Date   

Re: DSTAR

k7wby@...
 
Edited

First, Congratulation on your soon to be born new family member..

D-Star is a different animal but not so different that the pieces won't fit if assembled properly. Fortunately DVSwitch Server is an excellent way to bring the pieces together.

To understand D-Star, I highly recommend that you visit ircddb.net to better understand what's going on before you dive in. After you've gone there, head over to D-Star Info
and browse through their info. D-Star Info has plenty of info. As is typical with Ham Radio sites, there are a ton of assumptions made which will send you into at least one if not more guessing games. One of the first things that will mess you up is your D-Star Registration. While it clearly states that you only have to register once to use the reflectors you will soon find that some reflectors require additional registration. For instance REF030 is available to all registered D-Star users but REF014 requires permission from that reflectors owner/operator. It's these little things that can mess you up when you're trying to get things going. To begin with, use a test Reflector and avoid the loss of hair. More importantly, use a test reflector to avoid interfering with live traffic while you're getting it all figured out. 


Pi digital interface for Analog Radio (client)

Jim Kusznir
 

Hello:

I had a recent idea that I was wondering if I'm just crazy, or if this is actually reasonable.

We all know that MMDVM software allows someone to use the internet to create a repeater based on analog radios.  There are also software/hardware packages that allow using a mic and speaker and the internet to connect into DMR as a client (hold conversations, etc).

What about a device/software configuration that wold connect into the 9600 baud data port of an analog radio and a speaker and mic and allow the user to participate in the DMR system as a client through radio (eg, FT-8900 radio, for example)?

I know the STM_DVM board would have the physical connections necessary to interface to the analog radio (it already does that!); I'm not sure if it can act as a client rather than a repeater on the RF port though.

If it can, then the software (Blue DV or one of the equivalents) would need to know how to interface with a radio, or make use of a middle layer (DVSwitch software?)

Finally, is the analog radio able to T/R switch fast enough to do the TDM tx...

Is this doable, or am I just thinking wishfully?

--Jim, K7LL


DSTAR

Aaron Groover
 

Good Morning everyone!

 

First off I hope everyone is doing well. I am currently patiently waiting for my daughter to be born at the hospital. So while I wait lol…… I was looking at setting up DSTAR on the bridge. I know is different and all sorts but wanted to know the correct process as far as where to put i.e REF030C and where I can find the gateway info. Ive had the DMR and also Fusion up for weeks and had QSO’s with no issues.




--

 

Thank You,

 

Aaron Groover

(610) 379 6148

K3ALG@...

 

The content of this email is confidential and intended for the recipient specified in message only. It is strictly forbidden to share any part of this message with any third party, without a written consent of the sender. If you received this message by mistake, please reply to this message and follow with its deletion, so that we can ensure such a mistake does not occur in the future.


**This message has been composed on a mobile application. Please excuse any grammatical errors**


Re: #mmdvm_bridge #mmdvm_bridge

k7wby@...
 
Edited

Ok, I have some idea of what you're trying to accomplish. Sorry if some of this is redundant but others may want to understand:

Here's my take:
Install DVSwitch from the repository to /opt/ which creates
/opt/Analog_Bridge
/opt/md380-emu
/opt/MMDVM_Bridge
create two new folders in /opt/ 
/opt/mb1
opt/mb2
copy the entire contents of MMDVM_Bridge to mb1 and mb2
delete /opt/MMDVM_Bridge
disable mmdvm_bridge.service
create two new services in /etc/systemd/system based on the original service /etc/systemd/system/multi-user.target.wants/mmdvm_bridge.service
change each of the new .service's so they point to the new locations (/opt/mb1 and /opt/mb2). For instance, the following would be the service definition for the first MB instance I called MB1


[Unit]
Description=MMDVM_Bridge MB1 Service
# Description=Place this file in /lib/systemd/system
# Description=N4IRS 04/20/2018
 
# The device name should point to the
# port the mmdvm is plugged into.
# For USB ports (Arduino Due)
# BindTo=dev-ttyACM0.device
#
# To make the network-online.target available
# systemctl enable systemd-networkd-wait-online.service
 
After=network-online.target syslog.target netcheck.service
Wants=network-online.target
 
[Service]
StandardOutput=null
WorkingDirectory=/opt/MMDVM_Bridge (Change to /opt/MB1)
Environment=DVSwitch=/opt/MB1/DVSwitch.ini (Change to /opt/MB1)
RestartSec=3
ExecStart=/opt/MB1/MMDVM_Bridge /opt/MB1/MMDVM_Bridge.ini (Change to /opt/MB1)
Restart=on-abort
 
[Install]
WantedBy=multi-user.target

Modifiy the second mb service to point to the /opt/mb2/

Now go to /opt/mb2/DVSwitch.ini and modify it to point to a different set of ports than /opt/mb1/DVSwitch.ini. /opt/mb1/DVSwitch.ini can remain as is. If you don't do this you will likely get a "Cannot open port" error when you start the mb2 service and mb2 will fail. 

Finally:
systemctl enable mb1
systemctl start mb1
systemctl status mb1

if it's running then:
systemctl enable mb2
systemctl start mb2
systemctl status mb2

If both of your services start successfully then the problem is no longer with MB and I would look at the ports that are defined in DVSwitch and MB. We can go there next if this doesn't solve your issue.

K7WBY/Steve


Re: DVSwitch Server release date

Steve N4IRS
 


DVSwitch Server release date

Steve N4IRS
 

DVSwitch Server will be available for download at 12:00 UTC today.


Re: #mmdvm_bridge #mmdvm_bridge

swinger72@...
 

 in another way i have a nxdn reflector.he is linked to my ysfreflector and when i use my openspot2 nxdn to ysf they work flawlesly and no crash from mb1 or mb2


Re: #mmdvm_bridge #mmdvm_bridge

swinger72@...
 
Edited

Maybe i can try to change the  in each mb path to start ex mmdvmbridge1 and 2


Re: #mmdvm_bridge #mmdvm_bridge

swinger72@...
 

I create  new .service for each mb .mb1 and mb2 differenf path .in and .ini2


Re: #mmdvm_bridge #mmdvm_bridge

swinger72@...
 

Yes . I stop everything disable them and built my .ini
I already try to change rebuilt purge reinstall  update bimary try many other port . With the same issue. 


Re: #mmdvm_bridge #mmdvm_bridge

k7wby@...
 

You have two instances of MB created in two separate folders. Did you disable the original mmdvm_bridge service and create the two new ones that are needed for the two separate bridges?


Re: #mmdvm_bridge #mmdvm_bridge

swinger72@...
 

i just tried again on the old server and its caused the same problem


Re: #mmdvm_bridge #mmdvm_bridge

swinger72@...
 

Yes but recently mooved the ysfreflector on datacenter. The reason why now we seen this is issue is because  about 2 weeks ago i just close my bridge with brandmeister and all of this users  now pass by the dmr2ysf to reach my network


Re: #mmdvm_bridge #mmdvm_bridge

Steve N4IRS
 

You do not need YSFGateway. Are you saying this has been working over a year with ysf2dmr clients?

On 10/30/20 4:21 PM, swinger72@... wrote:
i point each mbridge directly to the ysfreflector ip .mb2 is local in the same server .my question is it is possible that is because i do not pass by ysfgateway? I have been working this way for 1 year now


Re: #mmdvm_bridge #mmdvm_bridge

swinger72@...
 

i point each mbridge directly to the ysfreflector ip .mb2 is local in the same server .my question is it is possible that is because i do not pass by ysfgateway? I have been working this way for 1 year now


Re: #mmdvm_bridge #mmdvm_bridge

Steve N4IRS
 

OK

On 10/30/2020 2:11 PM, swinger72@... wrote:
No im running in the same server as my ysfreflector


Re: #mmdvm_bridge #mmdvm_bridge

swinger72@...
 

No im running in the same server as my ysfreflector


Re: #mmdvm_bridge #mmdvm_bridge

Steve N4IRS
 

Are you using YSFGateway with mbridge2? I see this:

[System Fusion Network]
Enable=1
LocalAddress=0
LocalPort=3200
GatewayAddress=127.0.0.1
GatewayPort=42000
Debug=1

On 10/30/2020 2:03 PM, swinger72@... wrote:
mbridge2.ini
[General]
Callsign=va2tb
Id=302252804
Timeout=180
Duplex=0

[Info]
RXFrequency=000000000
TXFrequency=000000000
Power=1
Latitude=41.7333
Longitude=-50.3999
Height=0
Location=
Description=MMDVM_Bridge
URL=https:

[Log]
# Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
DisplayLevel=1
FileLevel=2
FilePath=/var/log/MMDVM_Bridge2
FileRoot=MMDVM_Bridge

[DMR Id Lookup]
File=/opt/DMRIds.dat
Time=24

[NXDN Id Lookup]
File=/var/lib/mmdvm/NXDN.csv
Time=24

[Modem]
Port=/dev/null
RSSIMappingFile=/dev/null
Trace=0
Debug=0

[D-Star]
Enable=0
Module=B

[DMR]
Enable=0
ColorCode=1
EmbeddedLCOnly=1
DumpTAData=0

[System Fusion]
Enable=1

[P25]
Enable=0
NAC=293

[NXDN]
Enable=0
RAN=1
Id=12345

[D-Star Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=20010
LocalPort=20011
Debug=0

[DMR Network]
Enable=0
Address=hblink.dvswitch.org
Port=62031
Jitter=360
Local=62032
Password=passw0rd
# for DMR+ see https://github.com/DVSwitch/MMDVM_Bridge/blob/master/DOC/DMRplus_startup_options.md
# for XLX the syntax is: Options=XLX:4009
# Options=
Slot1=0
Slot2=1
Debug=0

[System Fusion Network]
Enable=1
LocalAddress=0
LocalPort=3200
GatewayAddress=127.0.0.1
GatewayPort=42000
Debug=1

[P25 Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=42020
LocalPort=32010
Debug=0

[NXDN Network]
Enable=0
#LocalAddress=127.0.0.1
Debug=0
LocalPort=14021
GatewayAddress=127.0.0.1
GatewayPort=14020

Dvswitch
; MMDVM_Bridge export / import configuration file.
;   This file should be placed along side of MMDVM_Bridge or you can supply
;   an absolute path in the DVSWITCH environment variable, e.g:
;   DVSWITCH=/etc/MMDVM_Bridge/DVSwitch.ini
;   before executing MMDVM_Bridge
;
; Another method to set the enviorment variable is to use the systemd unit file
; by adding:
; Environment=DVSWITCH=/etc/MMDVM_Bridge/DVSwitch.ini
; to /lib/systemd/system/mmdvm_bridge.service

; Configure the Quantar Repeater Partner
; Note that the TX and RX ports are already reversed for MMDVM_Bridge <--> Quantar_Bridge
[QUANTAR]
address = 0.0.0.0               ; Address to send IMBE TLV frames to (export)
txPort = 34103                  ; Port to send IMBE TLV frames to (export)
rxPort = 34100                  ; Port to listen for IMBE TLV frames on (import)
quantarPort = 1994              ; HDLC frames To/From the Quantar repeater
debug = 0                       ; Debug 0 = off, 1 = on (adds lots of additional messages)
logLevel = 2                    ; Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
logFilePath = /var/log/dvswitch/Quantar_Bridge.log

; Configure the DMR Partner
; Audio format is AMBE 72 bit
[DMR]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 31100                  ; Port to send AMBE TLV frames to (export)
rxPort = 31103                  ; Port to listen on (import)
slot = 2                        ; Export slot
exportTG = 0                    ; Which TG to export
hangTimerInFrames = 0        ; Use 50 for 3 seconds of hang time (3000 / 60)
talkerAlias = %callsign %location %description ; Get callsign location and description from MMDVM_Bridge.ini

; Configure the D-Star Partner
; Audio format is AMBE 48 bit (DSAMBE)
[DSTAR]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 32100                  ; Port to send AMBE TLV frames to (export)
rxPort = 32103                  ; Port to listen on (import)
fallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
exportTG = 9                    ; Which TG to export
slot = 2                        ; Export slot
RemotePort = 54321        ; Port to send Gateway commands to
message = %location %description ; Get location and description from MMDVM_Bridge.ini

; Configure the NXDN Partner
; Audio format is AMBE 72 bit
[NXDN]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 33100                  ; Port to send AMBE TLV frames to (export)
rxPort = 33103                  ; Port to listen on (import)
fallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
nxdnFallbackID  = 12345         ; Use this ID when the input DMR ID is not found in the database
translate = 1234=4321           ; Translate NXDN TG < -- > DMR TG (bidirectional)
slot = 2                        ; Export slot
RemotePort = 6075        ; Port to send Gateway commands to

; Configure the P25 Partner
; Audio format is IMBE 88 bit
[P25]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 34100                  ; Port to send AMBE TLV frames to (export)
rxPort = 34103                  ; Port to listen on (import)
slot = 2                        ; Export slot
RemotePort = 6074        ; Port to send Gateway commands to

; Configure the Yaesu Fusion Partner
; Audio format is AMBE 72 bit
; Audio format is IMBE 88 bit
[YSF]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 43500                  ; Port to send AMBE TLV frames to (export)
rxPort = 42500                  ; Port to listen on (import)
txWidePort = 43500        ; Port to send IMBE TLV frames to for YSFw (export)
fallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
exportTG = 1234                    ; Which TG to export
slot = 2                        ; Export slot
RemotePort = 6073        ; Port to send Gateway commands to


Re: #mmdvm_bridge #mmdvm_bridge

swinger72@...
 

mbridge2.ini
[General]
Callsign=va2tb
Id=302252804
Timeout=180
Duplex=0

[Info]
RXFrequency=000000000
TXFrequency=000000000
Power=1
Latitude=41.7333
Longitude=-50.3999
Height=0
Location=
Description=MMDVM_Bridge
URL=https:

[Log]
# Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
DisplayLevel=1
FileLevel=2
FilePath=/var/log/MMDVM_Bridge2
FileRoot=MMDVM_Bridge

[DMR Id Lookup]
File=/opt/DMRIds.dat
Time=24

[NXDN Id Lookup]
File=/var/lib/mmdvm/NXDN.csv
Time=24

[Modem]
Port=/dev/null
RSSIMappingFile=/dev/null
Trace=0
Debug=0

[D-Star]
Enable=0
Module=B

[DMR]
Enable=0
ColorCode=1
EmbeddedLCOnly=1
DumpTAData=0

[System Fusion]
Enable=1

[P25]
Enable=0
NAC=293

[NXDN]
Enable=0
RAN=1
Id=12345

[D-Star Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=20010
LocalPort=20011
Debug=0

[DMR Network]
Enable=0
Address=hblink.dvswitch.org
Port=62031
Jitter=360
Local=62032
Password=passw0rd
# for DMR+ see https://github.com/DVSwitch/MMDVM_Bridge/blob/master/DOC/DMRplus_startup_options.md
# for XLX the syntax is: Options=XLX:4009
# Options=
Slot1=0
Slot2=1
Debug=0

[System Fusion Network]
Enable=1
LocalAddress=0
LocalPort=3200
GatewayAddress=127.0.0.1
GatewayPort=42000
Debug=1

[P25 Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=42020
LocalPort=32010
Debug=0

[NXDN Network]
Enable=0
#LocalAddress=127.0.0.1
Debug=0
LocalPort=14021
GatewayAddress=127.0.0.1
GatewayPort=14020

Dvswitch
; MMDVM_Bridge export / import configuration file.
;   This file should be placed along side of MMDVM_Bridge or you can supply
;   an absolute path in the DVSWITCH environment variable, e.g:
;   DVSWITCH=/etc/MMDVM_Bridge/DVSwitch.ini
;   before executing MMDVM_Bridge
;
; Another method to set the enviorment variable is to use the systemd unit file
; by adding:
; Environment=DVSWITCH=/etc/MMDVM_Bridge/DVSwitch.ini
; to /lib/systemd/system/mmdvm_bridge.service

; Configure the Quantar Repeater Partner
; Note that the TX and RX ports are already reversed for MMDVM_Bridge <--> Quantar_Bridge
[QUANTAR]
address = 0.0.0.0               ; Address to send IMBE TLV frames to (export)
txPort = 34103                  ; Port to send IMBE TLV frames to (export)
rxPort = 34100                  ; Port to listen for IMBE TLV frames on (import)
quantarPort = 1994              ; HDLC frames To/From the Quantar repeater
debug = 0                       ; Debug 0 = off, 1 = on (adds lots of additional messages)
logLevel = 2                    ; Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
logFilePath = /var/log/dvswitch/Quantar_Bridge.log

; Configure the DMR Partner
; Audio format is AMBE 72 bit
[DMR]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 31100                  ; Port to send AMBE TLV frames to (export)
rxPort = 31103                  ; Port to listen on (import)
slot = 2                        ; Export slot
exportTG = 0                    ; Which TG to export
hangTimerInFrames = 0        ; Use 50 for 3 seconds of hang time (3000 / 60)
talkerAlias = %callsign %location %description ; Get callsign location and description from MMDVM_Bridge.ini

; Configure the D-Star Partner
; Audio format is AMBE 48 bit (DSAMBE)
[DSTAR]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 32100                  ; Port to send AMBE TLV frames to (export)
rxPort = 32103                  ; Port to listen on (import)
fallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
exportTG = 9                    ; Which TG to export
slot = 2                        ; Export slot
RemotePort = 54321        ; Port to send Gateway commands to
message = %location %description ; Get location and description from MMDVM_Bridge.ini

; Configure the NXDN Partner
; Audio format is AMBE 72 bit
[NXDN]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 33100                  ; Port to send AMBE TLV frames to (export)
rxPort = 33103                  ; Port to listen on (import)
fallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
nxdnFallbackID  = 12345         ; Use this ID when the input DMR ID is not found in the database
translate = 1234=4321           ; Translate NXDN TG < -- > DMR TG (bidirectional)
slot = 2                        ; Export slot
RemotePort = 6075        ; Port to send Gateway commands to

; Configure the P25 Partner
; Audio format is IMBE 88 bit
[P25]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 34100                  ; Port to send AMBE TLV frames to (export)
rxPort = 34103                  ; Port to listen on (import)
slot = 2                        ; Export slot
RemotePort = 6074        ; Port to send Gateway commands to

; Configure the Yaesu Fusion Partner
; Audio format is AMBE 72 bit
; Audio format is IMBE 88 bit
[YSF]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 43500                  ; Port to send AMBE TLV frames to (export)
rxPort = 42500                  ; Port to listen on (import)
txWidePort = 43500        ; Port to send IMBE TLV frames to for YSFw (export)
fallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
exportTG = 1234                    ; Which TG to export
slot = 2                        ; Export slot
RemotePort = 6073        ; Port to send Gateway commands to


Re: #mmdvm_bridge #mmdvm_bridge

swinger72@...
 

mbridge 1.ini
[General]
Callsign=VA2TB
Id=302252802
Timeout=180
Duplex=0

[Info]
RXFrequency=000000000
TXFrequency=000000000
Power=1
Latitude=41.7333
Longitude=-50.3999
Height=0
Location=
Description=MMDVM_Bridge
URL=https:

[Log]
# Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
DisplayLevel=1
FileLevel=2
FilePath=/var/log/MMDVM_Bridge
FileRoot=MMDVM_Bridge

[DMR Id Lookup]
File=/opt/DMRIds.dat
Time=24

[NXDN Id Lookup]
File=/var/lib/mmdvm/NXDN.csv
Time=24

[Modem]
Port=/dev/null
RSSIMappingFile=/dev/null
Trace=0
Debug=0

[D-Star]
Enable=0
Module=B

[DMR]
Enable=0
ColorCode=1
EmbeddedLCOnly=1
DumpTAData=0

[System Fusion]
Enable=1

[P25]
Enable=0
NAC=293

[NXDN]
Enable=0
RAN=1
Id=12345

[D-Star Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=20010
LocalPort=20011
Debug=0

[DMR Network]
Enable=0
Address=hblink.dvswitch.org
Port=62031
Jitter=360
Local=62032
Password=passw0rd
# for DMR+ see https://github.com/DVSwitch/MMDVM_Bridge/blob/master/DOC/DMRplus_startup_options.md
# for XLX the syntax is: Options=XLX:4009
# Options=
Slot1=0
Slot2=1
Debug=0

[System Fusion Network]
Enable=1
LocalAddress=0
LocalPort=42200
GatewayAddress=151.80.143.185
GatewayPort=42002
Debug=1

[P25 Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=42020
LocalPort=32010
Debug=0

[NXDN Network]
Enable=0
#LocalAddress=127.0.0.1
Debug=0
LocalPort=14021
GatewayAddress=127.0.0.1
GatewayPort=14020

dvswitch
; MMDVM_Bridge export / import configuration file.
;   This file should be placed along side of MMDVM_Bridge or you can supply
;   an absolute path in the DVSWITCH environment variable, e.g:
;   DVSWITCH=/etc/MMDVM_Bridge/DVSwitch.ini
;   before executing MMDVM_Bridge
;
; Another method to set the enviorment variable is to use the systemd unit file
; by adding:
; Environment=DVSWITCH=/etc/MMDVM_Bridge/DVSwitch.ini
; to /lib/systemd/system/mmdvm_bridge.service

; Configure the Quantar Repeater Partner
; Note that the TX and RX ports are already reversed for MMDVM_Bridge <--> Quantar_Bridge
[QUANTAR]
address = 0.0.0.0               ; Address to send IMBE TLV frames to (export)
txPort = 34103                  ; Port to send IMBE TLV frames to (export)
rxPort = 34100                  ; Port to listen for IMBE TLV frames on (import)
quantarPort = 1994              ; HDLC frames To/From the Quantar repeater
debug = 0                       ; Debug 0 = off, 1 = on (adds lots of additional messages)
logLevel = 2                    ; Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
logFilePath = /var/log/dvswitch/Quantar_Bridge.log

; Configure the DMR Partner
; Audio format is AMBE 72 bit
[DMR]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 31100                  ; Port to send AMBE TLV frames to (export)
rxPort = 31103                  ; Port to listen on (import)
slot = 2                        ; Export slot
exportTG = 0                    ; Which TG to export
hangTimerInFrames = 0        ; Use 50 for 3 seconds of hang time (3000 / 60)
talkerAlias = %callsign %location %description ; Get callsign location and description from MMDVM_Bridge.ini

; Configure the D-Star Partner
; Audio format is AMBE 48 bit (DSAMBE)
[DSTAR]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 32100                  ; Port to send AMBE TLV frames to (export)
rxPort = 32103                  ; Port to listen on (import)
fallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
exportTG = 9                    ; Which TG to export
slot = 2                        ; Export slot
RemotePort = 54321        ; Port to send Gateway commands to
message = %location %description ; Get location and description from MMDVM_Bridge.ini

; Configure the NXDN Partner
; Audio format is AMBE 72 bit
[NXDN]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 33100                  ; Port to send AMBE TLV frames to (export)
rxPort = 33103                  ; Port to listen on (import)
fallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
nxdnFallbackID  = 12345         ; Use this ID when the input DMR ID is not found in the database
translate = 1234=4321           ; Translate NXDN TG < -- > DMR TG (bidirectional)
slot = 2                        ; Export slot
RemotePort = 6075        ; Port to send Gateway commands to

; Configure the P25 Partner
; Audio format is IMBE 88 bit
[P25]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 34100                  ; Port to send AMBE TLV frames to (export)
rxPort = 34103                  ; Port to listen on (import)
slot = 2                        ; Export slot
RemotePort = 6074        ; Port to send Gateway commands to

; Configure the Yaesu Fusion Partner
; Audio format is AMBE 72 bit
; Audio format is IMBE 88 bit
[YSF]
address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
txPort = 42500                  ; Port to send AMBE TLV frames to (export)
rxPort = 43500                  ; Port to listen on (import)
txWidePort = 42500        ; Port to send IMBE TLV frames to for YSFw (export)
fallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
exportTG = 1234                    ; Which TG to export
slot = 2                        ; Export slot
RemotePort = 6073        ; Port to send Gateway commands to

2261 - 2280 of 9595