Date   

Re: C Bridge to P25 Reflector

Steve N4IRS
 

##################################              ################################
# IPSC_Bridge configuration file #              #
HB_Bridge configuration file #           
##################################              ################################

[DEFAULTS]                                      [DEFAULTS]
gateway = 127.0.0.1                            
gateway = 127.0.0.1                             
fromGatewayPort = 31000                        
toGatewayPort = 31000
toGatewayPort = 31003                          
fromGatewayPort = 31003                          


The above assumes you are not using those port number somewhere else. If you are, make the unique.
example: change 31000 to 31999 change 31003 to 31993

On 7/17/2018 2:38 PM, KD5DFB wrote:
Steve, I really appreciate your help! My apologies, but, I just can see it. 

On Tue, Jul 17, 2018 at 12:57 PM, Steve N4IRS <szingman@...> wrote:
dmrlink.cfg and hblink.cfg define their respective network connections. IPSC_Bridge.cfg and HB_Bridge.cfg define their respective Partner connections.

On 7/17/2018 1:55 PM, KD5DFB wrote:
Okay, let me take a step back and break it down again. 

So, IPSC_Bridge uses both dmrlink.cfg and IPSC_bridge.cfg.  The dmrlink.cfg defines the connection to the cbridge and I see it connected on the control center. IPSC_Bridge.cfg defines the connection to HB_Bridge. Is that defined in the HB_Bridge.cfg or hblink.cfg?

On Tue, Jul 17, 2018 at 12:44 PM, Steve N4IRS <szingman@...> wrote:
No,
You can use the same port number twice. I try to use the default port numbers where possible. Since you can't use a port twice, you will have to change something. 

On 7/17/2018 1:38 PM, KD5DFB wrote:
Ok, so let me see if I got it correct. So basically all 3 of them use the same port numbers just changing the TX and RX? 

IPSC_Bridge.cfg                     HB_Bridge.cfg                  Analog_Bridge.ini
fromgateway: 31100              fromGateway: 31103         from: 31100
toGateway: 31103                  toGateway: 31100            to: 31103

On Tue, Jul 17, 2018 at 10:00 AM, Steve N4IRS <szingman@...> wrote:


On 7/17/2018 10:51 AM, KD5DFB wrote:
Okay, making progress! I am stumped on the last piece. 

I am trying to figure out the connection between ipsc_bridge and hb_bridge. 

On ipsc_bridge, I have the dmrlink.cfg connecting to the cbridge and can see traffic from the cbridge in the log. Does the ipsc_bridge.cfg connect to hb_bridge.cfg?
Yes

On the hb_bridge I am a little confused. Does the hb_bridge.cfg connect to analog_bridge? Does the ambe need to match what is in analog_bridge?
Just like connecting any of the partners, TX to RX and RX to TX (or words to that effect) Analog_Bridge [AMBE_AUDIO] stanza points to the values in the HB_Bridge [DEFAULTS] stanza.

[AMBE]
EXPORT_IP: 127.0.0.1
EXPORT_PORT: 1234
Ignore these


On Mon, Jul 16, 2018, 21:02 Steve N4IRS <szingman@...> wrote:
I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.
 

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB

















Re: C Bridge to P25 Reflector

Michael KD5DFB
 

Steve, I really appreciate your help! My apologies, but, I just can see it. 

On Tue, Jul 17, 2018 at 12:57 PM, Steve N4IRS <szingman@...> wrote:
dmrlink.cfg and hblink.cfg define their respective network connections. IPSC_Bridge.cfg and HB_Bridge.cfg define their respective Partner connections.

On 7/17/2018 1:55 PM, KD5DFB wrote:
Okay, let me take a step back and break it down again. 

So, IPSC_Bridge uses both dmrlink.cfg and IPSC_bridge.cfg.  The dmrlink.cfg defines the connection to the cbridge and I see it connected on the control center. IPSC_Bridge.cfg defines the connection to HB_Bridge. Is that defined in the HB_Bridge.cfg or hblink.cfg?

On Tue, Jul 17, 2018 at 12:44 PM, Steve N4IRS <szingman@...> wrote:
No,
You can use the same port number twice. I try to use the default port numbers where possible. Since you can't use a port twice, you will have to change something. 

On 7/17/2018 1:38 PM, KD5DFB wrote:
Ok, so let me see if I got it correct. So basically all 3 of them use the same port numbers just changing the TX and RX? 

IPSC_Bridge.cfg                     HB_Bridge.cfg                  Analog_Bridge.ini
fromgateway: 31100              fromGateway: 31103         from: 31100
toGateway: 31103                  toGateway: 31100            to: 31103

On Tue, Jul 17, 2018 at 10:00 AM, Steve N4IRS <szingman@...> wrote:


On 7/17/2018 10:51 AM, KD5DFB wrote:
Okay, making progress! I am stumped on the last piece. 

I am trying to figure out the connection between ipsc_bridge and hb_bridge. 

On ipsc_bridge, I have the dmrlink.cfg connecting to the cbridge and can see traffic from the cbridge in the log. Does the ipsc_bridge.cfg connect to hb_bridge.cfg?
Yes

On the hb_bridge I am a little confused. Does the hb_bridge.cfg connect to analog_bridge? Does the ambe need to match what is in analog_bridge?
Just like connecting any of the partners, TX to RX and RX to TX (or words to that effect) Analog_Bridge [AMBE_AUDIO] stanza points to the values in the HB_Bridge [DEFAULTS] stanza.

[AMBE]
EXPORT_IP: 127.0.0.1
EXPORT_PORT: 1234
Ignore these


On Mon, Jul 16, 2018, 21:02 Steve N4IRS <szingman@...> wrote:
I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.
 

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB
















Re: C Bridge to P25 Reflector

Steve N4IRS
 

dmrlink.cfg and hblink.cfg define their respective network connections. IPSC_Bridge.cfg and HB_Bridge.cfg define their respective Partner connections.

On 7/17/2018 1:55 PM, KD5DFB wrote:
Okay, let me take a step back and break it down again. 

So, IPSC_Bridge uses both dmrlink.cfg and IPSC_bridge.cfg.  The dmrlink.cfg defines the connection to the cbridge and I see it connected on the control center. IPSC_Bridge.cfg defines the connection to HB_Bridge. Is that defined in the HB_Bridge.cfg or hblink.cfg?

On Tue, Jul 17, 2018 at 12:44 PM, Steve N4IRS <szingman@...> wrote:
No,
You can use the same port number twice. I try to use the default port numbers where possible. Since you can't use a port twice, you will have to change something. 

On 7/17/2018 1:38 PM, KD5DFB wrote:
Ok, so let me see if I got it correct. So basically all 3 of them use the same port numbers just changing the TX and RX? 

IPSC_Bridge.cfg                     HB_Bridge.cfg                  Analog_Bridge.ini
fromgateway: 31100              fromGateway: 31103         from: 31100
toGateway: 31103                  toGateway: 31100            to: 31103

On Tue, Jul 17, 2018 at 10:00 AM, Steve N4IRS <szingman@...> wrote:


On 7/17/2018 10:51 AM, KD5DFB wrote:
Okay, making progress! I am stumped on the last piece. 

I am trying to figure out the connection between ipsc_bridge and hb_bridge. 

On ipsc_bridge, I have the dmrlink.cfg connecting to the cbridge and can see traffic from the cbridge in the log. Does the ipsc_bridge.cfg connect to hb_bridge.cfg?
Yes

On the hb_bridge I am a little confused. Does the hb_bridge.cfg connect to analog_bridge? Does the ambe need to match what is in analog_bridge?
Just like connecting any of the partners, TX to RX and RX to TX (or words to that effect) Analog_Bridge [AMBE_AUDIO] stanza points to the values in the HB_Bridge [DEFAULTS] stanza.

[AMBE]
EXPORT_IP: 127.0.0.1
EXPORT_PORT: 1234
Ignore these


On Mon, Jul 16, 2018, 21:02 Steve N4IRS <szingman@...> wrote:
I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.
 

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB















Re: C Bridge to P25 Reflector

Michael KD5DFB
 

Okay, let me take a step back and break it down again. 

So, IPSC_Bridge uses both dmrlink.cfg and IPSC_bridge.cfg.  The dmrlink.cfg defines the connection to the cbridge and I see it connected on the control center. IPSC_Bridge.cfg defines the connection to HB_Bridge. Is that defined in the HB_Bridge.cfg or hblink.cfg?

On Tue, Jul 17, 2018 at 12:44 PM, Steve N4IRS <szingman@...> wrote:
No,
You can use the same port number twice. I try to use the default port numbers where possible. Since you can't use a port twice, you will have to change something. 

On 7/17/2018 1:38 PM, KD5DFB wrote:
Ok, so let me see if I got it correct. So basically all 3 of them use the same port numbers just changing the TX and RX? 

IPSC_Bridge.cfg                     HB_Bridge.cfg                  Analog_Bridge.ini
fromgateway: 31100              fromGateway: 31103         from: 31100
toGateway: 31103                  toGateway: 31100            to: 31103

On Tue, Jul 17, 2018 at 10:00 AM, Steve N4IRS <szingman@...> wrote:


On 7/17/2018 10:51 AM, KD5DFB wrote:
Okay, making progress! I am stumped on the last piece. 

I am trying to figure out the connection between ipsc_bridge and hb_bridge. 

On ipsc_bridge, I have the dmrlink.cfg connecting to the cbridge and can see traffic from the cbridge in the log. Does the ipsc_bridge.cfg connect to hb_bridge.cfg?
Yes

On the hb_bridge I am a little confused. Does the hb_bridge.cfg connect to analog_bridge? Does the ambe need to match what is in analog_bridge?
Just like connecting any of the partners, TX to RX and RX to TX (or words to that effect) Analog_Bridge [AMBE_AUDIO] stanza points to the values in the HB_Bridge [DEFAULTS] stanza.

[AMBE]
EXPORT_IP: 127.0.0.1
EXPORT_PORT: 1234
Ignore these


On Mon, Jul 16, 2018, 21:02 Steve N4IRS <szingman@...> wrote:
I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.
 

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB














Re: C Bridge to P25 Reflector

Steve N4IRS
 

No,
You can use the same port number twice. I try to use the default port numbers where possible. Since you can't use a port twice, you will have to change something. 

On 7/17/2018 1:38 PM, KD5DFB wrote:
Ok, so let me see if I got it correct. So basically all 3 of them use the same port numbers just changing the TX and RX? 

IPSC_Bridge.cfg                     HB_Bridge.cfg                  Analog_Bridge.ini
fromgateway: 31100              fromGateway: 31103         from: 31100
toGateway: 31103                  toGateway: 31100            to: 31103

On Tue, Jul 17, 2018 at 10:00 AM, Steve N4IRS <szingman@...> wrote:


On 7/17/2018 10:51 AM, KD5DFB wrote:
Okay, making progress! I am stumped on the last piece. 

I am trying to figure out the connection between ipsc_bridge and hb_bridge. 

On ipsc_bridge, I have the dmrlink.cfg connecting to the cbridge and can see traffic from the cbridge in the log. Does the ipsc_bridge.cfg connect to hb_bridge.cfg?
Yes

On the hb_bridge I am a little confused. Does the hb_bridge.cfg connect to analog_bridge? Does the ambe need to match what is in analog_bridge?
Just like connecting any of the partners, TX to RX and RX to TX (or words to that effect) Analog_Bridge [AMBE_AUDIO] stanza points to the values in the HB_Bridge [DEFAULTS] stanza.

[AMBE]
EXPORT_IP: 127.0.0.1
EXPORT_PORT: 1234
Ignore these


On Mon, Jul 16, 2018, 21:02 Steve N4IRS <szingman@...> wrote:
I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.
 

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB













Re: C Bridge to P25 Reflector

Michael KD5DFB
 

Ok, so let me see if I got it correct. So basically all 3 of them use the same port numbers just changing the TX and RX? 

IPSC_Bridge.cfg                     HB_Bridge.cfg                  Analog_Bridge.ini
fromgateway: 31100              fromGateway: 31103         from: 31100
toGateway: 31103                  toGateway: 31100            to: 31103

On Tue, Jul 17, 2018 at 10:00 AM, Steve N4IRS <szingman@...> wrote:


On 7/17/2018 10:51 AM, KD5DFB wrote:
Okay, making progress! I am stumped on the last piece. 

I am trying to figure out the connection between ipsc_bridge and hb_bridge. 

On ipsc_bridge, I have the dmrlink.cfg connecting to the cbridge and can see traffic from the cbridge in the log. Does the ipsc_bridge.cfg connect to hb_bridge.cfg?
Yes

On the hb_bridge I am a little confused. Does the hb_bridge.cfg connect to analog_bridge? Does the ambe need to match what is in analog_bridge?
Just like connecting any of the partners, TX to RX and RX to TX (or words to that effect) Analog_Bridge [AMBE_AUDIO] stanza points to the values in the HB_Bridge [DEFAULTS] stanza.

[AMBE]
EXPORT_IP: 127.0.0.1
EXPORT_PORT: 1234
Ignore these


On Mon, Jul 16, 2018, 21:02 Steve N4IRS <szingman@...> wrote:
I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.
 

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB












Re: C Bridge to P25 Reflector

Steve N4IRS
 



On 7/17/2018 10:51 AM, KD5DFB wrote:
Okay, making progress! I am stumped on the last piece. 

I am trying to figure out the connection between ipsc_bridge and hb_bridge. 

On ipsc_bridge, I have the dmrlink.cfg connecting to the cbridge and can see traffic from the cbridge in the log. Does the ipsc_bridge.cfg connect to hb_bridge.cfg?
Yes

On the hb_bridge I am a little confused. Does the hb_bridge.cfg connect to analog_bridge? Does the ambe need to match what is in analog_bridge?
Just like connecting any of the partners, TX to RX and RX to TX (or words to that effect) Analog_Bridge [AMBE_AUDIO] stanza points to the values in the HB_Bridge [DEFAULTS] stanza.

[AMBE]
EXPORT_IP: 127.0.0.1
EXPORT_PORT: 1234
Ignore these


On Mon, Jul 16, 2018, 21:02 Steve N4IRS <szingman@...> wrote:
I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.
 

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB











Re: C Bridge to P25 Reflector

Michael KD5DFB
 

Okay, making progress! I am stumped on the last piece. 

I am trying to figure out the connection between ipsc_bridge and hb_bridge. 

On ipsc_bridge, I have the dmrlink.cfg connecting to the cbridge and can see traffic from the cbridge in the log. Does the ipsc_bridge.cfg connect to hb_bridge.cfg? 

On the hb_bridge I am a little confused. Does the hb_bridge.cfg connect to analog_bridge? Does the ambe need to match what is in analog_bridge?

[AMBE]
EXPORT_IP: 127.0.0.1
EXPORT_PORT: 1234


On Mon, Jul 16, 2018, 21:02 Steve N4IRS <szingman@...> wrote:
I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.
 

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB










Re: C Bridge to P25 Reflector

Steve N4IRS
 

I like separate directories at first. Makes it easy to keep things visible. Yes, I uses systemd.
 

On 07/16/2018 09:55 PM, KD5DFB wrote:
Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB










Re: C Bridge to P25 Reflector

Michael KD5DFB
 

Thank you! 

What is your recommendation on running 2 analog bridges? Do I make a new directory and copy the analog_bridge files into it? How can I run 2 at a time? Do I use systemctl? 

On Mon, Jul 16, 2018 at 8:47 PM, Steve N4IRS <szingman@...> wrote:
Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB









Re: C Bridge to P25 Reflector

Steve N4IRS
 

Walk through it one module at a time. You should see the traffic at each step.

On 07/16/2018 09:44 PM, KD5DFB wrote:
Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB








Re: C Bridge to P25 Reflector

Michael KD5DFB
 

Success! Do I need to change anything else under [AMBE_AUDIO] for Analog_bridge_2?


I: 2018-07-17 01:39:11.007 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:12.824 End TX
I: 2018-07-17 01:39:21.690 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:23.327 End TX
I: 2018-07-17 01:39:25.043 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:25.594 End TX
I: 2018-07-17 01:39:39.947 Begin TX: src=3148242 rpt=0 dst=8207 slot=2 cc=0
D: 2018-07-17 01:39:44.125 End TX
 

On Mon, Jul 16, 2018 at 8:20 PM, Steve N4IRS <szingman@...> wrote:
You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB







Re: C Bridge to P25 Reflector

Steve N4IRS
 

You need to make sure the P25 TX and RX ports in DVSwitch.ini point to the proper ports in Analog_Bridge.ini

On 07/16/2018 09:15 PM, KD5DFB wrote:
Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB






Re: C Bridge to P25 Reflector

Michael KD5DFB
 

Okay, trying to take this in small steps and not fry my noodle.

I am working from P25 reflector to c bridge. I have the p25 reflector up and running. I can see my voice traffic on the P25Gateway log and the MMDVM_Bridge log.

Is there anything else I need change in MMDVM_Bridge.ini? I have changed the following:

[General]
Callsign=KD5DFB
Id=314838

[P25]
Enable=1

[P25 Network]
Enable=1

On Analog_Bridge.ini

toASLPort = 32001 
fromASLPort = 34001  

Should I see any traffic if I tail the log or run it ./Analog_Bridge




On Mon, Jul 16, 2018 at 6:57 PM, Steve N4IRS <szingman@...> wrote:
IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB





Re: C Bridge to P25 Reflector

Steve N4IRS
 

IPSC_Bridge and HB_Bridge sub-class dmrlink and hblink. In other words, dmrlink and hblink are the network stack for IPSC_Bridge and HB_Bridge. So you configure hblink.cfg and hblink.cfg.
You will also need to install dmr_utils. Someday I hope IPSC_Bridge and HB_Bridge get merged into the master branches. One could only hope.

Steve N4IRS

On 07/16/2018 07:47 PM, KD5DFB wrote:
Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 


# IPSC_Bridge configuration file #

##################################


# DEFAULTS - General settings. These values are

# inherited in each subsequent section (defined by section value).


[DEFAULTS]

gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)

fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)

toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB




Re: C Bridge to P25 Reflector

Michael KD5DFB
 

Okay, interesting... When I looked at the github under master they are not there. I had to change to branch to IPSC_bridge and HB-Bridge

So, When I look at the IPSC_Bridge.cfg. I only see this. How to I tell it to connect to the cbridge as a peer? 

# IPSC_Bridge configuration file #
##################################
# DEFAULTS - General settings. These values are
# inherited in each subsequent section (defined by section value).
[DEFAULTS]
gateway = 127.0.0.1 # IP address of Partner Application (HB_Bridge, Analog_Bridge)
fromGatewayPort = 31000 # Port IPSC_Bridge is listening on for data (IPSC_Bridge <--- Partner)
toGatewayPort = 31003 # Port Partner is listening on for data (IPSC_Bridge ---> Partner)


On Mon, Jul 16, 2018 at 6:32 PM, Steve N4IRS <szingman@...> wrote:
cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB



Re: C Bridge to P25 Reflector

Steve N4IRS
 

cbridge <-> ipsc_bridge <-> hb_Bridge <-> Analog_Bridge_1 <-> Analog_bridge_2 <-> MMDVM_Bridge <-> P25Gateway <-> P25Reflector

On 07/16/2018 07:29 PM, KD5DFB wrote:
All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB


C Bridge to P25 Reflector

Michael KD5DFB
 

All,

I am trying to setup a bridge between my C Bridge port and my P25 Reflector. When looking at older post I see reference to IPSC_Bridge and HB_bridge. Are those no longer applicable? Do I just use dmrlink and hb_bridge_all ? 

This is what I think it should be...

cbridge <-> dmrlink <-> hblink <-> hb_bridge_all <-> mb1 <-> ab1 <-> ab2 <-> mb2 <-> p25gateway <-> p25reflector

As of right now, I have dmrlink connect to the c bridge and when I tail the log, I can see traffic from dmr. Same on the other side. I have mb2 connectd thru the p25gateway to my p25 reflector. When I tail the log, I can see the p25 traffic. 

Just need some help between the cbridge and mb1 :-)

Michael KD5DFB


Re: YSFn and YSFw

Steve N4IRS
 

9K36F7W

On 07/15/2018 10:42 PM, JJ Cummings wrote:
That’s what they say, but you can’t get a coordination for narrow from anywhere... and Yaesu doesn’t actually publish the emissions info

Sent from the iRoad

On Jul 15, 2018, at 20:32, Steve N4IRS <szingman@...> wrote:

From Yaesu.

V/D Mode (Simultaneous Voice/Data Communication Mode) (Narrow)
Half of the bandwidth is used for voice signal with error correction. The transceiver uses powerful error correction technology developed for professional communication devices. The very effective error correction code provides benefits such as minimal interruption of communication. The basic digital C4FM FDMA mode provides a good balance between sound quality and error correction.

Voice FR Mode (Voice Full Rate Mode) (Wide)
This mode uses the entire 12.5 kHz bandwidth to transmit digital voice data. The larger voice data size allows voice communication with high sound quality. Use this mode for pleasing sound quality communication between amateur radio friends.

On 07/15/2018 10:12 PM, JJ Cummings wrote:
I’d be curious if it’s actually narrowband, I’ve heard repeatedly that it’s not really narrow.

Sent from the iRoad

On Jul 15, 2018, at 20:05, KD5DFB <mhebert1975@...> wrote:

So if I build a YSF reflector, will both modes work with it? My end goal it to connect it to my P25 reflector 

<FDMA_multiple-mode.png>


Re: YSFn and YSFw

JJ Cummings
 

That’s what they say, but you can’t get a coordination for narrow from anywhere... and Yaesu doesn’t actually publish the emissions info

Sent from the iRoad

On Jul 15, 2018, at 20:32, Steve N4IRS <szingman@...> wrote:

From Yaesu.

V/D Mode (Simultaneous Voice/Data Communication Mode) (Narrow)
Half of the bandwidth is used for voice signal with error correction. The transceiver uses powerful error correction technology developed for professional communication devices. The very effective error correction code provides benefits such as minimal interruption of communication. The basic digital C4FM FDMA mode provides a good balance between sound quality and error correction.

Voice FR Mode (Voice Full Rate Mode) (Wide)
This mode uses the entire 12.5 kHz bandwidth to transmit digital voice data. The larger voice data size allows voice communication with high sound quality. Use this mode for pleasing sound quality communication between amateur radio friends.

On 07/15/2018 10:12 PM, JJ Cummings wrote:
I’d be curious if it’s actually narrowband, I’ve heard repeatedly that it’s not really narrow.

Sent from the iRoad

On Jul 15, 2018, at 20:05, KD5DFB <mhebert1975@...> wrote:

So if I build a YSF reflector, will both modes work with it? My end goal it to connect it to my P25 reflector 

<FDMA_multiple-mode.png>

7961 - 7980 of 9800