Date   

Re: Bridging from MMDVM repeater to IPSC network

Rob WX1N
 

Ok, so it can tell what is connecting, similar to the Client/Package ID's? Is the difference in behavior between a DMRlink connection and a Motorola repeater connection specific to BM? What I'm getting at with that is, if I were to request and receive access to a c-Bridge, would it also behave differently for a DMRlink connection than it would for a Motorola repeater connection?

-----Original Message-----
From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of Steve N4IRS
Sent: Friday, June 23, 2017 12:05 PM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Bridging from MMDVM repeater to IPSC network

The connection from DMRlink to BM is as you say considered by BM as a SmartPTT connection. This does not happen on a connection from a Motorola Repeater. It's all about how BM treats a DMRLink connection.

On 6/23/2017 12:02 PM, Rob WX1N wrote:
Radio ID 313323, TS 1, TG 313324. Just to make sure I'm understanding this right - a valid IPSC connection to BM will pass absolutely nothing back and forth until it is preconfigured on the server end?

-----Original Message-----
From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of
Steve N4IRS
Sent: Friday, June 23, 2017 12:00 PM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Bridging from MMDVM repeater to IPSC network

Let me be a little more clear. The connection from DMRlink to BM is as you say considered by BM as a SmartPTT connection. For a BM SmartPTT connection, a BM admin (I am one) has to configure the bridge in BM. I will need the following:
Radio_ID: in dmrlink.cfg
The TS and TG you want to bridge.

This can NOT be configured from a self care account.

On 6/23/2017 11:58 AM, Rob WX1N wrote:
Steve,
In the DMR link configuration, I'm signing in to 3102 as the repeater
ID, which has several static TG's preconfigured. I'm transmitting
using my personal ID, on one of the static TG's (although if I were
using a different TG, wouldn't it bring it up as a dynamic for a few
minutes?)

-----Original Message-----
From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of
Steve N4IRS
Sent: Friday, June 23, 2017 11:55 AM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Bridging from MMDVM repeater to IPSC network

Rob,
Is 3102 setup to bridge the TG you are trying from the Radio ID you are presenting to BM?

On 6/23/2017 11:53 AM, Rob WX1N wrote:
Good morning,

I'm hoping for some basic info if one of you has the time to point me in the right direction. I know this is still a work in progress and I don't want to interfere with that, so if this isn't a quick answer, then please disregard.

I'm playing around with the new Bridge branches of HBlink and DMRlink. I wanted to see if I could successfully connect an MMDVM repeater to an IPSC network. I set it up as follows: MMDVM set to connect to local instance of HBlink (successful). HBlink configuration as a master to allow MMDVM to connect. Run MMDVMHost, run HB_Bridge.py. DMRlink configured as a peer to connect to the IPSC connection of 3102. Run IPSC_Bridge.py.
Results - MMDVM connects to HBlink and transmissions show in both HB_Bridge and IPSC_Bridge terminal windows, however, the transmissions don't seem to be making it through to the network. I think I am connected to 3102, as the repeater shows up in the 3102 status page (albeit as a SmartPTT network).

Does anyone have a guess as to where I'm going wrong?

Rob, WX1N












Re: Bridging from MMDVM repeater to IPSC network

Steve N4IRS
 

I have added Radio ID 313323 TS1 TG 313324 to bridge.json on BM server 3102.

On 6/23/2017 12:02 PM, Rob WX1N wrote:
Radio ID 313323, TS 1, TG 313324. Just to make sure I'm understanding this right - a valid IPSC connection to BM will pass absolutely nothing back and forth until it is preconfigured on the server end?

-----Original Message-----
From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of Steve N4IRS
Sent: Friday, June 23, 2017 12:00 PM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Bridging from MMDVM repeater to IPSC network

Let me be a little more clear. The connection from DMRlink to BM is as you say considered by BM as a SmartPTT connection. For a BM SmartPTT connection, a BM admin (I am one) has to configure the bridge in BM. I will need the following:
Radio_ID: in dmrlink.cfg
The TS and TG you want to bridge.

This can NOT be configured from a self care account.

On 6/23/2017 11:58 AM, Rob WX1N wrote:
Steve,
In the DMR link configuration, I'm signing in to 3102 as the repeater
ID, which has several static TG's preconfigured. I'm transmitting
using my personal ID, on one of the static TG's (although if I were
using a different TG, wouldn't it bring it up as a dynamic for a few
minutes?)

-----Original Message-----
From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of
Steve N4IRS
Sent: Friday, June 23, 2017 11:55 AM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Bridging from MMDVM repeater to IPSC network

Rob,
Is 3102 setup to bridge the TG you are trying from the Radio ID you are presenting to BM?

On 6/23/2017 11:53 AM, Rob WX1N wrote:
Good morning,

I'm hoping for some basic info if one of you has the time to point me in the right direction. I know this is still a work in progress and I don't want to interfere with that, so if this isn't a quick answer, then please disregard.

I'm playing around with the new Bridge branches of HBlink and DMRlink. I wanted to see if I could successfully connect an MMDVM repeater to an IPSC network. I set it up as follows: MMDVM set to connect to local instance of HBlink (successful). HBlink configuration as a master to allow MMDVM to connect. Run MMDVMHost, run HB_Bridge.py. DMRlink configured as a peer to connect to the IPSC connection of 3102. Run IPSC_Bridge.py.
Results - MMDVM connects to HBlink and transmissions show in both HB_Bridge and IPSC_Bridge terminal windows, however, the transmissions don't seem to be making it through to the network. I think I am connected to 3102, as the repeater shows up in the 3102 status page (albeit as a SmartPTT network).

Does anyone have a guess as to where I'm going wrong?

Rob, WX1N











Re: Bridging from MMDVM repeater to IPSC network

Steve N4IRS
 

The connection from DMRlink to BM is as you say considered by BM as a SmartPTT connection. This does not happen on a connection from a Motorola Repeater. It's all about how BM treats a DMRLink connection.

On 6/23/2017 12:02 PM, Rob WX1N wrote:
Radio ID 313323, TS 1, TG 313324. Just to make sure I'm understanding this right - a valid IPSC connection to BM will pass absolutely nothing back and forth until it is preconfigured on the server end?

-----Original Message-----
From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of Steve N4IRS
Sent: Friday, June 23, 2017 12:00 PM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Bridging from MMDVM repeater to IPSC network

Let me be a little more clear. The connection from DMRlink to BM is as you say considered by BM as a SmartPTT connection. For a BM SmartPTT connection, a BM admin (I am one) has to configure the bridge in BM. I will need the following:
Radio_ID: in dmrlink.cfg
The TS and TG you want to bridge.

This can NOT be configured from a self care account.

On 6/23/2017 11:58 AM, Rob WX1N wrote:
Steve,
In the DMR link configuration, I'm signing in to 3102 as the repeater
ID, which has several static TG's preconfigured. I'm transmitting
using my personal ID, on one of the static TG's (although if I were
using a different TG, wouldn't it bring it up as a dynamic for a few
minutes?)

-----Original Message-----
From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of
Steve N4IRS
Sent: Friday, June 23, 2017 11:55 AM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Bridging from MMDVM repeater to IPSC network

Rob,
Is 3102 setup to bridge the TG you are trying from the Radio ID you are presenting to BM?

On 6/23/2017 11:53 AM, Rob WX1N wrote:
Good morning,

I'm hoping for some basic info if one of you has the time to point me in the right direction. I know this is still a work in progress and I don't want to interfere with that, so if this isn't a quick answer, then please disregard.

I'm playing around with the new Bridge branches of HBlink and DMRlink. I wanted to see if I could successfully connect an MMDVM repeater to an IPSC network. I set it up as follows: MMDVM set to connect to local instance of HBlink (successful). HBlink configuration as a master to allow MMDVM to connect. Run MMDVMHost, run HB_Bridge.py. DMRlink configured as a peer to connect to the IPSC connection of 3102. Run IPSC_Bridge.py.
Results - MMDVM connects to HBlink and transmissions show in both HB_Bridge and IPSC_Bridge terminal windows, however, the transmissions don't seem to be making it through to the network. I think I am connected to 3102, as the repeater shows up in the 3102 status page (albeit as a SmartPTT network).

Does anyone have a guess as to where I'm going wrong?

Rob, WX1N











Re: Bridging from MMDVM repeater to IPSC network

Rob WX1N
 

Radio ID 313323, TS 1, TG 313324. Just to make sure I'm understanding this right - a valid IPSC connection to BM will pass absolutely nothing back and forth until it is preconfigured on the server end?

-----Original Message-----
From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of Steve N4IRS
Sent: Friday, June 23, 2017 12:00 PM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Bridging from MMDVM repeater to IPSC network

Let me be a little more clear. The connection from DMRlink to BM is as you say considered by BM as a SmartPTT connection. For a BM SmartPTT connection, a BM admin (I am one) has to configure the bridge in BM. I will need the following:
Radio_ID: in dmrlink.cfg
The TS and TG you want to bridge.

This can NOT be configured from a self care account.

On 6/23/2017 11:58 AM, Rob WX1N wrote:
Steve,
In the DMR link configuration, I'm signing in to 3102 as the repeater
ID, which has several static TG's preconfigured. I'm transmitting
using my personal ID, on one of the static TG's (although if I were
using a different TG, wouldn't it bring it up as a dynamic for a few
minutes?)

-----Original Message-----
From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of
Steve N4IRS
Sent: Friday, June 23, 2017 11:55 AM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Bridging from MMDVM repeater to IPSC network

Rob,
Is 3102 setup to bridge the TG you are trying from the Radio ID you are presenting to BM?

On 6/23/2017 11:53 AM, Rob WX1N wrote:
Good morning,

I'm hoping for some basic info if one of you has the time to point me in the right direction. I know this is still a work in progress and I don't want to interfere with that, so if this isn't a quick answer, then please disregard.

I'm playing around with the new Bridge branches of HBlink and DMRlink. I wanted to see if I could successfully connect an MMDVM repeater to an IPSC network. I set it up as follows: MMDVM set to connect to local instance of HBlink (successful). HBlink configuration as a master to allow MMDVM to connect. Run MMDVMHost, run HB_Bridge.py. DMRlink configured as a peer to connect to the IPSC connection of 3102. Run IPSC_Bridge.py.
Results - MMDVM connects to HBlink and transmissions show in both HB_Bridge and IPSC_Bridge terminal windows, however, the transmissions don't seem to be making it through to the network. I think I am connected to 3102, as the repeater shows up in the 3102 status page (albeit as a SmartPTT network).

Does anyone have a guess as to where I'm going wrong?

Rob, WX1N








Re: Bridging from MMDVM repeater to IPSC network

Steve N4IRS
 

Let me be a little more clear. The connection from DMRlink to BM is as you say considered by BM as a SmartPTT connection. For a BM SmartPTT connection, a BM admin (I am one) has to configure the bridge in BM. I will need the following:
Radio_ID: in dmrlink.cfg
The TS and TG you want to bridge.

This can NOT be configured from a self care account.

On 6/23/2017 11:58 AM, Rob WX1N wrote:
Steve,
In the DMR link configuration, I'm signing in to 3102 as the repeater ID, which has several static TG's preconfigured. I'm transmitting using my personal ID, on one of the static TG's (although if I were using a different TG, wouldn't it bring it up as a dynamic for a few minutes?)

-----Original Message-----
From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of Steve N4IRS
Sent: Friday, June 23, 2017 11:55 AM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Bridging from MMDVM repeater to IPSC network

Rob,
Is 3102 setup to bridge the TG you are trying from the Radio ID you are presenting to BM?

On 6/23/2017 11:53 AM, Rob WX1N wrote:
Good morning,

I'm hoping for some basic info if one of you has the time to point me in the right direction. I know this is still a work in progress and I don't want to interfere with that, so if this isn't a quick answer, then please disregard.

I'm playing around with the new Bridge branches of HBlink and DMRlink. I wanted to see if I could successfully connect an MMDVM repeater to an IPSC network. I set it up as follows: MMDVM set to connect to local instance of HBlink (successful). HBlink configuration as a master to allow MMDVM to connect. Run MMDVMHost, run HB_Bridge.py. DMRlink configured as a peer to connect to the IPSC connection of 3102. Run IPSC_Bridge.py.
Results - MMDVM connects to HBlink and transmissions show in both HB_Bridge and IPSC_Bridge terminal windows, however, the transmissions don't seem to be making it through to the network. I think I am connected to 3102, as the repeater shows up in the 3102 status page (albeit as a SmartPTT network).

Does anyone have a guess as to where I'm going wrong?

Rob, WX1N







Re: Bridging from MMDVM repeater to IPSC network

Rob WX1N
 

Steve,
In the DMR link configuration, I'm signing in to 3102 as the repeater ID, which has several static TG's preconfigured. I'm transmitting using my personal ID, on one of the static TG's (although if I were using a different TG, wouldn't it bring it up as a dynamic for a few minutes?)

-----Original Message-----
From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of Steve N4IRS
Sent: Friday, June 23, 2017 11:55 AM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Bridging from MMDVM repeater to IPSC network

Rob,
Is 3102 setup to bridge the TG you are trying from the Radio ID you are presenting to BM?

On 6/23/2017 11:53 AM, Rob WX1N wrote:
Good morning,

I'm hoping for some basic info if one of you has the time to point me in the right direction. I know this is still a work in progress and I don't want to interfere with that, so if this isn't a quick answer, then please disregard.

I'm playing around with the new Bridge branches of HBlink and DMRlink. I wanted to see if I could successfully connect an MMDVM repeater to an IPSC network. I set it up as follows: MMDVM set to connect to local instance of HBlink (successful). HBlink configuration as a master to allow MMDVM to connect. Run MMDVMHost, run HB_Bridge.py. DMRlink configured as a peer to connect to the IPSC connection of 3102. Run IPSC_Bridge.py.
Results - MMDVM connects to HBlink and transmissions show in both HB_Bridge and IPSC_Bridge terminal windows, however, the transmissions don't seem to be making it through to the network. I think I am connected to 3102, as the repeater shows up in the 3102 status page (albeit as a SmartPTT network).

Does anyone have a guess as to where I'm going wrong?

Rob, WX1N



Re: Bridging from MMDVM repeater to IPSC network

Steve N4IRS
 

Rob,
Is 3102 setup to bridge the TG you are trying from the Radio ID you are presenting to BM?

On 6/23/2017 11:53 AM, Rob WX1N wrote:
Good morning,

I'm hoping for some basic info if one of you has the time to point me in the right direction. I know this is still a work in progress and I don't want to interfere with that, so if this isn't a quick answer, then please disregard.

I'm playing around with the new Bridge branches of HBlink and DMRlink. I wanted to see if I could successfully connect an MMDVM repeater to an IPSC network. I set it up as follows: MMDVM set to connect to local instance of HBlink (successful). HBlink configuration as a master to allow MMDVM to connect. Run MMDVMHost, run HB_Bridge.py. DMRlink configured as a peer to connect to the IPSC connection of 3102. Run IPSC_Bridge.py.
Results - MMDVM connects to HBlink and transmissions show in both HB_Bridge and IPSC_Bridge terminal windows, however, the transmissions don't seem to be making it through to the network. I think I am connected to 3102, as the repeater shows up in the 3102 status page (albeit as a SmartPTT network).

Does anyone have a guess as to where I'm going wrong?

Rob, WX1N


Bridging from MMDVM repeater to IPSC network

Rob WX1N
 

Good morning,

I'm hoping for some basic info if one of you has the time to point me in the right direction. I know this is still a work in progress and I don't want to interfere with that, so if this isn't a quick answer, then please disregard.

I'm playing around with the new Bridge branches of HBlink and DMRlink. I wanted to see if I could successfully connect an MMDVM repeater to an IPSC network. I set it up as follows: MMDVM set to connect to local instance of HBlink (successful). HBlink configuration as a master to allow MMDVM to connect. Run MMDVMHost, run HB_Bridge.py. DMRlink configured as a peer to connect to the IPSC connection of 3102. Run IPSC_Bridge.py.
Results - MMDVM connects to HBlink and transmissions show in both HB_Bridge and IPSC_Bridge terminal windows, however, the transmissions don't seem to be making it through to the network. I think I am connected to 3102, as the repeater shows up in the 3102 status page (albeit as a SmartPTT network).

Does anyone have a guess as to where I'm going wrong?

Rob, WX1N


Re: Analog_Bridge for the Raspberry Pi

Steve N4IRS
 

I hope it will be a short delay. Once we have a validation program, we will know more. One of the options we are considering is to change the RPi version of Analog_bridge WITHOUT support for USB. It would be AMBEserver only.
Once we have the validation program I will test on other ARM based systems. OrangePi, NanoPi, Odroid etc.

On 6/22/2017 12:33 PM, Steve Siesel [K4KSA] wrote:

Do you think this is a short delay…making it work in a Pi? If not I have a HP SFF PC to use…Probably a little over the top…

 

8 gb of Ram

500 mb SSD

3.16 Core 2 Duo cpu….

 

Thoughts?

 

 

From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of Steve N4IRS
Sent: Thursday, June 22, 2017 10:30 AM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Analog_Bridge for the Raspberry Pi

 

We have been talking to them for a while.

Thanks, Steve

On 6/22/2017 10:29 AM, Peter M0NWI wrote:

Hi Steve,

 

Looking at NWDigital's site the GPIO version is out of stock, and they are recommending people purchase the DV3000u, so if there's issues maybe they could assist?

 

73,

Peter

 


From: DVSwitch@groups.io <DVSwitch@groups.io> on behalf of Steve N4IRS <szingman@...>
Sent: 22 June 2017 15:14
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Analog_Bridge for the Raspberry Pi

 

It's actually specific to the ThumbDv (DV3000u) It may well be power. The existing initialization code follows the NWDigital spec but does not prove actual valid data to and from the Vocoder.
As a note, we are not seeing the problem with the GPIO based Vocoder. I'll follow up as we know more.

Steve 

On 6/22/2017 9:54 AM, Matthew 2E0SIP wrote:

Does this include ThumbDV dongles?

If it's solely power related, maybe using a powered USB hub will help?

Thanks

 

 



Re: Analog_Bridge for the Raspberry Pi

Steve Siesel [K4KSA]
 

Do you think this is a short delay…making it work in a Pi? If not I have a HP SFF PC to use…Probably a little over the top…

 

8 gb of Ram

500 mb SSD

3.16 Core 2 Duo cpu….

 

Thoughts?

 

 

From: DVSwitch@groups.io [mailto:DVSwitch@groups.io] On Behalf Of Steve N4IRS
Sent: Thursday, June 22, 2017 10:30 AM
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Analog_Bridge for the Raspberry Pi

 

We have been talking to them for a while.

Thanks, Steve

On 6/22/2017 10:29 AM, Peter M0NWI wrote:

Hi Steve,

 

Looking at NWDigital's site the GPIO version is out of stock, and they are recommending people purchase the DV3000u, so if there's issues maybe they could assist?

 

73,

Peter

 


From: DVSwitch@groups.io <DVSwitch@groups.io> on behalf of Steve N4IRS <szingman@...>
Sent: 22 June 2017 15:14
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Analog_Bridge for the Raspberry Pi

 

It's actually specific to the ThumbDv (DV3000u) It may well be power. The existing initialization code follows the NWDigital spec but does not prove actual valid data to and from the Vocoder.
As a note, we are not seeing the problem with the GPIO based Vocoder. I'll follow up as we know more.

Steve 

On 6/22/2017 9:54 AM, Matthew 2E0SIP wrote:

Does this include ThumbDV dongles?

If it's solely power related, maybe using a powered USB hub will help?

Thanks

 

 


Re: Analog_Bridge for the Raspberry Pi

Steve N4IRS
 

We have been talking to them for a while.

Thanks, Steve

On 6/22/2017 10:29 AM, Peter M0NWI wrote:

Hi Steve,


Looking at NWDigital's site the GPIO version is out of stock, and they are recommending people purchase the DV3000u, so if there's issues maybe they could assist?


73,

Peter



From: DVSwitch@groups.io <DVSwitch@groups.io> on behalf of Steve N4IRS <szingman@...>
Sent: 22 June 2017 15:14
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Analog_Bridge for the Raspberry Pi
 
It's actually specific to the ThumbDv (DV3000u) It may well be power. The existing initialization code follows the NWDigital spec but does not prove actual valid data to and from the Vocoder.
As a note, we are not seeing the problem with the GPIO based Vocoder. I'll follow up as we know more.

Steve 

On 6/22/2017 9:54 AM, Matthew 2E0SIP wrote:

Does this include ThumbDV dongles?

If it's solely power related, maybe using a powered USB hub will help?

Thanks




Re: Analog_Bridge for the Raspberry Pi

Peter M0NWI
 

Hi Steve,


Looking at NWDigital's site the GPIO version is out of stock, and they are recommending people purchase the DV3000u, so if there's issues maybe they could assist?


73,

Peter



From: DVSwitch@groups.io <DVSwitch@groups.io> on behalf of Steve N4IRS <szingman@...>
Sent: 22 June 2017 15:14
To: DVSwitch@groups.io
Subject: Re: [DVSwitch] Analog_Bridge for the Raspberry Pi
 
It's actually specific to the ThumbDv (DV3000u) It may well be power. The existing initialization code follows the NWDigital spec but does not prove actual valid data to and from the Vocoder.
As a note, we are not seeing the problem with the GPIO based Vocoder. I'll follow up as we know more.

Steve 

On 6/22/2017 9:54 AM, Matthew 2E0SIP wrote:

Does this include ThumbDV dongles?

If it's solely power related, maybe using a powered USB hub will help?

Thanks



Re: Analog_Bridge for the Raspberry Pi

Steve N4IRS
 

It's actually specific to the ThumbDv (DV3000u) It may well be power. The existing initialization code follows the NWDigital spec but does not prove actual valid data to and from the Vocoder.
As a note, we are not seeing the problem with the GPIO based Vocoder. I'll follow up as we know more.

Steve 

On 6/22/2017 9:54 AM, Matthew 2E0SIP wrote:

Does this include ThumbDV dongles?

If it's solely power related, maybe using a powered USB hub will help?

Thanks



Re: Analog_Bridge for the Raspberry Pi

Matthew 2E0SIP
 

Does this include ThumbDV dongles?

If it's solely power related, maybe using a powered USB hub will help?

Thanks


Analog_Bridge for the Raspberry Pi

Steve N4IRS
 

Due to ongoing issues with the DV3000 and the Raspberry Pi, I have removed Analog_Bridge for the Pi from the repository. 


Re: Preparing to Build

Steve N4IRS
 

They are close enough. At some point I will edit.We are testing the DV3000u on a Pi with mixed results. Mike is building a validation program. As of right now, the DV3000u is not supported on the Pi.

Steve

On 6/22/2017 8:02 AM, Steve Siesel [K4KSA] wrote:
Steve and all,

I will begin to build this weekend my ASL to DMR gateway and want to know if
the DV3000 install instructions in the file "Draft DMRGateway Install notes"
found in the
DVSwitch files area is still valid?

Thanks,

Steve
K4KSA






Preparing to Build

Steve Siesel [K4KSA]
 

Steve and all,

I will begin to build this weekend my ASL to DMR gateway and want to know if
the DV3000 install instructions in the file "Draft DMRGateway Install notes"
found in the
DVSwitch files area is still valid?

Thanks,

Steve
K4KSA


Re: Analog_Bridge overview

G7RPG - Peter Kendall
 

X86 Atom N570, Linux Mint 18.1


On 21/06/2017 22:07, Steve N4IRS wrote:
Peter,
What hardware are you running the DV3000u on?


Re: Analog_Bridge overview

Steve N4IRS
 

Peter,
What hardware are you running the DV3000u on?


Re: Testing HBlink

Mike Zingman - N4IRR
 

What hardware/computer are you running the Analog_Bridge on?  Is the DV3000 connected locally or is it on an AMBE server?
We have seen that the DV3000 is very sensitive to power from the USB port and looking to see if yours is producing proper voltage levels.

9721 - 9740 of 9882