Date   

Re: P25<-->DMR issue "Still"

Ian Tulley
 

OK, nothing using that port, results of unane -a,
Linux dvswitch 4.9.0-3-amd64 #1 SMP Debian 4.9.30-2+deb9u1 (2017-06-18) x86_64 GNU/Linux

and now it is working fine with the md380-emu running and useEmulator = true, so I’m not sure what went wrong there Steve, but thanks for that help, I will need to do another one of these in the near future so I have noted all that has been done so I can see if it works or has the same issues. At least I know now what I will have to do.

Regards
Ian (VK2HK)





On 3 Jan 2019, at 12:31 pm, Steve N4IRS <szingman@...> wrote:

Well,
That looks fine but you did report timeouts with the Emulator before. Maybe something else is listening to UDP 2470 (I doubt it)
Stop the emulator
netstat -unap | grep 2470

You can also get the leves set then retry the emulator.

what is the result of uname -a?

Steve

On 1/2/19 8:27 PM, Ian Tulley wrote:
Thanks Steve, OK, I think I have the audio level adjusted now, It may need some tweaking as I go along but it seems even between both P25 and DMR.

Her is a copy of the systemclt status for the md380-emu

root@dvswitch:/opt/MMDVM_Bridge# systemctl status md380-emu
● md380-emu.service - MD-380 Emulator Service
   Loaded: loaded (/lib/systemd/system/md380-emu.service; enabled; vendor preset: enabled)
   Active: active (running) since Thu 2019-01-03 08:50:49 AEDT; 3h 34min ago
 Main PID: 28048 (md380-emu)
    Tasks: 2 (limit: 4915)
   CGroup: /system.slice/md380-emu.service
           └─28048 /usr/bin/qemu-arm-static /opt/md380-emu/md380-emu -S 2470

It appears that it is running correctly and I have restarted it a few times over all my original testing.

Regards
Ian (VK2HK)





On 3 Jan 2019, at 12:01 pm, Steve N4IRS <szingman@...> wrote:

Go ahead and adjust your levels. md380-emu is having a problem. We can circle back a see waht is going on with the emulator.

On 1/2/19 8:00 PM, Ian Tulley wrote:
That worked Steve, thanks, other than very low Audio from P25 to DMR, using the settings both as 1.0 it is now working fine, so I will need to adjust those settings to get it going correctly. I didn’t think of that for the DMR side ??


Regards
Ian (VK2HK)





On 3 Jan 2019, at 11:44 am, Ian Tulley <ian@...> wrote:

Hi Steve, wasn’t sure if you wanted it as an attachment, hoping it works via the group.




Regards
Ian (VK2HK)





On 3 Jan 2019, at 10:08 am, Ian Tulley <ian@...> wrote:

OK, still having issues on the audio side, no matter the combination of the Audio Gain etc, it does make some differences but from P25 to DMR you can make out some of the audio but very very broken up, but from DMR to P25 its just garbage.

When I run the Analog_Bridge_P25.ini and TX, this is the last entries I see on the screen so this shows both from DMR to P25 and visa versa.

I: 2019-01-02 22:58:32.106 Open UDP listener on 127.0.0.1:34100
I: 2019-01-02 22:58:32.106 Open USRP on 127.0.0.1:32001
M: 2019-01-02 22:58:32.106 Connecting to DV3000 hardware......
W: 2019-01-02 22:58:33.115 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 22:58:33.214 Subscriber IDs loaded: 117848
I: 2019-01-02 22:58:33.215 Default extended metadata <VK2HK>
W: 2019-01-02 22:58:33.215 Using software MBE decoder version 1.2.3
W: 2019-01-02 22:58:33.215 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 22:58:33.215 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 22:58:33.215 Open UDP listener on 127.0.0.1:34001
I: 2019-01-02 22:58:33.215 Starting USRP --> IPSC_Bridge thread
I: 2019-01-02 23:02:56.562 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:02:57.062 PTT on
M: 2019-01-02 23:02:59.907 PTT off (keyed for 2845 ms)
I: 2019-01-02 23:03:13.110 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0


This is the same but from the Analog_Bridge_DMR.ini

I: 2019-01-02 23:02:38.868 Open UDP listener on 127.0.0.1:31100
I: 2019-01-02 23:02:38.868 Open USRP on 127.0.0.1:34001
D: 2019-01-02 23:02:38.868 Attempt to  init DV3000 in DMR mode
M: 2019-01-02 23:02:38.868 Connecting to DV3000 hardware......
W: 2019-01-02 23:02:39.881 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 23:02:39.986 Subscriber IDs loaded: 117848
I: 2019-01-02 23:02:39.987 Default extended metadata <50521891>
I: 2019-01-02 23:02:39.987 Connecting to emulator on host 127.0.0.1:2470
W: 2019-01-02 23:02:39.987 Using software MBE decoder version 1.2.3
W: 2019-01-02 23:02:39.987 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 23:02:39.987 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 23:02:39.987 Open UDP listener on 127.0.0.1:32001
I: 2019-01-02 23:02:39.987 Starting USRP --> HB_Bridge thread
I: 2019-01-02 23:02:56.562 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0
D: 2019-01-02 23:02:59.907 End TX
I: 2019-01-02 23:03:13.111 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:03:13.613 PTT on
D: 2019-01-02 23:03:18.694 cpu_time_used = 5081, minTxTime = 2000, pttTime = 1546470193613, end = 1546470198694
M: 2019-01-02 23:03:18.694 PTT off (keyed for 5081 ms)


Just making sure that it looks as it should to you

Regards
Ian (VK2HK)





On 3 Jan 2019, at 7:51 am, Steve N4IRS <szingman@...> wrote:

Set the USRP audio settings in BOTH ini files to:
aslAudio = AUDIO_USE_GAIN
agcGain = 1.0
dmrAudio = AUDIO_USE_GAIN
dmrGain = 1.0

From there you can go up to 1.5,2,etc or down .9,.8,etc.


On 1/2/2019 3:46 PM, Ian Tulley wrote:
Hi Steve, if I do systemctl status md380-emu it shows it as running, if I TX from the P25 radio, I get very broken audio out of the DMR, if I TX from the DMR Radio I just get very harsh hash from the P25 Radio, that was with the USRP Audio settings as per default. I am assuming I will need to adjust those on both of the Analog_Bridge ini files ??

I have not done any as yet this morning, but will be looking at it hopefully in the next hour.

------------------
Regards
Ian (VK2HK)




On 2 Jan 2019, at 9:36 pm, Steve N4IRS <szingman@...> wrote:

So,
it sounds like P25 is working all the way to Analog_Bridge. It also sounds like you have a problem with Analog_Bridge for DMR. 
Are you using the emulator?
Is the emulator running?

Steve

On 1/2/19 2:40 AM, Ian Tulley wrote:
Hi Steve, OK here is what I have been able to achieve, P25Gateway runs fine, I can then start MMDVM_Bridge and it connects to the BM Master successfully, I can TX on both the P25 radio and the DMR radio on different repeaters and see my calls come up on the screen output. I then start up Analog_Bridge_P25.ini and do the same test and again can see myself coming up on the screen output but no audio between them. Now when I startup Analog_Bridge_DMR.ini and do the same test I can see myself come up on the screen output then I get the following error, only on that Stanza, "Emulator Timed out on Decode" or "Emulator Timed out on Encode" depending on the direction of the data and still no audio in either direction, but I can get the DMR repeater to TX "sometimes" when PTT from the P25 radio but no audio.
I'm not sure where to look for this one, please remember this is on a server in the cloud so there are no USB Dongles connected, I'm only using the software decoder.

Regards
Ian (VK2HK) 





<Analog_Bridge_DMR.ini>






Re: P25<-->DMR issue "Still"

Steve N4IRS
 

Well,
That looks fine but you did report timeouts with the Emulator before. Maybe something else is listening to UDP 2470 (I doubt it)
Stop the emulator
netstat -unap | grep 2470

You can also get the leves set then retry the emulator.

what is the result of uname -a?

Steve

On 1/2/19 8:27 PM, Ian Tulley wrote:
Thanks Steve, OK, I think I have the audio level adjusted now, It may need some tweaking as I go along but it seems even between both P25 and DMR.

Her is a copy of the systemclt status for the md380-emu

root@dvswitch:/opt/MMDVM_Bridge# systemctl status md380-emu
● md380-emu.service - MD-380 Emulator Service
   Loaded: loaded (/lib/systemd/system/md380-emu.service; enabled; vendor preset: enabled)
   Active: active (running) since Thu 2019-01-03 08:50:49 AEDT; 3h 34min ago
 Main PID: 28048 (md380-emu)
    Tasks: 2 (limit: 4915)
   CGroup: /system.slice/md380-emu.service
           └─28048 /usr/bin/qemu-arm-static /opt/md380-emu/md380-emu -S 2470

It appears that it is running correctly and I have restarted it a few times over all my original testing.

Regards
Ian (VK2HK)





On 3 Jan 2019, at 12:01 pm, Steve N4IRS <szingman@...> wrote:

Go ahead and adjust your levels. md380-emu is having a problem. We can circle back a see waht is going on with the emulator.

On 1/2/19 8:00 PM, Ian Tulley wrote:
That worked Steve, thanks, other than very low Audio from P25 to DMR, using the settings both as 1.0 it is now working fine, so I will need to adjust those settings to get it going correctly. I didn’t think of that for the DMR side ??


Regards
Ian (VK2HK)





On 3 Jan 2019, at 11:44 am, Ian Tulley <ian@...> wrote:

Hi Steve, wasn’t sure if you wanted it as an attachment, hoping it works via the group.




Regards
Ian (VK2HK)





On 3 Jan 2019, at 10:08 am, Ian Tulley <ian@...> wrote:

OK, still having issues on the audio side, no matter the combination of the Audio Gain etc, it does make some differences but from P25 to DMR you can make out some of the audio but very very broken up, but from DMR to P25 its just garbage.

When I run the Analog_Bridge_P25.ini and TX, this is the last entries I see on the screen so this shows both from DMR to P25 and visa versa.

I: 2019-01-02 22:58:32.106 Open UDP listener on 127.0.0.1:34100
I: 2019-01-02 22:58:32.106 Open USRP on 127.0.0.1:32001
M: 2019-01-02 22:58:32.106 Connecting to DV3000 hardware......
W: 2019-01-02 22:58:33.115 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 22:58:33.214 Subscriber IDs loaded: 117848
I: 2019-01-02 22:58:33.215 Default extended metadata <VK2HK>
W: 2019-01-02 22:58:33.215 Using software MBE decoder version 1.2.3
W: 2019-01-02 22:58:33.215 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 22:58:33.215 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 22:58:33.215 Open UDP listener on 127.0.0.1:34001
I: 2019-01-02 22:58:33.215 Starting USRP --> IPSC_Bridge thread
I: 2019-01-02 23:02:56.562 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:02:57.062 PTT on
M: 2019-01-02 23:02:59.907 PTT off (keyed for 2845 ms)
I: 2019-01-02 23:03:13.110 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0


This is the same but from the Analog_Bridge_DMR.ini

I: 2019-01-02 23:02:38.868 Open UDP listener on 127.0.0.1:31100
I: 2019-01-02 23:02:38.868 Open USRP on 127.0.0.1:34001
D: 2019-01-02 23:02:38.868 Attempt to  init DV3000 in DMR mode
M: 2019-01-02 23:02:38.868 Connecting to DV3000 hardware......
W: 2019-01-02 23:02:39.881 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 23:02:39.986 Subscriber IDs loaded: 117848
I: 2019-01-02 23:02:39.987 Default extended metadata <50521891>
I: 2019-01-02 23:02:39.987 Connecting to emulator on host 127.0.0.1:2470
W: 2019-01-02 23:02:39.987 Using software MBE decoder version 1.2.3
W: 2019-01-02 23:02:39.987 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 23:02:39.987 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 23:02:39.987 Open UDP listener on 127.0.0.1:32001
I: 2019-01-02 23:02:39.987 Starting USRP --> HB_Bridge thread
I: 2019-01-02 23:02:56.562 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0
D: 2019-01-02 23:02:59.907 End TX
I: 2019-01-02 23:03:13.111 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:03:13.613 PTT on
D: 2019-01-02 23:03:18.694 cpu_time_used = 5081, minTxTime = 2000, pttTime = 1546470193613, end = 1546470198694
M: 2019-01-02 23:03:18.694 PTT off (keyed for 5081 ms)


Just making sure that it looks as it should to you

Regards
Ian (VK2HK)





On 3 Jan 2019, at 7:51 am, Steve N4IRS <szingman@...> wrote:

Set the USRP audio settings in BOTH ini files to:
aslAudio = AUDIO_USE_GAIN
agcGain = 1.0
dmrAudio = AUDIO_USE_GAIN
dmrGain = 1.0

From there you can go up to 1.5,2,etc or down .9,.8,etc.


On 1/2/2019 3:46 PM, Ian Tulley wrote:
Hi Steve, if I do systemctl status md380-emu it shows it as running, if I TX from the P25 radio, I get very broken audio out of the DMR, if I TX from the DMR Radio I just get very harsh hash from the P25 Radio, that was with the USRP Audio settings as per default. I am assuming I will need to adjust those on both of the Analog_Bridge ini files ??

I have not done any as yet this morning, but will be looking at it hopefully in the next hour.

------------------
Regards
Ian (VK2HK)




On 2 Jan 2019, at 9:36 pm, Steve N4IRS <szingman@...> wrote:

So,
it sounds like P25 is working all the way to Analog_Bridge. It also sounds like you have a problem with Analog_Bridge for DMR. 
Are you using the emulator?
Is the emulator running?

Steve

On 1/2/19 2:40 AM, Ian Tulley wrote:
Hi Steve, OK here is what I have been able to achieve, P25Gateway runs fine, I can then start MMDVM_Bridge and it connects to the BM Master successfully, I can TX on both the P25 radio and the DMR radio on different repeaters and see my calls come up on the screen output. I then start up Analog_Bridge_P25.ini and do the same test and again can see myself coming up on the screen output but no audio between them. Now when I startup Analog_Bridge_DMR.ini and do the same test I can see myself come up on the screen output then I get the following error, only on that Stanza, "Emulator Timed out on Decode" or "Emulator Timed out on Encode" depending on the direction of the data and still no audio in either direction, but I can get the DMR repeater to TX "sometimes" when PTT from the P25 radio but no audio.
I'm not sure where to look for this one, please remember this is on a server in the cloud so there are no USB Dongles connected, I'm only using the software decoder.

Regards
Ian (VK2HK) 





<Analog_Bridge_DMR.ini>





Re: P25<-->DMR issue "Still"

Ian Tulley
 

Thanks Steve, OK, I think I have the audio level adjusted now, It may need some tweaking as I go along but it seems even between both P25 and DMR.

Her is a copy of the systemclt status for the md380-emu

root@dvswitch:/opt/MMDVM_Bridge# systemctl status md380-emu
● md380-emu.service - MD-380 Emulator Service
   Loaded: loaded (/lib/systemd/system/md380-emu.service; enabled; vendor preset: enabled)
   Active: active (running) since Thu 2019-01-03 08:50:49 AEDT; 3h 34min ago
 Main PID: 28048 (md380-emu)
    Tasks: 2 (limit: 4915)
   CGroup: /system.slice/md380-emu.service
           └─28048 /usr/bin/qemu-arm-static /opt/md380-emu/md380-emu -S 2470

It appears that it is running correctly and I have restarted it a few times over all my original testing.

Regards
Ian (VK2HK)





On 3 Jan 2019, at 12:01 pm, Steve N4IRS <szingman@...> wrote:

Go ahead and adjust your levels. md380-emu is having a problem. We can circle back a see waht is going on with the emulator.

On 1/2/19 8:00 PM, Ian Tulley wrote:
That worked Steve, thanks, other than very low Audio from P25 to DMR, using the settings both as 1.0 it is now working fine, so I will need to adjust those settings to get it going correctly. I didn’t think of that for the DMR side ??


Regards
Ian (VK2HK)





On 3 Jan 2019, at 11:44 am, Ian Tulley <ian@...> wrote:

Hi Steve, wasn’t sure if you wanted it as an attachment, hoping it works via the group.




Regards
Ian (VK2HK)





On 3 Jan 2019, at 10:08 am, Ian Tulley <ian@...> wrote:

OK, still having issues on the audio side, no matter the combination of the Audio Gain etc, it does make some differences but from P25 to DMR you can make out some of the audio but very very broken up, but from DMR to P25 its just garbage.

When I run the Analog_Bridge_P25.ini and TX, this is the last entries I see on the screen so this shows both from DMR to P25 and visa versa.

I: 2019-01-02 22:58:32.106 Open UDP listener on 127.0.0.1:34100
I: 2019-01-02 22:58:32.106 Open USRP on 127.0.0.1:32001
M: 2019-01-02 22:58:32.106 Connecting to DV3000 hardware......
W: 2019-01-02 22:58:33.115 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 22:58:33.214 Subscriber IDs loaded: 117848
I: 2019-01-02 22:58:33.215 Default extended metadata <VK2HK>
W: 2019-01-02 22:58:33.215 Using software MBE decoder version 1.2.3
W: 2019-01-02 22:58:33.215 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 22:58:33.215 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 22:58:33.215 Open UDP listener on 127.0.0.1:34001
I: 2019-01-02 22:58:33.215 Starting USRP --> IPSC_Bridge thread
I: 2019-01-02 23:02:56.562 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:02:57.062 PTT on
M: 2019-01-02 23:02:59.907 PTT off (keyed for 2845 ms)
I: 2019-01-02 23:03:13.110 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0


This is the same but from the Analog_Bridge_DMR.ini

I: 2019-01-02 23:02:38.868 Open UDP listener on 127.0.0.1:31100
I: 2019-01-02 23:02:38.868 Open USRP on 127.0.0.1:34001
D: 2019-01-02 23:02:38.868 Attempt to  init DV3000 in DMR mode
M: 2019-01-02 23:02:38.868 Connecting to DV3000 hardware......
W: 2019-01-02 23:02:39.881 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 23:02:39.986 Subscriber IDs loaded: 117848
I: 2019-01-02 23:02:39.987 Default extended metadata <50521891>
I: 2019-01-02 23:02:39.987 Connecting to emulator on host 127.0.0.1:2470
W: 2019-01-02 23:02:39.987 Using software MBE decoder version 1.2.3
W: 2019-01-02 23:02:39.987 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 23:02:39.987 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 23:02:39.987 Open UDP listener on 127.0.0.1:32001
I: 2019-01-02 23:02:39.987 Starting USRP --> HB_Bridge thread
I: 2019-01-02 23:02:56.562 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0
D: 2019-01-02 23:02:59.907 End TX
I: 2019-01-02 23:03:13.111 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:03:13.613 PTT on
D: 2019-01-02 23:03:18.694 cpu_time_used = 5081, minTxTime = 2000, pttTime = 1546470193613, end = 1546470198694
M: 2019-01-02 23:03:18.694 PTT off (keyed for 5081 ms)


Just making sure that it looks as it should to you

Regards
Ian (VK2HK)





On 3 Jan 2019, at 7:51 am, Steve N4IRS <szingman@...> wrote:

Set the USRP audio settings in BOTH ini files to:
aslAudio = AUDIO_USE_GAIN
agcGain = 1.0
dmrAudio = AUDIO_USE_GAIN
dmrGain = 1.0

From there you can go up to 1.5,2,etc or down .9,.8,etc.


On 1/2/2019 3:46 PM, Ian Tulley wrote:
Hi Steve, if I do systemctl status md380-emu it shows it as running, if I TX from the P25 radio, I get very broken audio out of the DMR, if I TX from the DMR Radio I just get very harsh hash from the P25 Radio, that was with the USRP Audio settings as per default. I am assuming I will need to adjust those on both of the Analog_Bridge ini files ??

I have not done any as yet this morning, but will be looking at it hopefully in the next hour.

------------------
Regards
Ian (VK2HK)




On 2 Jan 2019, at 9:36 pm, Steve N4IRS <szingman@...> wrote:

So,
it sounds like P25 is working all the way to Analog_Bridge. It also sounds like you have a problem with Analog_Bridge for DMR. 
Are you using the emulator?
Is the emulator running?

Steve

On 1/2/19 2:40 AM, Ian Tulley wrote:
Hi Steve, OK here is what I have been able to achieve, P25Gateway runs fine, I can then start MMDVM_Bridge and it connects to the BM Master successfully, I can TX on both the P25 radio and the DMR radio on different repeaters and see my calls come up on the screen output. I then start up Analog_Bridge_P25.ini and do the same test and again can see myself coming up on the screen output but no audio between them. Now when I startup Analog_Bridge_DMR.ini and do the same test I can see myself come up on the screen output then I get the following error, only on that Stanza, "Emulator Timed out on Decode" or "Emulator Timed out on Encode" depending on the direction of the data and still no audio in either direction, but I can get the DMR repeater to TX "sometimes" when PTT from the P25 radio but no audio.
I'm not sure where to look for this one, please remember this is on a server in the cloud so there are no USB Dongles connected, I'm only using the software decoder.

Regards
Ian (VK2HK) 





<Analog_Bridge_DMR.ini>




Re: Interface ASL into existing bridge

Michael KD5DFB
 

So many options! I like that way too...

On Wed, Jan 2, 2019 at 7:15 PM Steve N4IRS <szingman@...> wrote:
One way you could do it is use ASL as your "mixer" Break the chain at the junction of the 2 Analog_Bridges. ASL with 2 private nodes. One connected to P25 and one connected to DMR. Then connect the 2 private nodes together and connect your public ASL node to one of the private nodes.

On 1/2/19 8:09 PM, KD5DFB wrote:
I have a c-bridge to p25 reflector bridge

cbridge<-->IPSC_Bridge<-->Analog_Bridge_DMR<-->Analog_Bridge_P25<-->MMDVM_Bridge<-->P25Gateway<-->P25Reflector  

On Wed, Jan 2, 2019 at 7:07 PM JJ Cummings <cummingsj@...> wrote:
Much much more info is needed, that said the answer is likely YES that you can interface ASL into existing bridges for other modes also.... but each has its own complexities and there is no single answer to interface ASL into an existing ambiguous bridge ;-P

On Wed, Jan 2, 2019 at 6:04 PM Mike KB8JNM <groupio@...> wrote:

Would you like to say what kind of bridge ?

Or

Exactly what you are trying to achieve ?

...mike/kb8jnm


On 1/2/2019 6:29 PM, KD5DFB wrote:
Hello, Group,

Is there a way to interface ASL into an existing bridge?

Michael KD5DFB


Re: Interface ASL into existing bridge

Michael KD5DFB
 

Awesome, Thank you! I just couldn't see it. 

Now if I could figure out how to limit the TS and TGs that go to P25

On Wed, Jan 2, 2019 at 7:14 PM JJ Cummings <cummingsj@...> wrote:
ha!

So given what I'm looking at you could interface another MMDVM_Bridge into the P25Gateway and then Analog_Bridge using USRP into ASL from MMDVM_Bridge... 

So the chain from your existing P25Gateway <-> NewMMDVM_Bridge <-> Analog_Bridge <-> USRP ASL

You could do the same on the CBridge side with DMRLink...

On Wed, Jan 2, 2019 at 6:10 PM Steve N4IRS <szingman@...> wrote:
The bridge formerly known as Prince? Sorry a little punchy tonight.

On 1/2/19 8:07 PM, JJ Cummings wrote:
Much much more info is needed, that said the answer is likely YES that you can interface ASL into existing bridges for other modes also.... but each has its own complexities and there is no single answer to interface ASL into an existing ambiguous bridge ;-P

On Wed, Jan 2, 2019 at 6:04 PM Mike KB8JNM <groupio@...> wrote:

Would you like to say what kind of bridge ?

Or

Exactly what you are trying to achieve ?

...mike/kb8jnm


On 1/2/2019 6:29 PM, KD5DFB wrote:
Hello, Group,

Is there a way to interface ASL into an existing bridge?

Michael KD5DFB


Re: Interface ASL into existing bridge

Steve N4IRS
 

One way you could do it is use ASL as your "mixer" Break the chain at the junction of the 2 Analog_Bridges. ASL with 2 private nodes. One connected to P25 and one connected to DMR. Then connect the 2 private nodes together and connect your public ASL node to one of the private nodes.

On 1/2/19 8:09 PM, KD5DFB wrote:
I have a c-bridge to p25 reflector bridge

cbridge<-->IPSC_Bridge<-->Analog_Bridge_DMR<-->Analog_Bridge_P25<-->MMDVM_Bridge<-->P25Gateway<-->P25Reflector  

On Wed, Jan 2, 2019 at 7:07 PM JJ Cummings <cummingsj@...> wrote:
Much much more info is needed, that said the answer is likely YES that you can interface ASL into existing bridges for other modes also.... but each has its own complexities and there is no single answer to interface ASL into an existing ambiguous bridge ;-P

On Wed, Jan 2, 2019 at 6:04 PM Mike KB8JNM <groupio@...> wrote:

Would you like to say what kind of bridge ?

Or

Exactly what you are trying to achieve ?

...mike/kb8jnm


On 1/2/2019 6:29 PM, KD5DFB wrote:
Hello, Group,

Is there a way to interface ASL into an existing bridge?

Michael KD5DFB


Re: Interface ASL into existing bridge

JJ Cummings
 

ha!

So given what I'm looking at you could interface another MMDVM_Bridge into the P25Gateway and then Analog_Bridge using USRP into ASL from MMDVM_Bridge... 

So the chain from your existing P25Gateway <-> NewMMDVM_Bridge <-> Analog_Bridge <-> USRP ASL

You could do the same on the CBridge side with DMRLink...

On Wed, Jan 2, 2019 at 6:10 PM Steve N4IRS <szingman@...> wrote:
The bridge formerly known as Prince? Sorry a little punchy tonight.

On 1/2/19 8:07 PM, JJ Cummings wrote:
Much much more info is needed, that said the answer is likely YES that you can interface ASL into existing bridges for other modes also.... but each has its own complexities and there is no single answer to interface ASL into an existing ambiguous bridge ;-P

On Wed, Jan 2, 2019 at 6:04 PM Mike KB8JNM <groupio@...> wrote:

Would you like to say what kind of bridge ?

Or

Exactly what you are trying to achieve ?

...mike/kb8jnm


On 1/2/2019 6:29 PM, KD5DFB wrote:
Hello, Group,

Is there a way to interface ASL into an existing bridge?

Michael KD5DFB


Re: Interface ASL into existing bridge

Steve N4IRS
 

The bridge formerly known as Prince? Sorry a little punchy tonight.

On 1/2/19 8:07 PM, JJ Cummings wrote:
Much much more info is needed, that said the answer is likely YES that you can interface ASL into existing bridges for other modes also.... but each has its own complexities and there is no single answer to interface ASL into an existing ambiguous bridge ;-P

On Wed, Jan 2, 2019 at 6:04 PM Mike KB8JNM <groupio@...> wrote:

Would you like to say what kind of bridge ?

Or

Exactly what you are trying to achieve ?

...mike/kb8jnm


On 1/2/2019 6:29 PM, KD5DFB wrote:
Hello, Group,

Is there a way to interface ASL into an existing bridge?

Michael KD5DFB


Re: Interface ASL into existing bridge

Michael KD5DFB
 

I have a c-bridge to p25 reflector bridge

cbridge<-->IPSC_Bridge<-->Analog_Bridge_DMR<-->Analog_Bridge_P25<-->MMDVM_Bridge<-->P25Gateway<-->P25Reflector  


On Wed, Jan 2, 2019 at 7:07 PM JJ Cummings <cummingsj@...> wrote:
Much much more info is needed, that said the answer is likely YES that you can interface ASL into existing bridges for other modes also.... but each has its own complexities and there is no single answer to interface ASL into an existing ambiguous bridge ;-P

On Wed, Jan 2, 2019 at 6:04 PM Mike KB8JNM <groupio@...> wrote:

Would you like to say what kind of bridge ?

Or

Exactly what you are trying to achieve ?

...mike/kb8jnm


On 1/2/2019 6:29 PM, KD5DFB wrote:
Hello, Group,

Is there a way to interface ASL into an existing bridge?

Michael KD5DFB


Re: Interface ASL into existing bridge

JJ Cummings
 

Much much more info is needed, that said the answer is likely YES that you can interface ASL into existing bridges for other modes also.... but each has its own complexities and there is no single answer to interface ASL into an existing ambiguous bridge ;-P


On Wed, Jan 2, 2019 at 6:04 PM Mike KB8JNM <groupio@...> wrote:

Would you like to say what kind of bridge ?

Or

Exactly what you are trying to achieve ?

...mike/kb8jnm


On 1/2/2019 6:29 PM, KD5DFB wrote:
Hello, Group,

Is there a way to interface ASL into an existing bridge?

Michael KD5DFB


Re: Interface ASL into existing bridge

Mike KB8JNM
 

Would you like to say what kind of bridge ?

Or

Exactly what you are trying to achieve ?

...mike/kb8jnm


On 1/2/2019 6:29 PM, KD5DFB wrote:
Hello, Group,

Is there a way to interface ASL into an existing bridge?

Michael KD5DFB


Re: P25<-->DMR issue "Still"

Steve N4IRS
 

Go ahead and adjust your levels. md380-emu is having a problem. We can circle back a see waht is going on with the emulator.

On 1/2/19 8:00 PM, Ian Tulley wrote:
That worked Steve, thanks, other than very low Audio from P25 to DMR, using the settings both as 1.0 it is now working fine, so I will need to adjust those settings to get it going correctly. I didn’t think of that for the DMR side ??


Regards
Ian (VK2HK)





On 3 Jan 2019, at 11:44 am, Ian Tulley <ian@...> wrote:

Hi Steve, wasn’t sure if you wanted it as an attachment, hoping it works via the group.




Regards
Ian (VK2HK)





On 3 Jan 2019, at 10:08 am, Ian Tulley <ian@...> wrote:

OK, still having issues on the audio side, no matter the combination of the Audio Gain etc, it does make some differences but from P25 to DMR you can make out some of the audio but very very broken up, but from DMR to P25 its just garbage.

When I run the Analog_Bridge_P25.ini and TX, this is the last entries I see on the screen so this shows both from DMR to P25 and visa versa.

I: 2019-01-02 22:58:32.106 Open UDP listener on 127.0.0.1:34100
I: 2019-01-02 22:58:32.106 Open USRP on 127.0.0.1:32001
M: 2019-01-02 22:58:32.106 Connecting to DV3000 hardware......
W: 2019-01-02 22:58:33.115 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 22:58:33.214 Subscriber IDs loaded: 117848
I: 2019-01-02 22:58:33.215 Default extended metadata <VK2HK>
W: 2019-01-02 22:58:33.215 Using software MBE decoder version 1.2.3
W: 2019-01-02 22:58:33.215 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 22:58:33.215 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 22:58:33.215 Open UDP listener on 127.0.0.1:34001
I: 2019-01-02 22:58:33.215 Starting USRP --> IPSC_Bridge thread
I: 2019-01-02 23:02:56.562 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:02:57.062 PTT on
M: 2019-01-02 23:02:59.907 PTT off (keyed for 2845 ms)
I: 2019-01-02 23:03:13.110 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0


This is the same but from the Analog_Bridge_DMR.ini

I: 2019-01-02 23:02:38.868 Open UDP listener on 127.0.0.1:31100
I: 2019-01-02 23:02:38.868 Open USRP on 127.0.0.1:34001
D: 2019-01-02 23:02:38.868 Attempt to  init DV3000 in DMR mode
M: 2019-01-02 23:02:38.868 Connecting to DV3000 hardware......
W: 2019-01-02 23:02:39.881 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 23:02:39.986 Subscriber IDs loaded: 117848
I: 2019-01-02 23:02:39.987 Default extended metadata <50521891>
I: 2019-01-02 23:02:39.987 Connecting to emulator on host 127.0.0.1:2470
W: 2019-01-02 23:02:39.987 Using software MBE decoder version 1.2.3
W: 2019-01-02 23:02:39.987 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 23:02:39.987 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 23:02:39.987 Open UDP listener on 127.0.0.1:32001
I: 2019-01-02 23:02:39.987 Starting USRP --> HB_Bridge thread
I: 2019-01-02 23:02:56.562 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0
D: 2019-01-02 23:02:59.907 End TX
I: 2019-01-02 23:03:13.111 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:03:13.613 PTT on
D: 2019-01-02 23:03:18.694 cpu_time_used = 5081, minTxTime = 2000, pttTime = 1546470193613, end = 1546470198694
M: 2019-01-02 23:03:18.694 PTT off (keyed for 5081 ms)


Just making sure that it looks as it should to you

Regards
Ian (VK2HK)





On 3 Jan 2019, at 7:51 am, Steve N4IRS <szingman@...> wrote:

Set the USRP audio settings in BOTH ini files to:
aslAudio = AUDIO_USE_GAIN
agcGain = 1.0
dmrAudio = AUDIO_USE_GAIN
dmrGain = 1.0

From there you can go up to 1.5,2,etc or down .9,.8,etc.


On 1/2/2019 3:46 PM, Ian Tulley wrote:
Hi Steve, if I do systemctl status md380-emu it shows it as running, if I TX from the P25 radio, I get very broken audio out of the DMR, if I TX from the DMR Radio I just get very harsh hash from the P25 Radio, that was with the USRP Audio settings as per default. I am assuming I will need to adjust those on both of the Analog_Bridge ini files ??

I have not done any as yet this morning, but will be looking at it hopefully in the next hour.

------------------
Regards
Ian (VK2HK)




On 2 Jan 2019, at 9:36 pm, Steve N4IRS <szingman@...> wrote:

So,
it sounds like P25 is working all the way to Analog_Bridge. It also sounds like you have a problem with Analog_Bridge for DMR. 
Are you using the emulator?
Is the emulator running?

Steve

On 1/2/19 2:40 AM, Ian Tulley wrote:
Hi Steve, OK here is what I have been able to achieve, P25Gateway runs fine, I can then start MMDVM_Bridge and it connects to the BM Master successfully, I can TX on both the P25 radio and the DMR radio on different repeaters and see my calls come up on the screen output. I then start up Analog_Bridge_P25.ini and do the same test and again can see myself coming up on the screen output but no audio between them. Now when I startup Analog_Bridge_DMR.ini and do the same test I can see myself come up on the screen output then I get the following error, only on that Stanza, "Emulator Timed out on Decode" or "Emulator Timed out on Encode" depending on the direction of the data and still no audio in either direction, but I can get the DMR repeater to TX "sometimes" when PTT from the P25 radio but no audio.
I'm not sure where to look for this one, please remember this is on a server in the cloud so there are no USB Dongles connected, I'm only using the software decoder.

Regards
Ian (VK2HK) 





<Analog_Bridge_DMR.ini>



Re: P25<-->DMR issue "Still"

Ian Tulley
 

That worked Steve, thanks, other than very low Audio from P25 to DMR, using the settings both as 1.0 it is now working fine, so I will need to adjust those settings to get it going correctly. I didn’t think of that for the DMR side ??


Regards
Ian (VK2HK)





On 3 Jan 2019, at 11:44 am, Ian Tulley <ian@...> wrote:

Hi Steve, wasn’t sure if you wanted it as an attachment, hoping it works via the group.




Regards
Ian (VK2HK)





On 3 Jan 2019, at 10:08 am, Ian Tulley <ian@...> wrote:

OK, still having issues on the audio side, no matter the combination of the Audio Gain etc, it does make some differences but from P25 to DMR you can make out some of the audio but very very broken up, but from DMR to P25 its just garbage.

When I run the Analog_Bridge_P25.ini and TX, this is the last entries I see on the screen so this shows both from DMR to P25 and visa versa.

I: 2019-01-02 22:58:32.106 Open UDP listener on 127.0.0.1:34100
I: 2019-01-02 22:58:32.106 Open USRP on 127.0.0.1:32001
M: 2019-01-02 22:58:32.106 Connecting to DV3000 hardware......
W: 2019-01-02 22:58:33.115 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 22:58:33.214 Subscriber IDs loaded: 117848
I: 2019-01-02 22:58:33.215 Default extended metadata <VK2HK>
W: 2019-01-02 22:58:33.215 Using software MBE decoder version 1.2.3
W: 2019-01-02 22:58:33.215 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 22:58:33.215 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 22:58:33.215 Open UDP listener on 127.0.0.1:34001
I: 2019-01-02 22:58:33.215 Starting USRP --> IPSC_Bridge thread
I: 2019-01-02 23:02:56.562 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:02:57.062 PTT on
M: 2019-01-02 23:02:59.907 PTT off (keyed for 2845 ms)
I: 2019-01-02 23:03:13.110 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0


This is the same but from the Analog_Bridge_DMR.ini

I: 2019-01-02 23:02:38.868 Open UDP listener on 127.0.0.1:31100
I: 2019-01-02 23:02:38.868 Open USRP on 127.0.0.1:34001
D: 2019-01-02 23:02:38.868 Attempt to  init DV3000 in DMR mode
M: 2019-01-02 23:02:38.868 Connecting to DV3000 hardware......
W: 2019-01-02 23:02:39.881 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 23:02:39.986 Subscriber IDs loaded: 117848
I: 2019-01-02 23:02:39.987 Default extended metadata <50521891>
I: 2019-01-02 23:02:39.987 Connecting to emulator on host 127.0.0.1:2470
W: 2019-01-02 23:02:39.987 Using software MBE decoder version 1.2.3
W: 2019-01-02 23:02:39.987 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 23:02:39.987 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 23:02:39.987 Open UDP listener on 127.0.0.1:32001
I: 2019-01-02 23:02:39.987 Starting USRP --> HB_Bridge thread
I: 2019-01-02 23:02:56.562 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0
D: 2019-01-02 23:02:59.907 End TX
I: 2019-01-02 23:03:13.111 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:03:13.613 PTT on
D: 2019-01-02 23:03:18.694 cpu_time_used = 5081, minTxTime = 2000, pttTime = 1546470193613, end = 1546470198694
M: 2019-01-02 23:03:18.694 PTT off (keyed for 5081 ms)


Just making sure that it looks as it should to you

Regards
Ian (VK2HK)





On 3 Jan 2019, at 7:51 am, Steve N4IRS <szingman@...> wrote:

Set the USRP audio settings in BOTH ini files to:
aslAudio = AUDIO_USE_GAIN
agcGain = 1.0
dmrAudio = AUDIO_USE_GAIN
dmrGain = 1.0

From there you can go up to 1.5,2,etc or down .9,.8,etc.


On 1/2/2019 3:46 PM, Ian Tulley wrote:
Hi Steve, if I do systemctl status md380-emu it shows it as running, if I TX from the P25 radio, I get very broken audio out of the DMR, if I TX from the DMR Radio I just get very harsh hash from the P25 Radio, that was with the USRP Audio settings as per default. I am assuming I will need to adjust those on both of the Analog_Bridge ini files ??

I have not done any as yet this morning, but will be looking at it hopefully in the next hour.

------------------
Regards
Ian (VK2HK)




On 2 Jan 2019, at 9:36 pm, Steve N4IRS <szingman@...> wrote:

So,
it sounds like P25 is working all the way to Analog_Bridge. It also sounds like you have a problem with Analog_Bridge for DMR. 
Are you using the emulator?
Is the emulator running?

Steve

On 1/2/19 2:40 AM, Ian Tulley wrote:
Hi Steve, OK here is what I have been able to achieve, P25Gateway runs fine, I can then start MMDVM_Bridge and it connects to the BM Master successfully, I can TX on both the P25 radio and the DMR radio on different repeaters and see my calls come up on the screen output. I then start up Analog_Bridge_P25.ini and do the same test and again can see myself coming up on the screen output but no audio between them. Now when I startup Analog_Bridge_DMR.ini and do the same test I can see myself come up on the screen output then I get the following error, only on that Stanza, "Emulator Timed out on Decode" or "Emulator Timed out on Encode" depending on the direction of the data and still no audio in either direction, but I can get the DMR repeater to TX "sometimes" when PTT from the P25 radio but no audio.
I'm not sure where to look for this one, please remember this is on a server in the cloud so there are no USB Dongles connected, I'm only using the software decoder.

Regards
Ian (VK2HK) 





<Analog_Bridge_DMR.ini>


Re: P25<-->DMR issue "Still"

Steve N4IRS
 

Yes, that works.
As a test in the DMR Analog_Bridge.ini chnge:

useEmulator = true
to
useEmulator = false

and retest


On 1/2/19 7:44 PM, Ian Tulley wrote:
Hi Steve, wasn’t sure if you wanted it as an attachment, hoping it works via the group.




Regards
Ian (VK2HK)





On 3 Jan 2019, at 10:08 am, Ian Tulley <ian@...> wrote:

OK, still having issues on the audio side, no matter the combination of the Audio Gain etc, it does make some differences but from P25 to DMR you can make out some of the audio but very very broken up, but from DMR to P25 its just garbage.

When I run the Analog_Bridge_P25.ini and TX, this is the last entries I see on the screen so this shows both from DMR to P25 and visa versa.

I: 2019-01-02 22:58:32.106 Open UDP listener on 127.0.0.1:34100
I: 2019-01-02 22:58:32.106 Open USRP on 127.0.0.1:32001
M: 2019-01-02 22:58:32.106 Connecting to DV3000 hardware......
W: 2019-01-02 22:58:33.115 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 22:58:33.214 Subscriber IDs loaded: 117848
I: 2019-01-02 22:58:33.215 Default extended metadata <VK2HK>
W: 2019-01-02 22:58:33.215 Using software MBE decoder version 1.2.3
W: 2019-01-02 22:58:33.215 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 22:58:33.215 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 22:58:33.215 Open UDP listener on 127.0.0.1:34001
I: 2019-01-02 22:58:33.215 Starting USRP --> IPSC_Bridge thread
I: 2019-01-02 23:02:56.562 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:02:57.062 PTT on
M: 2019-01-02 23:02:59.907 PTT off (keyed for 2845 ms)
I: 2019-01-02 23:03:13.110 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0


This is the same but from the Analog_Bridge_DMR.ini

I: 2019-01-02 23:02:38.868 Open UDP listener on 127.0.0.1:31100
I: 2019-01-02 23:02:38.868 Open USRP on 127.0.0.1:34001
D: 2019-01-02 23:02:38.868 Attempt to  init DV3000 in DMR mode
M: 2019-01-02 23:02:38.868 Connecting to DV3000 hardware......
W: 2019-01-02 23:02:39.881 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 23:02:39.986 Subscriber IDs loaded: 117848
I: 2019-01-02 23:02:39.987 Default extended metadata <50521891>
I: 2019-01-02 23:02:39.987 Connecting to emulator on host 127.0.0.1:2470
W: 2019-01-02 23:02:39.987 Using software MBE decoder version 1.2.3
W: 2019-01-02 23:02:39.987 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 23:02:39.987 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 23:02:39.987 Open UDP listener on 127.0.0.1:32001
I: 2019-01-02 23:02:39.987 Starting USRP --> HB_Bridge thread
I: 2019-01-02 23:02:56.562 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0
D: 2019-01-02 23:02:59.907 End TX
I: 2019-01-02 23:03:13.111 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:03:13.613 PTT on
D: 2019-01-02 23:03:18.694 cpu_time_used = 5081, minTxTime = 2000, pttTime = 1546470193613, end = 1546470198694
M: 2019-01-02 23:03:18.694 PTT off (keyed for 5081 ms)


Just making sure that it looks as it should to you

Regards
Ian (VK2HK)





On 3 Jan 2019, at 7:51 am, Steve N4IRS <szingman@...> wrote:

Set the USRP audio settings in BOTH ini files to:
aslAudio = AUDIO_USE_GAIN
agcGain = 1.0
dmrAudio = AUDIO_USE_GAIN
dmrGain = 1.0

From there you can go up to 1.5,2,etc or down .9,.8,etc.


On 1/2/2019 3:46 PM, Ian Tulley wrote:
Hi Steve, if I do systemctl status md380-emu it shows it as running, if I TX from the P25 radio, I get very broken audio out of the DMR, if I TX from the DMR Radio I just get very harsh hash from the P25 Radio, that was with the USRP Audio settings as per default. I am assuming I will need to adjust those on both of the Analog_Bridge ini files ??

I have not done any as yet this morning, but will be looking at it hopefully in the next hour.

------------------
Regards
Ian (VK2HK)




On 2 Jan 2019, at 9:36 pm, Steve N4IRS <szingman@...> wrote:

So,
it sounds like P25 is working all the way to Analog_Bridge. It also sounds like you have a problem with Analog_Bridge for DMR. 
Are you using the emulator?
Is the emulator running?

Steve

On 1/2/19 2:40 AM, Ian Tulley wrote:
Hi Steve, OK here is what I have been able to achieve, P25Gateway runs fine, I can then start MMDVM_Bridge and it connects to the BM Master successfully, I can TX on both the P25 radio and the DMR radio on different repeaters and see my calls come up on the screen output. I then start up Analog_Bridge_P25.ini and do the same test and again can see myself coming up on the screen output but no audio between them. Now when I startup Analog_Bridge_DMR.ini and do the same test I can see myself come up on the screen output then I get the following error, only on that Stanza, "Emulator Timed out on Decode" or "Emulator Timed out on Encode" depending on the direction of the data and still no audio in either direction, but I can get the DMR repeater to TX "sometimes" when PTT from the P25 radio but no audio.
I'm not sure where to look for this one, please remember this is on a server in the cloud so there are no USB Dongles connected, I'm only using the software decoder.

Regards
Ian (VK2HK) 







Re: P25<-->DMR issue "Still"

Ian Tulley
 

I also meant to say, I started again on the Audio gain etc., so what is in the ini file is what I got back to.


Regards
Ian (VK2HK)





On 3 Jan 2019, at 11:44 am, Ian Tulley <ian@...> wrote:

Hi Steve, wasn’t sure if you wanted it as an attachment, hoping it works via the group.




Regards
Ian (VK2HK)





On 3 Jan 2019, at 10:08 am, Ian Tulley <ian@...> wrote:

OK, still having issues on the audio side, no matter the combination of the Audio Gain etc, it does make some differences but from P25 to DMR you can make out some of the audio but very very broken up, but from DMR to P25 its just garbage.

When I run the Analog_Bridge_P25.ini and TX, this is the last entries I see on the screen so this shows both from DMR to P25 and visa versa.

I: 2019-01-02 22:58:32.106 Open UDP listener on 127.0.0.1:34100
I: 2019-01-02 22:58:32.106 Open USRP on 127.0.0.1:32001
M: 2019-01-02 22:58:32.106 Connecting to DV3000 hardware......
W: 2019-01-02 22:58:33.115 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 22:58:33.214 Subscriber IDs loaded: 117848
I: 2019-01-02 22:58:33.215 Default extended metadata <VK2HK>
W: 2019-01-02 22:58:33.215 Using software MBE decoder version 1.2.3
W: 2019-01-02 22:58:33.215 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 22:58:33.215 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 22:58:33.215 Open UDP listener on 127.0.0.1:34001
I: 2019-01-02 22:58:33.215 Starting USRP --> IPSC_Bridge thread
I: 2019-01-02 23:02:56.562 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:02:57.062 PTT on
M: 2019-01-02 23:02:59.907 PTT off (keyed for 2845 ms)
I: 2019-01-02 23:03:13.110 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0


This is the same but from the Analog_Bridge_DMR.ini

I: 2019-01-02 23:02:38.868 Open UDP listener on 127.0.0.1:31100
I: 2019-01-02 23:02:38.868 Open USRP on 127.0.0.1:34001
D: 2019-01-02 23:02:38.868 Attempt to  init DV3000 in DMR mode
M: 2019-01-02 23:02:38.868 Connecting to DV3000 hardware......
W: 2019-01-02 23:02:39.881 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 23:02:39.986 Subscriber IDs loaded: 117848
I: 2019-01-02 23:02:39.987 Default extended metadata <50521891>
I: 2019-01-02 23:02:39.987 Connecting to emulator on host 127.0.0.1:2470
W: 2019-01-02 23:02:39.987 Using software MBE decoder version 1.2.3
W: 2019-01-02 23:02:39.987 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 23:02:39.987 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 23:02:39.987 Open UDP listener on 127.0.0.1:32001
I: 2019-01-02 23:02:39.987 Starting USRP --> HB_Bridge thread
I: 2019-01-02 23:02:56.562 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0
D: 2019-01-02 23:02:59.907 End TX
I: 2019-01-02 23:03:13.111 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:03:13.613 PTT on
D: 2019-01-02 23:03:18.694 cpu_time_used = 5081, minTxTime = 2000, pttTime = 1546470193613, end = 1546470198694
M: 2019-01-02 23:03:18.694 PTT off (keyed for 5081 ms)


Just making sure that it looks as it should to you

Regards
Ian (VK2HK)





On 3 Jan 2019, at 7:51 am, Steve N4IRS <szingman@...> wrote:

Set the USRP audio settings in BOTH ini files to:
aslAudio = AUDIO_USE_GAIN
agcGain = 1.0
dmrAudio = AUDIO_USE_GAIN
dmrGain = 1.0

From there you can go up to 1.5,2,etc or down .9,.8,etc.


On 1/2/2019 3:46 PM, Ian Tulley wrote:
Hi Steve, if I do systemctl status md380-emu it shows it as running, if I TX from the P25 radio, I get very broken audio out of the DMR, if I TX from the DMR Radio I just get very harsh hash from the P25 Radio, that was with the USRP Audio settings as per default. I am assuming I will need to adjust those on both of the Analog_Bridge ini files ??

I have not done any as yet this morning, but will be looking at it hopefully in the next hour.

------------------
Regards
Ian (VK2HK)




On 2 Jan 2019, at 9:36 pm, Steve N4IRS <szingman@...> wrote:

So,
it sounds like P25 is working all the way to Analog_Bridge. It also sounds like you have a problem with Analog_Bridge for DMR. 
Are you using the emulator?
Is the emulator running?

Steve

On 1/2/19 2:40 AM, Ian Tulley wrote:
Hi Steve, OK here is what I have been able to achieve, P25Gateway runs fine, I can then start MMDVM_Bridge and it connects to the BM Master successfully, I can TX on both the P25 radio and the DMR radio on different repeaters and see my calls come up on the screen output. I then start up Analog_Bridge_P25.ini and do the same test and again can see myself coming up on the screen output but no audio between them. Now when I startup Analog_Bridge_DMR.ini and do the same test I can see myself come up on the screen output then I get the following error, only on that Stanza, "Emulator Timed out on Decode" or "Emulator Timed out on Encode" depending on the direction of the data and still no audio in either direction, but I can get the DMR repeater to TX "sometimes" when PTT from the P25 radio but no audio.
I'm not sure where to look for this one, please remember this is on a server in the cloud so there are no USB Dongles connected, I'm only using the software decoder.

Regards
Ian (VK2HK) 





<Analog_Bridge_DMR.ini>


Re: P25<-->DMR issue "Still"

Ian Tulley
 

Hi Steve, wasn’t sure if you wanted it as an attachment, hoping it works via the group.




Regards
Ian (VK2HK)





On 3 Jan 2019, at 10:08 am, Ian Tulley <ian@...> wrote:

OK, still having issues on the audio side, no matter the combination of the Audio Gain etc, it does make some differences but from P25 to DMR you can make out some of the audio but very very broken up, but from DMR to P25 its just garbage.

When I run the Analog_Bridge_P25.ini and TX, this is the last entries I see on the screen so this shows both from DMR to P25 and visa versa.

I: 2019-01-02 22:58:32.106 Open UDP listener on 127.0.0.1:34100
I: 2019-01-02 22:58:32.106 Open USRP on 127.0.0.1:32001
M: 2019-01-02 22:58:32.106 Connecting to DV3000 hardware......
W: 2019-01-02 22:58:33.115 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 22:58:33.214 Subscriber IDs loaded: 117848
I: 2019-01-02 22:58:33.215 Default extended metadata <VK2HK>
W: 2019-01-02 22:58:33.215 Using software MBE decoder version 1.2.3
W: 2019-01-02 22:58:33.215 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 22:58:33.215 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 22:58:33.215 Open UDP listener on 127.0.0.1:34001
I: 2019-01-02 22:58:33.215 Starting USRP --> IPSC_Bridge thread
I: 2019-01-02 23:02:56.562 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:02:57.062 PTT on
M: 2019-01-02 23:02:59.907 PTT off (keyed for 2845 ms)
I: 2019-01-02 23:03:13.110 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0


This is the same but from the Analog_Bridge_DMR.ini

I: 2019-01-02 23:02:38.868 Open UDP listener on 127.0.0.1:31100
I: 2019-01-02 23:02:38.868 Open USRP on 127.0.0.1:34001
D: 2019-01-02 23:02:38.868 Attempt to  init DV3000 in DMR mode
M: 2019-01-02 23:02:38.868 Connecting to DV3000 hardware......
W: 2019-01-02 23:02:39.881 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 23:02:39.986 Subscriber IDs loaded: 117848
I: 2019-01-02 23:02:39.987 Default extended metadata <50521891>
I: 2019-01-02 23:02:39.987 Connecting to emulator on host 127.0.0.1:2470
W: 2019-01-02 23:02:39.987 Using software MBE decoder version 1.2.3
W: 2019-01-02 23:02:39.987 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 23:02:39.987 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 23:02:39.987 Open UDP listener on 127.0.0.1:32001
I: 2019-01-02 23:02:39.987 Starting USRP --> HB_Bridge thread
I: 2019-01-02 23:02:56.562 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0
D: 2019-01-02 23:02:59.907 End TX
I: 2019-01-02 23:03:13.111 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:03:13.613 PTT on
D: 2019-01-02 23:03:18.694 cpu_time_used = 5081, minTxTime = 2000, pttTime = 1546470193613, end = 1546470198694
M: 2019-01-02 23:03:18.694 PTT off (keyed for 5081 ms)


Just making sure that it looks as it should to you

Regards
Ian (VK2HK)





On 3 Jan 2019, at 7:51 am, Steve N4IRS <szingman@...> wrote:

Set the USRP audio settings in BOTH ini files to:
aslAudio = AUDIO_USE_GAIN
agcGain = 1.0
dmrAudio = AUDIO_USE_GAIN
dmrGain = 1.0

From there you can go up to 1.5,2,etc or down .9,.8,etc.


On 1/2/2019 3:46 PM, Ian Tulley wrote:
Hi Steve, if I do systemctl status md380-emu it shows it as running, if I TX from the P25 radio, I get very broken audio out of the DMR, if I TX from the DMR Radio I just get very harsh hash from the P25 Radio, that was with the USRP Audio settings as per default. I am assuming I will need to adjust those on both of the Analog_Bridge ini files ??

I have not done any as yet this morning, but will be looking at it hopefully in the next hour.

------------------
Regards
Ian (VK2HK)




On 2 Jan 2019, at 9:36 pm, Steve N4IRS <szingman@...> wrote:

So,
it sounds like P25 is working all the way to Analog_Bridge. It also sounds like you have a problem with Analog_Bridge for DMR. 
Are you using the emulator?
Is the emulator running?

Steve

On 1/2/19 2:40 AM, Ian Tulley wrote:
Hi Steve, OK here is what I have been able to achieve, P25Gateway runs fine, I can then start MMDVM_Bridge and it connects to the BM Master successfully, I can TX on both the P25 radio and the DMR radio on different repeaters and see my calls come up on the screen output. I then start up Analog_Bridge_P25.ini and do the same test and again can see myself coming up on the screen output but no audio between them. Now when I startup Analog_Bridge_DMR.ini and do the same test I can see myself come up on the screen output then I get the following error, only on that Stanza, "Emulator Timed out on Decode" or "Emulator Timed out on Encode" depending on the direction of the data and still no audio in either direction, but I can get the DMR repeater to TX "sometimes" when PTT from the P25 radio but no audio.
I'm not sure where to look for this one, please remember this is on a server in the cloud so there are no USB Dongles connected, I'm only using the software decoder.

Regards
Ian (VK2HK) 






Re: Setting up DMRLink <-> KBLink #best_practices #dmrlink #hblink

Cort N0MJS <n0mjs@...>
 

Actually, this is exactly how I set up a new system… but yes, I also show off a little too. I think I earned it, don’t you?

Point is, keep it simple :)

On Jan 2, 2019, at 6:25 PM, Peter M0NWI <peter-martin@...> wrote:

Now you’re just showing off 😁😂😂
From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of Cort N0MJS via Groups.Io <n0mjs@...>
Sent: 03 January 2019 00:08:49
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] Setting up DMRLink <-> KBLink #best_practices #dmrlink #hblink
 
cort@ubuntu:~$ more /etc/issue
Ubuntu 16.04.5 LTS \n \l

cort@ubuntu:~$ su
# OUTPUT OF THE FOLLOWING COMMANDS NOT INCLUDED
root@ubuntu:/home/cort# apt-get install git
root@ubuntu:/home/cort# apt-get install python-pip
root@ubuntu:/home/cort# apt-get install python-twisted
root@ubuntu:/home/cort# pip install dmr_utils
root@ubuntu:/home/cort# exit

cort@ubuntu:~$ git clone git://github.com/n0mjs710/hblink
cort@ubuntu:~$ cd hblink
cort@ubuntu:~/hblink$ cp hblink-SAMPLE.cfg hblink.cfg

# OUTPUT OF THE FOLLOWING COMMAND IS INCLUDED
cort@ubuntu:~/hblink$ python hblink.py
INFO 2019-01-02 18:03:45,614 

Copyright (c) 2013, 2014, 2015, 2016, 2018
The Founding Members of the K0USY Group. All rights reserved.

DEBUG 2019-01-02 18:03:45,615 Logging system started, anything from here on gets logged
INFO 2019-01-02 18:03:51,752 ID ALIAS MAPPER: 'peer_ids.csv' successfully downloaded
INFO 2019-01-02 18:03:59,630 ID ALIAS MAPPER: 'subscriber_ids.csv' successfully downloaded
INFO 2019-01-02 18:03:59,644 ID ALIAS MAPPER: peer_ids dictionary is available
INFO 2019-01-02 18:03:59,811 ID ALIAS MAPPER: subscriber_ids dictionary is available
INFO 2019-01-02 18:03:59,812 HBlink TCP reporting server configured
DEBUG 2019-01-02 18:03:59,813 Periodic reporting loop started
INFO 2019-01-02 18:03:59,813 HBlink 'HBlink.py' -- SYSTEM STARTING...
DEBUG 2019-01-02 18:03:59,814 (MASTER-1) Master maintenance loop started
DEBUG 2019-01-02 18:03:59,814 MASTER instance created: MASTER-1, <__main__.HBSYSTEM instance at 0x7f6425833b90>
DEBUG 2019-01-02 18:03:59,815 (REPEATER-1) Peer maintenance loop started
INFO 2019-01-02 18:03:59,815 (REPEATER-1) Sending login request to master 172.16.1.1:54000
DEBUG 2019-01-02 18:03:59,815 PEER instance created: REPEATER-1, <__main__.HBSYSTEM instance at 0x7f6425833d88>
DEBUG 2019-01-02 18:03:59,816 OPENBRIDGE instance created: OBP-1, <__main__.OPENBRIDGE instance at 0x7f642583d050>
DEBUG 2019-01-02 18:04:04,820 (MASTER-1) Master maintenance loop started
DEBUG 2019-01-02 18:04:04,820 (REPEATER-1) Peer maintenance loop started
INFO 2019-01-02 18:04:04,821 (REPEATER-1) Sending login request to master 172.16.1.1:54000
^CINFO 2019-01-02 18:04:07,507 SHUTDOWN: HBLINK IS TERMINATING WITH SIGNAL 2
INFO 2019-01-02 18:04:07,508 SHUTDOWN: DE-REGISTER SYSTEM: MASTER-1
INFO 2019-01-02 18:04:07,508 SHUTDOWN: DE-REGISTER SYSTEM: REPEATER-1
INFO 2019-01-02 18:04:07,508 (REPEATER-1) De-Registration sent to Master: 172.16.1.1:54000
INFO 2019-01-02 18:04:07,508 SHUTDOWN: DE-REGISTER SYSTEM: OBP-1
INFO 2019-01-02 18:04:07,508 (OBP-1) is mode OPENBRIDGE. No De-Registration required, continuing shutdown
INFO 2019-01-02 18:04:07,508 SHUTDOWN: ALL SYSTEM HANDLERS EXECUTED - STOPPING REACTOR
cort@ubuntu:~/hblink$


On Jan 2, 2019, at 5:15 PM, Jason Johnston <kc5hwb@...> wrote:

That sounds great, no rush.  Thanks for your continued help.

--
Cort Buffington
H: +1-785-813-1501
M: +1-785-865-7206






--
Cort Buffington
H: +1-785-813-1501
M: +1-785-865-7206






Re: Setting up DMRLink <-> KBLink #best_practices #dmrlink #hblink

Peter M0NWI
 

Now you’re just showing off 😁😂😂
From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of Cort N0MJS via Groups.Io <n0mjs@...>
Sent: 03 January 2019 00:08:49
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] Setting up DMRLink <-> KBLink #best_practices #dmrlink #hblink
 
cort@ubuntu:~$ more /etc/issue
Ubuntu 16.04.5 LTS \n \l

cort@ubuntu:~$ su
# OUTPUT OF THE FOLLOWING COMMANDS NOT INCLUDED
root@ubuntu:/home/cort# apt-get install git
root@ubuntu:/home/cort# apt-get install python-pip
root@ubuntu:/home/cort# apt-get install python-twisted
root@ubuntu:/home/cort# pip install dmr_utils
root@ubuntu:/home/cort# exit

cort@ubuntu:~$ git clone git://github.com/n0mjs710/hblink
cort@ubuntu:~$ cd hblink
cort@ubuntu:~/hblink$ cp hblink-SAMPLE.cfg hblink.cfg

# OUTPUT OF THE FOLLOWING COMMAND IS INCLUDED
cort@ubuntu:~/hblink$ python hblink.py
INFO 2019-01-02 18:03:45,614 

Copyright (c) 2013, 2014, 2015, 2016, 2018
The Founding Members of the K0USY Group. All rights reserved.

DEBUG 2019-01-02 18:03:45,615 Logging system started, anything from here on gets logged
INFO 2019-01-02 18:03:51,752 ID ALIAS MAPPER: 'peer_ids.csv' successfully downloaded
INFO 2019-01-02 18:03:59,630 ID ALIAS MAPPER: 'subscriber_ids.csv' successfully downloaded
INFO 2019-01-02 18:03:59,644 ID ALIAS MAPPER: peer_ids dictionary is available
INFO 2019-01-02 18:03:59,811 ID ALIAS MAPPER: subscriber_ids dictionary is available
INFO 2019-01-02 18:03:59,812 HBlink TCP reporting server configured
DEBUG 2019-01-02 18:03:59,813 Periodic reporting loop started
INFO 2019-01-02 18:03:59,813 HBlink 'HBlink.py' -- SYSTEM STARTING...
DEBUG 2019-01-02 18:03:59,814 (MASTER-1) Master maintenance loop started
DEBUG 2019-01-02 18:03:59,814 MASTER instance created: MASTER-1, <__main__.HBSYSTEM instance at 0x7f6425833b90>
DEBUG 2019-01-02 18:03:59,815 (REPEATER-1) Peer maintenance loop started
INFO 2019-01-02 18:03:59,815 (REPEATER-1) Sending login request to master 172.16.1.1:54000
DEBUG 2019-01-02 18:03:59,815 PEER instance created: REPEATER-1, <__main__.HBSYSTEM instance at 0x7f6425833d88>
DEBUG 2019-01-02 18:03:59,816 OPENBRIDGE instance created: OBP-1, <__main__.OPENBRIDGE instance at 0x7f642583d050>
DEBUG 2019-01-02 18:04:04,820 (MASTER-1) Master maintenance loop started
DEBUG 2019-01-02 18:04:04,820 (REPEATER-1) Peer maintenance loop started
INFO 2019-01-02 18:04:04,821 (REPEATER-1) Sending login request to master 172.16.1.1:54000
^CINFO 2019-01-02 18:04:07,507 SHUTDOWN: HBLINK IS TERMINATING WITH SIGNAL 2
INFO 2019-01-02 18:04:07,508 SHUTDOWN: DE-REGISTER SYSTEM: MASTER-1
INFO 2019-01-02 18:04:07,508 SHUTDOWN: DE-REGISTER SYSTEM: REPEATER-1
INFO 2019-01-02 18:04:07,508 (REPEATER-1) De-Registration sent to Master: 172.16.1.1:54000
INFO 2019-01-02 18:04:07,508 SHUTDOWN: DE-REGISTER SYSTEM: OBP-1
INFO 2019-01-02 18:04:07,508 (OBP-1) is mode OPENBRIDGE. No De-Registration required, continuing shutdown
INFO 2019-01-02 18:04:07,508 SHUTDOWN: ALL SYSTEM HANDLERS EXECUTED - STOPPING REACTOR
cort@ubuntu:~/hblink$


On Jan 2, 2019, at 5:15 PM, Jason Johnston <kc5hwb@...> wrote:

That sounds great, no rush.  Thanks for your continued help.

--
Cort Buffington
H: +1-785-813-1501
M: +1-785-865-7206






Re: P25<-->DMR issue "Still"

Steve N4IRS
 

Ian,
Please show me your Analog_Bridge.ini for DMR.

Steve

On 1/2/19 6:08 PM, Ian Tulley wrote:
OK, still having issues on the audio side, no matter the combination of the Audio Gain etc, it does make some differences but from P25 to DMR you can make out some of the audio but very very broken up, but from DMR to P25 its just garbage.

When I run the Analog_Bridge_P25.ini and TX, this is the last entries I see on the screen so this shows both from DMR to P25 and visa versa.

I: 2019-01-02 22:58:32.106 Open UDP listener on 127.0.0.1:34100
I: 2019-01-02 22:58:32.106 Open USRP on 127.0.0.1:32001
M: 2019-01-02 22:58:32.106 Connecting to DV3000 hardware......
W: 2019-01-02 22:58:33.115 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 22:58:33.214 Subscriber IDs loaded: 117848
I: 2019-01-02 22:58:33.215 Default extended metadata <VK2HK>
W: 2019-01-02 22:58:33.215 Using software MBE decoder version 1.2.3
W: 2019-01-02 22:58:33.215 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 22:58:33.215 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 22:58:33.215 Open UDP listener on 127.0.0.1:34001
I: 2019-01-02 22:58:33.215 Starting USRP --> IPSC_Bridge thread
I: 2019-01-02 23:02:56.562 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:02:57.062 PTT on
M: 2019-01-02 23:02:59.907 PTT off (keyed for 2845 ms)
I: 2019-01-02 23:03:13.110 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0


This is the same but from the Analog_Bridge_DMR.ini

I: 2019-01-02 23:02:38.868 Open UDP listener on 127.0.0.1:31100
I: 2019-01-02 23:02:38.868 Open USRP on 127.0.0.1:34001
D: 2019-01-02 23:02:38.868 Attempt to  init DV3000 in DMR mode
M: 2019-01-02 23:02:38.868 Connecting to DV3000 hardware......
W: 2019-01-02 23:02:39.881 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2019-01-02 23:02:39.986 Subscriber IDs loaded: 117848
I: 2019-01-02 23:02:39.987 Default extended metadata <50521891>
I: 2019-01-02 23:02:39.987 Connecting to emulator on host 127.0.0.1:2470
W: 2019-01-02 23:02:39.987 Using software MBE decoder version 1.2.3
W: 2019-01-02 23:02:39.987 Using software OP25 IMBE/AMBE vocoder
I: 2019-01-02 23:02:39.987 Starting Analog_Bridge --> USRP thread
I: 2019-01-02 23:02:39.987 Open UDP listener on 127.0.0.1:32001
I: 2019-01-02 23:02:39.987 Starting USRP --> HB_Bridge thread
I: 2019-01-02 23:02:56.562 Begin TX: src=5052110 rpt=0 dst=50525 slot=2 cc=0
D: 2019-01-02 23:02:59.907 End TX
I: 2019-01-02 23:03:13.111 USRP packet type: USRP_TYPE_TEXT (VK2HK) -> 5052110
M: 2019-01-02 23:03:13.613 PTT on
D: 2019-01-02 23:03:18.694 cpu_time_used = 5081, minTxTime = 2000, pttTime = 1546470193613, end = 1546470198694
M: 2019-01-02 23:03:18.694 PTT off (keyed for 5081 ms)


Just making sure that it looks as it should to you

Regards
Ian (VK2HK)





On 3 Jan 2019, at 7:51 am, Steve N4IRS <szingman@...> wrote:

Set the USRP audio settings in BOTH ini files to:
aslAudio = AUDIO_USE_GAIN
agcGain = 1.0
dmrAudio = AUDIO_USE_GAIN
dmrGain = 1.0

From there you can go up to 1.5,2,etc or down .9,.8,etc.


On 1/2/2019 3:46 PM, Ian Tulley wrote:
Hi Steve, if I do systemctl status md380-emu it shows it as running, if I TX from the P25 radio, I get very broken audio out of the DMR, if I TX from the DMR Radio I just get very harsh hash from the P25 Radio, that was with the USRP Audio settings as per default. I am assuming I will need to adjust those on both of the Analog_Bridge ini files ??

I have not done any as yet this morning, but will be looking at it hopefully in the next hour.

------------------
Regards
Ian (VK2HK)




On 2 Jan 2019, at 9:36 pm, Steve N4IRS <szingman@...> wrote:

So,
it sounds like P25 is working all the way to Analog_Bridge. It also sounds like you have a problem with Analog_Bridge for DMR.
Are you using the emulator?
Is the emulator running?

Steve

On 1/2/19 2:40 AM, Ian Tulley wrote:
Hi Steve, OK here is what I have been able to achieve, P25Gateway runs fine, I can then start MMDVM_Bridge and it connects to the BM Master successfully, I can TX on both the P25 radio and the DMR radio on different repeaters and see my calls come up on the screen output. I then start up Analog_Bridge_P25.ini and do the same test and again can see myself coming up on the screen output but no audio between them. Now when I startup Analog_Bridge_DMR.ini and do the same test I can see myself come up on the screen output then I get the following error, only on that Stanza, "Emulator Timed out on Decode" or "Emulator Timed out on Encode" depending on the direction of the data and still no audio in either direction, but I can get the DMR repeater to TX "sometimes" when PTT from the P25 radio but no audio.
I'm not sure where to look for this one, please remember this is on a server in the cloud so there are no USB Dongles connected, I'm only using the software decoder.

Regards
Ian (VK2HK)






Re: Setting up DMRLink <-> KBLink #best_practices #dmrlink #hblink

Cort N0MJS <n0mjs@...>
 

cort@ubuntu:~$ more /etc/issue
Ubuntu 16.04.5 LTS \n \l

cort@ubuntu:~$ su
# OUTPUT OF THE FOLLOWING COMMANDS NOT INCLUDED
root@ubuntu:/home/cort# apt-get install git
root@ubuntu:/home/cort# apt-get install python-pip
root@ubuntu:/home/cort# apt-get install python-twisted
root@ubuntu:/home/cort# pip install dmr_utils
root@ubuntu:/home/cort# exit

cort@ubuntu:~$ git clone git://github.com/n0mjs710/hblink
cort@ubuntu:~$ cd hblink
cort@ubuntu:~/hblink$ cp hblink-SAMPLE.cfg hblink.cfg

# OUTPUT OF THE FOLLOWING COMMAND IS INCLUDED
cort@ubuntu:~/hblink$ python hblink.py
INFO 2019-01-02 18:03:45,614 

Copyright (c) 2013, 2014, 2015, 2016, 2018
The Founding Members of the K0USY Group. All rights reserved.

DEBUG 2019-01-02 18:03:45,615 Logging system started, anything from here on gets logged
INFO 2019-01-02 18:03:51,752 ID ALIAS MAPPER: 'peer_ids.csv' successfully downloaded
INFO 2019-01-02 18:03:59,630 ID ALIAS MAPPER: 'subscriber_ids.csv' successfully downloaded
INFO 2019-01-02 18:03:59,644 ID ALIAS MAPPER: peer_ids dictionary is available
INFO 2019-01-02 18:03:59,811 ID ALIAS MAPPER: subscriber_ids dictionary is available
INFO 2019-01-02 18:03:59,812 HBlink TCP reporting server configured
DEBUG 2019-01-02 18:03:59,813 Periodic reporting loop started
INFO 2019-01-02 18:03:59,813 HBlink 'HBlink.py' -- SYSTEM STARTING...
DEBUG 2019-01-02 18:03:59,814 (MASTER-1) Master maintenance loop started
DEBUG 2019-01-02 18:03:59,814 MASTER instance created: MASTER-1, <__main__.HBSYSTEM instance at 0x7f6425833b90>
DEBUG 2019-01-02 18:03:59,815 (REPEATER-1) Peer maintenance loop started
INFO 2019-01-02 18:03:59,815 (REPEATER-1) Sending login request to master 172.16.1.1:54000
DEBUG 2019-01-02 18:03:59,815 PEER instance created: REPEATER-1, <__main__.HBSYSTEM instance at 0x7f6425833d88>
DEBUG 2019-01-02 18:03:59,816 OPENBRIDGE instance created: OBP-1, <__main__.OPENBRIDGE instance at 0x7f642583d050>
DEBUG 2019-01-02 18:04:04,820 (MASTER-1) Master maintenance loop started
DEBUG 2019-01-02 18:04:04,820 (REPEATER-1) Peer maintenance loop started
INFO 2019-01-02 18:04:04,821 (REPEATER-1) Sending login request to master 172.16.1.1:54000
^CINFO 2019-01-02 18:04:07,507 SHUTDOWN: HBLINK IS TERMINATING WITH SIGNAL 2
INFO 2019-01-02 18:04:07,508 SHUTDOWN: DE-REGISTER SYSTEM: MASTER-1
INFO 2019-01-02 18:04:07,508 SHUTDOWN: DE-REGISTER SYSTEM: REPEATER-1
INFO 2019-01-02 18:04:07,508 (REPEATER-1) De-Registration sent to Master: 172.16.1.1:54000
INFO 2019-01-02 18:04:07,508 SHUTDOWN: DE-REGISTER SYSTEM: OBP-1
INFO 2019-01-02 18:04:07,508 (OBP-1) is mode OPENBRIDGE. No De-Registration required, continuing shutdown
INFO 2019-01-02 18:04:07,508 SHUTDOWN: ALL SYSTEM HANDLERS EXECUTED - STOPPING REACTOR
cort@ubuntu:~/hblink$


On Jan 2, 2019, at 5:15 PM, Jason Johnston <kc5hwb@...> wrote:

That sounds great, no rush.  Thanks for your continued help.

--
Cort Buffington
H: +1-785-813-1501
M: +1-785-865-7206





7081 - 7100 of 9775