Date   

Re: DMR<-->P25 Now only one way Audio

Steve N4IRS
 

Then the problem is at MMDVM_Bridge. Absolutely nothing in the MMDVM_Bridge log when you TX on P25 through the reflector? Nothing strange in the startup of MMDVM_Bridge?

On 1/4/19 5:43 PM, Ian Tulley wrote:
Hi Steve, well that’s the problem, when I PTT of P25, I can see myself on the Reflector, but nothing on mmdvm_bridge log or and of the analog_bridge logs ??

------------------
Regards
Ian (VK2HK)




On 5 Jan 2019, at 9:20 am, Steve N4IRS <szingman@...> wrote:

Follow the data in the logs from program to program. Do you see the data in the log for MMDVM_Bridge? if yes, move on to analog_bridge. Same question. rinse repeat.

On 1/4/19 4:52 PM, Ian Tulley wrote:
Hi all, I recently had active a DMR <--> P25 Bridge with the help of Steve. There was an issue with setting up the audio due to some problem associated with md380-emu, but it was fixed and the bridge worked great and after some tweaking the audio and audio levels in both directions just worked. I have been monitoring for a couple of days and found last night that I only had audio from DMR to P25 but not in the reverse direction. This morning I have been trying hard to solve this issue but just cannot find out why.
This is on a VPS and I am running the P25Reflector/Gateway/Bridge plus NXDN Reflector and YSF Reflector all off the same server, but when the bridge was working all of this was running at the same time.
This is what I have done so far, so any further suggestions would be welcome.

Checked status of all services to make sure all running and yes all OK
Set both P25Reflector and P25Gateway into Debug mode and monitored the output but nothing found.
restarted all services but again no difference.
stoped md30-emu
stopped mmdvm_bridge
stopped analog_bridge_p25 and analog_bridge_dmr
restarted all services manually in seperate windows so I could monitor the output to the screen.

Results I am getting, 
If I key up on the P25 radio, I get nothing coming to any of the screen outputs, but can hear myself via another connected P25 Hotspot so I know the reflector is working OK
If I key up on DMR I can see all 3 screen outputs and can hear myself out of the P25 Radio.

Anyone have any idea where to start to look for this issue.

Ian (VK2HK)
 




Re: DMR<-->P25 Now only one way Audio

Ian Tulley
 

Hi Steve, well that’s the problem, when I PTT of P25, I can see myself on the Reflector, but nothing on mmdvm_bridge log or and of the analog_bridge logs ??

------------------
Regards
Ian (VK2HK)




On 5 Jan 2019, at 9:20 am, Steve N4IRS <szingman@...> wrote:

Follow the data in the logs from program to program. Do you see the data in the log for MMDVM_Bridge? if yes, move on to analog_bridge. Same question. rinse repeat.

On 1/4/19 4:52 PM, Ian Tulley wrote:
Hi all, I recently had active a DMR <--> P25 Bridge with the help of Steve. There was an issue with setting up the audio due to some problem associated with md380-emu, but it was fixed and the bridge worked great and after some tweaking the audio and audio levels in both directions just worked. I have been monitoring for a couple of days and found last night that I only had audio from DMR to P25 but not in the reverse direction. This morning I have been trying hard to solve this issue but just cannot find out why.
This is on a VPS and I am running the P25Reflector/Gateway/Bridge plus NXDN Reflector and YSF Reflector all off the same server, but when the bridge was working all of this was running at the same time.
This is what I have done so far, so any further suggestions would be welcome.

Checked status of all services to make sure all running and yes all OK
Set both P25Reflector and P25Gateway into Debug mode and monitored the output but nothing found.
restarted all services but again no difference.
stoped md30-emu
stopped mmdvm_bridge
stopped analog_bridge_p25 and analog_bridge_dmr
restarted all services manually in seperate windows so I could monitor the output to the screen.

Results I am getting, 
If I key up on the P25 radio, I get nothing coming to any of the screen outputs, but can hear myself via another connected P25 Hotspot so I know the reflector is working OK
If I key up on DMR I can see all 3 screen outputs and can hear myself out of the P25 Radio.

Anyone have any idea where to start to look for this issue.

Ian (VK2HK)
 



Re: DMR<-->P25 Now only one way Audio

Steve N4IRS
 

Follow the data in the logs from program to program. Do you see the data in the log for MMDVM_Bridge? if yes, move on to analog_bridge. Same question. rinse repeat.

On 1/4/19 4:52 PM, Ian Tulley wrote:
Hi all, I recently had active a DMR <--> P25 Bridge with the help of Steve. There was an issue with setting up the audio due to some problem associated with md380-emu, but it was fixed and the bridge worked great and after some tweaking the audio and audio levels in both directions just worked. I have been monitoring for a couple of days and found last night that I only had audio from DMR to P25 but not in the reverse direction. This morning I have been trying hard to solve this issue but just cannot find out why.
This is on a VPS and I am running the P25Reflector/Gateway/Bridge plus NXDN Reflector and YSF Reflector all off the same server, but when the bridge was working all of this was running at the same time.
This is what I have done so far, so any further suggestions would be welcome.

Checked status of all services to make sure all running and yes all OK
Set both P25Reflector and P25Gateway into Debug mode and monitored the output but nothing found.
restarted all services but again no difference.
stoped md30-emu
stopped mmdvm_bridge
stopped analog_bridge_p25 and analog_bridge_dmr
restarted all services manually in seperate windows so I could monitor the output to the screen.

Results I am getting, 
If I key up on the P25 radio, I get nothing coming to any of the screen outputs, but can hear myself via another connected P25 Hotspot so I know the reflector is working OK
If I key up on DMR I can see all 3 screen outputs and can hear myself out of the P25 Radio.

Anyone have any idea where to start to look for this issue.

Ian (VK2HK)
 


Re: Setting up DMRLink <-> KBLink #best_practices #dmrlink #hblink

Jason Johnston
 

I *think* I have everything setup.  But when I run "python IPSC_Bridge.py" it doesn't login to my cbridge... that is, I don't see it on my Peer Watch or admin Netwatch screen.  But it does seem to be logging in...somewhere... and working.  Here are the results of running that script

<snip>
root@DMRlink1:/opt/DMRlink# python IPSC_Bridge.py
INFO 2019-01-04 15:55:47,493 DMRlink 'IPSC_Bridge.py' (c) 2015 N0MJS & the K0USY Group - SYSTEM STARTING...
INFO 2019-01-04 15:55:47,493 Version 20170620
INFO 2019-01-04 15:55:47,591 ID ALIAS MAPPER: 'peer_ids.csv' could not be downloaded
INFO 2019-01-04 15:55:47,886 ID ALIAS MAPPER: 'subscriber_ids.csv' could not be downloaded
INFO 2019-01-04 15:55:47,886 (SAMPLE_PEER) IPSC Instance Created: 114810, 0.0.0.0:50000
INFO 2019-01-04 15:55:47,887 section = SAMPLE_PEER
INFO 2019-01-04 15:55:47,887 Section SAMPLE_PEER was not found, using DEFAULTS
INFO 2019-01-04 15:55:47,888 gateway = 127.0.0.1
INFO 2019-01-04 15:55:47,888 toGatewayPort = 31003
INFO 2019-01-04 15:55:47,888 fromGatewayPort = 31000
INFO 2019-01-04 15:55:47,888 DMRLink IPSC Bridge
INFO 2019-01-04 15:55:47,892 (SAMPLE_PEER) Registering with the Master: ##########
WARNING 2019-01-04 15:55:48,960 (SAMPLE_PEER) Registration response (we requested reg) from the Master: 1114810, ######### (0 peers)
</snip>

Once it is ready to go... what is the command to launch everything in the background, and how can I make sure it autostarts when the system is rebooted?


DMR<-->P25 Now only one way Audio

Ian Tulley
 

Hi all, I recently had active a DMR <--> P25 Bridge with the help of Steve. There was an issue with setting up the audio due to some problem associated with md380-emu, but it was fixed and the bridge worked great and after some tweaking the audio and audio levels in both directions just worked. I have been monitoring for a couple of days and found last night that I only had audio from DMR to P25 but not in the reverse direction. This morning I have been trying hard to solve this issue but just cannot find out why.
This is on a VPS and I am running the P25Reflector/Gateway/Bridge plus NXDN Reflector and YSF Reflector all off the same server, but when the bridge was working all of this was running at the same time.
This is what I have done so far, so any further suggestions would be welcome.

Checked status of all services to make sure all running and yes all OK
Set both P25Reflector and P25Gateway into Debug mode and monitored the output but nothing found.
restarted all services but again no difference.
stoped md30-emu
stopped mmdvm_bridge
stopped analog_bridge_p25 and analog_bridge_dmr
restarted all services manually in seperate windows so I could monitor the output to the screen.

Results I am getting, 
If I key up on the P25 radio, I get nothing coming to any of the screen outputs, but can hear myself via another connected P25 Hotspot so I know the reflector is working OK
If I key up on DMR I can see all 3 screen outputs and can hear myself out of the P25 Radio.

Anyone have any idea where to start to look for this issue.

Ian (VK2HK)
 


Re: Allstarlink to Echolink showing an error??

Mike KB8JNM
 

Could you say a bit more on the conditions when you get this error?

Is it you connecting to your own node behind/inside  your nat ?

...mike/kb8jnm

On 1/4/2019 11:17 AM, jeff@... wrote:
When Connecting to an Echolink Node Number I receive this message on the console., But the echolink node "does" connect...
any idea what this error is and how to correct it??


Re: Dvswitch bridge help

Steve N4IRS
 

Where does it stop. That page has you look in several places. It's follow the data through the system.

On 1/4/2019 11:31 AM, Ke4tlc wrote:
The part where I key the radio to produce trafitr. 


Re: Dvswitch bridge help

Ke4tlc
 

The part where I key the radio to produce trafitr. 


Re: Dvswitch bridge help

Steve N4IRS
 

What is not working? Where does it stop?

On 1/4/2019 11:27 AM, Ke4tlc wrote:
Yes I used that document .  I did the checks and it looked to me it was correct.  I think it is something  I am missing. 


Re: Dvswitch bridge help

Ke4tlc
 

Yes I used that document .  I did the checks and it looked to me it was correct.  I think it is something  I am missing. 


Re: Dvswitch bridge help

Steve N4IRS
 

What are you trying to accomplish?
If you are using this document <https://docs.google.com/document/d/1eN50Csr29eAprBu7eKA0Bfa2XUcsXw5iktY1Ey-Qjkg/edit> At each major step you will check your work. Do not continue until you complete the check.

Steve N4IRS

On 1/4/2019 10:30 AM, Ke4tlc wrote:
I would like for someone to remote in to my system to try to help me  figure out where I went wrong .  I followed the steps  by steps.. I don't know where to begin to explain. 

My email is ke4tlc@...


Re: Allstarlink to Echolink showing an error??

Corey Dean N3FE <n3fe@...>
 

Any chance you are using the allow list in the echolink.conf file?  I know if I have the allow list turned on I can't make any outgoing echolink calls, but I can receive incoming.  If I comment out the allow line then it works fine in both directions.

Isn't this more of an allstar question than a DVswitch question?

Corey  N3FE


On Fri, Jan 4, 2019 at 11:17 AM <jeff@...> wrote:
When Connecting to an Echolink Node Number I receive this message on the console., But the echolink node "does" connect...
any idea what this error is and how to correct it??


Allstarlink to Echolink showing an error??

Jeff Wood
 

When Connecting to an Echolink Node Number I receive this message on the console., But the echolink node "does" connect...
any idea what this error is and how to correct it??


Dvswitch bridge help

Ke4tlc
 

I would like for someone to remote in to my system to try to help me  figure out where I went wrong .  I followed the steps  by steps.. I don't know where to begin to explain. 

My email is ke4tlc@.... 


Re: Potential Openbridge usage

Peter M0NWI
 

To confirm what Corey is saying on sizing, I have ~10 Moto repeaters, a few MMDVM via IPSC_Bridge, and a second IPSC_Bridge for hotspots, plus all the normal LAMP stuff for a web live monitor etc., my VM spec is below;



I have recently cleared the logs down though!


From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of Corey Dean N3FE <n3fe@...>
Sent: 04 January 2019 02:55
To: main@dvswitch.groups.io
Subject: Re: [DVSwitch] Potential Openbridge usage
 
I am using the minimal single core and 1 gig of ram with 3 different OB connections and many talkgroups at that, some repeaters, and a cbridge ipsc connection and The virtual machine is pretty much sitting idle.

Corey n3fe

On Thu, Jan 3, 2019 at 9:00 PM Bill N2WNS <n2wns.radio@...> wrote:
I'm looking to spin up 2 C-Bridges in two different geographic areas that will have different traffic needs. To ease administration on the upstream the BM/MARC providers, should I implement OB to get the TG traffic, then distribute the traffic from OB to the C-Bridges? What kind of processing power and memory would be required in a virtual environment for such an install?

Thanks, -Bill N2WNS


Re: Setting up DMRLink <-> KBLink #best_practices #dmrlink #hblink

Corey Dean N3FE <n3fe@...>
 

It sounds like you are pulling the main branch and not the ipsc-Bridge branch.

On Thu, Jan 3, 2019 at 11:02 PM Jason Johnston <kc5hwb@...> wrote:
As originally stated, not ALL of the files came down.  Some did, some did not.  Among those that did not were the *_Bridge files.  But the dmrlink-SAMPLE.cfg and such files all came down, along with the directories listed in the repo.

I just removed everything from the /opt folder and I am trying again now.


Re: Setting up DMRLink <-> KBLink #best_practices #dmrlink #hblink

Jason Johnston
 

I think I see what I did wrong and it worked this time.  Onward....


Re: Setting up DMRLink <-> KBLink #best_practices #dmrlink #hblink

Jason Johnston
 

As originally stated, not ALL of the files came down.  Some did, some did not.  Among those that did not were the *_Bridge files.  But the dmrlink-SAMPLE.cfg and such files all came down, along with the directories listed in the repo.

I just removed everything from the /opt folder and I am trying again now.


Re: C-Bridge to P25 Reflector Bridge

Michael KD5DFB
 

So it would look like this?

cbridge <-> ipsc_bridge <-> hb_confbridge <-> AB1 <-> AB2 <-> MMDM_bridge

Or I guess it could go like this?

cbridge <-> ipsc_bridge <-> hb_confbridge <-> MMDM_bridge  


On Thu, Jan 3, 2019 at 9:47 PM Steve N4IRS <szingman@...> wrote:
Since you already have a IPSC_Bridge <-> HB_Bridge built for feeding your MMDVM you may be able to add hb_confbridge. The get your MMDVM and MMDVM_Bridge connection from there.

On 1/3/19 10:43 PM, KD5DFB wrote:
Can I use confbridge_rules.py to limit it? 

On Thu, Jan 3, 2019 at 9:39 PM Steve N4IRS <szingman@...> wrote:
Can't that be controlled at the c-Bridge?

On 1/3/19 10:36 PM, KD5DFB wrote:
Still looking for some help or a point in the right direction. 

I am wanting to only allow only certain timeslot/group IDs, etc. to pass between the cbridge and analog_bridge



Re: Setting up DMRLink <-> KBLink #best_practices #dmrlink #hblink

Steve N4IRS
 

So, which was it? No files came down or 2/3 of the repo? Have you looked at the branches in question?

On 1/3/19 10:58 PM, Jason Johnston wrote:
It cloned about 2/3 of the files listed in the github repositories. No errors. I assumed it was by design. 

On Thu, Jan 3, 2019, 9:54 PM Steve N4IRS <szingman@...> wrote:
no error message? no nothing? Don't know what to tell ya. google cloning a git branch.


On 1/3/19 10:51 PM, Jason Johnston wrote:
Nope. I put them in the /opt folder, there were no subdirectories. 

On Thu, Jan 3, 2019, 9:50 PM Steve N4IRS <szingman@...> wrote:
Did dmrlink and hblink directories already exist?

On 1/3/19 10:45 PM, Jason Johnston wrote:
I did that already. Not all files came down. 

On Thu, Jan 3, 2019, 9:28 PM Steve N4IRS <szingman@...> wrote:
Bad idea. Get the whole repo(s)

git clone -b IPSC_Bridge https://github.com/n0mjs710/DMRlink.git
git clone -b HB_Bridge https://github.com/n0mjs710/HBlink


On 1/3/19 10:25 PM, Jason Johnston wrote:
I understood Steve's comments and ran that command, which worked.  /var/log did exist, but the dmrlink dir underneath it didn't.  I have successfully connected it to my cbridge now by running the dmrlink.py file.

Upon running the git clone command for both directories, it appears that the HBlink_Bridge and DMRlink_Bridge files didn't pull down.  I ran a wget cmd and pulled the .cfg and .py files from the github folders.  Tomorrow I will work to configure those.

--
73 de
Jason - KC5HWB

--
73 de
Jason - KC5HWB

--
73 de
Jason - KC5HWB

7181 - 7200 of 9925