received network voice header from AF6YU to TG 5152 Why am I getting these messages ? Am I doing something wrong? or is 3103 just congested? Also, I noticed that sometimes the TA coming from YSF->DMR Mike's call sign (N4IRR) would come up as the default ID.. Where is that located in the config file? Thanks Lito From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of WillieB <will@...> Sent: Friday, May 25, 2018 5:15 PM To: main@dvswitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? Hi Steve, no problem. The only difference was the MMDVM_Bridge.ini had 3113756 instead of 311375690. I tried that just now and I could hear myself on hoseline, so I knew that part was working. So I tried from my radio as a private call and no luck. But then I changed it to a group call and BAM! Working perfectly. Now it even shows up under my Brandmeister self care as a new hotspot 311375690, so I can have separate static TGs than my ZUMspot. Thanks so much for your help Steve and Jeff, and others that replied. Have a great long weekend! Will KE4IAJ On Fri, May 25, 2018 at 7:40 PM, Steve N4IRS <szingman@...> wrote: Will, I tested the config below, but only from ASL to DMR. I do not have 3112138 programmed in my radio. I used the BM last heard and hoseline to verify audio. Can you show me your config in the same format? MMDVM_Bridge.ini [General] Callsign=N4IRS Id=311213890 Analog_Bridge.ini gatewayDmrId = 3112138 repeaterID = 311213890 txTg = 3112138 txTs = 2 colorCode = 1 On 05/25/2018 07:21 PM, WillieB wrote: Dell PowerEdge C1100 Virtual Machine on ESXi 5.1 Fresh install of Debian 9.4 (no GUI) 4 cores 4GB RAM 500GB HDD On Fri, May 25, 2018 at 7:09 PM, Steve N4IRS <szingman@...> wrote: Will, What hardware are you running the bridge on? On 05/25/2018 04:56 PM, WillieB wrote: Well I’m using a ZUMspot connecting through Brandmeister I think, so yes… From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Jeff Carrier Sent: Friday, May 25, 2018 4:55 PM To: main@dvswitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? If you're not connecting to brandmeister then it really doesn't matter I guess. I assumed you were intending to connect there. I didn't mean to throw a wrench in the conversation. On Fri, May 25, 2018 at 2:48 PM, WillieB <will@...> wrote: Steve => I tried that and I also tried the gatewayDmrId as the repeaterID just for grins. Neither worked. I don’t seem to be getting anywhere, but I greatly appreciate the time you guys have been taking to reply. Maybe I need to read some more about TGs. See further explanation below if there’s any confusion on what exactly I’m trying to accomplish. Jeff => Hmm, I’m not sure why I would need a repeater ID just for a DVswitch bridge? If I use a TG in txTg then it works fine. It just won’t allow me to specify a DMR ID in the txTg field. I’ll explain a bit further. The whole reason I’m trying to do this is to allow my HT to make a private or group call to the DMR ID used on the DVswitch bridge and be connected to my AllStar node. Then I can connect my bridged AllStar node to any other AllStar or Echolink node while using my ZUMspot as a DMR hotspot. So this allows me to have DMR, Echolink, and AllStar functionality using 1 hotspot. This works great when I use a TG, the only problem is I’m transmitting on the TG and the communication is only between my HT and the connected AllStar node. Let me give an example. On Tuesday nights at 8:00pm there’s an AllStar Technical net (DMR is discussed frequently) I want to connect to on AllStar node 45221. So what I would do is use my AllStar bridge node 46690 and connect it to 45221. So at that point when the net is taking place on 45221 I will be able to hear it and transmit to it on my HT via DMR ID 3113756. This works great when I bridge my AllStar node 46690 to our local talkgroup, but the only problem is I don’t want it to occupy the talk group. This is why I’m trying to setup a bridge to my DMR ID 3113756 that’s on my HT instead of using a TG. Maybe that clears things up if there is any confusion on what I’m trying to accomplish. If it’s not possible with DVswitch then maybe there are some kind of unused or private TGs I can use if I can’t get DMR IDs to work? Or maybe create my own TG? Guess I need to read more on how TGs work. From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Jeff Carrier Sent: Friday, May 25, 2018 3:37 PM To: main@dvswitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? DMR Repeater ID's are typically 6 digits long and they identify the repeater and can therefore be used as a talkgroup A DMR user ID is 7 digits and must be unique as it "generally" translates to an IP address in the DMR system. If you have not already requested a DMR repeater ID I'm thinking you'd need to do that. my 2 cents On Fri, May 25, 2018 at 1:30 PM, WillieB <will@...> wrote: Right, I understand those definitions. I set it up like this: gatewayDmrId = 3110229 <= DMR ID for KE4IAJ (ID that shows on all DMR radios when the direct is AllStar => DMR.) repeaterID = 311022901 <= DMR ID above + 01 txTg = 3113756 <= DMR ID for KE4IAJ In a reply from in this same thread you stated “My point is that you can use DMRID as a TG. I do it all the time for testing.”. Wouldn’t this mean that I can use a DMR ID for the txTg? If not then how can I use a DMR ID as a TG? From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 3:21 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? gatewayDmrId is the ID that ALL analog stations will present to BrandMeister it should be a user ID (7 digits) repeaterID is the repeater that BM thinks the analog traffic is coming from. txTg is the Talk Group that a analog user will transmit on. Steve On 5/25/2018 3:16 PM, WillieB wrote: Well I tested a private call, my DMR ID to a friend’s DMR ID, both of us with an HT behind a hotspot and it worked perfect. I could call him and he could call me. Then I tested some more with my bridge using 3113756 for both the gatewayDmrId and for txTg. It didn’t work in either direction. I could PTT on my HT and not hear anything on AllStar, and I could transmit on AllStar and not hear anything on my HT. In the meantime I received my other new DMR ID so I tested with it as well. See settings below for Analog_Bridge.ini, but unfortunately nothing is working, same results. 3110229 is my new ID and 311356 is my older one. I’m I setting this up correctly? If I set the contact to TG9 like Steve suggested then how do I specify to call my other DMR ID? I’m quite confused still on how to set this up as a bridge from my ASL node to my HT. Are there any kind of pseudo talkgroups or something similar? Any other ideas? gatewayDmrId = 3110229 ; ID to use when transmitting from Analog_Bridge repeaterID = 311022901 ; ID of source repeater txTg = 3113756 ; TG to use for all frames received from Analog_Bridge -> xx_Bridge From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of WillieB Sent: Friday, May 25, 2018 1:13 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? It doesn’t matter to me if it’s a group or private call. I’ll play around with different settings and see what works. From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 12:13 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? Hmmm, A private call? Interesting idea. Then maybe put the TG back to 9? I'll have to think/play with this idea... On 5/25/2018 11:42 AM, WillieB wrote: It’s working fine with a TG, but doesn’t seem to be working by me changing the txTg field to my 3113756 DMR ID and rebooting the bridge. I’m sure I’m just doing something wrong. As a test on my HT I did a manual private call to 3113756 and I don’t hear anything on the AllStar node. And when I key the AllStar node nothing happens on my HT. When I look in Brandmeister self-care, it’s showing an Auto Static group of 3113756 which I believe is correct. I’ve attached logs to the email which may help. I’m open for suggestions. 73 Will, KE4IAJ TARG AEC From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 9:28 AM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? You should be able to put your current DMRID in, you wont need a second ID. On 5/25/2018 9:25 AM, WillieB wrote: Thanks Steve, I’ve always argued the point to my teachers is that it depends on what definition of “sound” that you use lol. I have requested an additional DMR ID waiting for approval. Once it is approved I’ll test using it. My guess is that I just put the DMR ID in the txTg field in place of the TG in the Analog_Bridge.ini file. If that doesn’t work I’ll wait on the example documentation for the HBlink. Will From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 9:00 AM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? Will, A couple of comments here. Tying up a TG is a relative thing. Almost like if a tree falls in a forest and there is no one there to hear it, does it make a sound. My point is that you can use DMRID as a TG. I do it all the time for testing. Another way to solve the issue is to setup hblink as a server or master. Point your MMDVM_bridge at it and point you HS at it. You now have a private connection between MMDVM_Bridge and your ZUMspot. We are working on the documentation now and a example of that type of config is planned. HBlink is pretty easy to setup. Steve On 5/25/2018 8:47 AM, WillieB wrote: Hello group, I have searched and haven’t found anything so hopefully you guys can point me in the right direction. First of all many many thanks to Steve and anyone else involved for these programs and applications! I am using dvswitch with analog_bridge, mmdvm_bridge, and md380-emu to create a DMR to AllStar bridge. I have it working (Many thanks to KV4S (Russell)) fine bridging to a DMR talkgroup. My question is, can I bridge an AllStar node directly to a DMR user ID without a talkgroup? I guess this would be a private call? What I’m trying to accomplish here is to allow me to use my ZUMspot to connect to AllStar nodes through the bridge, but without tying up an entire talkgroup. Thanks in advance. 73 Will, KE4IAJ TARG AEC
More All Messages By This Member
Re: DMR to AllStar Bridge - Private Call to DMR ID without a TG? Lito - WI6Y #1418 Hi Steve, I am getting these messages from my MMDVM_bridge log. M: 2018-05-30 20:17:45.579 DMR, TX state = ON I: 2018-05-30 20:17:45.579 DMR, Begin TX: src=1107374 rpt=110737480 dst=5152 slot=2 cc=1 metadata=WI6Y M: 2018-05-30 20:17:47.601 DMR, TX state = OFF M: 2018-05-30 20:18:01.693 DMR Slot 2, received network voice header from KQ6RC to TG 5152 M: 2018-05-30 20:18:02.468 DMR Talker Alias (Data Format 1, Received 6/6 char): 'KQ6RC ' M: 2018-05-30 20:18:07.986 DMR Slot 2, received network end of voice transmission, 6.3 seconds, 0% packet loss, BER: 0.0% W: 2018-05-30 20:18:17.332 DMR, Login to the master has failed, retrying login ... E: 2018-05-30 20:19:17.332 DMR, Connection to the master has timed out, retrying connection M: 2018-05-30 20:19:17.332 DMR, Closing DMR Network M: 2018-05-30 20:19:17.332 DMR, Opening DMR Network D: 2018-05-30 20:19:27.337 DMR, Sending authorisation D: 2018-05-30 20:19:27.342 DMR, Sending configuration M: 2018-05-30 20:19:27.347 DMR, Logged into the master successfully M: 2018-05-30 20:19:32.315 DMR Slot 2, received network voice header from AF6YU to TG 5152 Why am I getting these messages ? Am I doing something wrong? or is 3103 just congested? Also, I noticed that sometimes the TA coming from YSF->DMR Mike's call sign (N4IRR) would come up as the default ID.. Where is that located in the config file? Thanks Lito toggle quoted messageShow quoted text From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of WillieB <will@...> Sent: Friday, May 25, 2018 5:15 PM To: main@dvswitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? Hi Steve, no problem. The only difference was the MMDVM_Bridge.ini had 3113756 instead of 311375690. I tried that just now and I could hear myself on hoseline, so I knew that part was working. So I tried from my radio as a private call and no luck. But then I changed it to a group call and BAM! Working perfectly. Now it even shows up under my Brandmeister self care as a new hotspot 311375690, so I can have separate static TGs than my ZUMspot. Thanks so much for your help Steve and Jeff, and others that replied. Have a great long weekend! Will KE4IAJ On Fri, May 25, 2018 at 7:40 PM, Steve N4IRS <szingman@...> wrote: Will, I tested the config below, but only from ASL to DMR. I do not have 3112138 programmed in my radio. I used the BM last heard and hoseline to verify audio. Can you show me your config in the same format? MMDVM_Bridge.ini [General] Callsign=N4IRS Id=311213890 Analog_Bridge.ini gatewayDmrId = 3112138 repeaterID = 311213890 txTg = 3112138 txTs = 2 colorCode = 1 On 05/25/2018 07:21 PM, WillieB wrote: Dell PowerEdge C1100 Virtual Machine on ESXi 5.1 Fresh install of Debian 9.4 (no GUI) 4 cores 4GB RAM 500GB HDD On Fri, May 25, 2018 at 7:09 PM, Steve N4IRS <szingman@...> wrote: Will, What hardware are you running the bridge on? On 05/25/2018 04:56 PM, WillieB wrote: Well I’m using a ZUMspot connecting through Brandmeister I think, so yes… From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Jeff Carrier Sent: Friday, May 25, 2018 4:55 PM To: main@dvswitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? If you're not connecting to brandmeister then it really doesn't matter I guess. I assumed you were intending to connect there. I didn't mean to throw a wrench in the conversation. On Fri, May 25, 2018 at 2:48 PM, WillieB <will@...> wrote: Steve => I tried that and I also tried the gatewayDmrId as the repeaterID just for grins. Neither worked. I don’t seem to be getting anywhere, but I greatly appreciate the time you guys have been taking to reply. Maybe I need to read some more about TGs. See further explanation below if there’s any confusion on what exactly I’m trying to accomplish. Jeff => Hmm, I’m not sure why I would need a repeater ID just for a DVswitch bridge? If I use a TG in txTg then it works fine. It just won’t allow me to specify a DMR ID in the txTg field. I’ll explain a bit further. The whole reason I’m trying to do this is to allow my HT to make a private or group call to the DMR ID used on the DVswitch bridge and be connected to my AllStar node. Then I can connect my bridged AllStar node to any other AllStar or Echolink node while using my ZUMspot as a DMR hotspot. So this allows me to have DMR, Echolink, and AllStar functionality using 1 hotspot. This works great when I use a TG, the only problem is I’m transmitting on the TG and the communication is only between my HT and the connected AllStar node. Let me give an example. On Tuesday nights at 8:00pm there’s an AllStar Technical net (DMR is discussed frequently) I want to connect to on AllStar node 45221. So what I would do is use my AllStar bridge node 46690 and connect it to 45221. So at that point when the net is taking place on 45221 I will be able to hear it and transmit to it on my HT via DMR ID 3113756. This works great when I bridge my AllStar node 46690 to our local talkgroup, but the only problem is I don’t want it to occupy the talk group. This is why I’m trying to setup a bridge to my DMR ID 3113756 that’s on my HT instead of using a TG. Maybe that clears things up if there is any confusion on what I’m trying to accomplish. If it’s not possible with DVswitch then maybe there are some kind of unused or private TGs I can use if I can’t get DMR IDs to work? Or maybe create my own TG? Guess I need to read more on how TGs work. From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Jeff Carrier Sent: Friday, May 25, 2018 3:37 PM To: main@dvswitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? DMR Repeater ID's are typically 6 digits long and they identify the repeater and can therefore be used as a talkgroup A DMR user ID is 7 digits and must be unique as it "generally" translates to an IP address in the DMR system. If you have not already requested a DMR repeater ID I'm thinking you'd need to do that. my 2 cents On Fri, May 25, 2018 at 1:30 PM, WillieB <will@...> wrote: Right, I understand those definitions. I set it up like this: gatewayDmrId = 3110229 <= DMR ID for KE4IAJ (ID that shows on all DMR radios when the direct is AllStar => DMR.) repeaterID = 311022901 <= DMR ID above + 01 txTg = 3113756 <= DMR ID for KE4IAJ In a reply from in this same thread you stated “My point is that you can use DMRID as a TG. I do it all the time for testing.”. Wouldn’t this mean that I can use a DMR ID for the txTg? If not then how can I use a DMR ID as a TG? From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 3:21 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? gatewayDmrId is the ID that ALL analog stations will present to BrandMeister it should be a user ID (7 digits) repeaterID is the repeater that BM thinks the analog traffic is coming from. txTg is the Talk Group that a analog user will transmit on. Steve On 5/25/2018 3:16 PM, WillieB wrote: Well I tested a private call, my DMR ID to a friend’s DMR ID, both of us with an HT behind a hotspot and it worked perfect. I could call him and he could call me. Then I tested some more with my bridge using 3113756 for both the gatewayDmrId and for txTg. It didn’t work in either direction. I could PTT on my HT and not hear anything on AllStar, and I could transmit on AllStar and not hear anything on my HT. In the meantime I received my other new DMR ID so I tested with it as well. See settings below for Analog_Bridge.ini, but unfortunately nothing is working, same results. 3110229 is my new ID and 311356 is my older one. I’m I setting this up correctly? If I set the contact to TG9 like Steve suggested then how do I specify to call my other DMR ID? I’m quite confused still on how to set this up as a bridge from my ASL node to my HT. Are there any kind of pseudo talkgroups or something similar? Any other ideas? gatewayDmrId = 3110229 ; ID to use when transmitting from Analog_Bridge repeaterID = 311022901 ; ID of source repeater txTg = 3113756 ; TG to use for all frames received from Analog_Bridge -> xx_Bridge From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of WillieB Sent: Friday, May 25, 2018 1:13 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? It doesn’t matter to me if it’s a group or private call. I’ll play around with different settings and see what works. From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 12:13 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? Hmmm, A private call? Interesting idea. Then maybe put the TG back to 9? I'll have to think/play with this idea... On 5/25/2018 11:42 AM, WillieB wrote: It’s working fine with a TG, but doesn’t seem to be working by me changing the txTg field to my 3113756 DMR ID and rebooting the bridge. I’m sure I’m just doing something wrong. As a test on my HT I did a manual private call to 3113756 and I don’t hear anything on the AllStar node. And when I key the AllStar node nothing happens on my HT. When I look in Brandmeister self-care, it’s showing an Auto Static group of 3113756 which I believe is correct. I’ve attached logs to the email which may help. I’m open for suggestions. 73 Will, KE4IAJ TARG AEC From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 9:28 AM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? You should be able to put your current DMRID in, you wont need a second ID. On 5/25/2018 9:25 AM, WillieB wrote: Thanks Steve, I’ve always argued the point to my teachers is that it depends on what definition of “sound” that you use lol. I have requested an additional DMR ID waiting for approval. Once it is approved I’ll test using it. My guess is that I just put the DMR ID in the txTg field in place of the TG in the Analog_Bridge.ini file. If that doesn’t work I’ll wait on the example documentation for the HBlink. Will From: main@DVSwitch.groups.io [mailto:main@...o] On Behalf Of Steve N4IRS Sent: Friday, May 25, 2018 9:00 AM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] DMR to AllStar Bridge - Private Call to DMR ID without a TG? Will, A couple of comments here. Tying up a TG is a relative thing. Almost like if a tree falls in a forest and there is no one there to hear it, does it make a sound. My point is that you can use DMRID as a TG. I do it all the time for testing. Another way to solve the issue is to setup hblink as a server or master. Point your MMDVM_bridge at it and point you HS at it. You now have a private connection between MMDVM_Bridge and your ZUMspot. We are working on the documentation now and a example of that type of config is planned. HBlink is pretty easy to setup. Steve On 5/25/2018 8:47 AM, WillieB wrote: Hello group, I have searched and haven’t found anything so hopefully you guys can point me in the right direction. First of all many many thanks to Steve and anyone else involved for these programs and applications! I am using dvswitch with analog_bridge, mmdvm_bridge, and md380-emu to create a DMR to AllStar bridge. I have it working (Many thanks to KV4S (Russell)) fine bridging to a DMR talkgroup. My question is, can I bridge an AllStar node directly to a DMR user ID without a talkgroup? I guess this would be a private call? What I’m trying to accomplish here is to allow me to use my ZUMspot to connect to AllStar nodes through the bridge, but without tying up an entire talkgroup. Thanks in advance. 73 Will, KE4IAJ TARG AEC
More All Messages By This Member
Re: Updated DVSwitch repository available WillieB <will@...> #1417 I tuned my audio last night and ended up with the settings below. First I connected the my bridged node to a local repeater node and equalized the audio listening on DMR and Analog. Once the DMR receive audio was adjusted I then connected my bridged node to 3009999 (Echolink Test Server) and adjusted the audio coming back. Not a perfect science but audio sounds really good in both directions now. aslAudio = AUDIO_USE_AGC agcGain = -10 dmrAudio = AUDIO_USE_GAIN dmrGain = 0.50 73 Will, KE4IAJ TARG AEC toggle quoted messageShow quoted text From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS Sent: Wednesday, May 30, 2018 1:08 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] Updated DVSwitch repository available Peter, Use: dmrAudio = AUDIO_USE_GAIN ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) dmrGain = 2 ; Gain factor of audio from ASL (0.0-1.0) This is multiply by 2. If still too low raise by 1 until you get it where you want it. 3.5 is a acceptable number. Mike and I have been talking about tweaking these defaults. Steve On 5/30/2018 12:58 PM, Peter Buckley via Groups.Io wrote: Thanks Steve, Please make a suggestion as your schedule allows. Symptom needing help: low volume audio coming back in from DMR side to Allstar side. My current Analog_Bridge.ini is below. Original entries marked with a # (updated entries right below those lines) Steve - I made the adjustments based on an earlier email (to the group) from you. Q.) How best to include the DMR Audio going into the Allstar side. 73s -pete N0ECT [USRP] server = 127.0.0.1 ; IP address of Allstar/Asterisk toASLPort = 32001 ; Analog_Bridge <-- ASL fromASLPort = 34001 ; Analog_Bridge --> ASL # aslAudio = AUDIO_UNITY ; Original Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) aslAudio = AUDIO_USE_GAIN ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) # agcGain = -20 ; Original Gain (in db) of the AGC filter agcGain = .5 ; Gain (in db) of the AGC filter dmrAudio = AUDIO_UNITY ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) dmrGain = 0.65 ; Gain factor of audio from ASL (0.0-1.0) # dmrGain = 0.35 ; Original Gain factor of audio from ASL (0.0-1.0) On Sunday, May 20, 2018 7:23 PM, Steve N4IRS <szingman@...> wrote: I have some updates to make to to the programs, meta packages and config files. We are changing some of the defaults to point to the test reflectors. There are a few minor updates to the programs. Mike and I have been working on the documentation and example configs. I'll be updating the wiki with some of the samples. 73, Steve N4IRS
More All Messages By This Member
Re: DMR to ASL audio level Peter Buckley #1416 Thanks Steve, That DMR Audio increase tip - worked perfectly. The DMR side came up (what I needed) to get the analog listeners (Allstar) up to a good level. Our assigned BM/TG 31085 is connected to an old Analog Repeater system that covers most of western Colorado - Vail, Aspen, Glenwood Springs and Grand Junction. 73s pete N0ECT toggle quoted messageShow quoted text On Wednesday, May 30, 2018 11:07 AM, Steve N4IRS <szingman@...> wrote: Peter, Use: dmrAudio = AUDIO_USE_GAIN ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) dmrGain = 2 ; Gain factor of audio from ASL (0.0-1.0) This is multiply by 2. If still too low raise by 1 until you get it where you want it. 3.5 is a acceptable number. Mike and I have been talking about tweaking these defaults. Steve On 5/30/2018 12:58 PM, Peter Buckley via Groups.Io wrote: Thanks Steve, Please make a suggestion as your schedule allows. Symptom needing help: low volume audio coming back in from DMR side to Allstar side. My current Analog_Bridge.ini is below. Original entries marked with a # (updated entries right below those lines) Steve - I made the adjustments based on an earlier email (to the group) from you. Q.) How best to include the DMR Audio going into the Allstar side. 73s -pete N0ECT [USRP] server = 127.0.0.1 ; IP address of Allstar/Asterisk toASLPort = 32001 ; Analog_Bridge <-- ASL fromASLPort = 34001 ; Analog_Bridge --> ASL # aslAudio = AUDIO_UNITY ; Original Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) aslAudio = AUDIO_USE_GAIN ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) # agcGain = -20 ; Original Gain (in db) of the AGC filter agcGain = .5 ; Gain (in db) of the AGC filter dmrAudio = AUDIO_UNITY ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) dmrGain = 0.65 ; Gain factor of audio from ASL (0.0-1.0) # dmrGain = 0.35 ; Original Gain factor of audio from ASL (0.0-1.0) On Sunday, May 20, 2018 7:23 PM, Steve N4IRS <szingman@...> wrote: I have some updates to make to to the programs, meta packages and config files. We are changing some of the defaults to point to the test reflectors. There are a few minor updates to the programs. Mike and I have been working on the documentation and example configs. I'll be updating the wiki with some of the samples. 73, Steve N4IRS
More All Messages By This Member
Re: DMR to ASL audio level Steve N4IRS #1415 Peter, Use: dmrAudio = AUDIO_USE_GAIN ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) dmrGain = 2 ; Gain factor of audio from ASL (0.0-1.0) This is multiply by 2. If still too low raise by 1 until you get it where you want it. 3.5 is a acceptable number. Mike and I have been talking about tweaking these defaults. Steve toggle quoted messageShow quoted text On 5/30/2018 12:58 PM, Peter Buckley via Groups.Io wrote: Thanks Steve, Please make a suggestion as your schedule allows. Symptom needing help: low volume audio coming back in from DMR side to Allstar side. My current Analog_Bridge.ini is below. Original entries marked with a # (updated entries right below those lines) Steve - I made the adjustments based on an earlier email (to the group) from you. Q.) How best to include the DMR Audio going into the Allstar side. 73s -pete N0ECT [USRP] server = 127.0.0.1 ; IP address of Allstar/Asterisk toASLPort = 32001 ; Analog_Bridge <-- ASL fromASLPort = 34001 ; Analog_Bridge --> ASL # aslAudio = AUDIO_UNITY ; Original Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) aslAudio = AUDIO_USE_GAIN ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) # agcGain = -20 ; Original Gain (in db) of the AGC filter agcGain = .5 ; Gain (in db) of the AGC filter dmrAudio = AUDIO_UNITY ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) dmrGain = 0.65 ; Gain factor of audio from ASL (0.0-1.0) # dmrGain = 0.35 ; Original Gain factor of audio from ASL (0.0-1.0) On Sunday, May 20, 2018 7:23 PM, Steve N4IRS <szingman@...> wrote: I have some updates to make to to the programs, meta packages and config files. We are changing some of the defaults to point to the test reflectors. There are a few minor updates to the programs. Mike and I have been working on the documentation and example configs. I'll be updating the wiki with some of the samples. 73, Steve N4IRS
More All Messages By This Member
DMR to ASL audio level Peter Buckley #1414 Thanks Steve, Please make a suggestion as your schedule allows. Symptom needing help: low volume audio coming back in from DMR side to Allstar side. My current Analog_Bridge.ini is below. Original entries marked with a # (updated entries right below those lines) Steve - I made the adjustments based on an earlier email (to the group) from you. Q.) How best to include the DMR Audio going into the Allstar side. 73s -pete N0ECT [USRP] server = 127.0.0.1 ; IP address of Allstar/Asterisk toASLPort = 32001 ; Analog_Bridge <-- ASL fromASLPort = 34001 ; Analog_Bridge --> ASL # aslAudio = AUDIO_UNITY ; Original Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) aslAudio = AUDIO_USE_GAIN ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN) # agcGain = -20 ; Original Gain (in db) of the AGC filter agcGain = .5 ; Gain (in db) of the AGC filter dmrAudio = AUDIO_UNITY ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) dmrGain = 0.65 ; Gain factor of audio from ASL (0.0-1.0) # dmrGain = 0.35 ; Original Gain factor of audio from ASL (0.0-1.0) toggle quoted messageShow quoted text On Sunday, May 20, 2018 7:23 PM, Steve N4IRS <szingman@...> wrote: I have some updates to make to to the programs, meta packages and config files. We are changing some of the defaults to point to the test reflectors. There are a few minor updates to the programs. Mike and I have been working on the documentation and example configs. I'll be updating the wiki with some of the samples. 73, Steve N4IRS
More All Messages By This Member
Re: A brief how to, please Paul Nannery KC2VRJ #1413 I have a low cost vps cloud at cost. Not the best but works however my OS choice is very limited. toggle quoted messageShow quoted text On Wed, May 30, 2018, 12:37 PM Steve N4IRS <szingman@...> wrote: Happy to help. It allowed me to find and fix a issue. I'm building everything on Jessie for now so bith Jessie and Stretch are supported. Steve On 5/30/2018 12:35 PM, Paul Nannery KC2VRJ wrote: Steve, Thank you for your help it installed now to make it all play nice
More All Messages By This Member
Re: A brief how to, please Steve N4IRS #1412 Happy to help. It allowed me to find and fix a issue. I'm building everything on Jessie for now so bith Jessie and Stretch are supported. Steve toggle quoted messageShow quoted text On 5/30/2018 12:35 PM, Paul Nannery KC2VRJ wrote: Steve, Thank you for your help it installed now to make it all play nice
More All Messages By This Member
Re: A brief how to, please Paul Nannery KC2VRJ #1411 Steve, Thank you for your help it installed now to make it all play nice
More All Messages By This Member
Re: Updated DVSwitch repository available Steve N4IRS #1410 Mike, Analog_Bridge is one of the programs in the overall DVSwitch "family" We have enhanced Analog_Bridge and added MMDVM_Bridge, Quantar_Bridge and a few others. We are still early in testing and we are now using the Debian apt method to install. Mike and I have been working on documentation and examples. 73, Steve toggle quoted messageShow quoted text On 5/30/2018 10:11 AM, Mike Swiatkowski via Groups.Io wrote: Steve, I may have fallen behind with the announcement so my apologies. Is DVSwitch replacing Analog_Bridge from github since it also contains Analog_Bridge and has much more functionality? It looks like that is where most of yours and Mike's development efforts have been concentrated lately. I'm looking forward to trying it all out. Mike, AA9VI
More All Messages By This Member
Re: Updated DVSwitch repository available Mike, AA9VI #1409 Steve, I may have fallen behind with the announcement so my apologies. Is DVSwitch replacing Analog_Bridge from github since it also contains Analog_Bridge and has much more functionality? It looks like that is where most of yours and Mike's development efforts have been concentrated lately. I'm looking forward to trying it all out. Mike, AA9VI
More All Messages By This Member
Re: A brief how to, please Steve N4IRS #1408 Paul, Please do a apt-get update then apt-get install analog-bridge toggle quoted messageShow quoted text On 5/30/2018 7:13 AM, Paul Nannery KC2VRJ wrote: I am waiting on Debian to spin back up I had ubuntu running to see if that worked. on ubuntu 14.4 I now get The following packages have unmet dependencies: analog-bridge : Depends: libsound2 but it is not installable E: Unable to correct problems, you have held broken packages. ill try Debian 8 as soon as it finishes the install On Wed, May 30, 2018 at 7:01 AM, Steve N4IRS <szingman@...> wrote: Paul, Try a apt-get update then apt-get install analog-bridge I wont be able to test it on Jessie for about 2 hours. Let me know the results. Steve On 05/30/2018 06:34 AM, Paul Nannery KC2VRJ wrote: AMD 64 tried both debian 8 and ubuntu 14. My vps provider does not have debian 9 so I did not try that. On Wed, May 30, 2018, 6:32 AM Steve N4IRS <szingman@...> wrote: Paul, What hardware (arch) i386, amd64, armhf? uname -a 73, Steve N4IRS On 05/30/2018 03:16 AM, Paul Nannery KC2VRJ wrote: Guys, I am having this same issues on Jessie The following packages have unmet dependencies: analog-bridge : Depends: libsoundio-dev but it is not installable E: Unable to correct problems, you have held broken packages. any ideas? On Mon, May 14, 2018 at 7:42 PM, Steve N4IRS <szingman@...> wrote: your problem is fixed. apt-get update apt-get install analog-bridge All applications and config files are installed in /opt as in /opt/Analog_Bridge On 05/14/2018 07:19 PM, Michael Rickey (AF6FB) wrote: I'm having problems with this as well. The only place I've found that talks about installing anything is the post you mentioned. I'm able to get through the first part, when I run "apt-get install analog_bridge" I get the error "analog_bridge: Depends: libsoundio-dev but it is not installable". Also, what folder are the config files in? I'm running on Raspian Stretch Thanks in advance, Michael AF6FB
More All Messages By This Member
Re: A brief how to, please Santu OTTAVI (TK1BI) #1407 Hi, Le 30/05/2018 à 12:32, Steve N4IRS a écrit : What hardware (arch) i386, amd64, armhf? What about opening the source in a GitHub ? This would make things much easier ;-) 73 de TK1BI
More All Messages By This Member

7921 - 7940 of 9288

Home Messages Hashtags Subgroups Wiki About Features Pricing Updates Terms Help Twitter