Date   

Re: Dashboard #best_practices

Steve N4IRS
 

The DVSwitch Server dashboard is in a apt package for buster. dvswitch-dashboard
The reflector dashboard is here <https://github.com/N4IRS/MMDVM-Install/tree/master/P25/P25Reflector-Dashboard> When I get time I'll make it a stand alone git repository.

Steve

On 2/16/2021 12:30 PM, Tom wrote:
OK, I'll put P25Reflector dashboard on my P25-AB / P25Reflector Pi.  When I get my rebuild of the DMR-AB working, I'll add the DVSwitch dashboard on that Pi.

Is there a repo for these dashboards?


Re: Dashboard #best_practices

Tom
 

OK, I'll put P25Reflector dashboard on my P25-AB / P25Reflector Pi.  When I get my rebuild of the DMR-AB working, I'll add the DVSwitch dashboard on that Pi.

Is there a repo for these dashboards?


Re: Dashboard #best_practices

Steve N4IRS
 

Anything is possible as far as breaking something. I can't say other then backup.
The P25Reflector dashboard shows you what is happening on the reflector.
The DVSwitch dashboard is more MMDVM_Bridge centric.

On 2/16/2021 12:11 PM, Tom wrote:
Could either one be installed over a working P25-AB / P25Reflector unit with out breaking it (or reinstalling)?


Re: Dashboard #best_practices

Tom
 

Could either one be installed over a working P25-AB / P25Reflector unit with out breaking it (or reinstalling)?


Re: Dashboard #best_practices

Tom
 

What is possible? 
What will the P25Reflector dashboard give me and what will the DVSwitch dashboard give? 


Re: Dashboard #best_practices

Steve N4IRS
 

Are you looking for a P25Reflector dashboard or adding the DVSwitch Server dashboard?

On 2/16/2021 11:55 AM, Tom wrote:
Can I add a dashboard to my P25-AB (and reflector) without messing up a very well working server?  To date, I've simply tailing the logfile for reflector connections. 

Is there a repo to only add the dashboard?

Thanks,
Tom / K5TRA


Re: DVSwitch Dashboard

Steve N4IRS
 

2=*7345479#      ;this is what I added  trying to get my Allstar 46141 to connect to Node 45479

hmmm,
I think this should be:
2=*345479#      ;this is what I added  trying to get my Allstar 46141 to connect to Node 45479

Unless You have *73 defined as something else

On 2/16/2021 11:53 AM, Peter Buckley via groups.io wrote:
Thanks Steve - TCP port 8080 it is and now forwarding through my firewall.

Q.)  How to make Allstar automatically connect to another Allstar Node at boot up?
(below rpt.conf doesn't work)

I edited  rpt.conf

Under [46141]
startup_macro_delay=20
startup_macro = *52

[macro46141]
2=*7345479#      ;this is what I added  trying to get my Allstar 46141 to connect to Node 45479
;1 = *32011#
;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#
;3 = *32001*32011*32050*32030*32060#


Dashboard #best_practices

Tom
 

Can I add a dashboard to my P25-AB (and reflector) without messing up a very well working server?  To date, I've simply tailing the logfile for reflector connections. 

Is there a repo to only add the dashboard?

Thanks,
Tom / K5TRA


Re: DVSwitch Dashboard

Peter Buckley
 

Thanks Steve - TCP port 8080 it is and now forwarding through my firewall.

Q.)  How to make Allstar automatically connect to another Allstar Node at boot up?
(below rpt.conf doesn't work)

I edited  rpt.conf

Under [46141]
startup_macro_delay=20
startup_macro = *52

[macro46141]
2=*7345479#      ;this is what I added  trying to get my Allstar 46141 to connect to Node 45479
;1 = *32011#
;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#
;3 = *32001*32011*32050*32030*32060#


MMDVM Bridge and YSF Reflector don´t talk to each other

Uli
 

Thats a special one for Steve...
I´m debugging a MMDVM_Bridge and YSF Reflector combo.
Worked before but not anymore.

I have another installation of a MMDVM_Bridge and YSF Reflector combo that works fine. The only difference is: on my setup MMDVM_Bridge and YSF Reflector are running on two separate raspberrys
Here, both share one machine. I have carefully checked the MMDVM_Bridge.ini and DVSwitch.ini  and they seem to be ok.

I have compared the MMDVM and YSF Reflector live logs of my setup with the single raspi setup and I can see Incoming connections to the YSF Reflector and also from BM TG to the MMDVM_bridge, they look fine and identical to the ones on my setup.
The differrence is: The two beasts don´t want to talk to each other..
I see the incoming connection in the livelog of the YSF Reflector but nothing in the MMDVM Bridge log and vice versa.

How do I get the two to talk together?

regards

Uli


Re: DVSwitch Dashboard

Steve N4IRS
 

Pete,
Good to hear you are working.
The audio is on TCP port 8080

The "TG WB2QGZ" is a bug, that should be fixed in the image but I guess not. I'll look at it and make sure the bug is filed in a update.

Steve N4IRS

On 2/16/2021 10:02 AM, Peter Buckley via groups.io wrote:
Steve etal - got your new image file working.

Just using the DMR <---> Allstar gateway only.  Rpi3 has no Radio attached.

Please see attached JPG.
Re:  RX Monitor on DVSwitch Dashboard

Audio works from web page when I'm on the same IP Subnet.
Q.)  What TCP? UDP Ports do I need to forward at my Firewall so I can hear the audio when I'm at a remote location.

Second Q.)  Please see attached JPG -
Re:  Gateway Activity and Target
Q.)  I have no clue where DVSwitch Dashboard is getting the WB2QGZ call.  What config file is this coming from?
I have a simple setup - BM/TG 31085 and Allstar connection to 45479 (this is working)
Thanks to all.
Great work on that new image file, Steve.
73s  -pete  N0ECT


DVSwitch Dashboard

Peter Buckley
 

Steve etal - got your new image file working.

Just using the DMR <---> Allstar gateway only.  Rpi3 has no Radio attached.

Please see attached JPG.
Re:  RX Monitor on DVSwitch Dashboard

Audio works from web page when I'm on the same IP Subnet.
Q.)  What TCP? UDP Ports do I need to forward at my Firewall so I can hear the audio when I'm at a remote location.

Second Q.)  Please see attached JPG -
Re:  Gateway Activity and Target
Q.)  I have no clue where DVSwitch Dashboard is getting the WB2QGZ call.  What config file is this coming from?
I have a simple setup - BM/TG 31085 and Allstar connection to 45479 (this is working)
Thanks to all.
Great work on that new image file, Steve.
73s  -pete  N0ECT


Re: Second instances

Steve Siesel [K4KSA]
 

Thank You!

On Tue, Feb 16, 2021 at 6:30 AM Steve N4IRS <szingman@...> wrote:
Yes, That will work

On 2/15/21 11:09 AM, Steve Siesel [K4KSA] wrote:

To have second instances of AB, MB, md380-emu, Do you just copy the directories to where you want the second instances? Then modify and rename the existing .service files? This is to send to Broadcasify



Re: Second instances

Steve N4IRS
 

Yes, That will work

On 2/15/21 11:09 AM, Steve Siesel [K4KSA] wrote:

To have second instances of AB, MB, md380-emu, Do you just copy the directories to where you want the second instances? Then modify and rename the existing .service files? This is to send to Broadcasify



Re: DMR AB with c-bridge access #analog_bridge

Steve N4IRS
 

Inline:

On 2/15/21 10:49 PM, Tom wrote:
Steve,
I'm starting on a new DMR-AB to replace that old one from 5 years ago. I have ASL installed and prepped for the AB/MMDVMB/. . .  I pllan to reuse the DV3000 AMBE Pi hat instead of MD380 emulation. I have three questions at this point:
1) What do I need to do in the installation to opt for the DV3000, and to have it communicate with AB?
It in AB.ini
; Information for DV3000 hardware decoder
;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)
;   Use top server and port if using AMBEServer
;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)
;   Did you run AMBETest4.py before using this?
[DV3000]
address = 127.0.0.1                   ; IP address of AMBEServer
rxPort = 2460                         ; Port of AMBEServer
; address = /dev/ttyUSB0              ; Device of DV3000U on this machine
; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)
; serial = true                       ; Use serial=true for direct connect or serial=false for AMBEServer

2) I want to maintain the c-bridge communications capability on this new build.  How does HBLink fit into the inter-module communications scheme?
HBLink does not communicate with c-Bridge it's MMDVM / OpenBridge connectivity only You need DMRlink (IPSC_Bridge and HB_Bridge (or MMDVM_Bridge)
3) Is there a repo installation for HBLink?
<https://github.com/HBLink-org/hblink3>

Thanks,
Tom / K5TRA


DMR AB with c-bridge access #analog_bridge

Tom
 

Steve,
I'm starting on a new DMR-AB to replace that old one from 5 years ago. I have ASL installed and prepped for the AB/MMDVMB/. . .  I pllan to reuse the DV3000 AMBE Pi hat instead of MD380 emulation. I have three questions at this point:
1) What do I need to do in the installation to opt for the DV3000, and to have it communicate with AB?
2) I want to maintain the c-bridge communications capability on this new build.  How does HBLink fit into the inter-module communications scheme?
3) Is there a repo installation for HBLink?

Thanks,
Tom / K5TRA


Re: Unable to locate package dvswitch-server

Steve, N9VW
 

I suppose I ran the wrong update script after I built the image. It looks like it is all loading now.
Let the learning begin!

Thanks,
Steve, N9VW


Re: Unable to locate package dvswitch-server

Steve N4IRS
 

Steve,
I see this:
Hit:1 http://dvswitch.org/ASL_Repository stretch InRelease
Which tells me something attempted to install a older version of AllStar
edit the file /etc/apt/sources.list.d/

change all occurrences of stretch to buster
apt update
apt install dvswitch-server

On 2/15/2021 12:01 PM, Steve, N9VW wrote:
Steve,
I have a fresh, updated version of Buster. I installed everything per the above directions and get the following:

pi@raspberrypi:~ $ wget http://dvswitch.org/buster
--2021-02-15 08:57:35--  http://dvswitch.org/buster
Resolving dvswitch.org (dvswitch.org)... 44.103.34.4
Connecting to dvswitch.org (dvswitch.org)|44.103.34.4|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 1831 (1.8K)
Saving to: ‘buster’

buster                                  100%[===============================================================================>]   1.79K  --.-KB/s    in 0s

2021-02-15 08:57:35 (29.4 MB/s) - ‘buster’ saved [1831/1831]

pi@raspberrypi:~ $ sudo -s
root@raspberrypi:/home/pi# ls
Bookshelf  buster  Desktop  Documents  Downloads  Music  Pictures  Public  Templates  Videos
root@raspberrypi:/home/pi# chmod +x buster
root@raspberrypi:/home/pi# ./buster
The Repository file already exists, exiting
root@raspberrypi:/home/pi# apt-get update
Hit:1 http://dvswitch.org/ASL_Repository stretch InRelease
Get:2 http://packages.microsoft.com/repos/code stable InRelease [10.4 kB]
Get:3 http://raspbian.raspberrypi.org/raspbian buster InRelease [15.0 kB]
Get:4 http://archive.raspberrypi.org/debian buster InRelease [32.8 kB]
Get:5 http://packages.microsoft.com/repos/code stable/main arm64 Packages [13.9 kB]
Get:6 http://packages.microsoft.com/repos/code stable/main amd64 Packages [13.2 kB]
Get:7 http://packages.microsoft.com/repos/code stable/main armhf Packages [13.7 kB]
Get:8 http://archive.raspberrypi.org/debian buster/main armhf Packages [364 kB]
Fetched 463 kB in 3s (152 kB/s)
Reading package lists... Done
root@raspberrypi:/home/pi# apt-get install dvswitch-server
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Unable to locate package dvswitch-server
root@raspberrypi:/home/pi#
root@raspberrypi:/home/pi#
root@raspberrypi:/home/pi# uname -a
Linux raspberrypi 5.10.11-v7+ #1399 SMP Thu Jan 28 12:06:05 GMT 2021 armv7l GNU/Linux
root@raspberrypi:/home/pi#

What am I missing???

All I am really wanting to do is IPSC <-> Analog_Bridge <-> DV3000 <-> icecast (or similar streaming service)

73 de Steve, N9VW


Re: Unable to locate package dvswitch-server

Steve, N9VW
 

Steve,
I have a fresh, updated version of Buster. I installed everything per the above directions and get the following:

pi@raspberrypi:~ $ wget http://dvswitch.org/buster
--2021-02-15 08:57:35--  http://dvswitch.org/buster
Resolving dvswitch.org (dvswitch.org)... 44.103.34.4
Connecting to dvswitch.org (dvswitch.org)|44.103.34.4|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 1831 (1.8K)
Saving to: ‘buster’

buster                                  100%[===============================================================================>]   1.79K  --.-KB/s    in 0s

2021-02-15 08:57:35 (29.4 MB/s) - ‘buster’ saved [1831/1831]

pi@raspberrypi:~ $ sudo -s
root@raspberrypi:/home/pi# ls
Bookshelf  buster  Desktop  Documents  Downloads  Music  Pictures  Public  Templates  Videos
root@raspberrypi:/home/pi# chmod +x buster
root@raspberrypi:/home/pi# ./buster
The Repository file already exists, exiting
root@raspberrypi:/home/pi# apt-get update
Hit:1 http://dvswitch.org/ASL_Repository stretch InRelease
Get:2 http://packages.microsoft.com/repos/code stable InRelease [10.4 kB]
Get:3 http://raspbian.raspberrypi.org/raspbian buster InRelease [15.0 kB]
Get:4 http://archive.raspberrypi.org/debian buster InRelease [32.8 kB]
Get:5 http://packages.microsoft.com/repos/code stable/main arm64 Packages [13.9 kB]
Get:6 http://packages.microsoft.com/repos/code stable/main amd64 Packages [13.2 kB]
Get:7 http://packages.microsoft.com/repos/code stable/main armhf Packages [13.7 kB]
Get:8 http://archive.raspberrypi.org/debian buster/main armhf Packages [364 kB]
Fetched 463 kB in 3s (152 kB/s)
Reading package lists... Done
root@raspberrypi:/home/pi# apt-get install dvswitch-server
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Unable to locate package dvswitch-server
root@raspberrypi:/home/pi#
root@raspberrypi:/home/pi#
root@raspberrypi:/home/pi# uname -a
Linux raspberrypi 5.10.11-v7+ #1399 SMP Thu Jan 28 12:06:05 GMT 2021 armv7l GNU/Linux
root@raspberrypi:/home/pi#

What am I missing???

All I am really wanting to do is IPSC <-> Analog_Bridge <-> DV3000 <-> icecast (or similar streaming service)

73 de Steve, N9VW


Second instances

Steve Siesel [K4KSA]
 

To have second instances of AB, MB, md380-emu, Do you just copy the directories to where you want the second instances? Then modify and rename the existing .service files? This is to send to Broadcasify

961 - 980 of 9532