Date   

Re: Dvswitch server

Henrik Hansen
 

apt Install asterisk :) 

Phil <Zl2ro@...> schrieb am Fr., 10. Apr. 2020, 11:40:

Hi all i'm very new to this I have installed dvswitch on a Virtual box running Debian 10
Now for so reason I,m trying to  setup the ASL to DMR bridge however when go to  /etc/root@debian:/etc# cd /etc/asterisk
bash: cd: /etc/asterisk: No such file or directory  

can someone please help :)


Dvswitch server

Phil
 

Hi all i'm very new to this I have installed dvswitch on a Virtual box running Debian 10
Now for so reason I,m trying to  setup the ASL to DMR bridge however when go to  /etc/root@debian:/etc# cd /etc/asterisk
bash: cd: /etc/asterisk: No such file or directory  

can someone please help :)


Re: Talkgroup Announcement

Steve N4IRS
 

The updated version of P25Gateway is in Github. Make sure you get the Audio subdirectory also. You can not change the voice messages in this one either. The difference is in the new version the announcement is the TG numbers only. No more "North America" The old version had the words built into the code and could be changed IF you had the tools. The first release Jonathan did had another phrase for disconnected, Mike and I submitted the change that produced "disconnected"

Steve N4IRS


On 4/9/20 5:54 PM, Lily W. wrote:
Tagging off of this... Steve mentioned a while back that an updated version of P25_Gateway was in the works. Was that ever released? I'm still running the old version that doesn't allow voice announcements to be changed. 


-------- Original message --------
From: Scott Evans <vk7hse@...>
Date: 4/9/20 4:42 PM (GMT-06:00)
Subject: Re: [DVSwitch] Talkgroup Announcement

You must be using an old version of P25 clients because the current version uses number sequence to announce the talkgroup. The system that originally used the location announcement was P25NX. The reason for the change to the number sequence was to allow for the P25 reflectors that weren't covered by the previous type.


Re: Talkgroup Announcement

Lillian W.
 

Tagging off of this... Steve mentioned a while back that an updated version of P25_Gateway was in the works. Was that ever released? I'm still running the old version that doesn't allow voice announcements to be changed. 


-------- Original message --------
From: Scott Evans <vk7hse@...>
Date: 4/9/20 4:42 PM (GMT-06:00)
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] Talkgroup Announcement

You must be using an old version of P25 clients because the current version uses number sequence to announce the talkgroup. The system that originally used the location announcement was P25NX. The reason for the change to the number sequence was to allow for the P25 reflectors that weren't covered by the previous type.


Re: Talkgroup Announcement

Scott Evans
 

You must be using an old version of P25 clients because the current version uses number sequence to announce the talkgroup. The system that originally used the location announcement was P25NX. The reason for the change to the number sequence was to allow for the P25 reflectors that weren't covered by the previous type.


Re: Port errors ASL to DMR

Steve N4IRS
 

yes

On 4/9/2020 2:50 PM, Sean Burton wrote:
So, I assume if I run systemctl stop MMDVM_Bridge first then run the checks I should see what else is connected to the port?


--
Sent from my Android phone with mail.com Mail.


Re: Port errors ASL to DMR

Sean Burton
 

So, I assume if I run systemctl stop MMDVM_Bridge first then run the checks I should see what else is connected to the port?


--
Sent from my Android phone with mail.com Mail.


Re: Port errors ASL to DMR

Steve N4IRS
 

That means MMDVM_Bridge is already running.

On 4/9/2020 2:40 PM, Sean Burton wrote:
I have done those tests and it says that mmdvm_bridge is connected.

--
Sent from my Android phone with mail.com Mail.


Re: Port errors ASL to DMR

Sean Burton
 

I have done those tests and it says that mmdvm_bridge is connected.

--
Sent from my Android phone with mail.com Mail.


Re: Port errors ASL to DMR

Steve N4IRS
 

Sean,
This happens when another program is listening to 31103. Here are the commands you want to run to find out what is listening on 31103:
As root (sudo -s)
netstat -unap | grep 31103
ps ax | grep MMDVM_Bridge

Run the 2 commands above BEFORE you try to start MMDVM_Bridge and report the results.

73, Steve N4IRS

On 4/9/2020 2:23 PM, Sean Burton wrote:
I have set up an ASL to DMR bridge but I can't get it to work due to an error where it tells me it cannot connect to port 31103. I've run the checks and I can't find anything else connected to that port. Any ideas, bearing in mind my limited capabilities with coding. TIA


--
Sent from my Android phone with mail.com Mail.


Port errors ASL to DMR

Sean Burton
 

I have set up an ASL to DMR bridge but I can't get it to work due to an error where it tells me it cannot connect to port 31103. I've run the checks and I can't find anything else connected to that port. Any ideas, bearing in mind my limited capabilities with coding. TIA


--
Sent from my Android phone with mail.com Mail.


Re: Talkgroup Announcement

Pete Fierro <overthetop52@...>
 

I ran audacity to make my announcements on my analog repeater& the audio codec is ULAW..Never did it for digital

Pete
KD2ARB


On Thu, Apr 9, 2020 at 11:51, Jeff Carrier
<k0jsc.jeff@...> wrote:
Yes, I have one standalone non published reflector that only runs the reflector software. 

We also have a reflector with the gateway software so that one should be easy as soon as I figure out how to configure the announcement.


Re: Talkgroup Announcement

Jeff Carrier
 

Yes, I have one standalone non published reflector that only runs the reflector software. 

We also have a reflector with the gateway software so that one should be easy as soon as I figure out how to configure the announcement.


Re: Talkgroup Announcement

Steve N4IRS
 

I'm not sure I understand the question. P25Gateway announces to the user every time it connects or disconnects from a reflector. Do you mean my standalone, a non published reflector?

Steve N4IRS

On 4/9/2020 10:52 AM, Jeff Carrier wrote:
Thanks Steve, 

So even with a standalone P25Reflector I'd need to run P25Gateway to get an announcement I'm assuming?


Re: Talkgroup Announcement

Jeff Carrier
 

Thanks Steve, 

So even with a standalone P25Reflector I'd need to run P25Gateway to get an announcement I'm assuming?


Re: Talkgroup Announcement

Steve N4IRS
 

It is generated by the P25Gateway.

On 4/9/2020 9:41 AM, Jeff Carrier wrote:
Does anyone know where the talkgroup announcement (i.e. "North America" or "World Wide") comes from?  Is that generated by Pi-star or by P25Reflector?  I've searched the board and didn't find any info.  Perhaps I didn't use the right search query(s)


Re: Talkgroup Announcement

Kyle Robinson <K4KTR@...>
 

P25 reflector

Sent from Outlook Mobile




On Thu, Apr 9, 2020 at 9:41 AM -0400, "Jeff Carrier" <k0jsc.jeff@...> wrote:

Does anyone know where the talkgroup announcement (i.e. "North America" or "World Wide") comes from?  Is that generated by Pi-star or by P25Reflector?  I've searched the board and didn't find any info.  Perhaps I didn't use the right search query(s)


Talkgroup Announcement

Jeff Carrier
 

Does anyone know where the talkgroup announcement (i.e. "North America" or "World Wide") comes from?  Is that generated by Pi-star or by P25Reflector?  I've searched the board and didn't find any info.  Perhaps I didn't use the right search query(s)


Re: MMDVM to ASL bridge #mmdvm_bridge

john.brazel225@...
 

JJ,

Thanks for that. I’ll be back at the office in the morning and will give that a try. 


Re: MMDVM to ASL bridge #mmdvm_bridge

JJ Cummings
 

John..

You need to change the gain type (if you havn't) from the default to AUDIO_USE_GAIN.. then the changes will work, make big changes at first and smaller as you get closer to an acceptable level.  You'll need to restart the Analog_Bridge process every time that you make a change to test.

aslAudio = AUDIO_USE_GAIN        ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN)
agcGain = 1.65                   ; Gain (in db) of the AGC filter
dmrAudio = AUDIO_USE_GAIN         ; Audio from ASL (AUDIO_UNITY, AUDIO_GAIN, AUDIO_BPF)
dmrGain = 0.31                  ; Gain factor of audio from ASL (0.0-1.0)


On Wed, Apr 8, 2020 at 9:06 PM <john.brazel225@...> wrote:
Steve,

Thays where I run into the issue of it not changing. I can alter those settings and the end result is still the same. The DMR side being way overdriven when there is traffic coming from asl. I have tried multiple time, with numerous settings, and even tried reboots after making changes. Still poor audio quality on the DMR side. 

3841 - 3860 of 9925