Date   

HBLink <-> IPSC2 error message

Thierry F4EWI
 

Hello,
In first we install DMRLink for Motorola repeater and it's works perfectly
Now we try to install a link between HBLink and IPSC2 for MMDVM repeater. We have the following error message:

INFO 2018-04-09 21:14:18,912 (MASTER-1) Repeater Logging in with Radio ID: 208477, 92.184.97.127:51263 
INFO 2018-04-09 21:14:18,912 (MASTER-1) Sent Challenge Response to 208477 for login: 2089173234 
INFO 2018-04-09 21:14:18,995 (MASTER-1) Client 208477 has completed the login exchange successfully 
INFO 2018-04-09 21:14:19,760 (MASTER-1) Client F4EWI (208477) has sent repeater configuration 
ERROR 2018-04-09 21:14:19,846 (MASTER-1) Unrecognized command. Raw HBP PDU: 5250544f00032e5d20 
ERROR 2018-04-09 21:14:29,838 (MASTER-1) Unrecognized command. Raw HBP PDU: 5250544f00032e5d20 

can anyone help me?


Re: DMRlink issue

Themis Floros SV4QXF
 

Hi Cort , my configuration is basic for the moment , i try to find way to connect with IPSC2  , at first tests i try to use  DMRLink as MASTER <-> IPSC2 and take the upper msg error , now try as PEER <-> IPSC2 and show to working and stay connected. Next steps is to configure the bridge.

Maybe all config is wrong

[IPSC2_GR_PEER]
ENABLED: True
RADIO_ID: 202091
IP:
PORT: 50000
ALIVE_TIMER: 5
MAX_MISSED: 20
PEER_OPER: True
IPSC_MODE: DIGITAL
TS1_LINK: True
TS2_LINK: True
CSBK_CALL: False
RCM: False
CON_APP: False
XNL_CALL: False
XNL_MASTER: False
DATA_CALL: True
VOICE_CALL: True
MASTER_PEER: False
AUTH_ENABLED: True
AUTH_KEY: 7XX57XX5XX
MASTER_IP: 81.4.XXX.XXX
MASTER_PORT: 56002
GROUP_HANGTIME: 5


Re: DMRlink issue

Cort N0MJS <n0mjs@...>
 

It means the peer with radio ID 1202001 is not registered with DMRlink, but is sending keep-alives. Most likely the peer *believes* it is registered, but it is not.

With incomplete topology information about your network setup and no additional logs, configurations, etc., that’s about all I can tell you.

On Apr 6, 2018, at 11:06 AM, Themis Floros SV4QXF <xsystem@...> wrote:

Hello guys , its possible to explain me why a connection between IPSC2 and DMRlink take this msg at logs :

WARNING 2018-04-06 18:51:02,002 (IPSC_GR_MASTER) Master Keep-Alive Request Received from *UNREGISTERED* peer 1202001, 10.168.56.1:56001

...the connection from ipsc2 side after first registration (with disabled auth) has counting down from 20-to-1 and next reset it.

Cort Buffington
785-865-7206


DMRlink issue

Themis Floros SV4QXF
 

Hello guys , its possible to explain me why a connection between IPSC2 and DMRlink take this msg at logs :

WARNING 2018-04-06 18:51:02,002 (IPSC_GR_MASTER) Master Keep-Alive Request Received from *UNREGISTERED* peer 1202001, 10.168.56.1:56001

...the connection from ipsc2 side after first registration (with disabled auth) has counting down from 20-to-1 and next reset it.


Re: Call routing cluster

Petr Frank, OK2ZAR
 

Hi Steve,

Thanks for explanation.

I finally won the battle some couple minutes ago so i'm very excited to play more during the weekend ;-)

73, Petr OK2ZAR.


Re: Call routing cluster

Steve N4IRS
 

Petr,
Questions are no problem. We need to do a better job with the Wiki.
The short answers to your example: You will start hb_confbridge.py, it will start hblink for you.

hblink.py is the lowest level log the HB "stack" it handles connecting to servers and accepting connections from clients. It defines logging and table lookups for subscriber IDs etc. On it's own it does vary little BUT is is required. The first step in setting up a hblink application is to make sure hblink.py is properly configured. hb_confbridge will sub-class hblink.py Think of it as hb_confbridge calls hblink when it needs to communicate with Servers and Clients. (Don't shoot me guys)

You do not define repeaters or client s that can connect to the Master (Server). You define a a "place" where the repeater can connect to. in the sample config, that is [MASTER-1] Multiple clients can connect to that Master or you can define multiple Master sections.

To connect hblink to a BM master, you connect as a client. Setup the client the same way you would in MMDVMHost.

Hope this helps.

73, Steve N4IRS    

On 4/6/2018 4:20 AM, Petr Frank wrote:
Hi guys,

i've tried to play a bit and have some questions. It means dummy questions and I'd like to ask like an idiot :-)

  • I guess each *.PY script is a module so in case i want to use hb_confbridge do i have to start hblink.py + hb_confbridge.py or is particular module called/load by main script hblink.py?
  • Where and how i can define repeaters (including repeater ID, etc...) able to connect to the master
  • What's about requirements to connect hblink to DMR+ or BrandMeister as a repeater? I've tried but it ended in logging loop without success login.


Lets see my configuration

hblink.cfg:
[MASTER-1]
MODE: MASTER
ENABLED: True
REPEAT: True
EXPORT_AMBE: False
IP:
PORT: 62031
PASSPHRASE: passw0rd
GROUP_HANGTIME: 5

[REPEATER-1]
MODE: CLIENT
ENABLED: False
EXPORT_AMBE: False
IP:
PORT: 54001
MASTER_IP: 92.43.29.198
MASTER_PORT: 62031
PASSPHRASE: passw0rd
CALLSIGN: OK0TEST
RADIO_ID: 230116
RX_FREQ: 439000000
TX_FREQ: 431000000
TX_POWER: 25
COLORCODE: 1
SLOTS: 1
LATITUDE: 38.0000
LONGITUDE: -095.0000
HEIGHT: 75
LOCATION: Anywhere, EU
DESCRIPTION: This is a cool repeater
URL: www.w1abc.org
SOFTWARE_ID: 20170620
PACKAGE_ID: MMDVM_HBlink
GROUP_HANGTIME: 5
OPTIONS:

hb_confbridge_rules.py:

BRIDGES = {
    'WORLDWIDE': [
            {'SYSTEM': 'MASTER-1',    'TS': 1, 'TGID': 1,    'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'ON',  'ON': [2,], 'OFF': [9,10]},
            {'SYSTEM': 'REPEATER-1',    'TS': 1, 'TGID': 3100, 'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'ON',  'ON': [2,], 'OFF': [9,10]},
        ],
    'ENGLISH': [
            {'SYSTEM': 'MASTER-1',    'TS': 1, 'TGID': 13,   'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [3,], 'OFF': [8,10]},
            {'SYSTEM': 'REPEATER-1',    'TS': 1, 'TGID': 13,   'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [3,], 'OFF': [8,10]},
        ],
    'STATEWIDE': [
            {'SYSTEM': 'MASTER-1',    'TS': 2, 'TGID': 3129, 'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [4,], 'OFF': [7,10]},
            {'SYSTEM': 'REPEATER-1',    'TS': 2, 'TGID': 3129, 'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [4,], 'OFF': [7,10]},
        ],
    'PRAHA': [
            {'SYSTEM': 'MASTER-1',    'TS': 1, 'TGID': 111, 'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [5,], 'OFF': [6,10]},
            {'SYSTEM': 'REPEATER-1',    'TS': 1, 'TGID': 111, 'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [5,], 'OFF': [6,10]},
        ]
}

talkgroup_ids.csv:

1,MARC Wordlwide
2,Local 2
3,MARC North America
111,Praha

talkgroup_ids.json is deleted once hb_confbridge.py starts and it returns:
DEBUG 2018-04-06 09:58:41,802 Logging system started, anything from here on gets logged
INFO 2018-04-06 09:58:41,803 Routing bridges file found and bridges imported
ERROR: Conference bridges found for system not configured main configuration

Unfortunately i don't know what else i can check and modify.

Sorry for dummy questions but i was unable to find-out answers in wiki.

Petr, OK2ZAR.


Re: Call routing cluster

Petr Frank, OK2ZAR
 

Hi guys,

i've tried to play a bit and have some questions. It means dummy questions and I'd like to ask like an idiot :-)

  • I guess each *.PY script is a module so in case i want to use hb_confbridge do i have to start hblink.py + hb_confbridge.py or is particular module called/load by main script hblink.py?
  • Where and how i can define repeaters (including repeater ID, etc...) able to connect to the master
  • What's about requirements to connect hblink to DMR+ or BrandMeister as a repeater? I've tried but it ended in logging loop without success login.


Lets see my configuration

hblink.cfg:
[MASTER-1]
MODE: MASTER
ENABLED: True
REPEAT: True
EXPORT_AMBE: False
IP:
PORT: 62031
PASSPHRASE: passw0rd
GROUP_HANGTIME: 5

[REPEATER-1]
MODE: CLIENT
ENABLED: False
EXPORT_AMBE: False
IP:
PORT: 54001
MASTER_IP: 92.43.29.198
MASTER_PORT: 62031
PASSPHRASE: passw0rd
CALLSIGN: OK0TEST
RADIO_ID: 230116
RX_FREQ: 439000000
TX_FREQ: 431000000
TX_POWER: 25
COLORCODE: 1
SLOTS: 1
LATITUDE: 38.0000
LONGITUDE: -095.0000
HEIGHT: 75
LOCATION: Anywhere, EU
DESCRIPTION: This is a cool repeater
URL: www.w1abc.org
SOFTWARE_ID: 20170620
PACKAGE_ID: MMDVM_HBlink
GROUP_HANGTIME: 5
OPTIONS:

hb_confbridge_rules.py:

BRIDGES = {
    'WORLDWIDE': [
            {'SYSTEM': 'MASTER-1',    'TS': 1, 'TGID': 1,    'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'ON',  'ON': [2,], 'OFF': [9,10]},
            {'SYSTEM': 'REPEATER-1',    'TS': 1, 'TGID': 3100, 'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'ON',  'ON': [2,], 'OFF': [9,10]},
        ],
    'ENGLISH': [
            {'SYSTEM': 'MASTER-1',    'TS': 1, 'TGID': 13,   'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [3,], 'OFF': [8,10]},
            {'SYSTEM': 'REPEATER-1',    'TS': 1, 'TGID': 13,   'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [3,], 'OFF': [8,10]},
        ],
    'STATEWIDE': [
            {'SYSTEM': 'MASTER-1',    'TS': 2, 'TGID': 3129, 'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [4,], 'OFF': [7,10]},
            {'SYSTEM': 'REPEATER-1',    'TS': 2, 'TGID': 3129, 'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [4,], 'OFF': [7,10]},
        ],
    'PRAHA': [
            {'SYSTEM': 'MASTER-1',    'TS': 1, 'TGID': 111, 'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [5,], 'OFF': [6,10]},
            {'SYSTEM': 'REPEATER-1',    'TS': 1, 'TGID': 111, 'ACTIVE': True, 'TIMEOUT': 2, 'TO_TYPE': 'NONE', 'ON': [5,], 'OFF': [6,10]},
        ]
}

talkgroup_ids.csv:

1,MARC Wordlwide
2,Local 2
3,MARC North America
111,Praha

talkgroup_ids.json is deleted once hb_confbridge.py starts and it returns:
DEBUG 2018-04-06 09:58:41,802 Logging system started, anything from here on gets logged
INFO 2018-04-06 09:58:41,803 Routing bridges file found and bridges imported
ERROR: Conference bridges found for system not configured main configuration

Unfortunately i don't know what else i can check and modify.

Sorry for dummy questions but i was unable to find-out answers in wiki.

Petr, OK2ZAR.


Re: DVSwitch Status update

Steve N4IRS
 

Yes it will. The plan is to decouple to Vocoders from Analog_Bridge and provide a method for someone to build the Vocoder separately.

On 4/5/2018 8:57 AM, Matthew 2E0SIP wrote:

Hi All,

This is an exciting update, thanks to all for the hard work.

One question, will the emulator run as a separate process, so it can be emulated on X86_64, without running Analog_Bridge in its entirety in an emulator? 

Cheers



Re: DVSwitch Status update

Matthew 2E0SIP
 

Hi All,

This is an exciting update, thanks to all for the hard work.

One question, will the emulator run as a separate process, so it can be emulated on X86_64, without running Analog_Bridge in its entirety in an emulator? 

Cheers


Re: ASL>DStar dummy repeater crashing

G7RPG - Peter Kendall
 

Thanks, Steve. I'll sit tight for a bit.

73

Peter


On 02/04/18 22:08, Steve N4IRS wrote:
DummyRepeater is not long for this world. We will be replacing it wit a simpler lighter solution. See my post a few weeks ago.

Steve

On 04/02/2018 04:46 PM, G7RPG - Peter Kendall wrote:

Hi Steve,

I'm running ASL on x68 debian on an esx vm, likewise I've got an x68 vm debian box that I've tried running dummy repeater on. I've got a couple of ambe devices NWDR Thumb DV and a DV-MEGA ambe300+carrier board makes no difference.

I tried running dummy repeater and ircddbgateway on a Pi and again the same thing happens.

My ASL > DMR is rock solid!

73

Peter


On 02/04/18 21:29, Steven Blackford wrote:
Hi Peter,
  ASL<->D-Star is rock solid for me.    It's been running currently for several weeks without a reboot or restart.  When I had my node setup to bridge over to DMR, i had an issue with the DMR->ASL going to sleep until someone keyed up on ASL.  Then it would start working again.  On your PI are you running the new ASL software or are you running the HamVOIP software?  What hardware are you using to do the transcoding?    I'm currently using a PiDV, but have used an original Blue DV-Dongle & a ThumbDV as well.   73 de K4SQI!

Steve, K4SQI


On Mon, Apr 2, 2018 at 4:23 PM, G7RPG - Peter Kendall <g7rpg@...> wrote:
Hi I wonder if anyone who is using dummy repeater to link to allstar has
a problem where dstar > asl stops working randomly sometimes an hour
sometimes a day or so. ASL > dstar is never a problem.

Restarting dummy repeater fixes the problem.

I've tried this on a VM and Rpi and get the same results.


73
Peter
G7RPG









--
-----
Steve, kb7sqi@...




Re: ASL>DStar dummy repeater crashing

Steve N4IRS
 

DummyRepeater is not long for this world. We will be replacing it wit a simpler lighter solution. See my post a few weeks ago.

Steve

On 04/02/2018 04:46 PM, G7RPG - Peter Kendall wrote:

Hi Steve,

I'm running ASL on x68 debian on an esx vm, likewise I've got an x68 vm debian box that I've tried running dummy repeater on. I've got a couple of ambe devices NWDR Thumb DV and a DV-MEGA ambe300+carrier board makes no difference.

I tried running dummy repeater and ircddbgateway on a Pi and again the same thing happens.

My ASL > DMR is rock solid!

73

Peter


On 02/04/18 21:29, Steven Blackford wrote:
Hi Peter,
  ASL<->D-Star is rock solid for me.    It's been running currently for several weeks without a reboot or restart.  When I had my node setup to bridge over to DMR, i had an issue with the DMR->ASL going to sleep until someone keyed up on ASL.  Then it would start working again.  On your PI are you running the new ASL software or are you running the HamVOIP software?  What hardware are you using to do the transcoding?    I'm currently using a PiDV, but have used an original Blue DV-Dongle & a ThumbDV as well.   73 de K4SQI!

Steve, K4SQI


On Mon, Apr 2, 2018 at 4:23 PM, G7RPG - Peter Kendall <g7rpg@...> wrote:
Hi I wonder if anyone who is using dummy repeater to link to allstar has
a problem where dstar > asl stops working randomly sometimes an hour
sometimes a day or so. ASL > dstar is never a problem.

Restarting dummy repeater fixes the problem.

I've tried this on a VM and Rpi and get the same results.


73
Peter
G7RPG









--
-----
Steve, kb7sqi@...



Re: ASL>DStar dummy repeater crashing

Steven Blackford
 

Hey Peter,
   Sounds like we need to compare notes then. :-)  I've sent you an email off list.  I'd be happy to try to help you get the ASL<->D-Star side working if I can.  Just a quick question.  Are you using an AMBEserver in the mix or are you going directly to the AMBE device with DummyRepeater?  73 de K4SQI.

Steve, K4SQI

On Mon, Apr 2, 2018 at 4:46 PM, G7RPG - Peter Kendall <g7rpg@...> wrote:

Hi Steve,

I'm running ASL on x68 debian on an esx vm, likewise I've got an x68 vm debian box that I've tried running dummy repeater on. I've got a couple of ambe devices NWDR Thumb DV and a DV-MEGA ambe300+carrier board makes no difference.

I tried running dummy repeater and ircddbgateway on a Pi and again the same thing happens.

My ASL > DMR is rock solid!

73

Peter


On 02/04/18 21:29, Steven Blackford wrote:
Hi Peter,
  ASL<->D-Star is rock solid for me.    It's been running currently for several weeks without a reboot or restart.  When I had my node setup to bridge over to DMR, i had an issue with the DMR->ASL going to sleep until someone keyed up on ASL.  Then it would start working again.  On your PI are you running the new ASL software or are you running the HamVOIP software?  What hardware are you using to do the transcoding?    I'm currently using a PiDV, but have used an original Blue DV-Dongle & a ThumbDV as well.   73 de K4SQI!

Steve, K4SQI


On Mon, Apr 2, 2018 at 4:23 PM, G7RPG - Peter Kendall <g7rpg@...> wrote:
Hi I wonder if anyone who is using dummy repeater to link to allstar has
a problem where dstar > asl stops working randomly sometimes an hour
sometimes a day or so. ASL > dstar is never a problem.

Restarting dummy repeater fixes the problem.

I've tried this on a VM and Rpi and get the same results.


73
Peter
G7RPG









--
-----
Steve, kb7sqi@...




--
-----
Steve, kb7sqi@...


Re: ASL>DStar dummy repeater crashing

G7RPG - Peter Kendall
 

Hi Steve,

I'm running ASL on x68 debian on an esx vm, likewise I've got an x68 vm debian box that I've tried running dummy repeater on. I've got a couple of ambe devices NWDR Thumb DV and a DV-MEGA ambe300+carrier board makes no difference.

I tried running dummy repeater and ircddbgateway on a Pi and again the same thing happens.

My ASL > DMR is rock solid!

73

Peter


On 02/04/18 21:29, Steven Blackford wrote:
Hi Peter,
  ASL<->D-Star is rock solid for me.    It's been running currently for several weeks without a reboot or restart.  When I had my node setup to bridge over to DMR, i had an issue with the DMR->ASL going to sleep until someone keyed up on ASL.  Then it would start working again.  On your PI are you running the new ASL software or are you running the HamVOIP software?  What hardware are you using to do the transcoding?    I'm currently using a PiDV, but have used an original Blue DV-Dongle & a ThumbDV as well.   73 de K4SQI!

Steve, K4SQI


On Mon, Apr 2, 2018 at 4:23 PM, G7RPG - Peter Kendall <g7rpg@...> wrote:
Hi I wonder if anyone who is using dummy repeater to link to allstar has
a problem where dstar > asl stops working randomly sometimes an hour
sometimes a day or so. ASL > dstar is never a problem.

Restarting dummy repeater fixes the problem.

I've tried this on a VM and Rpi and get the same results.


73
Peter
G7RPG









--
-----
Steve, kb7sqi@...


Re: ASL>DStar dummy repeater crashing

Steven Blackford
 

Hi Peter,
  ASL<->D-Star is rock solid for me.    It's been running currently for several weeks without a reboot or restart.  When I had my node setup to bridge over to DMR, i had an issue with the DMR->ASL going to sleep until someone keyed up on ASL.  Then it would start working again.  On your PI are you running the new ASL software or are you running the HamVOIP software?  What hardware are you using to do the transcoding?    I'm currently using a PiDV, but have used an original Blue DV-Dongle & a ThumbDV as well.   73 de K4SQI!

Steve, K4SQI


On Mon, Apr 2, 2018 at 4:23 PM, G7RPG - Peter Kendall <g7rpg@...> wrote:
Hi I wonder if anyone who is using dummy repeater to link to allstar has
a problem where dstar > asl stops working randomly sometimes an hour
sometimes a day or so. ASL > dstar is never a problem.

Restarting dummy repeater fixes the problem.

I've tried this on a VM and Rpi and get the same results.


73
Peter
G7RPG









--
-----
Steve, kb7sqi@...


ASL>DStar dummy repeater crashing

G7RPG - Peter Kendall
 

Hi I wonder if anyone who is using dummy repeater to link to allstar has
a problem where dstar > asl stops working randomly sometimes an hour
sometimes a day or so. ASL > dstar is never a problem.

Restarting dummy repeater fixes the problem.

I've tried this on a VM and Rpi and get the same results.


73
Peter
G7RPG


Re: Call routing cluster

Peter M0NWI
 

Petr,

I do exactly that using using bridge.py and define all the slots / TG / repeaters' in the bridge_rules.py, you can define them as always on, it user activated, UA can be made to switch on a specific transmission group or time.

Have a look at bridge_rules sample, its super flexible!

73,
Peter

Sent from Outlook
From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of Petr Frank <iogroups@...>
Sent: 28 March 2018 18:49:51
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] Call routing cluster
 
Thanks Corey. I'll test it and maybe come back with another question ;-)


Re: Call routing cluster

Petr Frank, OK2ZAR
 

Thanks Corey. I'll test it and maybe come back with another question ;-)


Re: Call routing cluster

Corey Dean N3FE <n3fe@...>
 

I should have done my homework before responding...  You can run the hb confbridge and do that.  Here is the sample config.

https://github.com/n0mjs710/HBlink/blob/master/hb_confbridge_rules-SAMPLE.py

Corey N3FE

On Wed, Mar 28, 2018 at 1:27 PM, Petr Frank <iogroups@...> wrote:
Hi guys,

i've test HBlink approx 3 months ago and it really worked. ;-) Fantastic work. I used modified config sample a bit during my testing. I've some questions based on my experiences.

Is possible to create some clusters? It means to have group of repeaters assigned to specified talk group and when somebody talks on the TG then all assigned repeaters are transmitting but non-assigned repeaters are idle.
How i can define permanent linked group(s) for each repeater? Is possible to have on-demand groups?
Are DMR private calls supported? I haven't been able to establish private call via HBlink.

73 de Petr, OK2ZAR.



Re: Call routing cluster

Corey Dean N3FE <n3fe@...>
 

I know using dmrlink you define it in the confbrdge and each connection has its own login.  I haven't looked to see if there is a hb conference bridge but I am assuming it would work the same way if there is such a thing.

Corey  N3FE

On Wed, Mar 28, 2018 at 1:27 PM, Petr Frank <iogroups@...> wrote:
Hi guys,

i've test HBlink approx 3 months ago and it really worked. ;-) Fantastic work. I used modified config sample a bit during my testing. I've some questions based on my experiences.

Is possible to create some clusters? It means to have group of repeaters assigned to specified talk group and when somebody talks on the TG then all assigned repeaters are transmitting but non-assigned repeaters are idle.
How i can define permanent linked group(s) for each repeater? Is possible to have on-demand groups?
Are DMR private calls supported? I haven't been able to establish private call via HBlink.

73 de Petr, OK2ZAR.



Call routing cluster

Petr Frank, OK2ZAR
 

Hi guys,

i've test HBlink approx 3 months ago and it really worked. ;-) Fantastic work. I used modified config sample a bit during my testing. I've some questions based on my experiences.

Is possible to create some clusters? It means to have group of repeaters assigned to specified talk group and when somebody talks on the TG then all assigned repeaters are transmitting but non-assigned repeaters are idle.
How i can define permanent linked group(s) for each repeater? Is possible to have on-demand groups?
Are DMR private calls supported? I haven't been able to establish private call via HBlink.

73 de Petr, OK2ZAR.

8961 - 8980 of 9882