|
Re: Blocked DVS???
I use a ThumbDV (has an AMBE chip).
I use a ThumbDV (has an AMBE chip).
|
By
nh6bf
·
#10864
·
|
|
Re: Blocked DVS???
Actually there are no issues. If you use DVS with a hardware vocoder (AMBE) or an external Ambe Server or the like, the audio quality is very good. The only problem is if you use a sofware vocoder. In
Actually there are no issues. If you use DVS with a hardware vocoder (AMBE) or an external Ambe Server or the like, the audio quality is very good. The only problem is if you use a sofware vocoder. In
|
By
IK7VXC Mike
·
#10863
·
Edited
|
|
Re: Blocked DVS???
I'm curious, what are the issues DVS causes with these reflectors? I
run REF023, which is also a DPLus reflector, and a popular VK hub. I
don't want to block DVS (quite the opposite), but would
I'm curious, what are the issues DVS causes with these reflectors? I
run REF023, which is also a DPLus reflector, and a popular VK hub. I
don't want to block DVS (quite the opposite), but would
|
By
Tony Langdon
·
#10862
·
|
|
Blocked DVS???
"Your callsign has been logged on either REF001 or REF030 using the DVSwitch software.
This software is experimental and has caused problems on the busy reflectors. As a result, the administrators of
"Your callsign has been logged on either REF001 or REF030 using the DVSwitch software.
This software is experimental and has caused problems on the busy reflectors. As a result, the administrators of
|
By
nh6bf
·
#10861
·
|
|
PTT button on an Rfinder
Hey guys,
Hope everyone is doing well. Question, anyone on here running the
rfinder using dvswitch? I'm playing with 1, and am trying to get the
bottom PTT button on the rfinder to work with
Hey guys,
Hope everyone is doing well. Question, anyone on here running the
rfinder using dvswitch? I'm playing with 1, and am trying to get the
bottom PTT button on the rfinder to work with
|
By
Jed Barton
·
#10860
·
|
|
Re: Analog_Bridge - Multiple instances problem / AMBE reset
I have a HV/DVS setup that did core dumps at 3 days. Pulled the ThumbDV dongle out and it slowed the arrival of core dumps. Bought a 60w USB power supply on Amazon and so far, no core dumps. ( I am
I have a HV/DVS setup that did core dumps at 3 days. Pulled the ThumbDV dongle out and it slowed the arrival of core dumps. Bought a 60w USB power supply on Amazon and so far, no core dumps. ( I am
|
By
nh6bf
·
#10859
·
|
|
DVS dashboard: missing Analog_Bridge info
Hi Steve. I got 2 dvs servers running on 2 different machines. The older install in the dashboard page does not have the Analog_Bridge info box, while the later install has that. What files should I
Hi Steve. I got 2 dvs servers running on 2 different machines. The older install in the dashboard page does not have the Analog_Bridge info box, while the later install has that. What files should I
|
By
IK7VXC Mike
·
#10858
·
|
|
Re: Analog_Bridge - Multiple instances problem / AMBE reset
I had the opposite problem with my AMBE dongle. I couldn't get
AMBEserver to work, but serial works perfectly. I'm using a ThumbDV for
D-STAR transcoding with Analog_Bridge. Currently only
I had the opposite problem with my AMBE dongle. I couldn't get
AMBEserver to work, but serial works perfectly. I'm using a ThumbDV for
D-STAR transcoding with Analog_Bridge. Currently only
|
By
Tony Langdon
·
#10857
·
|
|
Re: Analog_Bridge - Multiple instances problem / AMBE reset
On Wed, Jun 15, 2022 at 05:30 PM, Steve N4IRS wrote:
Steve,
Thank you.. I'd tried removing the stanza, but not putting a non-existent device or /dev/null in.. This appears to be the solution!
Many
On Wed, Jun 15, 2022 at 05:30 PM, Steve N4IRS wrote:
Steve,
Thank you.. I'd tried removing the stanza, but not putting a non-existent device or /dev/null in.. This appears to be the solution!
Many
|
By
m7mjs@...
·
#10856
·
|
|
Re: Analog_Bridge - Multiple instances problem / AMBE reset
[DV3000]
;address = 127.0.0.1 ; IP address of AMBEServer
;rxPort = 2460 ; Port of AMBEServer
address = /dev/null ; Device of DV3000U
[DV3000]
;address = 127.0.0.1 ; IP address of AMBEServer
;rxPort = 2460 ; Port of AMBEServer
address = /dev/null ; Device of DV3000U
|
By
Steve N4IRS
·
#10855
·
|
|
Re: Analog_Bridge - Multiple instances problem / AMBE reset
What I appear to be dealing with, is even with the DV3000 stanza totally commented out, the DMR analog_bridge recognises and uses AMBEserver unless it's not running, in which case fall back mode kicks
What I appear to be dealing with, is even with the DV3000 stanza totally commented out, the DMR analog_bridge recognises and uses AMBEserver unless it's not running, in which case fall back mode kicks
|
By
m7mjs@...
·
#10854
·
|
|
Re: Analog_Bridge - Multiple instances problem / AMBE reset
Thanks for the tip. I have just run AMBEtest4.py and get a clean bill of health, and it works fine under AMBEserver... I'll shall try a powered hub to see if that improves anything, but I'm surprised
Thanks for the tip. I have just run AMBEtest4.py and get a clean bill of health, and it works fine under AMBEserver... I'll shall try a powered hub to see if that improves anything, but I'm surprised
|
By
m7mjs@...
·
#10853
·
|
|
Re: Analog_Bridge - Multiple instances problem / AMBE reset
The NW DV3000 is very sensitive to power issues. See <https://dvswitch.groups.io/g/main/wiki/21838>
The NW DV3000 is very sensitive to power issues. See <https://dvswitch.groups.io/g/main/wiki/21838>
|
By
Steve N4IRS
·
#10852
·
|
|
Re: Analog_Bridge - Multiple instances problem / AMBE reset
Unfortunately, it seems from a serial angle I'm just one step closer:
M: 2022-06-15 12:57:00.563 Setting [DV3000] address -> /dev/ThumbDV
M: 2022-06-15 12:57:00.563 Setting [DV3000] address -> baud =
Unfortunately, it seems from a serial angle I'm just one step closer:
M: 2022-06-15 12:57:00.563 Setting [DV3000] address -> /dev/ThumbDV
M: 2022-06-15 12:57:00.563 Setting [DV3000] address -> baud =
|
By
m7mjs@...
·
#10851
·
|
|
Re: Analog_Bridge - Multiple instances problem / AMBE reset
To add info as to why serial is not working, please see below. This is with pretty much boiler plate config and the user has access to dialout/tty groups.
AMBEserver works a treat, AMBEtest4.py does
To add info as to why serial is not working, please see below. This is with pretty much boiler plate config and the user has access to dialout/tty groups.
AMBEserver works a treat, AMBEtest4.py does
|
By
m7mjs@...
·
#10849
·
|
|
Re: Analog_Bridge - Multiple instances problem / AMBE reset
Hi Patrick
Yes, the vocoder and AMBEserver run on the same machine. I haven't managed to get serial working, oddly I get errors with DV3000 not found despite using the correct settings as per
Hi Patrick
Yes, the vocoder and AMBEserver run on the same machine. I haven't managed to get serial working, oddly I get errors with DV3000 not found despite using the correct settings as per
|
By
m7mjs@...
·
#10848
·
|
|
Re: Analog_Bridge - Multiple instances problem / AMBE reset
Is your hardware vocoder on the same machine running Analog_Bridge?
I recently set up a system that is pretty much exactly as you described, but A_B is communicating directly with the
Is your hardware vocoder on the same machine running Analog_Bridge?
I recently set up a system that is pretty much exactly as you described, but A_B is communicating directly with the
|
By
Patrick Perdue
·
#10847
·
|
|
Analog_Bridge - Multiple instances problem / AMBE reset
Hi all
I'm running DVSwitch packages on top of Rasbian Buster and attempting to run two versions of Analog Bridge simultaneously.
1) Configured to take D-Star via DV3000 and AMBEserver into
Hi all
I'm running DVSwitch packages on top of Rasbian Buster and attempting to run two versions of Analog Bridge simultaneously.
1) Configured to take D-Star via DV3000 and AMBEserver into
|
By
m7mjs@...
·
#10846
·
|
|
Re: Issues with communication between MMDVM_Bridge and Analog_Bridge
#analog_bridge
<https://dvswitch.groups.io/g/Analog-Reflector/files/Analog_Reflector.pdf>
<https://dvswitch.groups.io/g/Analog-Reflector/files/Analog_Reflector.pdf>
|
By
Steve N4IRS
·
#10845
·
|
|
Re: Issues with communication between MMDVM_Bridge and Analog_Bridge
#analog_bridge
Okay is there a tutorial or document you can point me to that shows me how to configure all of these to work together in harmony?
Okay is there a tutorial or document you can point me to that shows me how to configure all of these to work together in harmony?
|
By
Roger
·
#10844
·
|