Date   

Re: not connecting to Brandmeister still

Steve N4IRS
 

Show us your MMDVM_Bridge.ini

On 7/18/2018 3:05 PM, mark rosenberg wrote:
sure.  btw...I just ran the foreground status of the mmdvm bridge....like this.... sudo ./ MMDVM_Bridge MMDVM_Bridge.ini  and i am attaching a pic of the results...error 13...see attached.

Please send me an email to my 4x1ks.mark@...
address so I can set you up to SSH.  Tell me what you need to get in. 


Re: not connecting to Brandmeister still

mark rosenberg
 

sure.  btw...I just ran the foreground status of the mmdvm bridge....like this.... sudo ./ MMDVM_Bridge MMDVM_Bridge.ini  and i am attaching a pic of the results...error 13...see attached.

Please send me an email to my 4x1ks.mark@...
address so I can set you up to SSH.  Tell me what you need to get in. 


Re: C Bridge to P25 Reflector

Steve N4IRS
 

Joe,
I will try to review the config tonight or tomorrow.

Steve

On 7/18/2018 3:03 PM, KD5DFB wrote:
All, I still need help with my bridge. I have voice traffic to hb bridge on the dmr side and p25 voice traffic to the analog bridge. Still struggling to understand how to get these 2 connected . 

As always, Thank you for your help Steve! 

On Tue, Jul 17, 2018 at 1:51 PM, Steve N4IRS <szingman@...> wrote:
##################################              ################################
# IPSC_Bridge configuration file #              #
HB_Bridge configuration file #           
##################################              ################################

[DEFAULTS]                                      [DEFAULTS]
gateway = 127.0.0.1                            
gateway = 127.0.0.1                             
fromGatewayPort = 31000                        
toGatewayPort = 31000
toGatewayPort = 31003                          
fromGatewayPort = 31003                          


The above assumes you are not using those port number somewhere else. If you are, make the unique.
example: change 31000 to 31999 change 31003 to 31993

On 7/17/2018 2:38 PM, KD5DFB wrote:
Steve, I really appreciate your help! My apologies, but, I just can see it. 

On Tue, Jul 17, 2018 at 12:57 PM, Steve N4IRS <szingman@...> wrote:
dmrlink.cfg and hblink.cfg define their respective network connections. IPSC_Bridge.cfg and HB_Bridge.cfg define their respective Partner connections.

On 7/17/2018 1:55 PM, KD5DFB wrote:
Okay, let me take a step back and break it down again. 

So, IPSC_Bridge uses both dmrlink.cfg and IPSC_bridge.cfg.  The dmrlink.cfg defines the connection to the cbridge and I see it connected on the control center. IPSC_Bridge.cfg defines the connection to HB_Bridge. Is that defined in the HB_Bridge.cfg or hblink.cfg?

On Tue, Jul 17, 2018 at 12:44 PM, Steve N4IRS <szingman@...> wrote:
No,
You can use the same port number twice. I try to use the default port numbers where possible. Since you can't use a port twice, you will have to change something. 

On 7/17/2018 1:38 PM, KD5DFB wrote:
Ok, so let me see if I got it correct. So basically all 3 of them use the same port numbers just changing the TX and RX? 

IPSC_Bridge.cfg                     HB_Bridge.cfg                  Analog_Bridge.ini
fromgateway: 31100              fromGateway: 31103         from: 31100
toGateway: 31103                  toGateway: 31100            to: 31103

On Tue, Jul 17, 2018 at 10:00 AM, Steve N4IRS <szingman@...> wrote:


On 7/17/2018 10:51 AM, KD5DFB wrote:
Okay, making progress! I am stumped on the last piece. 

I am trying to figure out the connection between ipsc_bridge and hb_bridge. 

On ipsc_bridge, I have the dmrlink.cfg connecting to the cbridge and can see traffic from the cbridge in the log. Does the ipsc_bridge.cfg connect to hb_bridge.cfg?
Yes

On the hb_bridge I am a little confused. Does the hb_bridge.cfg connect to analog_bridge? Does the ambe need to match what is in analog_bridge?
Just like connecting any of the partners, TX to RX and RX to TX (or words to that effect) Analog_Bridge [AMBE_AUDIO] stanza points to the values in the HB_Bridge [DEFAULTS] stanza.

[AMBE]
EXPORT_IP: 127.0.0.1
EXPORT_PORT: 1234
Ignore these


On Mon, Jul 16, 2018, 21:02 Steve N4IRS <szingman@...> wrote:
I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.
 

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB



















Re: C Bridge to P25 Reflector

Michael KD5DFB
 

All, I still need help with my bridge. I have voice traffic to hb bridge on the dmr side and p25 voice traffic to the analog bridge. Still struggling to understand how to get these 2 connected . 

As always, Thank you for your help Steve! 

On Tue, Jul 17, 2018 at 1:51 PM, Steve N4IRS <szingman@...> wrote:
##################################              ################################
# IPSC_Bridge configuration file #              #
HB_Bridge configuration file #           
##################################              ################################

[DEFAULTS]                                      [DEFAULTS]
gateway = 127.0.0.1                            
gateway = 127.0.0.1                             
fromGatewayPort = 31000                        
toGatewayPort = 31000
toGatewayPort = 31003                          
fromGatewayPort = 31003                          


The above assumes you are not using those port number somewhere else. If you are, make the unique.
example: change 31000 to 31999 change 31003 to 31993

On 7/17/2018 2:38 PM, KD5DFB wrote:
Steve, I really appreciate your help! My apologies, but, I just can see it. 

On Tue, Jul 17, 2018 at 12:57 PM, Steve N4IRS <szingman@...> wrote:
dmrlink.cfg and hblink.cfg define their respective network connections. IPSC_Bridge.cfg and HB_Bridge.cfg define their respective Partner connections.

On 7/17/2018 1:55 PM, KD5DFB wrote:
Okay, let me take a step back and break it down again. 

So, IPSC_Bridge uses both dmrlink.cfg and IPSC_bridge.cfg.  The dmrlink.cfg defines the connection to the cbridge and I see it connected on the control center. IPSC_Bridge.cfg defines the connection to HB_Bridge. Is that defined in the HB_Bridge.cfg or hblink.cfg?

On Tue, Jul 17, 2018 at 12:44 PM, Steve N4IRS <szingman@...> wrote:
No,
You can use the same port number twice. I try to use the default port numbers where possible. Since you can't use a port twice, you will have to change something. 

On 7/17/2018 1:38 PM, KD5DFB wrote:
Ok, so let me see if I got it correct. So basically all 3 of them use the same port numbers just changing the TX and RX? 

IPSC_Bridge.cfg                     HB_Bridge.cfg                  Analog_Bridge.ini
fromgateway: 31100              fromGateway: 31103         from: 31100
toGateway: 31103                  toGateway: 31100            to: 31103

On Tue, Jul 17, 2018 at 10:00 AM, Steve N4IRS <szingman@...> wrote:


On 7/17/2018 10:51 AM, KD5DFB wrote:
Okay, making progress! I am stumped on the last piece. 

I am trying to figure out the connection between ipsc_bridge and hb_bridge. 

On ipsc_bridge, I have the dmrlink.cfg connecting to the cbridge and can see traffic from the cbridge in the log. Does the ipsc_bridge.cfg connect to hb_bridge.cfg?
Yes

On the hb_bridge I am a little confused. Does the hb_bridge.cfg connect to analog_bridge? Does the ambe need to match what is in analog_bridge?
Just like connecting any of the partners, TX to RX and RX to TX (or words to that effect) Analog_Bridge [AMBE_AUDIO] stanza points to the values in the HB_Bridge [DEFAULTS] stanza.

[AMBE]
EXPORT_IP: 127.0.0.1
EXPORT_PORT: 1234
Ignore these


On Mon, Jul 16, 2018, 21:02 Steve N4IRS <szingman@...> wrote:
I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.
 

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB


















Re: not connecting to Brandmeister still

Steve N4IRS
 

Can I ssh in?

Steve N4IRS

On 7/18/2018 2:26 PM, mark rosenberg wrote:

For some reason it is not showing up under myhotspots in Brandmeister.  

I tried running ./MMDVM_Bridge MMDVM_Bridge.ini  per page 10 of the how to.  I got "unable to run log file" or something close to that so I did not get the feedback of "Logged into the master successfully" per page 11 of the howto.

I am running this on the vultr cloud server.  Anyone have an idea?

thanks 

Mark



not connecting to Brandmeister still

mark rosenberg
 

For some reason it is not showing up under myhotspots in Brandmeister.  

I tried running ./MMDVM_Bridge MMDVM_Bridge.ini  per page 10 of the how to.  I got "unable to run log file" or something close to that so I did not get the feedback of "Logged into the master successfully" per page 11 of the howto.

I am running this on the vultr cloud server.  Anyone have an idea?

thanks 

Mark


Re: setting up MMDVM_Bridge.ini

mark rosenberg
 

Ok i will add a digit to the ID which is 1 line under callsign.  When i run the status check on the md380 emulator it is ok.  I am thinking something else is going on but i was fairly careful to edit all the lines of code that were in the how to file.   

Part A...which was setting up the node itself went well.  The virtual node is working and i can connect to it from the physical node in my shack.  

Part B...the DMR Bridge setup had a problem with an error of "unable to resolve host"...i corrected that and then everything loaded and the emulator works...but i am missing the link between the key up on the tg with my dmr radio and the bridge to the virtual node...



On Wed, Jul 18, 2018, 18:59 Russell, KV4S <russelljthomas@...> wrote:
Hey Mark,
it's essentially the same thing, MMDVM is creating a virtual hotspot/repeater for you to connect.
Brandmeister best practice is to use the extra digit when you have multiple systems.

On Wed, Jul 18, 2018 at 10:52 AM mark rosenberg <4x1ks.mark@...> wrote:
I am not using a hotspot.  I am using a virtual node which is hosted on vurtl cloud

On Wed, Jul 18, 2018, 18:50 Alec-N1AJW <alec.wasserman@...> wrote:
7 digit dmr id and 2 then two number 01-99 to distinquish that hotspot.  pick anything not in use by you.


Re: setting up MMDVM_Bridge.ini

Mike KB8JNM
 

I can't speak to someone else's guide. See them for answers.

There is no 2 digit ID.

There is appending your ID with 2 digits in the 'correct places'.

Perhaps if you read this official document / how-2, you would understand. It's in there.

https://docs.google.com/document/d/1eN50Csr29eAprBu7eKA0Bfa2XUcsXw5iktY1Ey-Qjkg/edit

...mike/kb8jnm


On 07/18/2018 11:28 AM, mark rosenberg wrote:
What is the 2 digit id? In the video chris used only hos dmr id

On Wed, Jul 18, 2018, 17:44 Ramon (kp4tr) <kp4tr.ramon@...> wrote:
Docs say its your DMR id and a 2 digit SSID to distinguish it 

On Wed, Jul 18, 2018 at 10:31 AM mark rosenberg <4x1ks.mark@...> wrote:
I am setting up a DMR to Allstar link.  I noticed is the file MMDVM_Bridge.ini there is a place for callsign followed by ID....What is this ID?  It can't be the Brandmeister ID because it is too many digits.

Also, I don't see anywhere in the files that my node number is inserted.  How does the Bridge know that it is bridged to my node?  I set up a virtual node in the cloud, I am not using a rpi3 for this node.

Thanks for any help

Mark
--


Re: setting up MMDVM_Bridge.ini

 

Hey Mark,
it's essentially the same thing, MMDVM is creating a virtual hotspot/repeater for you to connect.
Brandmeister best practice is to use the extra digit when you have multiple systems.


On Wed, Jul 18, 2018 at 10:52 AM mark rosenberg <4x1ks.mark@...> wrote:
I am not using a hotspot.  I am using a virtual node which is hosted on vurtl cloud

On Wed, Jul 18, 2018, 18:50 Alec-N1AJW <alec.wasserman@...> wrote:
7 digit dmr id and 2 then two number 01-99 to distinquish that hotspot.  pick anything not in use by you.


Re: setting up MMDVM_Bridge.ini

mark rosenberg
 

I am not using a hotspot.  I am using a virtual node which is hosted on vurtl cloud


On Wed, Jul 18, 2018, 18:50 Alec-N1AJW <alec.wasserman@...> wrote:
7 digit dmr id and 2 then two number 01-99 to distinquish that hotspot.  pick anything not in use by you.


Re: setting up MMDVM_Bridge.ini

Alec-N1AJW
 

7 digit dmr id and 2 then two number 01-99 to distinquish that hotspot.  pick anything not in use by you.


Re: setting up MMDVM_Bridge.ini

mark rosenberg
 

What is the 2 digit id? In the video chris used only hos dmr id


On Wed, Jul 18, 2018, 17:44 Ramon (kp4tr) <kp4tr.ramon@...> wrote:
Docs say its your DMR id and a 2 digit SSID to distinguish it 

On Wed, Jul 18, 2018 at 10:31 AM mark rosenberg <4x1ks.mark@...> wrote:
I am setting up a DMR to Allstar link.  I noticed is the file MMDVM_Bridge.ini there is a place for callsign followed by ID....What is this ID?  It can't be the Brandmeister ID because it is too many digits.

Also, I don't see anywhere in the files that my node number is inserted.  How does the Bridge know that it is bridged to my node?  I set up a virtual node in the cloud, I am not using a rpi3 for this node.

Thanks for any help

Mark

--


Re: setting up MMDVM_Bridge.ini

Mike KB8JNM
 

Sorry, I forgot to give you the link for a dmr ID.

https://radioid.net/cgi-bin/trbo-database/userreg.cgi

You may have to wait a day or two to get reply.

Do not apply for more than one ID. That is what the appending is for explain a bit in that how-2 draft.

https://radioid.net/cgi-bin/trbo-database/userreg.cgi

Anyway, those 2 things should get you going.

...mike/kb8jnm


On 07/18/2018 10:31 AM, mark rosenberg wrote:
I am setting up a DMR to Allstar link.  I noticed is the file MMDVM_Bridge.ini there is a place for callsign followed by ID....What is this ID?  It can't be the Brandmeister ID because it is too many digits.

Also, I don't see anywhere in the files that my node number is inserted.  How does the Bridge know that it is bridged to my node?  I set up a virtual node in the cloud, I am not using a rpi3 for this node.

Thanks for any help

Mark


Re: setting up MMDVM_Bridge.ini

Mike KB8JNM
 

You do not set-up your node in mmdvm bridge or any of the dvswitch package files.

You set them to use USRP

You set your very minimal node (public or private) to use the USRP driver.

The DMR ID is the only 'IDs' you need for the packages.(assuming you are making a DMR Bridge)

Use the guide to know where to use your issued ID and your appended ID.

https://docs.google.com/document/d/1eN50Csr29eAprBu7eKA0Bfa2XUcsXw5iktY1Ey-Qjkg/edit

...mike/kb8jnm



On 07/18/2018 10:31 AM, mark rosenberg wrote:
I am setting up a DMR to Allstar link.  I noticed is the file MMDVM_Bridge.ini there is a place for callsign followed by ID....What is this ID?  It can't be the Brandmeister ID because it is too many digits.

Also, I don't see anywhere in the files that my node number is inserted.  How does the Bridge know that it is bridged to my node?  I set up a virtual node in the cloud, I am not using a rpi3 for this node.

Thanks for any help

Mark


Re: setting up MMDVM_Bridge.ini

Ramon (kp4tr) <kp4tr.ramon@...>
 

Docs say its your DMR id and a 2 digit SSID to distinguish it 

On Wed, Jul 18, 2018 at 10:31 AM mark rosenberg <4x1ks.mark@...> wrote:
I am setting up a DMR to Allstar link.  I noticed is the file MMDVM_Bridge.ini there is a place for callsign followed by ID....What is this ID?  It can't be the Brandmeister ID because it is too many digits.

Also, I don't see anywhere in the files that my node number is inserted.  How does the Bridge know that it is bridged to my node?  I set up a virtual node in the cloud, I am not using a rpi3 for this node.

Thanks for any help

Mark

--


setting up MMDVM_Bridge.ini

mark rosenberg
 

I am setting up a DMR to Allstar link.  I noticed is the file MMDVM_Bridge.ini there is a place for callsign followed by ID....What is this ID?  It can't be the Brandmeister ID because it is too many digits.

Also, I don't see anywhere in the files that my node number is inserted.  How does the Bridge know that it is bridged to my node?  I set up a virtual node in the cloud, I am not using a rpi3 for this node.

Thanks for any help

Mark


Re: error message while setting up DMR bridge

mark rosenberg
 

I figured it out!  Very happy i was able to find it. Thanks


On Wed, Jul 18, 2018, 16:16 Mike KB8JNM <groupio@...> wrote:
I doubt any of us know the instructions you have been following to have a idea where you might have gone wrong or where you are in the install.

Here is the official HOW-2 draft:

https://docs.google.com/document/d/1eN50Csr29eAprBu7eKA0Bfa2XUcsXw5iktY1Ey-Qjkg/edit

...mike/kb8jnm



On 07/18/2018 08:10 AM, 4x1ks.mark@... wrote:
Hello:

I am going through the setup of DMR bridge by Chris Hood.  So far so good, except that after I saved the changes to the /etc/asterisk .conf files, I tried to do a "sudo astres.sh"  and got an error  "unable to resolve host"
The subsequent line was restarting asterisk, but when I moved to the next step in the process, which is to run

sudo systemctl enable md380-emu

I also got another 

unable to resolve host

I'm stuck.  I am using the vultr cloud server 

Any help would be very much appreciated. I am setting up a link between DMR and Allstar.  The Allstar virtual node is up and running fine and I can connect to it from my actual node in my shack.

thanks 

Mark


Re: error message while setting up DMR bridge

Mike KB8JNM
 

I doubt any of us know the instructions you have been following to have a idea where you might have gone wrong or where you are in the install.

Here is the official HOW-2 draft:

https://docs.google.com/document/d/1eN50Csr29eAprBu7eKA0Bfa2XUcsXw5iktY1Ey-Qjkg/edit

...mike/kb8jnm



On 07/18/2018 08:10 AM, 4x1ks.mark@... wrote:
Hello:

I am going through the setup of DMR bridge by Chris Hood.  So far so good, except that after I saved the changes to the /etc/asterisk .conf files, I tried to do a "sudo astres.sh"  and got an error  "unable to resolve host"
The subsequent line was restarting asterisk, but when I moved to the next step in the process, which is to run

sudo systemctl enable md380-emu

I also got another 

unable to resolve host

I'm stuck.  I am using the vultr cloud server 

Any help would be very much appreciated. I am setting up a link between DMR and Allstar.  The Allstar virtual node is up and running fine and I can connect to it from my actual node in my shack.

thanks 

Mark


error message while setting up DMR bridge

mark rosenberg
 

Hello:

I am going through the setup of DMR bridge by Chris Hood.  So far so good, except that after I saved the changes to the /etc/asterisk .conf files, I tried to do a "sudo astres.sh"  and got an error  "unable to resolve host"
The subsequent line was restarting asterisk, but when I moved to the next step in the process, which is to run

sudo systemctl enable md380-emu

I also got another 

unable to resolve host

I'm stuck.  I am using the vultr cloud server 

Any help would be very much appreciated. I am setting up a link between DMR and Allstar.  The Allstar virtual node is up and running fine and I can connect to it from my actual node in my shack.

thanks 

Mark


Re: C Bridge to P25 Reflector

Michael KD5DFB
 

Hopefully this is my issue. Do I need a MMDVM_Bridge between the hb_bridge and Analog_Bridge 1 ?? I do not see how to connect hb_bridge to analog_bridge


                                                       MMDVM_Bridge           
                                                                V 
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector 

On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB


7961 - 7980 of 9820