Date   

Need another set of eyes #mmdvm_bridge

wojtek (voyteck)
 

I had a perfectly working bridge between YSF and BM TG. Suddenly it just quit working. Since it is built on Raspberry I figured after a brief investigation that the SD card is about to die. I got new cards and reinstall the whole system. I am running YSF Reflector and Bridge from one Pi. 
 I can see the bridge connecting to the reflector and to BM networks but it is not bridging the networks! I can see on dashboard traffic coming from YSF but not from DMR....everything looks good to my eyes.. HELP :-)
 
Here is a fresh log from the Bridge.
 

I: 2020-04-16 00:02:01.662 MMDVM_Bridge-20191105_V1.4.1 exited on receipt of SIGTERM
I: 2020-04-16 00:02:23.559 MMDVM_Bridge:
I: 2020-04-16 00:02:23.559 Portions Copyright (C) 2018 DVSwitch, INAD.
I: 2020-04-16 00:02:23.559 Hacks by Mike N4IRR and Steve N4IRS
I: 2020-04-16 00:02:23.559 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
I: 2020-04-16 00:02:23.559 This software is for use on amateur radio networks only,
I: 2020-04-16 00:02:23.560 it is to be used for educational purposes only. Its use on
I: 2020-04-16 00:02:23.560 commercial networks is strictly prohibited.
I: 2020-04-16 00:02:23.560 Copyright(C) 2015-2018 by Jonathan Naylor, G4KLX and others
M: 2020-04-16 00:02:23.560 MMDVM_Bridge-20191105_V1.4.1 is starting
M: 2020-04-16 00:02:23.560 Built 19:10:05 Nov 11 2019 (GitID #9dae1ac)
I: 2020-04-16 00:02:23.560 General Parameters
I: 2020-04-16 00:02:23.560     Callsign: NA9PL
I: 2020-04-16 00:02:23.560     Id: 3163052
I: 2020-04-16 00:02:23.560     Duplex: no
I: 2020-04-16 00:02:23.560     Timeout: 180s
I: 2020-04-16 00:02:23.560     D-Star: disabled
I: 2020-04-16 00:02:23.560     DMR: enabled
I: 2020-04-16 00:02:23.560     YSF: enabled
I: 2020-04-16 00:02:23.560     P25: disabled
I: 2020-04-16 00:02:23.560     NXDN: disabled
I: 2020-04-16 00:02:23.560 Modem Parameters
I: 2020-04-16 00:02:23.560     Port: /dev/null
I: 2020-04-16 00:02:23.560     RX Invert: no
I: 2020-04-16 00:02:23.560     TX Invert: no
I: 2020-04-16 00:02:23.560     PTT Invert: no
I: 2020-04-16 00:02:23.560     TX Delay: 100ms
I: 2020-04-16 00:02:23.560     RX Offset: 0Hz
I: 2020-04-16 00:02:23.560     TX Offset: 0Hz
I: 2020-04-16 00:02:23.560     RX DC Offset: 0
I: 2020-04-16 00:02:23.560     TX DC Offset: 0
I: 2020-04-16 00:02:23.560     RF Level: 100.0%
I: 2020-04-16 00:02:23.560     DMR Delay: 0 (0.0ms)
I: 2020-04-16 00:02:23.560     RX Level: 50.0%
I: 2020-04-16 00:02:23.560     CW Id TX Level: 50.0%
I: 2020-04-16 00:02:23.560     D-Star TX Level: 50.0%
I: 2020-04-16 00:02:23.560     DMR TX Level: 50.0%
I: 2020-04-16 00:02:23.560     YSF TX Level: 50.0%
I: 2020-04-16 00:02:23.560     P25 TX Level: 50.0%
I: 2020-04-16 00:02:23.560     NXDN TX Level: 50.0%
I: 2020-04-16 00:02:23.560     RX Frequency: 222340000Hz (222340000Hz)
I: 2020-04-16 00:02:23.560     TX Frequency: 224940000Hz (224940000Hz)
M: 2020-04-16 00:02:23.560 Opening the MMDVM
I: 2020-04-16 00:02:23.560 Display Parameters
I: 2020-04-16 00:02:23.560     Type:
I: 2020-04-16 00:02:23.579 DMR Network Parameters
I: 2020-04-16 00:02:23.579     Address: bm2602.ham-dmr.pl
I: 2020-04-16 00:02:23.579     Port: 62031
I: 2020-04-16 00:02:23.579     Local: random
I: 2020-04-16 00:02:23.579     Jitter: 360ms
I: 2020-04-16 00:02:23.579     Slot 1: disabled
I: 2020-04-16 00:02:23.579     Slot 2: enabled
I: 2020-04-16 00:02:23.579     Mode Hang: 3s
I: 2020-04-16 00:02:23.787 Info Parameters
I: 2020-04-16 00:02:23.787     Callsign: NA9PL
I: 2020-04-16 00:02:23.787     RX Frequency: 222340000Hz
I: 2020-04-16 00:02:23.787     TX Frequency: 224940000Hz
I: 2020-04-16 00:02:23.787     Power: 1W
I: 2020-04-16 00:02:23.787     Latitude: 42.094589deg N
I: 2020-04-16 00:02:23.787     Longitude: -87.971237deg E
I: 2020-04-16 00:02:23.787     Height: 700m
I: 2020-04-16 00:02:23.787     Location: "Arlington Heights, IL, USA"
I: 2020-04-16 00:02:23.787     Description: "NA9PL_PAAROS_MMDVM_Bridge"
I: 2020-04-16 00:02:23.787     URL: "http://PAAROS.com"
M: 2020-04-16 00:02:23.787 DMR, Opening DMR Network
I: 2020-04-16 00:02:23.787 System Fusion Network Parameters
I: 2020-04-16 00:02:23.787     Local Address: 0
I: 2020-04-16 00:02:23.787     Local Port: 3200
I: 2020-04-16 00:02:23.788     Gateway Address: 64.53.214.179
I: 2020-04-16 00:02:23.788     Gateway Port: 42005
I: 2020-04-16 00:02:23.788     Mode Hang: 3s
M: 2020-04-16 00:02:23.788 Opening YSF network connection
I: 2020-04-16 00:02:23.788 RSSI
I: 2020-04-16 00:02:23.788     Mapping File: RSSI.dat
W: 2020-04-16 00:02:23.788 Cannot open the RSSI data file - RSSI.dat
I: 2020-04-16 00:02:23.788 DMR Id Lookups
I: 2020-04-16 00:02:23.788     File: /var/lib/mmdvm/DMRIds.dat
I: 2020-04-16 00:02:23.788     Reload: 24 hours
I: 2020-04-16 00:02:23.789 DMR RF Parameters
I: 2020-04-16 00:02:23.789 Started the DMR Id lookup reload thread
I: 2020-04-16 00:02:23.789     Id: 3163052
I: 2020-04-16 00:02:23.789     Color Code: 1
I: 2020-04-16 00:02:23.789     Self Only: no
I: 2020-04-16 00:02:23.789     Embedded LC Only: yes
I: 2020-04-16 00:02:23.789     Dump Talker Alias Data: no
I: 2020-04-16 00:02:23.789     Prefixes: 0
I: 2020-04-16 00:02:23.789     Call Hang: 3s
I: 2020-04-16 00:02:23.789     TX Hang: 3s
I: 2020-04-16 00:02:23.789     Mode Hang: 10s
M: 2020-04-16 00:02:23.789 DMR, Opening INI file: DVSwitch.ini
M: 2020-04-16 00:02:23.791 DMR, Setting [DMR] Address -> 127.0.0.1
M: 2020-04-16 00:02:23.791 DMR, Setting [DMR] TXPort -> 32001
M: 2020-04-16 00:02:23.791 DMR, Setting [DMR] RXPort -> 32005
M: 2020-04-16 00:02:23.792 DMR, Setting [DMR] Slot -> 2
M: 2020-04-16 00:02:23.792 DMR, Transmitting on 127.0.0.1:32001 and listening on port 32005.  Result = 1
I: 2020-04-16 00:02:23.792 YSF RF Parameters
I: 2020-04-16 00:02:23.792     Low Deviation: no
I: 2020-04-16 00:02:23.792     Remote Gateway: no
I: 2020-04-16 00:02:23.792     Self Only: no
I: 2020-04-16 00:02:23.792     DSQ: no
I: 2020-04-16 00:02:23.792     Mode Hang: 10s
M: 2020-04-16 00:02:23.792 YSF, Opening INI file: DVSwitch.ini
M: 2020-04-16 00:02:23.792 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-04-16 00:02:23.792 YSF, Setting [YSF] TXPort -> 32005
M: 2020-04-16 00:02:23.792 YSF, Setting [YSF] RXPort -> 32001
M: 2020-04-16 00:02:23.792 YSF, Setting [YSF] FallbackID -> 1234567
M: 2020-04-16 00:02:23.792 YSF, Setting [YSF] ExportTG -> 26018
M: 2020-04-16 00:02:23.792 YSF, Setting [YSF] Slot -> 2
M: 2020-04-16 00:02:23.793 YSF, Transmitting on 127.0.0.1:32005 and listening on port 32001.  Result = 1
M: 2020-04-16 00:02:23.793 MMDVM_Bridge-20191105_V1.4.1 is running
M: 2020-04-16 00:02:34.237 DMR, Logged into the master successfully
 
 


Can you have several instances of Dvswicth running in different folders with the dvswitch.sh?

EA5GVK Joaquin
 

I want to have several DVSwitch users running on the same raspberry pi.
I have different folders for the main user, with their mmdvm_bridge, analog_bridge and md380-emu.
And in a different folder I have a secondary user, with the same folders mmdvm_bridge, analog_bridge and md380-emu.
Of course I have changed ports in DVSwitch.ini from the MMDVM_Bridge folder.
But do you have to change anything in the dvswitch.sh script of the second user?
Many thx.


Re: Setup of a Bridge YSF to DMR - Anyone out there who can solve this mystery ? #mmdvm_bridge

Alec Wasserman
 

Yes double check ysf gateway port.  Everything has to match and it will work !


Re: Setup of a Bridge YSF to DMR - Anyone out there who can solve this mystery ? #mmdvm_bridge

Steve N4IRS
 

Uli,
Do not worry about the Dashboard. You want to look at the MMDVM_Bridge log file. If you setup MMDVM_Bridge.ini and DVSwitch.ini as the wiki states, all you should have to do is point MMDVM_Bridge at the 2 systems you want to bridge see below:

[DMR Network]
Enable=1
Address=hblink.dvswitch.org <---------- Point this at the DMR network
Port=62031
Jitter=360
Local=62032
Password=passw0rd
Slot1=0
Slot2=1
Debug=0

[System Fusion Network]
Enable=1
LocalAddress=0
LocalPort=3200
GatewayAddress=ysfreflector.dvswitch.org <-------- point this at the YSF reflector
GatewayPort=42166 <-------- Set this to the proper port for the reflector
Debug=0


Steve, N4IRS


On 4/15/2020 4:17 AM, Uli wrote:
I simply want to link my YSF Reflector to a Talkgroup on Brandmeister.

Meanwhile I have tried 4 full installation attempts to do a Bridge between YSF and DMR but no luck.
I have 2 RPI 3B+, both running raspbian stretch lite. One has a YSF Reflector installed according to QSO365´s (very good and working ) explanation. This Reflector and its Dashboard installed on the first attempt and runs fine without problems
The other RPI 3B+ also has raspbian stretch lite installed, PHP7.0 and on top of it DVSwitch-System-Builder.

Both RPi´s are running in the same Network 192.168.10.xxx behind a firewall.
I was able to get the MMDVM_Bridge Dashboard running but it does not show any links or connection attempts from HT´s and the status is always idle.
How do I get the MMDVM Bridge to link my reflector to the Brandmeister TG i have entered in DVSwitch.ini?

Is there a complete detailed description which values in MMDVM_Bridge.ini and DVSwitch.ini and possibly in any other hidden config files or somewhere else need to be changed/adapted and how?
I have done the suggested changes of values in the config files  like from this https://dvswitch.groups.io/g/main/wiki/Bridge-DMR-to-YSF-Narrow
but there are a lot of unanswered questions e.g. what do I put in "DMR adress" (I assume its the Brandmeister  Master??) or in YSF Gateway Address (is it the URL of the other Pi that runs the Reflector?)
What other ports do I need to open up on the firewall ?
How should the config files look like for my setup?
I have tried everything I could think of but no luck, the Bridge does not work as it should

Do I need anything else (Software or Hardware than the two Raspberrys to do this? Did I miss anything?
I´m completely stuck at this point.

any help would greatly be appreciated

Uli
DJ5UW



Setup of a Bridge YSF to DMR - Anyone out there who can solve this mystery ? #mmdvm_bridge

Uli
 

I simply want to link my YSF Reflector to a Talkgroup on Brandmeister.

Meanwhile I have tried 4 full installation attempts to do a Bridge between YSF and DMR but no luck.
I have 2 RPI 3B+, both running raspbian stretch lite. One has a YSF Reflector installed according to QSO365´s (very good and working ) explanation. This Reflector and its Dashboard installed on the first attempt and runs fine without problems
The other RPI 3B+ also has raspbian stretch lite installed, PHP7.0 and on top of it DVSwitch-System-Builder.

Both RPi´s are running in the same Network 192.168.10.xxx behind a firewall.
I was able to get the MMDVM_Bridge Dashboard running but it does not show any links or connection attempts from HT´s and the status is always idle.
How do I get the MMDVM Bridge to link my reflector to the Brandmeister TG i have entered in DVSwitch.ini?

Is there a complete detailed description which values in MMDVM_Bridge.ini and DVSwitch.ini and possibly in any other hidden config files or somewhere else need to be changed/adapted and how?
I have done the suggested changes of values in the config files  like from this https://dvswitch.groups.io/g/main/wiki/Bridge-DMR-to-YSF-Narrow
but there are a lot of unanswered questions e.g. what do I put in "DMR adress" (I assume its the Brandmeister  Master??) or in YSF Gateway Address (is it the URL of the other Pi that runs the Reflector?)
What other ports do I need to open up on the firewall ?
How should the config files look like for my setup?
I have tried everything I could think of but no luck, the Bridge does not work as it should

Do I need anything else (Software or Hardware than the two Raspberrys to do this? Did I miss anything?
I´m completely stuck at this point.

any help would greatly be appreciated

Uli
DJ5UW


Re: Setting up DVSwitch Mobile with ASL

Steve N4IRS
 


From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of honda5603@... <honda5603@...>
Sent: Tuesday, April 14, 2020 11:07:03 AM
To: main@DVSwitch.groups.io <main@DVSwitch.groups.io>
Subject: [DVSwitch] Setting up DVSwitch Mobile with ASL
 
Are there instructions available for setting up the iax.conf file and extensions.conf file for accepting connections from my Android phone?


Setting up DVSwitch Mobile with ASL

honda5603@...
 

Are there instructions available for setting up the iax.conf file and extensions.conf file for accepting connections from my Android phone?


Motorola xpr5550 to brandmeister DMR over IP?

bastiansotopainemal@...
 

Hi, I have a question friends... it is possible to connect my XPR5550 to Brandmeister only through the IPSC connection (without another device, only with the wifi connection of the equipment...)
What would the setup be like, if someone were so kind to help me...
 
73 '
CD6BDS Bastian Soto, radio amateur from Chile.


Re: autogain

EA3BIL_Rafa
 
Edited

As far as I've been able to "see", YSF does always show low audio level when received on DMR.
I guess it has some kind of link to the need to use YSF on DN modulation when using multimode nodes.
Anyway, in the same line if thinking it does not make make sense when they use their YSF only nodes (so they can use DW and theorically improved audio response) and I have the same results on DMR side.

I agree about comments on low audio level.
It looks like a "brand mark" on YSF.

Anyway it's easy to fix:
Tell the colleague on YSF to SPEAK UP.
;)


Re: autogain

Patrick Perdue
 

Hi Mike:

Very cool. Thanks for looking at this.

I agree re digital modes. Also, Fusion radios tend to have some dithering built-in, or something. There always seems to be some constant low level white noise on those radios when in YSF mode, for some reason. I don't hear that on DMR or DSTAR. To be fair, I don't have any YSF equipment myself, and am hearing this through DMR, but theoretically, that shouldn't matter.


On 4/13/2020 5:07 PM, Mike Zingman - N4IRR wrote:
Partick,

Thanks for the message.  When I put the AGC code in, I was playing with several functions and never really did finish the work on this.  Today I looked back. at what was included and it is pretty rough.  So, I am playing with a new (for me) algorithm and it seems to perform much better than the included code.  Not sure how I will expose the tuning parameters (threshold, slope and decay), but I am continuing to test.  If I allow dynamic updates to the parameters I will have to protect the internal structures from being modified while audio is present.  

For me, the modes with the greatest range are DMR and DSTAR on the loud end and fusion on the quiet end.  Not that the AMBE is different, but the different radio manufactures tend to have vastly different front end gains defined by default.  Playing on several of the bridges where all of these modes tend to be present.

Mike N4IRR   


Re: autogain

Mike Zingman - N4IRR
 

Partick,

Thanks for the message.  When I put the AGC code in, I was playing with several functions and never really did finish the work on this.  Today I looked back. at what was included and it is pretty rough.  So, I am playing with a new (for me) algorithm and it seems to perform much better than the included code.  Not sure how I will expose the tuning parameters (threshold, slope and decay), but I am continuing to test.  If I allow dynamic updates to the parameters I will have to protect the internal structures from being modified while audio is present.  

For me, the modes with the greatest range are DMR and DSTAR on the loud end and fusion on the quiet end.  Not that the AMBE is different, but the different radio manufactures tend to have vastly different front end gains defined by default.  Playing on several of the bridges where all of these modes tend to be present.

Mike N4IRR   


autogain

Patrick Perdue
 

Hi all:

For the entire time I've been using DVSwitch, I've had usrpAudio=AUDIO_USE_Gain on Analog_Bridge. I'd like to use AGC, as dynamic range from DMR can be quite wide, but I find the attack and release to be way too fast, yielding a very crunchy effect, even with moderately hot DMR audio. Decreasing the gain just turns down the output. The input is still just as squished, just quieter. I like the idea, just want a smoother implementation of it. I think increasing the release time a little, and perhaps raising the threshold slightly would improve things, but I don't see a way to do this. Is this possible at all with the algorithm currently being used? If so, could this be added as a set of user adjustable parameter in Analog_Bridge?

Thanks and 73

de

KE4DYI


Re: allstar asterisk Help please

Ken KE2N
 

phil - you did not say how you got to where you are, but this looks like a typical missing dahdi module problem.

If it is a new install of the existing ASL image you may just need to compile dahdi from the directory where the source is.

If you have done an update to the OS and did not "pin headers" then you need to follow the readme that covers that topic.   


allstar asterisk Help please

Phil
 

Hi Having some issues with my setup see can anyone help.  Reading Master Configuration ]
[ Initializing Custom Configuration Options ]
[Apr 12 17:31:34] NOTICE[1172]: dnsmgr.c:394 do_reload: Managed DNS entries will be refreshed every 300 seconds.
[Apr 12 17:31:34] NOTICE[1172]: cdr.c:1416 do_reload: CDR simple logging enabled.
[Apr 12 17:31:34] NOTICE[1172]: loader.c:874 load_modules: 56 modules will be loaded.
..............[Apr 12 17:31:34] WARNING[1172]: chan_iax2.c:12750 load_module: Unable to open IAX timing interface: No such file or directory
.......................................... ]
Asterisk Ready.
*CLI> [Apr 12 17:31:35] NOTICE[1178]: app_rpt.c:22184 rpt_master: Normal Repeater Init  51178
[Apr 12 17:31:35] WARNING[1193]: chan_dahdi.c:928 dahdi_open: Unable to open '/dev/dahdi/pseudo': No such file or directory
[Apr 12 17:31:35] ERROR[1193]: chan_dahdi.c:7906 chandup: Unable to dup channel: No such file or directory
rpt:Sorry unable to obtain pseudo channel
[Apr 12 17:31:35] WARNING[1178]: app_rpt.c:22240 rpt_master: rpt_thread restarted on node 51178
[Apr 12 17:31:35] WARNING[1194]: chan_dahdi.c:928 dahdi_open: Unable to open '/dev/dahdi/pseudo': No such file or directory
[Apr 12 17:31:35] ERROR[1194]: chan_dahdi.c:7906 chandup: Unable to dup channel: No such file or directory
rpt:Sorry unable to obtain pseudo channel
[Apr 12 17:31:37] NOTICE[1178]: app_rpt.c:22228 rpt_master: RPT thread restarted on 51178
[Apr 12 17:31:37] WARNING[1178]: app_rpt.c:22240 rpt_master: rpt_thread restarted on node 51178
[Apr 12 17:31:37] WARNING[1195]: chan_dahdi.c:928 dahdi_open: Unable to open '/dev/dahdi/pseudo': No such file or directory
[Apr 12 17:31:37] ERROR[1195]: chan_dahdi.c:7906 chandup: Unable to dup channel: No such file or directory
rpt:Sorry unable to obtain pseudo channel
[Apr 12 17:31:39] NOTICE[1178]: app_rpt.c:22228 rpt_master: RPT thread restarted on 51178
[Apr 12 17:31:39] WARNING[1178]: app_rpt.c:22240 rpt_master: rpt_thread restarted on node 51178
[Apr 12 17:31:39] WARNING[1196]: chan_dahdi.c:928 dahdi_open: Unable to open '/dev/dahdi/pseudo': No such file or directory
[Apr 12 17:31:39] ERROR[1196]: chan_dahdi.c:7906 chandup: Unable to dup channel: No such file or directory
rpt:Sorry unable to obtain pseudo channel
[Apr 12 17:31:41] NOTICE[1178]: app_rpt.c:22228 rpt_master: RPT thread restarted on 51178
[Apr 12 17:31:41] WARNING[1178]: app_rpt.c:22240 rpt_master: rpt_thread restarted on node 51178
[Apr 12 17:31:41] WARNING[1197]: chan_dahdi.c:928 dahdi_open: Unable to open '/dev/dahdi/pseudo': No such file or directory
[Apr 12 17:31:41] ERROR[1197]: chan_dahdi.c:7906 chandup: Unable to dup channel: No such file or directory
rpt:Sorry unable to obtain pseudo channel
[Apr 12 17:31:43] NOTICE[1178]: app_rpt.c:22228 rpt_master: RPT thread restarted on 51178
[Apr 12 17:31:43] WARNING[1178]: app_rpt.c:22240 rpt_master: rpt_thread restarted on node 51178
[Apr 12 17:31:43] WARNING[1198]: chan_dahdi.c:928 dahdi_open: Unable to open '/dev/dahdi/pseudo': No such file or directory
[Apr 12 17:31:43] ERROR[1198]: chan_dahdi.c:7906 chandup: Unable to dup channel: No such file or directory
rpt:Sorry unable to obtain pseudo channel
[Apr 12 17:31:45] NOTICE[1178]: app_rpt.c:22228 rpt_master: RPT thread restarted on 51178
[Apr 12 17:31:45] WARNING[1178]: app_rpt.c:22240 rpt_master: rpt_thread restarted on node 51178
[Apr 12 17:31:45] WARNING[1202]: chan_dahdi.c:928 dahdi_open: Unable to open '/dev/dahdi/pseudo': No such file or directory
[Apr 12 17:31:45] ERROR[1202]: chan_dahdi.c:7906 chandup: Unable to dup channel: No such file or directory
rpt:Sorry unable to obtain pseudo channel
[Apr 12 17:31:47] ERROR[1178]: app_rpt.c:22223 rpt_master: Continual RPT thread restarts, killing Asterisk
root@DVNZ:/etc/asterisk#


Re: Talkgroup Announcement

Steve N4IRS
 

There is only one P25Gateway

On 4/10/20 8:18 PM, Kevin N9OIG wrote:
Is this updated for quantar bridge also?


Re: Talkgroup Announcement

Kevin N9OIG
 

Is this updated for quantar bridge also?


Re: Dvswitch server

Phil
 

Thank you :)


Re: Dvswitch server

Raul cruz <rcw3023@...>
 

Did you try typing  sudo fiist

Sent from my T-Mobile 4G LTE Device


From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of Henrik Hansen via groups.io <hhansen06@...>
Sent: Friday, April 10, 2020 5:41:39 AM
To: main@dvswitch.groups.io <main@dvswitch.groups.io>
Subject: Re: [DVSwitch] Dvswitch server
 
apt Install asterisk :) 

Phil <Zl2ro@...> schrieb am Fr., 10. Apr. 2020, 11:40:
Hi all i'm very new to this I have installed dvswitch on a Virtual box running Debian 10
Now for so reason I,m trying to  setup the ASL to DMR bridge however when go to  /etc/root@debian:/etc# cd /etc/asterisk
bash: cd: /etc/asterisk: No such file or directory  

can someone please help :)


Re: Dvswitch server

Henrik Hansen
 

apt Install asterisk :) 

Phil <Zl2ro@...> schrieb am Fr., 10. Apr. 2020, 11:40:

Hi all i'm very new to this I have installed dvswitch on a Virtual box running Debian 10
Now for so reason I,m trying to  setup the ASL to DMR bridge however when go to  /etc/root@debian:/etc# cd /etc/asterisk
bash: cd: /etc/asterisk: No such file or directory  

can someone please help :)


Dvswitch server

Phil
 

Hi all i'm very new to this I have installed dvswitch on a Virtual box running Debian 10
Now for so reason I,m trying to  setup the ASL to DMR bridge however when go to  /etc/root@debian:/etc# cd /etc/asterisk
bash: cd: /etc/asterisk: No such file or directory  

can someone please help :)

2981 - 3000 of 9083