Steve, Are you trying to run MMDVMHost while MMDVM_Bridge is running? If so, the issue is probably ports. MH and MB use a lot of the same ports etc. On 5/2/23 17:12, Steve Bosshard

I have hit a snag and need some pointers. Also I do hope this is an appropriate forum - Info is kinda short in this topic. My intent is to replace a Pi-3 with a PC running Debian 10 and connect a

I know that I'm resurfacing an old post, but lots of distractions (like everyone else, I know). However, I'm still not getting any updates with DVS or putty/apt update. Here are screenshots of both. I

Sorry, I misread the question. This is correct: ExecStart=/usr/bin/node /opt/Web_Proxy/proxy.js 8050 2222 You also need to change the web page in index.php On HamVoIP it

ExecStart=/usr/bin/node /opt/Web_Proxy/proxy.js 8050 2222 should be ExecStart=/usr/bin/node /opt/Web_Proxy/proxy.js 8050 On 4/29/23 22:44, VE3WVJ via groups.io wrote:

i am trying to change the port for RX Monitor to 8050 by editing "/lib/systemd/system/webproxy.service" when i set it to the new port and reboot the node, the RX Monitor doesnt work. When i press the

Think I found it (post from you under a different subject), but since you're talking about something I avoid like the plague, my assistance is going to be limited. Two things I

sudo -s will aloow it so you do not need to type sudo for each line On 4/27/2023 7:35 PM, Tony Langdon wrote:

thank you. yes, i did find out sudo was required. i still cannot hear anything on dvswitch mobile. based on the dvswitch dashboard pic i posted, can you determine if i am connected? i am lost at this

I suspect it's a permissions issue, so using sudo might be required, unless logged in as root. sudo nano /opt/MMDVM_Bridge/MMDVM_Bridge.ini On 28/4/23 12:00

thank you! i was able to make the proper changes, but not hearing anything when connected to world wide TG 91. i think i am connected? a screenshot is attached, which shows what i am seeing when i TX

you can use putty and cd /opt/MMDVM_bridge directory. then use nano MMDVM_bridge.ini when done use CTRL-X to exit and save it. On 4/27/2023 9:43 AM, trauts14 wrote:

What is the best way to edit MMDVM_Bridge.ini? WinSCP is not allowing me to overwrite or replace the file.

Hi, I am new around here so let me apologise in advance if this is a stupid question or has been covered before. I reached out to brandmeister via a ticket to establish an openbridge as there has been

If your using the terminal to install, see the commands in the text document attached. If you want to see the basic setup, check my video https://youtu.be/_6aDNP8vTJ8 Hope this helps

Milton, We need more information. What you are trying to do? Build a bridge? Use your computer to operate digital modes? Other? What type of hardware? PC? Raspberry Pi? Other? What distribution

Hello I am in need of a guide that can help me install dvswitch on my linux computer. I have used some information that I have found on the internet and doesn’t work for me. I don’t know if I am

Like others have said, treat HBlink3 as you would any other DMR network Analog_Bridge, MMDVM_Bridge and optionally, Analog_Reflector are the tools you need. I run a local DMR

Thanks Bob KC2CWT Carmel NY 10512 (914)497-5502

DVSwitch Mobile <-> Analog_Reflector <-> Analog_Bridge <-> MMDVM_Bridge <-> HBLink3 or DVSwitch Mobile <-> Analog_Bridge <-> MMDVM_Bridge <-> HBLink3