Date   

Re: Will Nextion Screen work with dvswitch?

Steve N4IRS
 

John,
I confirmed your finding this morning. We have enabled support for the serial displays including Nextion. Please be aware that you will only see traffic from the native networks, BM, P25 reflector etc. This will be changed as part of the changes for the dashboard.

I have pushed the armhf binary up to github.

73, Steve N4IRS

On 5/23/20 1:47 AM, John K1IF via groups.io wrote:
NO Joy here Steve, will be interesting to see what you find out.


cheers K1IF


Re: Will Nextion Screen work with dvswitch?

John K1IF
 

NO Joy here Steve, will be interesting to see what you find out.


cheers K1IF


Re: Will Nextion Screen work with dvswitch?

Steve N4IRS
 

Then /dev/ttyUSB1 should be your port for the [Nextion] stanza

On 5/21/2020 2:09 PM, John K1IF via groups.io wrote:
sounds good Steve!
Oh I checked on my dvmega cast and i did see a stanza in my dvmega cast that is:
NextionDriver
Port
LogLevel
DataFilesPath
GroupsFile
DMRidFile
removeDim
SleepWhenInactive














Re: Will Nextion Screen work with dvswitch?

John K1IF
 

sounds good Steve!
Oh I checked on my dvmega cast and i did see a stanza in my dvmega cast that is:
NextionDriver
Port
LogLevel
DataFilesPath
GroupsFile
DMRidFile
removeDim
SleepWhenInactive













Re: Will Nextion Screen work with dvswitch?

Steve N4IRS
 

I need to check my display on a working MMDVMHost system first. Once I'm sure the display is good, I'll look into using the display(s) with MMDVM_Bridge. Should know more this weekend.

Steve

On 5/21/2020 1:47 PM, John K1IF via groups.io wrote:
Hello Steve

Unfortunately, the display is not receiving any data from the pi. I am using a 3.5 enhanced (k) version. I am not sure how to load the driver for it. I did try both 2 and 3 for screen layout. I believe I need layout 3 but not sure how to get the driver loaded. Maybe that's why its not working for me? Maybe I can find a tft file for screenlevel 2


Re: Will Nextion Screen work with dvswitch?

John K1IF
 

Hello Steve

Unfortunately, the display is not receiving any data from the pi. I am using a 3.5 enhanced (k) version. I am not sure how to load the driver for it. I did try both 2 and 3 for screen layout. I believe I need layout 3 but not sure how to get the driver loaded. Maybe that's why its not working for me? Maybe I can find a tft file for screenlevel 2


Re: Will Nextion Screen work with dvswitch?

Steve N4IRS
 

As it happens, I was playing with this over the weekend. I have to make sure my display is good.
Changes to MMDVM_Bridge.ini

[General]
Display=Nextion

[Nextion]
Port=/dev/ttyAMA0
Brightness=50
DisplayClock=1
UTC=0
#Screen Layout: 0=G4KLX 2=ON7LDS
ScreenLayout=2
IdleBrightness=20

Set above port to match your system.
Please let me know what you get.
73, Steve N4IRS



On 5/21/2020 9:23 AM, John K1IF via groups.io wrote:
Just wondering if anyone has wired a nextion directly to rpi to get info sent to Nextion screen? If so what files would have to be modified if any?

I'm using rpi with dvsm as a stand alone way to access digi modes (not cross linked to asl (yet)





Thanks K1if John


Will Nextion Screen work with dvswitch?

John K1IF
 

Just wondering if anyone has wired a nextion directly to rpi to get info sent to Nextion screen? If so what files would have to be modified if any?

I'm using rpi with dvsm as a stand alone way to access digi modes (not cross linked to asl (yet)





Thanks K1if John


Re: Possible Loop in QSO DMR and MMDVM_Bridge or Analog_Bridge malfunction.

EA5GVK Joaquin
 

Steve, good afternoon.
We just updated analog_bridge binaries, mmdvm_bridge, also dvswitch.sh and dvswitch.ini and so far so good, we've been almost two days without problems so far.
I will report you any bugs.
Thank you very much for your dedication Steve. Great inspirer of digital radio. A hug.


Re: Updated DVSwitch repository available

francois xavier. humetz <francoisxavier.humetz@...>
 

Bonjour monsieur comment on fait le changement des port et tx port dans le ficher analog bridge.ini je veus mettre le port 46000 et 46001.....merci a vous urgent


Re: #analog_bridge #analog_bridge #analog_bridge

francois xavier. humetz <francoisxavier.humetz@...>
 

bonjour monsieur comment on faire pour changer les port dans le ficher analog bridge.ini..cordialement


Re: new install working but cannot get BM to TGIF to work

Steve N4IRS
 

John,
Happy to hear you got it working.

73, Steve N4IRS

On 5/18/20 5:14 PM, John K1IF via groups.io wrote:
went back over everything and found error in my script. it appears to be working now!! HURRY burn image 

Thanks for pointing me in correct path Steve !

73 John


Re: new install working but cannot get BM to TGIF to work

Tim Porter
 

Don't feel bad John I can't get it working either


On Mon, May 18, 2020, 5:14 PM John K1IF via groups.io <izzy_y2k=yahoo.com@groups.io> wrote:
went back over everything and found error in my script. it appears to be working now!! HURRY burn image 

Thanks for pointing me in correct path Steve !

73 John


Re: new install working but cannot get BM to TGIF to work

John K1IF
 

went back over everything and found error in my script. it appears to be working now!! HURRY burn image 

Thanks for pointing me in correct path Steve !

73 John


Re: new install working but cannot get BM to TGIF to work

John K1IF
 

I changed permissions to 777 on each .sh and now getting...
AB LOG
I: 2020-05-18 20:23:26.901 Tune macro: *14 will invoke "/opt/Analog_Bridge/TGIF_chng.sh"
I: 2020-05-18 20:23:27.263 rxport=: 30000
M: 2020-05-18 20:23:27.264 TLV rx socket reopened for 127.0.0.1:30000
I: 2020-05-18 20:23:28.549 MESSAGE packet sent to USRP client: Setting mode to DMR
I: 2020-05-18 20:23:28.621 ambeMode = DMR, size = 72
M: 2020-05-18 20:23:28.621 Connecting to DV3000 hardware......
M: 2020-05-18 20:23:28.633 Begin DV3000 decode
M: 2020-05-18 20:23:28.633 DV3000 latency is currently set to 1
I: 2020-05-18 20:23:28.688 txport=: 31103
I: 2020-05-18 20:23:28.759 rxport=: 31100
E: 2020-05-18 20:23:28.759 Can not bind port 31100, error code = 98 (Address already in use)
M: 2020-05-18 20:23:28.759 TLV rx socket reopened for 127.0.0.1:31100
I: 2020-05-18 20:23:31.383 Macro result was 0
I: 2020-05-18 20:24:15.123 txTg=: 4000
M: 2020-05-18 20:24:53.782 TLV tx socket re-opened for 127.0.0.1:415496
M: 2020-05-18 20:24:53.782 PTT on
M: 2020-05-18 20:24:56.197 Short transmission, extend hang time by 85 ms
M: 2020-05-18 20:24:56.317 PTT off (keyed for 2535 ms)
from command line:
cp:  missing destination file operand after /opt/MMDVM_Bridge/MMDVM_Bridge_TGIF.ini/optMMDVM_Bridge/MMDVM_Bridge.ini


Re: new install working but cannot get BM to TGIF to work

John K1IF
 

permission denied when ran from #


Re: DVSwitch Dashboard

Tom Corcoran
 

Hello Jason,

I'm doing something major wrong … my dashboard only shows Dstar Network as "green". All others are red or blank even though I have all modes enables. Hmmm.


--
Tom VE3NY


Re: new install working but cannot get BM to TGIF to work

Steve N4IRS
 

What happens when you run /opt/Analog_Bridge/BM_chng.sh from the command line?

On 5/18/20 3:49 PM, John K1IF via groups.io wrote:
Steve, Thank you for the quick reply..
I changed the dvsm.macro to :
13 = /opt/Analog_Bridge/BM_chng.sh
14 = /opt/Analog_Bridge/TGIF_chng.sh

It is still on Brandmeister network
here is the AB log now:

I: 2020-05-18 19:38:58.192 Tune macro: *14 will invoke "/opt/Analog_Bridge/TGIF_chng.sh"
I: 2020-05-18 19:38:58.203 Macro result was 32256
I: 2020-05-18 19:39:20.066 USRP reset server IP address to 169.254.42.42:46001
I: 2020-05-18 19:39:20.066 USRP unregister client
I: 2020-05-18 19:39:22.420 USRP server ip change from 169.254.42.42 to new ip:port 192.168.1.7:46001
I: 2020-05-18 19:39:23.404 INFO packet sent to USRP client
I: 2020-05-18 19:39:23.404 codec=slin
I: 2020-05-18 19:39:23.743 USRP packet type: USRP_TYPE_TEXT (K1IF) -> 3100128
I: 2020-05-18 19:39:23.743 USRP packet type: USRP_TYPE_TEXT (K1IF) -> 3100128
I: 2020-05-18 19:41:18.582 txTg=: 4000
I: 2020-05-18 19:41:21.943 Begin TX: src=4000 rpt=0 dst=3100128 slot=2 cc=128 call=4000
I: 2020-05-18 19:41:32.159 txTg=: 91
I: 2020-05-18 19:41:32.589 Begin TX: src=3020845 rpt=0 dst=91 slot=2 cc=0 call=VE3RIA
I: 2020-05-18 19:42:03.855 Begin TX: src=3142386 rpt=0 dst=91 slot=2 cc=0 call=KC3PEX
I: 2020-05-18 19:42:14.050 txTg=: 4000
I: 2020-05-18 19:42:17.441 Begin TX: src=4000 rpt=0 dst=3100128 slot=2 cc=128 call=4000


Thanks


Re: new install working but cannot get BM to TGIF to work

John K1IF
 

Steve, Thank you for the quick reply..
I changed the dvsm.macro to :
13 = /opt/Analog_Bridge/BM_chng.sh
14 = /opt/Analog_Bridge/TGIF_chng.sh

It is still on Brandmeister network
here is the AB log now:

I: 2020-05-18 19:38:58.192 Tune macro: *14 will invoke "/opt/Analog_Bridge/TGIF_chng.sh"
I: 2020-05-18 19:38:58.203 Macro result was 32256
I: 2020-05-18 19:39:20.066 USRP reset server IP address to 169.254.42.42:46001
I: 2020-05-18 19:39:20.066 USRP unregister client
I: 2020-05-18 19:39:22.420 USRP server ip change from 169.254.42.42 to new ip:port 192.168.1.7:46001
I: 2020-05-18 19:39:23.404 INFO packet sent to USRP client
I: 2020-05-18 19:39:23.404 codec=slin
I: 2020-05-18 19:39:23.743 USRP packet type: USRP_TYPE_TEXT (K1IF) -> 3100128
I: 2020-05-18 19:39:23.743 USRP packet type: USRP_TYPE_TEXT (K1IF) -> 3100128
I: 2020-05-18 19:41:18.582 txTg=: 4000
I: 2020-05-18 19:41:21.943 Begin TX: src=4000 rpt=0 dst=3100128 slot=2 cc=128 call=4000
I: 2020-05-18 19:41:32.159 txTg=: 91
I: 2020-05-18 19:41:32.589 Begin TX: src=3020845 rpt=0 dst=91 slot=2 cc=0 call=VE3RIA
I: 2020-05-18 19:42:03.855 Begin TX: src=3142386 rpt=0 dst=91 slot=2 cc=0 call=KC3PEX
I: 2020-05-18 19:42:14.050 txTg=: 4000
I: 2020-05-18 19:42:17.441 Begin TX: src=4000 rpt=0 dst=3100128 slot=2 cc=128 call=4000


Thanks


Re: new install working but cannot get BM to TGIF to work

Steve N4IRS
 

John,
Below you said you created the .sh files in the AB directory. But your macros are trying to run them out of the MB directory.
See below.

On 5/18/20 3:06 PM, John K1IF via groups.io wrote:
Ive created the additional .ini files in MB directory:
MMDVM_Bridge_TGIF
MMDVM_Bridge_BM

i then created the .sh files in AB directory:
TGIF_chng.sh
BM_chng.sh

I also edited the file dvsm.macro and added:
13 = /opt/MMDVM_Bridge/BM_chng.sh
14 = /opt/MMDVM_Bridge/TGIF_chng.sh

i read that dvsm.ini has to be edited but there isn't a file that I can find named that

I keep getting this in the AB log...
I: 2020-05-18 18:46:07.074 Tune macro: *14 will invoke "/opt/MMDVM_Bridge/TGIF_chng.sh"
I: 2020-05-18 18:46:07.080 Macro result was 32256

been reading all the messages but still cannot figure out after several hours :(

please help

3101 - 3120 of 9528