main@DVSwitch.groups.io

Re: Strange announcement after each keyup after about a day of running

Connected.

By Chris WB4ULK · #1803 ·

Re: Strange announcement after each keyup after about a day of running

If you guys would reconnect to 2600 in transceive, the more noise the better. You will only go out on TG3166 and ASL 2600 On 7/2/2018 1:32 PM, Mike KB8JNM wrote:

By Steve N4IRS · #1802 ·

Re: Strange announcement after each keyup after about a day of running

I think the point I thought was obvious that perhaps is not that I was trying to make was that among any other activity you might be doing and telemetry issue could create that 'quick

By Mike KB8JNM · #1801 ·

Re: Strange announcement after each keyup after about a day of running

If you are getting the “blocked” message it takes approximately 60 minutes of no key ups to reset.

By Kevin Halton · #1800 ·

Re: Strange announcement after each keyup after about a day of running

Interesting. I disconnected the bridge node from my hub node. Let it sit there for awhile, connected back up and it isn't doing it any more. The thing is, if it is my node being blocked by BM, won't

By Chris WB4ULK · #1799 ·

Re: HBmonitor setup/Debian Stretch x86_64

Understood, thanks Cort. I'll continue to follow development and re-visit it at a later time. 73 Stephen K1LNX

By Stephen Brown - K1LNX · #1798 ·

Re: Strange announcement after each keyup after about a day of running

I: 2018-07-02 16:11:20.567 DMR, Begin TX: src=3148824 rpt=3148824 dst=114814 slot=2 cc=1 metadata=3148824 M: 2018-07-02 16:11:22.621 DMR, TX state = OFF M: 2018-07-02 16:11:25.912 DMR Slot 2, received

By KB5PBM · #1797 · Edited

Re: Strange announcement after each keyup after about a day of running

I think you need to wait some abount of time to be "UNFLAGGED" If all is well. Just my opinion. ...mike/kb8jnm On 7/2/2018 11:32 AM, Chris WB4ULK via Groups.Io wrote:

By Mike KB8JNM · #1796 ·

Re: HBmonitor setup/Debian Stretch x86_64

Answer for Stephen, but something I really want everyone to take note of: (warning: you’re not going to like this) I consider DMRmonitor and HBmonitor very poorly written, unstable, and they are, as

By Cort N0MJS <n0mjs@...> · #1795 ·

HBmonitor setup/Debian Stretch x86_64

Hi guys, Trying to setup HBmonitor (https://github.com/n0mjs710/HBmonitor) to play with, and while I think I've satisfied most of the dependencies through apt-get installing packages as needed,

By Stephen Brown - K1LNX · #1794 ·

Re: Strange announcement after each keyup after about a day of running

I reconnected the Bridge node to my hub node. I keyed up over DMR no prob, but when I keyed up the analog side, she started her same ol' rigamarole. LOL

By Chris WB4ULK · #1793 ·

Re: Strange announcement after each keyup after about a day of running

I did, I disconnected everyone to make sure it was 2600 that was blocked. Chasing it down now. On 7/2/2018 11:28 AM, Chris WB4ULK via Groups.Io wrote:

By Steve N4IRS · #1792 ·

Re: Strange announcement after each keyup after about a day of running

Ha! I finally dialed into your node and noticed I was disconnected. I reconnected and there it was. Lol Sorry about that, didn’t realize you must have observed it and disconnected me. Chris

By Chris WB4ULK · #1791 ·

Re: Strange announcement after each keyup after about a day of running

Steve, FYI, I did go in last night and correct my DMR ID info. I increased it with an SSID as advised and put my tg in my selfcare. Chris

By Chris WB4ULK · #1790 ·

Re: Strange announcement after each keyup after about a day of running

Everybody, take a breath. I do not think this issue is ASL configuration issue. I'll be honest, we do not think the hang settings in MMDVM_Bridge.ini have any effect. The first thing I want

By Steve N4IRS · #1789 ·

Re: Strange announcement after each keyup after about a day of running

Those of us who are having THIS specific problem would like to discuss THIS issue. Please don’t muddy the thread. Chris

By Chris WB4ULK · #1788 ·

Re: Strange announcement after each keyup after about a day of running

OFF LIST Steve, He was using a normal node config with his dvswitch attachment. I think he has changed it on my advise. ...mike/kb8jnm On 7/2/2018 10:08 AM, Steve

By Mike KB8JNM · #1787 ·

Re: Strange announcement after each keyup after about a day of running

You are reading words I did not write. This was a general statement in "avoidance of issues" And I used it in example. The announcement (if you read the earlier posts) is generated

By Mike KB8JNM · #1786 ·

Re: Strange announcement after each keyup after about a day of running

Ok. I am going to connect 47484 to 2600. It will be connected to my local tg we use on the machine as well. Chris

By Chris WB4ULK · #1785 ·

Re: Strange announcement after each keyup after about a day of running

Chris, You are correct. This is a issue with traffic from ASL -> DMR. As a test I have ASL 2600 connected to TG 3166 in transceive. I also have 2600 connected to 2135 (WAN) in RECEIVE only.

By Steve N4IRS · #1784 ·

Messages