Date   

Re: Jackhammer Sound

Steve N4IRS
 

Your best bet is to try to troubleshoot md380-emu since it will sound better then the built in OP25. (for DMR, YSFn, NXDN and definitive D-Star)

On 8/2/19 4:39 PM, Jeff Lehman, N8ACL via Groups.Io wrote:
ooops.....Lemme try again....

That did it....I stopped the md380-emu and disabled it in the bridge. it is working now.

Thanks Steve....

Jeff, N8ACL

On 8/2/19 4:26 PM, Steve N4IRS wrote:
Did you disable use emulator in AB.ini?

On 8/2/19 4:09 PM, Jeff Lehman, N8ACL via Groups.Io wrote:
I stopped it and still got the jackhammer.....

I checked status of the Emulator....

systemctl status md380-emu
* md380-emu.service - MD-380 Emulator Service
   Loaded: loaded (/lib/systemd/system/md380-emu.service; enabled; vendor preset: enabled)
   Active: activating (auto-restart) (Result: exit-code) since Fri 2019-08-02 20:09:04 UTC; 209ms ago
  Process: 673 ExecStart=/opt/md380-emu/md380-emu -S 2470 (code=exited, status=203/EXEC)
 Main PID: 673 (code=exited, status=203/EXEC)
md380-emu.service: Failed with result 'exit-code'.

On 8/2/19 4:01 PM, Steve N4IRS wrote:
That would be my guess. Turn off the emulator and retest.

On 8/2/19 3:59 PM, Jeff Lehman, N8ACL via Groups.Io wrote:
HI all,

I just did an install of another bridge and I am getting this weird sound. Background....

I am building a DMR<--> ASL bridge on a VM. I have one system on one VM and the Bridge on another. I am using USRP to connect from the main ASL system to the VM/Bridge. I have done this before with a YSF reflector, using USRP to connect to AB on a second VM with the YSF reflector running on it with MB.

I have AB and MB on the bridge VM and have USRP connected properly. When I key up I can see the traffic flow in the right directions.

Problem is, I get this jackhammer, almost grinding sound when I key up from Either end. If i key from ASL, I have the grinding on DMR. Same thing if I key from the radio going to ASL.

This has happened before in the past and I was able to reload the system from a snapshot and the problem went away. My gut says it's something maybe with md380-emu?

Thoughts?

Jeff, N8ACL





Re: Jackhammer Sound

Jeff Lehman, N8ACL
 

ooops.....Lemme try again....

That did it....I stopped the md380-emu and disabled it in the bridge. it is working now.

Thanks Steve....

Jeff, N8ACL

On 8/2/19 4:26 PM, Steve N4IRS wrote:
Did you disable use emulator in AB.ini?

On 8/2/19 4:09 PM, Jeff Lehman, N8ACL via Groups.Io wrote:
I stopped it and still got the jackhammer.....

I checked status of the Emulator....

systemctl status md380-emu
* md380-emu.service - MD-380 Emulator Service
   Loaded: loaded (/lib/systemd/system/md380-emu.service; enabled; vendor preset: enabled)
   Active: activating (auto-restart) (Result: exit-code) since Fri 2019-08-02 20:09:04 UTC; 209ms ago
  Process: 673 ExecStart=/opt/md380-emu/md380-emu -S 2470 (code=exited, status=203/EXEC)
 Main PID: 673 (code=exited, status=203/EXEC)
md380-emu.service: Failed with result 'exit-code'.

On 8/2/19 4:01 PM, Steve N4IRS wrote:
That would be my guess. Turn off the emulator and retest.

On 8/2/19 3:59 PM, Jeff Lehman, N8ACL via Groups.Io wrote:
HI all,

I just did an install of another bridge and I am getting this weird sound. Background....

I am building a DMR<--> ASL bridge on a VM. I have one system on one VM and the Bridge on another. I am using USRP to connect from the main ASL system to the VM/Bridge. I have done this before with a YSF reflector, using USRP to connect to AB on a second VM with the YSF reflector running on it with MB.

I have AB and MB on the bridge VM and have USRP connected properly. When I key up I can see the traffic flow in the right directions.

Problem is, I get this jackhammer, almost grinding sound when I key up from Either end. If i key from ASL, I have the grinding on DMR. Same thing if I key from the radio going to ASL.

This has happened before in the past and I was able to reload the system from a snapshot and the problem went away. My gut says it's something maybe with md380-emu?

Thoughts?

Jeff, N8ACL



--
Jeff Lehman, N8ACL
E-mail: N8ACL@icloud.com
Hamshack Hotline: 4218

Webmaster
Hamilton County ARPSC
http://www.hamcoarpsc.org
E-mail: info@hamcoarpsc.org
Phone: 513-452-6480

Technical Director
World Wide Amateur Radio Guild
https://hamradiohub.com/
E-Mail: n8acl@hamradiohub.me


Re: Jackhammer Sound

Steve N4IRS
 

Did you disable use emulator in AB.ini?

On 8/2/19 4:09 PM, Jeff Lehman, N8ACL via Groups.Io wrote:
I stopped it and still got the jackhammer.....

I checked status of the Emulator....

systemctl status md380-emu
* md380-emu.service - MD-380 Emulator Service
   Loaded: loaded (/lib/systemd/system/md380-emu.service; enabled; vendor preset: enabled)
   Active: activating (auto-restart) (Result: exit-code) since Fri 2019-08-02 20:09:04 UTC; 209ms ago
  Process: 673 ExecStart=/opt/md380-emu/md380-emu -S 2470 (code=exited, status=203/EXEC)
 Main PID: 673 (code=exited, status=203/EXEC)
md380-emu.service: Failed with result 'exit-code'.

On 8/2/19 4:01 PM, Steve N4IRS wrote:
That would be my guess. Turn off the emulator and retest.

On 8/2/19 3:59 PM, Jeff Lehman, N8ACL via Groups.Io wrote:
HI all,

I just did an install of another bridge and I am getting this weird sound. Background....

I am building a DMR<--> ASL bridge on a VM. I have one system on one VM and the Bridge on another. I am using USRP to connect from the main ASL system to the VM/Bridge. I have done this before with a YSF reflector, using USRP to connect to AB on a second VM with the YSF reflector running on it with MB.

I have AB and MB on the bridge VM and have USRP connected properly. When I key up I can see the traffic flow in the right directions.

Problem is, I get this jackhammer, almost grinding sound when I key up from Either end. If i key from ASL, I have the grinding on DMR. Same thing if I key from the radio going to ASL.

This has happened before in the past and I was able to reload the system from a snapshot and the problem went away. My gut says it's something maybe with md380-emu?

Thoughts?

Jeff, N8ACL



Re: Jackhammer Sound

Jeff Lehman, N8ACL
 

I stopped it and still got the jackhammer.....

I checked status of the Emulator....

systemctl status md380-emu
* md380-emu.service - MD-380 Emulator Service
   Loaded: loaded (/lib/systemd/system/md380-emu.service; enabled; vendor preset: enabled)
   Active: activating (auto-restart) (Result: exit-code) since Fri 2019-08-02 20:09:04 UTC; 209ms ago
  Process: 673 ExecStart=/opt/md380-emu/md380-emu -S 2470 (code=exited, status=203/EXEC)
 Main PID: 673 (code=exited, status=203/EXEC)
md380-emu.service: Failed with result 'exit-code'.

On 8/2/19 4:01 PM, Steve N4IRS wrote:
That would be my guess. Turn off the emulator and retest.

On 8/2/19 3:59 PM, Jeff Lehman, N8ACL via Groups.Io wrote:
HI all,

I just did an install of another bridge and I am getting this weird sound. Background....

I am building a DMR<--> ASL bridge on a VM. I have one system on one VM and the Bridge on another. I am using USRP to connect from the main ASL system to the VM/Bridge. I have done this before with a YSF reflector, using USRP to connect to AB on a second VM with the YSF reflector running on it with MB.

I have AB and MB on the bridge VM and have USRP connected properly. When I key up I can see the traffic flow in the right directions.

Problem is, I get this jackhammer, almost grinding sound when I key up from Either end. If i key from ASL, I have the grinding on DMR. Same thing if I key from the radio going to ASL.

This has happened before in the past and I was able to reload the system from a snapshot and the problem went away. My gut says it's something maybe with md380-emu?

Thoughts?

Jeff, N8ACL

--
Jeff Lehman, N8ACL
E-mail: N8ACL@icloud.com
Hamshack Hotline: 4218

Webmaster
Hamilton County ARPSC
http://www.hamcoarpsc.org
E-mail: info@hamcoarpsc.org
Phone: 513-452-6480

Technical Director
World Wide Amateur Radio Guild
https://hamradiohub.com/
E-Mail: n8acl@hamradiohub.me


Re: Jackhammer Sound

Steve N4IRS
 

That would be my guess. Turn off the emulator and retest.

On 8/2/19 3:59 PM, Jeff Lehman, N8ACL via Groups.Io wrote:
HI all,

I just did an install of another bridge and I am getting this weird sound. Background....

I am building a DMR<--> ASL bridge on a VM. I have one system on one VM and the Bridge on another. I am using USRP to connect from the main ASL system to the VM/Bridge. I have done this before with a YSF reflector, using USRP to connect to AB on a second VM with the YSF reflector running on it with MB.

I have AB and MB on the bridge VM and have USRP connected properly. When I key up I can see the traffic flow in the right directions.

Problem is, I get this jackhammer, almost grinding sound when I key up from Either end. If i key from ASL, I have the grinding on DMR. Same thing if I key from the radio going to ASL.

This has happened before in the past and I was able to reload the system from a snapshot and the problem went away. My gut says it's something maybe with md380-emu?

Thoughts?

Jeff, N8ACL


Jackhammer Sound

Jeff Lehman, N8ACL
 

HI all,

I just did an install of another bridge and I am getting this weird sound. Background....

I am building a DMR<--> ASL bridge on a VM. I have one system on one VM and the Bridge on another. I am using USRP to connect from the main ASL system to the VM/Bridge. I have done this before with a YSF reflector, using USRP to connect to AB on a second VM with the YSF reflector running on it with MB.

I have AB and MB on the bridge VM and have USRP connected properly. When I key up I can see the traffic flow in the right directions.

Problem is, I get this jackhammer, almost grinding sound when I key up from Either end. If i key from ASL, I have the grinding on DMR. Same thing if I key from the radio going to ASL.

This has happened before in the past and I was able to reload the system from a snapshot and the problem went away. My gut says it's something maybe with md380-emu?

Thoughts?

Jeff, N8ACL

--
Jeff Lehman, N8ACL
E-mail: N8ACL@icloud.com
Hamshack Hotline: 4218

Webmaster
Hamilton County ARPSC
http://www.hamcoarpsc.org
E-mail: info@hamcoarpsc.org
Phone: 513-452-6480

Technical Director
World Wide Amateur Radio Guild
https://hamradiohub.com/
E-Mail: n8acl@hamradiohub.me


Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Steve N4IRS
 

Chris,
I just tested your call and DMR ID on a VM. I have no problem logging in or staying logged in. I think it's time for you to start over fresh a fresh install.
The first thing you need to do after setting up a new VM is to make sure you have a ssh client and a e-mail clinet on the machine you are using to connect to the VM.
Cell phone pictures or transcribing by hand will not work if you are asking for help. I understand this may seem harsh but this trhread has 45 messages in it and I know we have too many working bridges for what you are experiencing to be a issue in MMDVM_Bridge. Please setup a environment where we can help you.

Steve N4IRS

On 8/2/19 1:02 AM, Chris K7AZ via Groups.Io wrote:
62030 in MMDVM_Bridge doesnt connect at all... 



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: "Chris K7AZ via Groups.Io" <kilo7alphazulu@...>
Date: 8/1/19 20:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

I'll give that a try.  Tnx.   



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Adrian Fewster <vk4tux@...>
Date: 8/1/19 20:33 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Have you tried port 62030 instead of 62031 ?

On 2/8/19 1:12 pm, Chris K7AZ via Groups.Io wrote:
The same problem persists across 4 different Masters.  

I don't have this email on the laptop being used to TV into the VM server across town.  

I'll hand transcribe as needed to avoid sending pictures.  



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 19:06 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Chris,
You have a problem with your connection to the Master, simple as that. Have you tried another Master? PLEASE learn to capture the test and paste it into a e-mail. No more cell phone pictures.

On 8/1/19 10:00 PM, Chris K7AZ via Groups.Io wrote:
Here is what I'm seeing.  
A minute after "Logged into master successfully" it says "Login to the master has failed, retrying connection".
Screen shot attached.



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 16:23 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Changing the password is not going to do you any good. The password for US Masters is "passw0rd" It's either logging in or not. Are you really sure it's ever logging in? This is what a successful login looks like:

M: 2019-08-01 23:20:21.455 MMDVM_Bridge-20180423 is running
D: 2019-08-01 23:20:31.493 DMR, Sending authorisation
D: 2019-08-01 23:20:31.540 DMR, Sending configuration
M: 2019-08-01 23:20:31.586 DMR, Logged into the master successfully
 

On 8/1/19 6:40 PM, Chris K7AZ via Groups.Io wrote:
When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric




Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Adrian Fewster <vk4tux@...>
 

Ok, just wondered, as that has worked where 62031 didn't in other situations I have seen.

Check you have no other config sections missing, compare with another source config template to check.

Try a friends id with consent to test also if you can.

Last check router & system firewall / port access that may interrupt the connect negotiation.



On 2/8/19 3:02 pm, Chris K7AZ via Groups.Io wrote:
62030 in MMDVM_Bridge doesnt connect at all... 



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: "Chris K7AZ via Groups.Io" <kilo7alphazulu@...>
Date: 8/1/19 20:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

I'll give that a try.  Tnx.   



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Adrian Fewster <vk4tux@...>
Date: 8/1/19 20:33 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Have you tried port 62030 instead of 62031 ?

On 2/8/19 1:12 pm, Chris K7AZ via Groups.Io wrote:
The same problem persists across 4 different Masters.  

I don't have this email on the laptop being used to TV into the VM server across town.  

I'll hand transcribe as needed to avoid sending pictures.  



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 19:06 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Chris,
You have a problem with your connection to the Master, simple as that. Have you tried another Master? PLEASE learn to capture the test and paste it into a e-mail. No more cell phone pictures.

On 8/1/19 10:00 PM, Chris K7AZ via Groups.Io wrote:
Here is what I'm seeing.  
A minute after "Logged into master successfully" it says "Login to the master has failed, retrying connection".
Screen shot attached.



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 16:23 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Changing the password is not going to do you any good. The password for US Masters is "passw0rd" It's either logging in or not. Are you really sure it's ever logging in? This is what a successful login looks like:

M: 2019-08-01 23:20:21.455 MMDVM_Bridge-20180423 is running
D: 2019-08-01 23:20:31.493 DMR, Sending authorisation
D: 2019-08-01 23:20:31.540 DMR, Sending configuration
M: 2019-08-01 23:20:31.586 DMR, Logged into the master successfully
 

On 8/1/19 6:40 PM, Chris K7AZ via Groups.Io wrote:
When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric



Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Chris K7AZ
 

62030 in MMDVM_Bridge doesnt connect at all... 



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: "Chris K7AZ via Groups.Io" <kilo7alphazulu@...>
Date: 8/1/19 20:53 (GMT-08:00)
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

I'll give that a try.  Tnx.   



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Adrian Fewster <vk4tux@...>
Date: 8/1/19 20:33 (GMT-08:00)
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Have you tried port 62030 instead of 62031 ?

On 2/8/19 1:12 pm, Chris K7AZ via Groups.Io wrote:
The same problem persists across 4 different Masters.  

I don't have this email on the laptop being used to TV into the VM server across town.  

I'll hand transcribe as needed to avoid sending pictures.  



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 19:06 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Chris,
You have a problem with your connection to the Master, simple as that. Have you tried another Master? PLEASE learn to capture the test and paste it into a e-mail. No more cell phone pictures.

On 8/1/19 10:00 PM, Chris K7AZ via Groups.Io wrote:
Here is what I'm seeing.  
A minute after "Logged into master successfully" it says "Login to the master has failed, retrying connection".
Screen shot attached.



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 16:23 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Changing the password is not going to do you any good. The password for US Masters is "passw0rd" It's either logging in or not. Are you really sure it's ever logging in? This is what a successful login looks like:

M: 2019-08-01 23:20:21.455 MMDVM_Bridge-20180423 is running
D: 2019-08-01 23:20:31.493 DMR, Sending authorisation
D: 2019-08-01 23:20:31.540 DMR, Sending configuration
M: 2019-08-01 23:20:31.586 DMR, Logged into the master successfully
 

On 8/1/19 6:40 PM, Chris K7AZ via Groups.Io wrote:
When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric



Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Chris K7AZ
 

310689107




Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 20:53 (GMT-08:00)
To: main@dvswitch.groups.io
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

What DMR I'd are you using to connect?

Sent via smoke signal (AT&T)


From: main@... <main@DVSwitch.groups.io> on behalf of Chris K7AZ via Groups.Io <kilo7alphazulu@...>
Sent: Thursday, August 1, 2019 11:12:39 PM
To: main@DVSwitch.groups.io <main@DVSwitch.groups.io>
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge
 
The same problem persists across 4 different Masters.  

I don't have this email on the laptop being used to TV into the VM server across town.  

I'll hand transcribe as needed to avoid sending pictures  



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 19:06 (GMT-08:00)
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Chris,
You have a problem with your connection to the Master, simple as that. Have you tried another Master? PLEASE learn to capture the test and paste it into a e-mail. No more cell phone pictures.

On 8/1/19 10:00 PM, Chris K7AZ via Groups.Io wrote:
Here is what I'm seeing.  
A minute after "Logged into master successfully" it says "Login to the master has failed, retrying connection".
Screen shot attached.



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 16:23 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Changing the password is not going to do you any good. The password for US Masters is "passw0rd" It's either logging in or not. Are you really sure it's ever logging in? This is what a successful login looks like:

M: 2019-08-01 23:20:21.455 MMDVM_Bridge-20180423 is running
D: 2019-08-01 23:20:31.493 DMR, Sending authorisation
D: 2019-08-01 23:20:31.540 DMR, Sending configuration
M: 2019-08-01 23:20:31.586 DMR, Logged into the master successfully
 

On 8/1/19 6:40 PM, Chris K7AZ via Groups.Io wrote:
When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric



Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Chris K7AZ
 

I'll give that a try.  Tnx.   



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Adrian Fewster <vk4tux@...>
Date: 8/1/19 20:33 (GMT-08:00)
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Have you tried port 62030 instead of 62031 ?

On 2/8/19 1:12 pm, Chris K7AZ via Groups.Io wrote:
The same problem persists across 4 different Masters.  

I don't have this email on the laptop being used to TV into the VM server across town.  

I'll hand transcribe as needed to avoid sending pictures.  



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 19:06 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Chris,
You have a problem with your connection to the Master, simple as that. Have you tried another Master? PLEASE learn to capture the test and paste it into a e-mail. No more cell phone pictures.

On 8/1/19 10:00 PM, Chris K7AZ via Groups.Io wrote:
Here is what I'm seeing.  
A minute after "Logged into master successfully" it says "Login to the master has failed, retrying connection".
Screen shot attached.



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 16:23 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Changing the password is not going to do you any good. The password for US Masters is "passw0rd" It's either logging in or not. Are you really sure it's ever logging in? This is what a successful login looks like:

M: 2019-08-01 23:20:21.455 MMDVM_Bridge-20180423 is running
D: 2019-08-01 23:20:31.493 DMR, Sending authorisation
D: 2019-08-01 23:20:31.540 DMR, Sending configuration
M: 2019-08-01 23:20:31.586 DMR, Logged into the master successfully
 

On 8/1/19 6:40 PM, Chris K7AZ via Groups.Io wrote:
When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric



Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Steve N4IRS
 

What DMR I'd are you using to connect?

Sent via smoke signal (AT&T)


From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of Chris K7AZ via Groups.Io <kilo7alphazulu@...>
Sent: Thursday, August 1, 2019 11:12:39 PM
To: main@DVSwitch.groups.io <main@DVSwitch.groups.io>
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge
 
The same problem persists across 4 different Masters.  

I don't have this email on the laptop being used to TV into the VM server across town.  

I'll hand transcribe as needed to avoid sending pictures.  



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 19:06 (GMT-08:00)
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Chris,
You have a problem with your connection to the Master, simple as that. Have you tried another Master? PLEASE learn to capture the test and paste it into a e-mail. No more cell phone pictures.

On 8/1/19 10:00 PM, Chris K7AZ via Groups.Io wrote:
Here is what I'm seeing.  
A minute after "Logged into master successfully" it says "Login to the master has failed, retrying connection".
Screen shot attached.



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 16:23 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Changing the password is not going to do you any good. The password for US Masters is "passw0rd" It's either logging in or not. Are you really sure it's ever logging in? This is what a successful login looks like:

M: 2019-08-01 23:20:21.455 MMDVM_Bridge-20180423 is running
D: 2019-08-01 23:20:31.493 DMR, Sending authorisation
D: 2019-08-01 23:20:31.540 DMR, Sending configuration
M: 2019-08-01 23:20:31.586 DMR, Logged into the master successfully
 

On 8/1/19 6:40 PM, Chris K7AZ via Groups.Io wrote:
When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric



Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Adrian Fewster <vk4tux@...>
 

Have you tried port 62030 instead of 62031 ?

On 2/8/19 1:12 pm, Chris K7AZ via Groups.Io wrote:
The same problem persists across 4 different Masters.  

I don't have this email on the laptop being used to TV into the VM server across town.  

I'll hand transcribe as needed to avoid sending pictures.  



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 19:06 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Chris,
You have a problem with your connection to the Master, simple as that. Have you tried another Master? PLEASE learn to capture the test and paste it into a e-mail. No more cell phone pictures.

On 8/1/19 10:00 PM, Chris K7AZ via Groups.Io wrote:
Here is what I'm seeing.  
A minute after "Logged into master successfully" it says "Login to the master has failed, retrying connection".
Screen shot attached.



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 16:23 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Changing the password is not going to do you any good. The password for US Masters is "passw0rd" It's either logging in or not. Are you really sure it's ever logging in? This is what a successful login looks like:

M: 2019-08-01 23:20:21.455 MMDVM_Bridge-20180423 is running
D: 2019-08-01 23:20:31.493 DMR, Sending authorisation
D: 2019-08-01 23:20:31.540 DMR, Sending configuration
M: 2019-08-01 23:20:31.586 DMR, Logged into the master successfully
 

On 8/1/19 6:40 PM, Chris K7AZ via Groups.Io wrote:
When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric



Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Chris K7AZ
 

The same problem persists across 4 different Masters.  

I don't have this email on the laptop being used to TV into the VM server across town.  

I'll hand transcribe as needed to avoid sending pictures.  



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 19:06 (GMT-08:00)
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Chris,
You have a problem with your connection to the Master, simple as that. Have you tried another Master? PLEASE learn to capture the test and paste it into a e-mail. No more cell phone pictures.

On 8/1/19 10:00 PM, Chris K7AZ via Groups.Io wrote:
Here is what I'm seeing.  
A minute after "Logged into master successfully" it says "Login to the master has failed, retrying connection".
Screen shot attached.



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 16:23 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Changing the password is not going to do you any good. The password for US Masters is "passw0rd" It's either logging in or not. Are you really sure it's ever logging in? This is what a successful login looks like:

M: 2019-08-01 23:20:21.455 MMDVM_Bridge-20180423 is running
D: 2019-08-01 23:20:31.493 DMR, Sending authorisation
D: 2019-08-01 23:20:31.540 DMR, Sending configuration
M: 2019-08-01 23:20:31.586 DMR, Logged into the master successfully
 

On 8/1/19 6:40 PM, Chris K7AZ via Groups.Io wrote:
When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric



Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Steve N4IRS
 

Chris,
You have a problem with your connection to the Master, simple as that. Have you tried another Master? PLEASE learn to capture the test and paste it into a e-mail. No more cell phone pictures.

On 8/1/19 10:00 PM, Chris K7AZ via Groups.Io wrote:
Here is what I'm seeing.  
A minute after "Logged into master successfully" it says "Login to the master has failed, retrying connection".
Screen shot attached.



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 16:23 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Changing the password is not going to do you any good. The password for US Masters is "passw0rd" It's either logging in or not. Are you really sure it's ever logging in? This is what a successful login looks like:

M: 2019-08-01 23:20:21.455 MMDVM_Bridge-20180423 is running
D: 2019-08-01 23:20:31.493 DMR, Sending authorisation
D: 2019-08-01 23:20:31.540 DMR, Sending configuration
M: 2019-08-01 23:20:31.586 DMR, Logged into the master successfully
 

On 8/1/19 6:40 PM, Chris K7AZ via Groups.Io wrote:
When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric



Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Chris K7AZ
 

Here is what I'm seeing.  
A minute after "Logged into master successfully" it says "Login to the master has failed, retrying connection".
Screen shot attached.



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Steve N4IRS <szingman@...>
Date: 8/1/19 16:23 (GMT-08:00)
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

Changing the password is not going to do you any good. The password for US Masters is "passw0rd" It's either logging in or not. Are you really sure it's ever logging in? This is what a successful login looks like:

M: 2019-08-01 23:20:21.455 MMDVM_Bridge-20180423 is running
D: 2019-08-01 23:20:31.493 DMR, Sending authorisation
D: 2019-08-01 23:20:31.540 DMR, Sending configuration
M: 2019-08-01 23:20:31.586 DMR, Logged into the master successfully
 

On 8/1/19 6:40 PM, Chris K7AZ via Groups.Io wrote:
When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric


Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Steve N4IRS
 

Changing the password is not going to do you any good. The password for US Masters is "passw0rd" It's either logging in or not. Are you really sure it's ever logging in? This is what a successful login looks like:

M: 2019-08-01 23:20:21.455 MMDVM_Bridge-20180423 is running
D: 2019-08-01 23:20:31.493 DMR, Sending authorisation
D: 2019-08-01 23:20:31.540 DMR, Sending configuration
M: 2019-08-01 23:20:31.586 DMR, Logged into the master successfully
 

On 8/1/19 6:40 PM, Chris K7AZ via Groups.Io wrote:
When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric


Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Chris K7AZ
 

When I examine the master info for my repeater,  it shows Zeros all the way across the board. Is that good or bad?  

In MMDVM_Bridge.ini  it is again showing connecting and disconnecting every 2 minutes.  
Tweaking the master password again is not fixing that issue.  

Any hints very much appreciated.   :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:53 (GMT-08:00)
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

most of the time the file is there but it doesn't hurt to double check.

73, Eric


Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Eric-K6KWB
 

most of the time the file is there but it doesn't hurt to double check.

73, Eric


Re: NOOB Setup-Configuration Help #analog_bridge #dmrlink

Chris K7AZ
 

Thanks,  I'll plug in those and see what goes right  :)



Sent from my Verizon, Samsung Galaxy smartphone

-------- Original message --------
From: Eric Dayrit <kf6itc@...>
Date: 8/1/19 10:22 (GMT-08:00)
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] NOOB Setup-Configuration Help #dmrlink #analog_bridge

This works for me.

; Metadata management
subscriberFile = /var/lib/dvswitch/DMRIds.csv    ; DMR ID to callsign lookup data
exportMetadata = true                                         ; Export metadata to USRP partner (transcode setups require this)
 

4521 - 4540 of 9151