Welcome to DVSwitch

Thanks Steve again for helping me.  Here's what I was able to capture:

Here's analog bridge ini:


; Analog_Bridge configuration file.
;   This file should be placed in either /etc or it can be
;   supplied as a path on the Analog_Bridge command line.

; The best way to think of this file is that there are two main sections, the USRP (analog audi$
; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined i$
; As you might expect, the reverse direction is defined too.

; Analog_Bridge supports include files. More on this later...
include = dvsm.macro
; include = asl.macro

; General Section describes settings for Analog_Bridge itself.
[GENERAL]
logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Mess$

; Metadata management
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data
exportMetadata = true                   ; Export metadata to USRP partner (transcode setups req$

; General vocoder setup information
decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is$
useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server

; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address = 127.0.0.1                     ; IP address of xx_Bridge
txPort = 35103                          ; Transmit TLV frames to partner on this port
rxPort = 35100                          ; Listen for TLV frames from partner on this port
ambeMode = YSFN                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode $
minTxTimeMS = 2500                      ; Minimum time in MS for hang delay (0-10000)

; The metadata below is used when ASL is the source since it does not have any concept of digit$
gatewayDmrId = 3118583                  ; ID to use when transmitting from Analog_Bridge
repeaterID = 311858301                  ; ID of source repeater
txTg = 37921                          ; TG to use for all frames sent from Analog_Bridge -> xx_$
txTs = 2                                ; Slot to use for frames sent from Analog_Bridge -> xx_$
colorCode = 1                           ; Color Code to assign DMR frames

; Information for USRP channel driver.  This interface uses PCM to transfer audio information
; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog cli$
; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces bac$
; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.
;   When using ASL, this matches the rpt.conf ASL file with a setting like:
;   rxchannel = usrp/127.0.0.1:34001:32001
;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (cro$
;   each instance with its own ini file.
[USRP]
address = 127.0.0.1                     ; IP address of USRP partner (Allstar/Asterisk or anoth$
txPort = 35103                          ; Transmit USRP frames on this port
rxPort = 33510                          ; Listen for USRP frames on this port
usrpAudio = AUDIO_UNITY                 ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_G$
usrpGain = 1.10                         ; Gain (in db) of the AGC filter
tlvAudio = AUDIO_UNITY                  ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BP$
tlvGain = 0.35                          ; Gain factor of audio from ASL (0.0-1.0)

Here is the DVSwitch.ini file:



  GNU nano 2.7.4                          File: DVSwitch.ini

; MMDVM_Bridge export / import configuration file.
;   This file should be placed along side of MMDVM_Bridge or it can be
;   supplied as a path on the MMDVM_BRIDGE environment variable.

; Configure the Quantar Repeater Partner
; Note that the TX and RX ports are already reversed for MMDVM_Bridge <--> Quantar_Bridge
[QUANTAR]
logFilePath = /var/log/Quantar_Bridge.log
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 34103                  ; Port to send AMBE TLV frames to (export)
RXPort = 34100                  ; Port to listen on (import)
quantarPort = 1994              ; HDLC frames To/From the Quantar repeater
logLevel = 2                    ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=I$
debug = 0                       ; Debug 0 = off, 1 = on (adds lots of additional messages)

; Configure the DMR Partner
; Audio format is AMBE 72 bit
[DMR]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 31100                  ; Port to send AMBE TLV frames to (export)
RXPort = 31103                  ; Port to listen on (import)
Slot = 2                        ; Export slot

; Configure the D-Star Partner
; Audio format is AMBE 48 bit (DSAMBE)
[DSTAR]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 32100                  ; Port to send AMBE TLV frames to (export)
RXPort = 32103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, expor$
ExportTG = 9                    ; Which TG to export
Slot = 2                        ; Export slot

; Configure the NXDN Partner
; Audio format is AMBE 72 bit
[NXDN]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 33100                  ; Port to send AMBE TLV frames to (export)
RXPort = 33103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, expor$
NXDNFallbackID  = 12345         ; Use this ID when the input DMR ID is not found in the database
Translate = 1234=4321           ; Translate NXDN TG < -- > DMR TG (bidirectional)
Slot = 2                        ; Export slot

; Configure the P25 Partner
; Audio format is IMBE 88 bit
[P25]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 34100                  ; Port to send AMBE TLV frames to (export)
RXPort = 34103                  ; Port to listen on (import)
Slot = 2                        ; Export slot

; Configure the Yaesu Fusion Partner
; Audio format is AMBE 72 bit
; Audio format is IMBE 88 bit
[YSF]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 35100                  ; Port to send AMBE TLV frames to (export)
RXPort = 35103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, expor$
ExportTG = 1234                 ; Which TG to export
Slot = 2                        ; Export slot


And then the MMDVM_Bridge.ini:


[General]
Callsign=KC9HTA
Id=311858301
Timeout=180
Duplex=0

[Info]
RXFrequency=222340000
TXFrequency=224940000
Power=1
Latitude=41.7333
Longitude=-50.3999
Height=0
Location=Iceberg, North Atlantic
Description=MMDVM_Bridge
URL=https://groups.io/g/DVSwitch

[Log]
# Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
DisplayLevel=1
FileLevel=2
FilePath=/var/log/mmdvm
FileRoot=MMDVM_Bridge

[DMR Id Lookup]
File=/var/lib/mmdvm/DMRIds.dat
Time=24

[NXDN Id Lookup]
File=/var/lib/mmdvm/NXDN.csv
Time=24

[Modem]
Port=/dev/null
RSSIMappingFile=RSSI.dat
Trace=0
Debug=0

[D-Star]
Enable=0
Module=C

[DMR]
Enable=0
ColorCode=1
EmbeddedLCOnly=1
DumpTAData=0

[System Fusion]
Enable=0

[P25]
Enable=0
NAC=293

[NXDN]
Enable=0
RAN=1
Id=12345

[D-Star Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=20010
LocalPort=20011
Debug=0

[DMR Network]
Enable=0
Address=3108.repeater.net
Port=62031
Jitter=360
Local=62032
Password=passw0rd
# for DMR+ see https://github.com/DVSwitch/MMDVM_Bridge/blob/master/DOC/DMRplus_startup_options$
# for XLX the syntax is: Options=XLX:4009
# Options=
Slot1=0
Slot2=1
Debug=0

[System Fusion Network]
Enable=1
LocalAddress=127.0.0.1
LocalPort=3200
GatewayAddress=ysfreflector.dvswitch.org
GatewayPort=42166
Debug=0

Thanks Steve for the information I just confirmed DMR, but need to swap everything to YSF?

What's the easiest way to bridge both of these together? 

And dvswitch for VPS  (amd64)   ?

 

 

De : main@DVSwitch.groups.io <main@DVSwitch.groups.io> De la part de Steve N4IRS
Envoyé : dimanche 18:27
À : main@DVSwitch.groups.io
Objet : Re: [DVSwitch] Possible Loop in QSO DMR and MMDVM_Bridge or Analog_Bridge malfunction.

 

I have uploaded AB binary for armhf and a new copy of dvswitch.sh
Please test and report.

Steve N4IRS