Date   

Re: DMR Master Disconnects

Steve N4IRS
 

John,
As Curt explained the install set up MMDVM_Bridge (and others) to start at boot. There will be times when you need to run in the foreground and all you need to do is make sure you are the only running copy unless you are running a more complex bridge.

systemctl has 6 commands you will want to know off the top of your head and quite a few more that -h or man systemctl will show you.

systemctl start mmdvm_bridge    # Start the mmdvm_bridge service
systemctl status mmdvm_bridge  # check the status of the mmdvm_bridge service. Is it running? is it enabled? any errors?
systemctl stop mmdvm_bridge     # stop the service IF it is running
systemctl restart mmdvm_bridge # restart the service (will also start it if not running) good for re-reading the config files.
systemctl enable mmdvm_bridge # setup the service to start at boot
systemctl disable mmdvm_bridge # stop the service from running at boot.

The 3 big ones for you with a running bridge are stop, start and status. Always check the status before running in the foreground.

Hope this helps,
Steve N4IRS 

On 7/24/19 5:03 PM, John - WB5NFC wrote:
Gentleman, thank you for identifying the source of my self-inflicted headache! Now that only one instance is running, there are no login/logout errors.

In trying to remember when or how I got into this twofer mess, I remember seeing the list of useful commands at the end of the setup document and trying them out. I just "assumed" anything started would reset after a boot. That little word sure gets people in trouble... thanks again, guys.


Re: DMR Master Disconnects

John - WB5NFC <wb5nfc@...>
 

Gentleman, thank you for identifying the source of my self-inflicted headache! Now that only one instance is running, there are no login/logout errors.

In trying to remember when or how I got into this twofer mess, I remember seeing the list of useful commands at the end of the setup document and trying them out. I just "assumed" anything started would reset after a boot. That little word sure gets people in trouble... thanks again, guys.


Re: DMR Master Disconnects

Curt Hart <curtg49@...>
 

John,
it's starting at boot because the service is enabled. if you don't want it to start at boot systemctl disable mmdvm_bridge or after you've made changes systemctl restart mmdvm_bridge.
See systemctl --help
Hope this helps,
Curtis - N9INK

On Wednesday, July 24, 2019, 3:14:10 PM CDT, John - WB5NFC <wb5nfc@...> wrote:


I believe you're right on target, as usual! Time permitting,  educate me a little (or a LOT), please...

I didn't understand what I was seeing with the ps ax | grep MMDVM command.

root@WB5NFC-2186:/opt/MMDVM_Bridge#  ps ax | grep MMDVM
  668 ?        Ss     0:01 /opt/MMDVM_Bridge/MMDVM_Bridge /opt/MMDVM_Bridge/MMDVM_Bridge.ini
 1265 pts/0    S+     0:00 grep MMDVM

So I ran systemctl status mmdvm_bridge

● mmdvm_bridge.service - MMDVM_Bridge Service
   Loaded: loaded (/lib/systemd/system/mmdvm_bridge.service; enabled; vendor preset: enabled
   Active: active (running) since Wed 2019-07-24 13:51:14 CDT; 34min ago
 Main PID: 661 (MMDVM_Bridge)
   CGroup: /system.slice/mmdvm_bridge.service
           └─661 /opt/MMDVM_Bridge/MMDVM_Bridge /opt/MMDVM_Bridge/MMDVM_Bridge.ini

Which I think... tells me, yes dummy, it's already running and there's your problem.  How I started it at boot and now how I keep it from starting at every boot (while testing) are questions I can't answer.....


Re: DMR Master Disconnects

John - WB5NFC <wb5nfc@...>
 

I believe you're right on target, as usual! Time permitting,  educate me a little (or a LOT), please...

I didn't understand what I was seeing with the ps ax | grep MMDVM command.

root@WB5NFC-2186:/opt/MMDVM_Bridge#  ps ax | grep MMDVM
  668 ?        Ss     0:01 /opt/MMDVM_Bridge/MMDVM_Bridge /opt/MMDVM_Bridge/MMDVM_Bridge.ini
 1265 pts/0    S+     0:00 grep MMDVM

So I ran systemctl status mmdvm_bridge

● mmdvm_bridge.service - MMDVM_Bridge Service
   Loaded: loaded (/lib/systemd/system/mmdvm_bridge.service; enabled; vendor preset: enabled
   Active: active (running) since Wed 2019-07-24 13:51:14 CDT; 34min ago
 Main PID: 661 (MMDVM_Bridge)
   CGroup: /system.slice/mmdvm_bridge.service
           └─661 /opt/MMDVM_Bridge/MMDVM_Bridge /opt/MMDVM_Bridge/MMDVM_Bridge.ini

Which I think... tells me, yes dummy, it's already running and there's your problem.  How I started it at boot and now how I keep it from starting at every boot (while testing) are questions I can't answer.....


Re: #hblink #hblink

Aaron Groover
 

I’ve heard nothing out of BM about the link. So if BM approves it I won’t do TGIF




Respectfully,

Aaron Groover
(610) 379-6148
K3ALG@...


From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of Corey Dean N3FE <n3fe@...>
Sent: Wednesday, July 24, 2019 3:16:55 PM
To: main@dvswitch.groups.io <main@dvswitch.groups.io>
Subject: Re: [DVSwitch] #hblink
 
I really hope this isn’t the ysf reflector link you submitted to the bm support team!  We do not and will not crosslink to TGIF from BM.

Corey n3fe

On Wed, Jul 24, 2019 at 2:43 PM <k3alg@...> wrote:
So new to this whole hblink thing. However i Have a YSF Reflector that i want to bridge to TGIF. Can someone please tell me the command prompts and how to set it up? Thanks!


Re: #hblink #hblink

Corey Dean N3FE <n3fe@...>
 

I really hope this isn’t the ysf reflector link you submitted to the bm support team!  We do not and will not crosslink to TGIF from BM.

Corey n3fe

On Wed, Jul 24, 2019 at 2:43 PM <k3alg@...> wrote:
So new to this whole hblink thing. However i Have a YSF Reflector that i want to bridge to TGIF. Can someone please tell me the command prompts and how to set it up? Thanks!


Re: #hblink #hblink

Steve N4IRS
 

Aaron,
YSF2DMR is not part of the DVSwitch family. You should go here: <https://github.com/juribeparada/MMDVM_CM>

73, Steve N4IRS

On 7/24/2019 2:53 PM, Aaron Groover wrote:
Sorry Alec lol Ill try to make it more not confusing. I already created the YSF reflector its already up and running "PA 6 County" so now i want to bridge it with a TGIF TG with YSF2DMR. However i do not know the command prompts how to get it started. So if you know them step by step that would be great

Aaron


#hblink #hblink

Aaron Groover
 

Sorry Alec lol Ill try to make it more not confusing. I already created the YSF reflector its already up and running "PA 6 County" so now i want to bridge it with a TGIF TG with YSF2DMR. However i do not know the command prompts how to get it started. So if you know them step by step that would be great

Aaron


Re: #hblink #hblink

Aaron Groover
 

The reflector is up on YSF I want to bridge it to TGIF




Respectfully,

Aaron Groover
(610) 379-6148
K3ALG@...


From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of Alec-N1AJW <alec.wasserman@...>
Sent: Wednesday, July 24, 2019 2:46:47 PM
To: main@DVSwitch.groups.io <main@DVSwitch.groups.io>
Subject: Re: [DVSwitch] #hblink
 
https://register.ysfreflector.de/installation


make sure not to bridge it to 31665.  outside bridges arent allowed per Robert.

Alec
N1AJW


Re: #hblink #hblink

Alec-N1AJW
 

https://register.ysfreflector.de/installation


make sure not to bridge it to 31665.  outside bridges arent allowed per Robert.

Alec
N1AJW


Re: DMR Master Disconnects

Steve N4IRS
 

John,
Thanks for that. I don't see any issue. Thinking about your description, if you are running MMDVM_Bridge in the foreground, are you sure it's not ALSO running in background?
Before you start MB in the foreground:
ps ax | grep MMDVM

Steve

On 7/24/2019 1:47 PM, John - WB5NFC wrote:
[DMR Network]
Enable=1
Address=3102.repeater.net
Port=62031
Jitter=360
Local=62032
Password=passw0rd
Slot1=1
Slot2=1
Debug=0

[DMR]
Enable=1
ColorCode=1
EmbeddedLCOnly=1
DumpTAData=0


#hblink #hblink

Aaron Groover
 

So new to this whole hblink thing. However i Have a YSF Reflector that i want to bridge to TGIF. Can someone please tell me the command prompts and how to set it up? Thanks!


Re: DMR Master Disconnects

John - WB5NFC <wb5nfc@...>
 

Interesting.... thanks, Mark. I've made no changes in configs today. Didn't even log in until late this morning and that was just to get the info Steve requested. I had saved the Connect / Disconnect messages earlier in the week.


Re: DMR Master Disconnects

Mark N2NUO <n2nuo@...>
 

I just looked at the logs on Master 3102 and see your connection and sudden disconnects. I see no reason in the server for the disconnects, earlier in the day I see you have the incorrect password setup, but after that you connected and then soon after, it disconnects.
A little insight from the Master server side.
Mark

On 7/24/19 1:47 PM, John - WB5NFC wrote:
[DMR Network]
Enable=1
Address=3102.repeater.net
Port=62031
Jitter=360
Local=62032
Password=passw0rd
Slot1=1
Slot2=1
Debug=0

[DMR]
Enable=1
ColorCode=1
EmbeddedLCOnly=1
DumpTAData=0


Re: DMR Master Disconnects

John - WB5NFC <wb5nfc@...>
 

[DMR Network]
Enable=1
Address=3102.repeater.net
Port=62031
Jitter=360
Local=62032
Password=passw0rd
Slot1=1
Slot2=1
Debug=0

[DMR]
Enable=1
ColorCode=1
EmbeddedLCOnly=1
DumpTAData=0


Re: DMR Master Disconnects

Steve N4IRS
 

John,
As a start, Please show the [DMR] and [DMR Network] stanzas from MMDVM_Bridge.ini

Steve N4IRS

On 7/24/2019 12:28 PM, John - WB5NFC wrote:
I'm making a first run at installing ASL to DMR Bridge on a Rpi 3B+ with the latest ASL image. Install proceedes normally until I run MMDVM_Bridge in the foreground. First logon to the master server is good, but I get disconnected after about a minute. Then the cycle of connects and disconnects continues thereafter. Can someone point me in the right direction for determining the source of this behavior? Thanks in advance! John / WB5NFC

M: 2019-07-21 21:20:58.069 DMR, Setting [DMR] Address -> 127.0.0.1
M: 2019-07-21 21:20:58.069 DMR, Setting [DMR] TXPort -> 31100
M: 2019-07-21 21:20:58.069 DMR, Setting [DMR] RXPort -> 31103
M: 2019-07-21 21:20:58.069 DMR, Setting [DMR] Slot -> 2
M: 2019-07-21 21:20:58.069 DMR, Transmitting on 127.0.0.1:31100 and listening on port 31103.  Result = 1
M: 2019-07-21 21:20:58.069 MMDVM_Bridge-20180423 is running
D: 2019-07-21 21:21:08.163 DMR, Sending authorisation
D: 2019-07-21 21:21:08.260 DMR, Sending configuration
M: 2019-07-21 21:21:08.363 DMR, Logged into the master successfully
W: 2019-07-21 21:22:08.475 DMR, Login to the master has failed, retrying login ...
E: 2019-07-21 21:23:08.480 DMR, Connection to the master has timed out, retrying connection
M: 2019-07-21 21:23:08.480 DMR, Closing DMR Network
M: 2019-07-21 21:23:08.480 DMR, Opening DMR Network
D: 2019-07-21 21:23:18.587 DMR, Sending authorisation
D: 2019-07-21 21:23:18.685 DMR, Sending configuration
M: 2019-07-21 21:23:18.782 DMR, Logged into the master successfully
W: 2019-07-21 21:24:18.892 DMR, Login to the master has failed, retrying login ...
E: 2019-07-21 21:25:18.894 DMR, Connection to the master has timed out, retrying connection
M: 2019-07-21 21:25:18.895 DMR, Closing DMR Network
M: 2019-07-21 21:25:18.895 DMR, Opening DMR Network
D: 2019-07-21 21:25:28.987 DMR, Sending authorisation
D: 2019-07-21 21:25:29.084 DMR, Sending configuration
M: 2019-07-21 21:25:29.181 DMR, Logged into the master successfully


DMR Master Disconnects

John - WB5NFC <wb5nfc@...>
 

I'm making a first run at installing ASL to DMR Bridge on a Rpi 3B+ with the latest ASL image. Install proceedes normally until I run MMDVM_Bridge in the foreground. First logon to the master server is good, but I get disconnected after about a minute. Then the cycle of connects and disconnects continues thereafter. Can someone point me in the right direction for determining the source of this behavior? Thanks in advance! John / WB5NFC

M: 2019-07-21 21:20:58.069 DMR, Setting [DMR] Address -> 127.0.0.1
M: 2019-07-21 21:20:58.069 DMR, Setting [DMR] TXPort -> 31100
M: 2019-07-21 21:20:58.069 DMR, Setting [DMR] RXPort -> 31103
M: 2019-07-21 21:20:58.069 DMR, Setting [DMR] Slot -> 2
M: 2019-07-21 21:20:58.069 DMR, Transmitting on 127.0.0.1:31100 and listening on port 31103.  Result = 1
M: 2019-07-21 21:20:58.069 MMDVM_Bridge-20180423 is running
D: 2019-07-21 21:21:08.163 DMR, Sending authorisation
D: 2019-07-21 21:21:08.260 DMR, Sending configuration
M: 2019-07-21 21:21:08.363 DMR, Logged into the master successfully
W: 2019-07-21 21:22:08.475 DMR, Login to the master has failed, retrying login ...
E: 2019-07-21 21:23:08.480 DMR, Connection to the master has timed out, retrying connection
M: 2019-07-21 21:23:08.480 DMR, Closing DMR Network
M: 2019-07-21 21:23:08.480 DMR, Opening DMR Network
D: 2019-07-21 21:23:18.587 DMR, Sending authorisation
D: 2019-07-21 21:23:18.685 DMR, Sending configuration
M: 2019-07-21 21:23:18.782 DMR, Logged into the master successfully
W: 2019-07-21 21:24:18.892 DMR, Login to the master has failed, retrying login ...
E: 2019-07-21 21:25:18.894 DMR, Connection to the master has timed out, retrying connection
M: 2019-07-21 21:25:18.895 DMR, Closing DMR Network
M: 2019-07-21 21:25:18.895 DMR, Opening DMR Network
D: 2019-07-21 21:25:28.987 DMR, Sending authorisation
D: 2019-07-21 21:25:29.084 DMR, Sending configuration
M: 2019-07-21 21:25:29.181 DMR, Logged into the master successfully


Re: Can work audio from Mic In or Inline Sound for USRPAudio.py with vox control and convert to DMR?

EA5GVK Joaquin
 

Great new. Many thanks


El mar., 23 jul. 2019 a las 23:19, Steve N4IRS (<szingman@...>) escribió:
We have something in the works. It will be a little while....

On 7/23/19 5:13 PM, EA5GVK Joaquin wrote:
Show can do?
Many thx


Re: About mode YSFN in dvswicht mobile.

Mike Zingman - N4IRR
 

You can add the ip:port to your macro menu. 
It will work just fine till I do the database upload changes. 


Re: Can work audio from Mic In or Inline Sound for USRPAudio.py with vox control and convert to DMR?

Steve N4IRS
 

We have something in the works. It will be a little while....

On 7/23/19 5:13 PM, EA5GVK Joaquin wrote:
Show can do?
Many thx

5321 - 5340 of 9795