Date   

Re: Macro result was 512 #analog_bridge

Geoff
 

Steve,

I am running a multi user server (DVLink). I have no problems using the macro to change DMR servers using other user's account.
To give you an insight of what I have done to my server, I have recently updated dvswitch.sh to v1.6.1 from v1.5.9 and also updated MMDVM_Bridge to the latest v.1.6.8.
I have not updated  other users' dvswitch.sh but updated MMDVM_Bridge to the latest.
So only difference is that as a main user myself I am using dvswitch v1.6.1 and the rest of the users are still using dvswitch.sh v 1.5.9
I wonder if I need to revert to dvswitch v1.5.9.
Hope that helps.


Re: Macro result was 512 #analog_bridge

Geoff
 

Steve,

I ran and got "macro result was 256".
There was no file named out.txt  in /tmp.


Re: Macro result was 512 #analog_bridge

Steve N4IRS
 

Geff,
Let's verify that D is executing what you think it is.
in dvsm.macro change D to:
D=sudo /opt/Analog_Bridge/dvswitch.sh "version ALL >/tmp/out.txt"

Run the macro and see if you get the 512 result. If not, what is the contents of /tmp/out.txt

On 9/16/21 6:12 AM, Geoff wrote:
Thank you for coming back to me.
The following are my macro settings in dvsm.macro

A=sudo /opt/Analog_Bridge/dvswitch.sh tune "1961@...:62031"
B=sudo /opt/Analog_Bridge/dvswitch.sh tune "1961@...:62031"
C=sudo /opt/Analog_Bridge/dvswitch.sh tune "PASSWORD@...:55555:StartRef=4570;RelinkTime=120;UserLink=1;TS2_1=450;TS2_2=518"
D=sudo /opt/Analog_Bridge/dvswitch.sh tune "PASSWORD@...:55555:StartRef=4570;RelinkTime=120;UserLink=1;TS1_1=5;TS2_1=505;TS2_2=3802"

If I issue the command at the prompt, it connects to the desired DMR+ server as shown below :-
~$ sudo /opt/Analog_Bridge/dvswitch.sh tune "1961@...:55555:StartRef=4570;RelinkTime=120;UserLink=1;TS1_1=5;TS2_1=505;TS2_2=3802"

However, when I issue macro "*D", I get "macro result was 512" and can not connect to the server.

Thank you.


Re: Macro result was 512 #analog_bridge

Geoff
 

On Thu, Sep 16, 2021 at 08:12 PM, Geoff wrote:
~$ sudo /opt/Analog_Bridge/dvswitch.sh tune "1961@...:55555:StartRef=4570;RelinkTime=120;UserLink=1;TS1_1=5;TS2_1=505;TS2_2=3802"
Correction :-

~$ sudo /opt/Analog_Bridge/dvswitch.sh tune "PASSWORD@...:55555:StartRef=4570;RelinkTime=120;UserLink=1;TS1_1=5;TS2_1=505;TS2_2=3802"


Re: Macro result was 512 #analog_bridge

Geoff
 

Thank you for coming back to me.
The following are my macro settings in dvsm.macro

A=sudo /opt/Analog_Bridge/dvswitch.sh tune "1961@...:62031"
B=sudo /opt/Analog_Bridge/dvswitch.sh tune "1961@...:62031"
C=sudo /opt/Analog_Bridge/dvswitch.sh tune "PASSWORD@...:55555:StartRef=4570;RelinkTime=120;UserLink=1;TS2_1=450;TS2_2=518"
D=sudo /opt/Analog_Bridge/dvswitch.sh tune "PASSWORD@...:55555:StartRef=4570;RelinkTime=120;UserLink=1;TS1_1=5;TS2_1=505;TS2_2=3802"

If I issue the command at the prompt, it connects to the desired DMR+ server as shown below :-
~$ sudo /opt/Analog_Bridge/dvswitch.sh tune "1961@...:55555:StartRef=4570;RelinkTime=120;UserLink=1;TS1_1=5;TS2_1=505;TS2_2=3802"

However, when I issue macro "*D", I get "macro result was 512" and can not connect to the server.

Thank you.


Re: P25 to DMR troubles. error at MMDVM_Bridge - Cannot bind UDP address, err: 98 -and- Cannot open listener port 34103

Steve N4IRS
 

The path would be:
P25Reflector <-> P25Gateway <-> MMDVM_Bridge <->Analog_Bridge_P25 <-> Analog_Bridge_DMR <-> MMDVM_Bridge <-> DMR network This would use a single instance of MMDVM_Bridge.
Analog_Bridge_P25 [AMBE_AUDIO] should point to the UDP ports defined in DVSwitch.ini for P25 and Analog_Bridge_DMR [AMBE_AUDIO] should point to the UDP ports defined in DVSwitch.ini for DMR.

Show your DVSwitch.ini

On 9/15/21 10:06 PM, Todd, KB7RQQ wrote:
I have a P25 reflector running and it works great.  Decided to bridge to our DMR talk group. so I have P25Reflector --> P25Gateway --> Analog_Bridge_DMR --> Analog_Bridge_P25 --> MMDVM_Bridge.  Reflector is working fine, checked both AB's for port accuracy.  When I fire them up in that order, I get an error on MMDVM_Bridge.

This is cut down to the end....

M: 2021-09-16 01:32:00.439 P25, Opening INI file: DVSwitch.ini
M: 2021-09-16 01:32:00.440 P25, Setting [P25] address -> 127.0.0.1
M: 2021-09-16 01:32:00.440 P25, Setting [P25] txPort -> 34100
M: 2021-09-16 01:32:00.440 P25, Setting [P25] rxPort -> 34103
M: 2021-09-16 01:32:00.440 P25, Setting [P25] slot -> 2
M: 2021-09-16 01:32:00.440 P25, Setting [P25] RemotePort -> 6074
E: 2021-09-16 01:32:00.440 Cannot bind the UDP address, err: 98
F: 2021-09-16 01:32:00.440 P25, Can not open listener port 34103

34103 would be the rxPort of P25 side of Analog_Bridge_P25.ini    Not sure what configs would be helpful so I'll start with P25Bridge/AB_DMR/ABP25

Anyone see anything that stands out as whacky?

--P25Bridge.ini
[General]
Callsign=KB7RQQ
RptAddress=127.0.0.1
RptPort=32010
LocalPort=42020
Daemon=0
 
[Id Lookup]
Name=/var/lib/mmdvm/DMRIds.dat
Time=24
 
[Voice]
Enabled=1
Language=en_US
Directory=./Audio
 
[Log]
# Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
DisplayLevel=1
FileLevel=2
FilePath=/var/log/mmdvm
FileRoot=P25Gateway
 
[Network]
Port=42010
HostsFile1=/etc/P25Hosts.txt
HostsFile2=./private/P25Hosts.txt
ReloadTime=60
ParrotAddress=127.0.0.1
ParrotPort=42011
Startup=31655
InactivityTimeout=10
Debug=0
 
[Remote Commands]
Enable=0
Port=6074



--Analog_Bridge_DMR.ini

; Analog_Bridge configuration file.
;   This file should be placed in either /etc or it can be
;   supplied as a path on the Analog_Bridge command line.
 
; The best way to think of this file is that there are two main sections, the USRP (analog audio) and
; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.
; As you might expect, the reverse direction is defined too.
 
; Analog_Bridge supports include files. More on this later...
include = dvsm.macro
; include = asl.macro
 
; General Section describes settings for Analog_Bridge itself.
[GENERAL]
logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
 
; Metadata management
exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)
transferRootDir = /tmp ; Export database files to USRP partner
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data
 
; General vocoder setup information
decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found
useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server
 
pcmPort = 2222                          ; UDP port to send to the WebProxy
 
; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address = 127.0.0.1                     ; IP address of xx_Bridge
txPort = 31100                          ; Transmit TLV frames to partner on this port
rxPort = 31103                          ; Listen for TLV frames from partner on this port
ambeMode = DMR                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS = 2000                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)
 
; The metadata below is used when ASL is the source since it does not have any concept of digital modes
gatewayDmrId = 3153376                  ; ID to use when transmitting from Analog_Bridge 7 digit ID
repeaterID = 315337613                  ; ID of source repeater 7 digit ID plus 2 digit SSID 
txTg = 31655                                ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge
txTs = 1                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge
colorCode = 1                           ; Color Code to assign DMR frames
 
; Information for USRP channel driver.  This interface uses PCM to transfer audio information
; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected
; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, 
; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.
;   When using ASL, this matches the rpt.conf ASL file with a setting like:
;   rxchannel = usrp/127.0.0.1:34001:32001
;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch
;   each instance with its own ini file.
[USRP]
address = 127.0.0.1                     ; IP address of USRP partner (Analog_Reflector, Allstar/Asterisk or another Analog_Bridge)
txPort = 32001                          ; Transmit USRP frames on this port
rxPort = 34001                          ; Listen for USRP frames on this port
usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)
usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)
tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
 
[MACROS]
 
; Where the macros are
; xxxx=yyyy
; xxxx is the dial string to match
; yyyy is the command line to execute
 
; xxxx must be preceded by a *
; xxxx can be any string (alphanumeric)
; yyyy is the command to execute
; yyyy will replace xxxx in the dial string
; arguments follow the macro name with a # delimiter
 
; For example using macro "5678" above would look like:
; *5678#9876
 
; Which would invoke:
; echo 9876
 
; Information for DV3000 hardware decoder
;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)
;   Use top server and port if using AMBEServer
;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)
;   Did you run AMBETest4.py before using this?
[DV3000]
address = 127.0.0.1                   ; IP address of AMBEServer
rxPort = 2460                         ; Port of AMBEServer
; address = /dev/ttyUSB0              ; Device of DV3000U on this machine
; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)
; serial = true                       ; Use serial=true for direct connect or serial=false for AMBEServer




--Analog_Bridge_P25

; Analog_Bridge configuration file.
;   This file should be placed in either /etc or it can be
;   supplied as a path on the Analog_Bridge command line.
 
; The best way to think of this file is that there are two main sections, the USRP (analog audio) and
; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.
; As you might expect, the reverse direction is defined too.
 
; Analog_Bridge supports include files. More on this later...
include = dvsm.macro
; include = asl.macro
 
; General Section describes settings for Analog_Bridge itself.
[GENERAL]
logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
 
; Metadata management
exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)
transferRootDir = /tmp ; Export database files to USRP partner
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data
 
; General vocoder setup information
decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found
useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server
 
pcmPort = 2222                          ; UDP port to send to the WebProxy
 
; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address = 127.0.0.1                     ; IP address of xx_Bridge
txPort = 34100                          ; Transmit TLV frames to partner on this port
rxPort = 34103                          ; Listen for TLV frames from partner on this port
ambeMode = P25                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS = 2000                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)
 
; The metadata below is used when ASL is the source since it does not have any concept of digital modes
gatewayDmrId = 3153376                  ; ID to use when transmitting from Analog_Bridge 7 digit ID
repeaterID = 315337613                  ; ID of source repeater 7 digit ID plus 2 digit SSID 
txTg = 31655                            ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge
txTs = 1                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge
colorCode = 1                           ; Color Code to assign DMR frames
 
; Information for USRP channel driver.  This interface uses PCM to transfer audio information
; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected
; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, 
; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.
;   When using ASL, this matches the rpt.conf ASL file with a setting like:
;   rxchannel = usrp/127.0.0.1:34001:32001
;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch
;   each instance with its own ini file.
[USRP]
address = 127.0.0.1                     ; IP address of USRP partner (Analog_Reflector, Allstar/Asterisk or another Analog_Bridge)
txPort = 34001                          ; Transmit USRP frames on this port
rxPort = 32001                          ; Listen for USRP frames on this port
usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)
usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)
tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
 
[MACROS]
 
; Where the macros are
; xxxx=yyyy
; xxxx is the dial string to match
; yyyy is the command line to execute
 
; xxxx must be preceded by a *
; xxxx can be any string (alphanumeric)
; yyyy is the command to execute
; yyyy will replace xxxx in the dial string
; arguments follow the macro name with a # delimiter
 
; For example using macro "5678" above would look like:
; *5678#9876
 
; Which would invoke:
; echo 9876
 
; Information for DV3000 hardware decoder
;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)
;   Use top server and port if using AMBEServer
;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)
;   Did you run AMBETest4.py before using this?
[DV3000]
address = 127.0.0.1                   ; IP address of AMBEServer
rxPort = 2460                         ; Port of AMBEServer
; address = /dev/ttyUSB0              ; Device of DV3000U on this machine
; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)
; serial = true                       ; Use serial=true for direct connect or serial=false for AMBEServer
 
 


Re: Macro result was 512 #analog_bridge

Steve N4IRS
 

Please post your A, B, C and D macros.

On 9/15/21 10:41 PM, Geoff wrote:
I have modified dvsm.macro file so I can switch from one DMR server to another.
There are 4 servers that I was able to switch at will and the setup has been working quite well until lately.
By pressing macro key A, B, C or D I was able to switch from a DMR server to another and so forth.
However, recently when I press D to change to another DMR server, I get "Macro result was 512".
I don't know what it means and how to go about fixing it.
Can anyone shed some light on this matter, please?

Thank you.


Re: P25 to DMR troubles. error at MMDVM_Bridge - Cannot bind UDP address, err: 98 -and- Cannot open listener port 34103

Steve N4IRS
 



On 9/15/21 10:06 PM, Todd, KB7RQQ wrote:
I have a P25 reflector running and it works great.  Decided to bridge to our DMR talk group. so I have P25Reflector --> P25Gateway --> Analog_Bridge_DMR --> Analog_Bridge_P25 --> MMDVM_Bridge.  Reflector is working fine, checked both AB's for port accuracy.  When I fire them up in that order, I get an error on MMDVM_Bridge.

This is cut down to the end....

M: 2021-09-16 01:32:00.439 P25, Opening INI file: DVSwitch.ini
M: 2021-09-16 01:32:00.440 P25, Setting [P25] address -> 127.0.0.1
M: 2021-09-16 01:32:00.440 P25, Setting [P25] txPort -> 34100
M: 2021-09-16 01:32:00.440 P25, Setting [P25] rxPort -> 34103
M: 2021-09-16 01:32:00.440 P25, Setting [P25] slot -> 2
M: 2021-09-16 01:32:00.440 P25, Setting [P25] RemotePort -> 6074
E: 2021-09-16 01:32:00.440 Cannot bind the UDP address, err: 98
F: 2021-09-16 01:32:00.440 P25, Can not open listener port 34103

34103 would be the rxPort of P25 side of Analog_Bridge_P25.ini    Not sure what configs would be helpful so I'll start with P25Bridge/AB_DMR/ABP25

Anyone see anything that stands out as whacky?

--P25Bridge.ini
[General]
Callsign=KB7RQQ
RptAddress=127.0.0.1
RptPort=32010
LocalPort=42020
Daemon=0
 
[Id Lookup]
Name=/var/lib/mmdvm/DMRIds.dat
Time=24
 
[Voice]
Enabled=1
Language=en_US
Directory=./Audio
 
[Log]
# Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
DisplayLevel=1
FileLevel=2
FilePath=/var/log/mmdvm
FileRoot=P25Gateway
 
[Network]
Port=42010
HostsFile1=/etc/P25Hosts.txt
HostsFile2=./private/P25Hosts.txt
ReloadTime=60
ParrotAddress=127.0.0.1
ParrotPort=42011
Startup=31655
InactivityTimeout=10
Debug=0
 
[Remote Commands]
Enable=0
Port=6074



--Analog_Bridge_DMR.ini

; Analog_Bridge configuration file.
;   This file should be placed in either /etc or it can be
;   supplied as a path on the Analog_Bridge command line.
 
; The best way to think of this file is that there are two main sections, the USRP (analog audio) and
; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.
; As you might expect, the reverse direction is defined too.
 
; Analog_Bridge supports include files. More on this later...
include = dvsm.macro
; include = asl.macro
 
; General Section describes settings for Analog_Bridge itself.
[GENERAL]
logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
 
; Metadata management
exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)
transferRootDir = /tmp ; Export database files to USRP partner
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data
 
; General vocoder setup information
decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found
useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server
 
pcmPort = 2222                          ; UDP port to send to the WebProxy
 
; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address = 127.0.0.1                     ; IP address of xx_Bridge
txPort = 31100                          ; Transmit TLV frames to partner on this port
rxPort = 31103                          ; Listen for TLV frames from partner on this port
ambeMode = DMR                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS = 2000                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)
 
; The metadata below is used when ASL is the source since it does not have any concept of digital modes
gatewayDmrId = 3153376                  ; ID to use when transmitting from Analog_Bridge 7 digit ID
repeaterID = 315337613                  ; ID of source repeater 7 digit ID plus 2 digit SSID 
txTg = 31655                                ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge
txTs = 1                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge
colorCode = 1                           ; Color Code to assign DMR frames
 
; Information for USRP channel driver.  This interface uses PCM to transfer audio information
; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected
; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, 
; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.
;   When using ASL, this matches the rpt.conf ASL file with a setting like:
;   rxchannel = usrp/127.0.0.1:34001:32001
;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch
;   each instance with its own ini file.
[USRP]
address = 127.0.0.1                     ; IP address of USRP partner (Analog_Reflector, Allstar/Asterisk or another Analog_Bridge)
txPort = 32001                          ; Transmit USRP frames on this port
rxPort = 34001                          ; Listen for USRP frames on this port
usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)
usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)
tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
 
[MACROS]
 
; Where the macros are
; xxxx=yyyy
; xxxx is the dial string to match
; yyyy is the command line to execute
 
; xxxx must be preceded by a *
; xxxx can be any string (alphanumeric)
; yyyy is the command to execute
; yyyy will replace xxxx in the dial string
; arguments follow the macro name with a # delimiter
 
; For example using macro "5678" above would look like:
; *5678#9876
 
; Which would invoke:
; echo 9876
 
; Information for DV3000 hardware decoder
;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)
;   Use top server and port if using AMBEServer
;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)
;   Did you run AMBETest4.py before using this?
[DV3000]
address = 127.0.0.1                   ; IP address of AMBEServer
rxPort = 2460                         ; Port of AMBEServer
; address = /dev/ttyUSB0              ; Device of DV3000U on this machine
; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)
; serial = true                       ; Use serial=true for direct connect or serial=false for AMBEServer




--Analog_Bridge_P25

; Analog_Bridge configuration file.
;   This file should be placed in either /etc or it can be
;   supplied as a path on the Analog_Bridge command line.
 
; The best way to think of this file is that there are two main sections, the USRP (analog audio) and
; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.
; As you might expect, the reverse direction is defined too.
 
; Analog_Bridge supports include files. More on this later...
include = dvsm.macro
; include = asl.macro
 
; General Section describes settings for Analog_Bridge itself.
[GENERAL]
logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
 
; Metadata management
exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)
transferRootDir = /tmp ; Export database files to USRP partner
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data
 
; General vocoder setup information
decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found
useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server
 
pcmPort = 2222                          ; UDP port to send to the WebProxy
 
; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address = 127.0.0.1                     ; IP address of xx_Bridge
txPort = 34100                          ; Transmit TLV frames to partner on this port
rxPort = 34103                          ; Listen for TLV frames from partner on this port
ambeMode = P25                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS = 2000                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)
 
; The metadata below is used when ASL is the source since it does not have any concept of digital modes
gatewayDmrId = 3153376                  ; ID to use when transmitting from Analog_Bridge 7 digit ID
repeaterID = 315337613                  ; ID of source repeater 7 digit ID plus 2 digit SSID 
txTg = 31655                            ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge
txTs = 1                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge
colorCode = 1                           ; Color Code to assign DMR frames
 
; Information for USRP channel driver.  This interface uses PCM to transfer audio information
; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected
; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, 
; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.
;   When using ASL, this matches the rpt.conf ASL file with a setting like:
;   rxchannel = usrp/127.0.0.1:34001:32001
;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch
;   each instance with its own ini file.
[USRP]
address = 127.0.0.1                     ; IP address of USRP partner (Analog_Reflector, Allstar/Asterisk or another Analog_Bridge)
txPort = 34001                          ; Transmit USRP frames on this port
rxPort = 32001                          ; Listen for USRP frames on this port
usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)
usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)
tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
 
[MACROS]
 
; Where the macros are
; xxxx=yyyy
; xxxx is the dial string to match
; yyyy is the command line to execute
 
; xxxx must be preceded by a *
; xxxx can be any string (alphanumeric)
; yyyy is the command to execute
; yyyy will replace xxxx in the dial string
; arguments follow the macro name with a # delimiter
 
; For example using macro "5678" above would look like:
; *5678#9876
 
; Which would invoke:
; echo 9876
 
; Information for DV3000 hardware decoder
;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)
;   Use top server and port if using AMBEServer
;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)
;   Did you run AMBETest4.py before using this?
[DV3000]
address = 127.0.0.1                   ; IP address of AMBEServer
rxPort = 2460                         ; Port of AMBEServer
; address = /dev/ttyUSB0              ; Device of DV3000U on this machine
; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)
; serial = true                       ; Use serial=true for direct connect or serial=false for AMBEServer
 
 


Macro result was 512 #analog_bridge

Geoff
 

I have modified dvsm.macro file so I can switch from one DMR server to another.
There are 4 servers that I was able to switch at will and the setup has been working quite well until lately.
By pressing macro key A, B, C or D I was able to switch from a DMR server to another and so forth.
However, recently when I press D to change to another DMR server, I get "Macro result was 512".
I don't know what it means and how to go about fixing it.
Can anyone shed some light on this matter, please?

Thank you.


P25 to DMR troubles. error at MMDVM_Bridge - Cannot bind UDP address, err: 98 -and- Cannot open listener port 34103

Todd, KB7RQQ
 

I have a P25 reflector running and it works great.  Decided to bridge to our DMR talk group. so I have P25Reflector --> P25Gateway --> Analog_Bridge_DMR --> Analog_Bridge_P25 --> MMDVM_Bridge.  Reflector is working fine, checked both AB's for port accuracy.  When I fire them up in that order, I get an error on MMDVM_Bridge.

This is cut down to the end....

M: 2021-09-16 01:32:00.439 P25, Opening INI file: DVSwitch.ini
M: 2021-09-16 01:32:00.440 P25, Setting [P25] address -> 127.0.0.1
M: 2021-09-16 01:32:00.440 P25, Setting [P25] txPort -> 34100
M: 2021-09-16 01:32:00.440 P25, Setting [P25] rxPort -> 34103
M: 2021-09-16 01:32:00.440 P25, Setting [P25] slot -> 2
M: 2021-09-16 01:32:00.440 P25, Setting [P25] RemotePort -> 6074
E: 2021-09-16 01:32:00.440 Cannot bind the UDP address, err: 98
F: 2021-09-16 01:32:00.440 P25, Can not open listener port 34103

34103 would be the rxPort of P25 side of Analog_Bridge_P25.ini    Not sure what configs would be helpful so I'll start with P25Bridge/AB_DMR/ABP25

Anyone see anything that stands out as whacky?

--P25Bridge.ini
[General]
Callsign=KB7RQQ
RptAddress=127.0.0.1
RptPort=32010
LocalPort=42020
Daemon=0
 
[Id Lookup]
Name=/var/lib/mmdvm/DMRIds.dat
Time=24
 
[Voice]
Enabled=1
Language=en_US
Directory=./Audio
 
[Log]
# Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
DisplayLevel=1
FileLevel=2
FilePath=/var/log/mmdvm
FileRoot=P25Gateway
 
[Network]
Port=42010
HostsFile1=/etc/P25Hosts.txt
HostsFile2=./private/P25Hosts.txt
ReloadTime=60
ParrotAddress=127.0.0.1
ParrotPort=42011
Startup=31655
InactivityTimeout=10
Debug=0
 
[Remote Commands]
Enable=0
Port=6074



--Analog_Bridge_DMR.ini

; Analog_Bridge configuration file.
;   This file should be placed in either /etc or it can be
;   supplied as a path on the Analog_Bridge command line.
 
; The best way to think of this file is that there are two main sections, the USRP (analog audio) and
; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.
; As you might expect, the reverse direction is defined too.
 
; Analog_Bridge supports include files. More on this later...
include = dvsm.macro
; include = asl.macro
 
; General Section describes settings for Analog_Bridge itself.
[GENERAL]
logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
 
; Metadata management
exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)
transferRootDir = /tmp ; Export database files to USRP partner
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data
 
; General vocoder setup information
decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found
useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server
 
pcmPort = 2222                          ; UDP port to send to the WebProxy
 
; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address = 127.0.0.1                     ; IP address of xx_Bridge
txPort = 31100                          ; Transmit TLV frames to partner on this port
rxPort = 31103                          ; Listen for TLV frames from partner on this port
ambeMode = DMR                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS = 2000                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)
 
; The metadata below is used when ASL is the source since it does not have any concept of digital modes
gatewayDmrId = 3153376                  ; ID to use when transmitting from Analog_Bridge 7 digit ID
repeaterID = 315337613                  ; ID of source repeater 7 digit ID plus 2 digit SSID 
txTg = 31655                                ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge
txTs = 1                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge
colorCode = 1                           ; Color Code to assign DMR frames
 
; Information for USRP channel driver.  This interface uses PCM to transfer audio information
; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected
; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, 
; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.
;   When using ASL, this matches the rpt.conf ASL file with a setting like:
;   rxchannel = usrp/127.0.0.1:34001:32001
;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch
;   each instance with its own ini file.
[USRP]
address = 127.0.0.1                     ; IP address of USRP partner (Analog_Reflector, Allstar/Asterisk or another Analog_Bridge)
txPort = 32001                          ; Transmit USRP frames on this port
rxPort = 34001                          ; Listen for USRP frames on this port
usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)
usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)
tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
 
[MACROS]
 
; Where the macros are
; xxxx=yyyy
; xxxx is the dial string to match
; yyyy is the command line to execute
 
; xxxx must be preceded by a *
; xxxx can be any string (alphanumeric)
; yyyy is the command to execute
; yyyy will replace xxxx in the dial string
; arguments follow the macro name with a # delimiter
 
; For example using macro "5678" above would look like:
; *5678#9876
 
; Which would invoke:
; echo 9876
 
; Information for DV3000 hardware decoder
;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)
;   Use top server and port if using AMBEServer
;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)
;   Did you run AMBETest4.py before using this?
[DV3000]
address = 127.0.0.1                   ; IP address of AMBEServer
rxPort = 2460                         ; Port of AMBEServer
; address = /dev/ttyUSB0              ; Device of DV3000U on this machine
; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)
; serial = true                       ; Use serial=true for direct connect or serial=false for AMBEServer




--Analog_Bridge_P25

; Analog_Bridge configuration file.
;   This file should be placed in either /etc or it can be
;   supplied as a path on the Analog_Bridge command line.
 
; The best way to think of this file is that there are two main sections, the USRP (analog audio) and
; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.
; As you might expect, the reverse direction is defined too.
 
; Analog_Bridge supports include files. More on this later...
include = dvsm.macro
; include = asl.macro
 
; General Section describes settings for Analog_Bridge itself.
[GENERAL]
logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
 
; Metadata management
exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)
transferRootDir = /tmp ; Export database files to USRP partner
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data
 
; General vocoder setup information
decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found
useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server
 
pcmPort = 2222                          ; UDP port to send to the WebProxy
 
; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address = 127.0.0.1                     ; IP address of xx_Bridge
txPort = 34100                          ; Transmit TLV frames to partner on this port
rxPort = 34103                          ; Listen for TLV frames from partner on this port
ambeMode = P25                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS = 2000                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)
 
; The metadata below is used when ASL is the source since it does not have any concept of digital modes
gatewayDmrId = 3153376                  ; ID to use when transmitting from Analog_Bridge 7 digit ID
repeaterID = 315337613                  ; ID of source repeater 7 digit ID plus 2 digit SSID 
txTg = 31655                            ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge
txTs = 1                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge
colorCode = 1                           ; Color Code to assign DMR frames
 
; Information for USRP channel driver.  This interface uses PCM to transfer audio information
; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected
; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, 
; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.
;   When using ASL, this matches the rpt.conf ASL file with a setting like:
;   rxchannel = usrp/127.0.0.1:34001:32001
;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch
;   each instance with its own ini file.
[USRP]
address = 127.0.0.1                     ; IP address of USRP partner (Analog_Reflector, Allstar/Asterisk or another Analog_Bridge)
txPort = 34001                          ; Transmit USRP frames on this port
rxPort = 32001                          ; Listen for USRP frames on this port
usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)
usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)
tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
 
[MACROS]
 
; Where the macros are
; xxxx=yyyy
; xxxx is the dial string to match
; yyyy is the command line to execute
 
; xxxx must be preceded by a *
; xxxx can be any string (alphanumeric)
; yyyy is the command to execute
; yyyy will replace xxxx in the dial string
; arguments follow the macro name with a # delimiter
 
; For example using macro "5678" above would look like:
; *5678#9876
 
; Which would invoke:
; echo 9876
 
; Information for DV3000 hardware decoder
;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)
;   Use top server and port if using AMBEServer
;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)
;   Did you run AMBETest4.py before using this?
[DV3000]
address = 127.0.0.1                   ; IP address of AMBEServer
rxPort = 2460                         ; Port of AMBEServer
; address = /dev/ttyUSB0              ; Device of DV3000U on this machine
; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)
; serial = true                       ; Use serial=true for direct connect or serial=false for AMBEServer
 
 


Re: DVSwitch.ini was not found #mmdvm_bridge

Komkit Listisard
 

Steve,

Got it working somehow.

I deleted the mmdvm_bridge4.service and re-entered again from scratch exactly as it was.   This time it work no issue.

I have no idea what was the problem!!!

The only thing I can think of was my editor "nona" must have inserted some strange hidden characters or something.  I have no clue.

root@xlx1:/lib/systemd/system# systemctl start mmdvm_bridge4
root@xlx1:/lib/systemd/system# systemctl status mmdvm_bridge4
● mmdvm_bridge4.service - MMDVM_Bridge Service 4
   Loaded: loaded (/lib/systemd/system/mmdvm_bridge4.service; disabled; vendor preset: enabled)
   Active: active (running) since Wed 2021-09-15 09:50:08 EDT; 3s ago
  Process: 8955 ExecStartPre=/bin/sh -c echo "Starting MMDVM_Bridge: [`date +%T.%3N`]" >> /var/log/netcheck (code=exited, status=0/SUCCESS)
 Main PID: 8959 (MMDVM_Bridge4)
    Tasks: 2 (limit: 1148)
   Memory: 27.4M
   CGroup: /system.slice/mmdvm_bridge4.service
           └─8959 /opt/MMDVM_Bridge4/MMDVM_Bridge4 /opt/MMDVM_Bridge4/MMDVM_Bridge4.ini
 
Sep 15 09:50:08 w3kit-xlx1 systemd[1]: Starting MMDVM_Bridge Service 4...
Sep 15 09:50:08 w3kit-xlx1 systemd[1]: Started MMDVM_Bridge Service 4.

73, Kit
 


Re: DVSwitch.ini was not found #mmdvm_bridge

Komkit Listisard
 

Steve,

Not sure,  haven't there  (yet).

For now, I will just use DVSwitch.ini in the /opt/MMDMV_Bridge4/ since DVSwitch.ini does not show up on the UDP ports listing anyway.   As long as MMDVM_bridge4 show up,  since I like to documenting things as I go, much easier for the house keeping.

I will try 5 when I have the need :)

Thank you for your help as always.

73, Kit


Re: DVSwitch.ini was not found #mmdvm_bridge

Steve N4IRS
 

OK,
And if you number it as 5, what happens?

On 9/15/2021 9:20 AM, Komkit Listisard via groups.io wrote:
Steve,

Since this is my 4th instance of MMDMV_Bridge. I just renamed them so it would be easier for me to chasing them down when I have an issue and much easier when I list the UDP ports, so I know who is who and who is using what port.

Not sure why with other three instances I do not have an issue.

73, Kit


Re: DVSwitch.ini was not found #mmdvm_bridge

Komkit Listisard
 

Steve,

Since this is my 4th instance of MMDMV_Bridge. I just renamed them so it would be easier for me to chasing them down when I have an issue and much easier when I list the UDP ports, so I know who is who and who is using what port.

Not sure why with other three instances I do not have an issue.

73, Kit


Re: DVSwitch.ini was not found #mmdvm_bridge

Steve N4IRS
 

I don't see anything wrong with your service..
That being said, since you set the workingdirectory and the execstart, why rename MMDVM_Bridge, MMDVM_Bridge.ini and DVSwitch.ini ?

Steve N4IRS

On 9/15/2021 8:36 AM, Komkit Listisard via groups.io wrote:
Here is the mmdvm_bridge4.service



[Unit]
Description=MMDVM_Bridge Service4
# Description=Place this file in /lib/systemd/system
# Description=N4IRS 09/10/2020
 
After=netcheck.service
Requires=netcheck.service
 
[Service]
Type=simple
Restart=always
RestartSec=3
Restart=on-abort
StandardOutput=null
WorkingDirectory=/opt/MMDVM_Bridge4
Environment=DVSwitch=/opt/MMDVM_Bridge4/DVSwitch4.ini
ExecStartPre = /bin/sh -c 'echo "Starting MMDVM_Bridge: [`date +%%T.%%3N`]" >> /var/log/netcheck'
ExecStart=/opt/MMDVM_Bridge4/MMDVM_Bridge4 /opt/MMDVM_Bridge4/MMDVM_Bridge4.ini
ExecReload=/bin/kill -HUP $MAINPID
KillMode=process
 
[Install]
WantedBy=multi-user.target


73, Kit
 


Re: DVSwitch.ini was not found #mmdvm_bridge

Komkit Listisard
 

Here is the mmdvm_bridge4.service



[Unit]
Description=MMDVM_Bridge Service4
# Description=Place this file in /lib/systemd/system
# Description=N4IRS 09/10/2020
 
After=netcheck.service
Requires=netcheck.service
 
[Service]
Type=simple
Restart=always
RestartSec=3
Restart=on-abort
StandardOutput=null
WorkingDirectory=/opt/MMDVM_Bridge4
Environment=DVSwitch=/opt/MMDVM_Bridge4/DVSwitch4.ini
ExecStartPre = /bin/sh -c 'echo "Starting MMDVM_Bridge: [`date +%%T.%%3N`]" >> /var/log/netcheck'
ExecStart=/opt/MMDVM_Bridge4/MMDVM_Bridge4 /opt/MMDVM_Bridge4/MMDVM_Bridge4.ini
ExecReload=/bin/kill -HUP $MAINPID
KillMode=process
 
[Install]
WantedBy=multi-user.target


73, Kit
 


Re: DVSwitch.ini was not found #mmdvm_bridge

Steve N4IRS
 

Show your complete mmdvm_bridge.service

On 9/15/2021 6:52 AM, Komkit Listisard via groups.io wrote:
Hello,

In mmdvm_bridge.service I set an environment to Environment=DVSwitch=/opt/MMDVM_Bridge4/DVSwitch4.ini

The file is there working directory is there.

But mmdvm_bridge4 log is telling the DVSWitch.ini was not found.  However I told it to look for DVSwitch4.ini. But it kept looking for DVSwitch.ini

But as soon as I copied DVSwitch4.ini to DVSwitch.ini without number 4, the mmdvm_bridge4 is happy like a pig in the mud, no issue no complaint.

What am I missing here? Why couldn't I use DVSwitch4.ini.

For the record.  I have DVSwitch1, 2 and 3 running of sepatate instances, they all working fine no issue.

This time with #4 all of the sudden I am having and issue, I could not figured it out. 

73, Kit


DVSwitch.ini was not found #mmdvm_bridge

Komkit Listisard
 

Hello,

In mmdvm_bridge.service I set an environment to Environment=DVSwitch=/opt/MMDVM_Bridge4/DVSwitch4.ini

The file is there working directory is there.

But mmdvm_bridge4 log is telling the DVSWitch.ini was not found.  However I told it to look for DVSwitch4.ini. But it kept looking for DVSwitch.ini

But as soon as I copied DVSwitch4.ini to DVSwitch.ini without number 4, the mmdvm_bridge4 is happy like a pig in the mud, no issue no complaint.

What am I missing here? Why couldn't I use DVSwitch4.ini.

For the record.  I have DVSwitch1, 2 and 3 running of sepatate instances, they all working fine no issue.

This time with #4 all of the sudden I am having and issue, I could not figured it out. 

73, Kit


Re: P25 North America reflector

 

I would love to help you, but I don’t know how to code Linux or pi or MMDVM.  But if there’s anything else I can do to help you Beta Test let me know.

David Coviello
AK4FD


Re: P25 North America reflector

Corey Dean N3FE
 

That sounds more like the packers are out of order.  Good luck finding that in the internet between point a and b.


On Sep 12, 2021, at 4:56 PM, AK4FD (David) via groups.io <AK4FD@...> wrote:

So this is a QSO that just took place on NA 10200.  These 2 operators apparently could hear each other just fine, but as you will hear on my end it sounds like digital garble.  And all of my other talkgroups work fine whether it be P25 or DMR, so it can’t be my settings that are off otherwise they would be off everywhere else not just this 1 Talkgroup...  I’m wondering if it’s possible one or some of these 150+ connected links either aren’t processing the data streams correctly or maybe there is a setting off somewhere on their end.  I don’t think it’s the North America server issue I really do think it’s an issue with one of the connected bridges/links.  But listen for yourself, I’ve attached the audio file to this message, it’s 1 minute long.  Hopefully that may help you guys in trying to figure out these audio issues everyone keeps reporting...
<20210912 162024.m4a>

61 - 80 of 9795