Hi guys I hope I"m in the right group, I am building a multimode system,  ASL <-----> DMR <-----> YSF <------> P25 <------> DStar, and i will like to use DVSwitch mobile to connect to it, can anyone point me to where i will find information  to achieve this?
I already have ASL linked to DMR and DMR linked YSF working. Do I use HBlink for the XLX connection, and How do I connect to these Using DVswitch Mobile on my phone?


Thanks and Regards
Dexter 9Y4C

Great Job! sorry I forgot to tell you that lol. DMR ID when connecting to XLX should only be your 7 digit DMR ID : )

DISREGARD

Bad metadata. My fault.

Apologies if I'm waking a solved thread, but I seem to be having the same issue. Inbound DStar works on Allstar, but transmitting from Allstar doesn't seem to work.

I: 2020-05-04 21:03:51.186 Analog_Bridge Version 1.4.2 Sun Apr 26 07:18:31 EDT 2020

M: 2020-05-04 20:27:41.246 MMDVM_Bridge-20200309_V1.5.1 is starting
M: 2020-05-04 20:27:41.246 Built 08:23:16 Apr 24 2020 (GitID #59ba047)

I found it.
The reason why it did not work was the DMR ID at the top of the MMDVM_Bridge.ini, It had the two digit Brandmeister addon and that didn´t like the XLX Reflector and refused the connection.
The XLX Reflector was throwing an " unrecognized DMR ID" in the livelog and that gave me the final hint...

Thanks Steve and Eric for helping me out

Uli

Show the DMR Network stanza from MMDVM_Bridge.ini

Hi Eric,
no it does not work, I can see the YSF Reflector connecting to the Bridge but the Bridge does not connect to the XLX Reflector.
I have tried different ports, I can ping the XLX Reflector but MMDVM_Bridge does not connect to it
What I get is this:

E: 2020-05-04 16:56:08.936 DMR, Connection to the master has timed out, retrying connection
M: 2020-05-04 16:56:08.936 DMR, Closing DMR Network
M: 2020-05-04 16:56:08.936 DMR, Opening DMR Network
E: 2020-05-04 16:57:18.947 DMR, Connection to the master has timed out, retrying connection
M: 2020-05-04 16:57:18.947 DMR, Closing DMR Network
M: 2020-05-04 16:57:18.947 DMR, Opening DMR Network
E: 2020-05-04 16:58:28.961 DMR, Connection to the master has timed out, retrying connection
M: 2020-05-04 16:58:28.961 DMR, Closing DMR Network
M: 2020-05-04 16:58:28.962 DMR, Opening DMR Network

I can see traffic coming in to the XLXRef but the Bridge doesn´t see it

Uli

Thanks Eric,
I´ll give it a try

Uli

Uli, 
Just to be clear, this is a YSF Ref <-> XLX Ref modul A

See sample below - this will connect to XLX??? module A

MB.ini

[DMR Network]
Enable=1
Address=ip or DNS of XLX reflector
Port=62030
Jitter=360
Local=62032  >>> pay attention to this port will interfere if duplicate somewhere in the same server.
Password=passw0rd
# for DMR+ see https://github.com/DVSwitch/MMDVM_Bridge/blob/master/DOC/DMRplus_startup_options.md
# for XLX the syntax is: Options=XLX:4009
Options=XLX:4001  >>>>module A
Slot1=0
Slot2=1
Debug=1

[System Fusion Network]
Enable=1
LocalAddress=127.0.0.0
LocalPort=0
GatewayAddress=ip address or DNS of Ref
GatewayPort=42000  >>> YSF port
Debug=1

DVSwitch.ini

[DMR]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 36100                ; Port to send AMBE TLV frames to (export)
RXPort = 36103                  ; Port to listen on (import)
Slot = 2                        ; Export slot

[YSF]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 36103                 ; Port to send AMBE TLV frames to (export)
RXPort = 36100                 ; Port to listen on (import)
FallbackID = your id            ; In case we can not find a valid DMR id in the database, export this one
ExportTG = tg9                 ; Which TG to export 
Slot = 2                        ; Export slot

73, Eric

Thanks.

The update for DVLink V9.2.0 has just been released. It can be updated via OTA or we have provided a link to download images directly from the current version 9.2.0.
Here is a link to download and information as well as CHANGELOG.

http://ea5gvk-dmr.zigor.es/dvlink-v9-change-log/

73 EA5GVK & EA7JCL.

Hi Eric,
here is my MMDVM_Bridge.ini and the DVSwitch.ini
This setup currently bridges a YSF Reflector to a Brandmeister TG (defined in DVSwitch.ini) and works fine
What I have in mind is to replace the existing YSF-only Reflector with the XLX Reflector.
YSF Reflector and Bridge are currently running on 2 separate RPIs
The XLX Reflector runs on another machine, all are in the same network
The XLX Reflector is this one:
https://github.com/n5amd/xlxd-debian-installer
I´m also running AMBED with Vocoder Chip Hardware attached für D-Star

thanks and 73
Uli

******************************MMDVM_Bridge.ini **************************
[General]
Callsign=DJ5UW
Id=263857408
Timeout=180
Duplex=0

[Info]
RXFrequency=222340000
TXFrequency=224940000
Power=1
Latitude=41.7333
Longitude=-50.3999
Height=0
Location=Iceberg, North Atlantic
Description=MMDVM_Bridge
URL=https://groups.io/g/DVSwitch

[Log]
# Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
DisplayLevel=1
FileLevel=2
FilePath=/var/log/mmdvm
FileRoot=MMDVM_Bridge

[DMR Id Lookup]
File=/var/lib/mmdvm/DMRIds.dat
Time=24

[NXDN Id Lookup]
File=/var/lib/mmdvm/NXDN.csv
Time=24

[Modem]
Port=/dev/null
RSSIMappingFile=RSSI.dat
Trace=0
Debug=0

[D-Star]
Enable=0
Module=C

[DMR]
Enable=1
ColorCode=1
EmbeddedLCOnly=1
DumpTAData=0

[System Fusion]
Enable=1

[P25]
Enable=0
NAC=293                                                                                                                
[NXDN]
Enable=0
RAN=1
Id=12345

[D-Star Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=20010
LocalPort=20011
Debug=0

[DMR Network]
Enable=1
Address=master2.bm262.de
Port=62031
Jitter=360
Local=62032
Password=passw0rd
# for DMR+ see https://github.com/DVSwitch/MMDVM_Bridge/blob/master/DOC/DMRplus_startup_options.md
# for XLX the syntax is: Options=XLX:4009
# Options=
Slot1=0
Slot2=1
Debug=1

[System Fusion Network]
Enable=1
LocalAddress=0
LocalPort=3200
GatewayAddress=192.168.10.125
GatewayPort=42004
Debug=1

[P25 Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=42020
LocalPort=32010
Debug=0

[NXDN Network]
Enable=0
#LocalAddress=127.0.0.1
Debug=0
LocalPort=14021
GatewayAddress=127.0.0.1
GatewayPort=14020

***********************************  DVSwitch.ini  ****************************
; MMDVM_Bridge export / import configuration file.
;   This file should be placed along side of MMDVM_Bridge or it can be
;   supplied as a path on the MMDVM_BRIDGE environment variable.

; Configure the Quantar Repeater Partner
; Note that the TX and RX ports are already reversed for MMDVM_Bridge <--> Quantar_Bridge
[QUANTAR]
logFilePath = /var/log/Quantar_Bridge.log
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 34103                  ; Port to send AMBE TLV frames to (export)
RXPort = 34100                  ; Port to listen on (import)
quantarPort = 1994              ; HDLC frames To/From the Quantar repeater
logLevel = 2                    ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error,$debug = 0                       ; Debug 0 = off, 1 = on (adds lots of additional messages)

; Configure the DMR Partner
; Audio format is AMBE 72 bit
[DMR]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 31100                  ; Port to send AMBE TLV frames to (export)
RXPort = 31103                  ; Port to listen on (import)
Slot = 2                        ; Export slot

; Configure the D-Star Partner
; Audio format is AMBE 48 bit (DSAMBE)
[DSTAR]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 32100                  ; Port to send AMBE TLV frames to (export)
RXPort = 32103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
ExportTG = 9                    ; Which TG to export
Slot = 2                        ; Export slot

; Configure the NXDN Partner
; Audio format is AMBE 72 bit
[NXDN]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 33100                  ; Port to send AMBE TLV frames to (export)
RXPort = 33103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, export this one
NXDNFallbackID  = 12345         ; Use this ID when the input DMR ID is not found in the database
Translate = 1234=4321           ; Translate NXDN TG < -- > DMR TG (bidirectional)
Slot = 2                        ; Export slot

; Configure the P25 Partner
; Audio format is IMBE 88 bit
[P25]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 34100                  ; Port to send AMBE TLV frames to (export)
RXPort = 34103                  ; Port to listen on (import)
Slot = 2                        ; Export slot

; Configure the Yaesu Fusion Partner                                                                                   
; Audio format is AMBE 72 bit
; Audio format is IMBE 88 bit
[YSF]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 31103                  ; Port to send AMBE TLV frames to (export)
RXPort = 31100                  ; Port to listen on (import)
FallbackID = 2638574            ; In case we can not find a valid DMR id in the database, export this one
ExportTG = 26283                 ; Which TG to export 
Slot = 2                        ; Export slot

**********************************************************************

Correct.  Is your cbridge ipsc connection a master or client.  I set all my hblink connections as master in cbridge and client in dmrlink.cfg.   Execute IPSC_Bridge and watch the log console.  Make sure UDP ports match on your master IPSC config and dmrlink.cfg Client section.  On the cbridge dont add a password to each IPSC timeslot. Just enable.  

I never played with C-bridge but I believe what your trying accomplish would be something l like this

IPSC_Bridge<->HB_Bridge <->hblink3

Bob

I have a couple of questions that are just causing my mind not to wrap around a few things.
Right now I have IPsec talking to the cbridge and things are flowing in from the cbridge and I see talk groups, Problem I am having is how do I connect HBLink3 to the IPsec? I have tried a few different ways but I get an error saying that HBlink cannot auth with IPsec. I get the following warning
WARNING 2020-05-01 19:47:21,839 (MAIN) AuthError: IPSC packet failed authentication. Type 52: Peer: 1347699532, 127.0.0.1:50002
I am running IPSec_bridge.py and Hblink.py
Also including the config files
Any Help would be great!

Kd2cfh

Very nice deliverable. Earlier comment is right on … "cabin fever" can have some side benefits!!

AGC function makes a big difference. Is there any source you can point me at that describes how to use the AUDIO_BPF option?
--
Tom VE3NY

Uli,
I had my XLX and YSF reflector set up this way one instances of MB and its working. Do you have a copy of your MB.ini that we can take a look?
best and 73, Eric

David,
I have used Button Mapper to determine what code a button sends. <https://play.google.com/store/apps/details?id=flar2.homebutton>

73, Steve N4IRS

I have a 2013 Ford Edge with the SYNC 2 entertainment system.  On Zello I can use the Play/Pause button, on the steering wheel, as my PTT when connected to bluetooth audio.  Setting it up on Zello was easy. All I had to was just press the button I wanted to use as my PTT and it saved it.  It's a little more difficult on DVSwitch.  It wants a numeric code for the PTT.  I have searched for documentation that would tell me which bluetooth buttons sends which numeric codes or an app that would sniff out the numeric codes when the buttons are pressed. I haven't had any luck on either count. Does anyone have ideas how I can find the numeric code, for my steering wheel play/pause button, so that I can use DVSwitch hands free?

Hi Steve
I have tried various settings in the MMDVM_Bridge.ini but it does not work.

The XLX Reflector is the latest from Jan. 2020 which is running the new Wires-X mode (instead of YSF)

Is there a MMDVM_Bridge.ini that contains all necessary entries for this connection?
E.g- the Part that connects to the Brandmeister TG and the part that connects to the XLX Reflector ?
Especially how to connect to Modul A on the reflector and what ports are needed and where exactly to put the IP Adress of the reflector.
The reflector runs on a different machine in the same local net as the bridge 192.168.xx.xx
Are there special entries in the DVSwitch.ini necessary

Uli