Date   

Re: Is this even possible?

Jim Gifford - K9AGR
 

I left this running without tinkering over the weekend, and everything stayed rock solid.  The audio issue disappeared for the most part.  I even updated the MD-9600 to have the same settings for listening to the MMDVM box.  It’s worth noting that the MMDVM “repeater” in this case is a cheap duplex chinaspot that I’m running on my coordinated frequency while I finish building my real MMDVM repeater.  The chinaspot can’t be heard more than 25 feet away, and I haven’t dialed in the frequency with mmdvmcal yet.  I’m still learning how to use my service monitor.  It’s adequate to prove the concept, but not adequate to use for an extended QSO yet.

Watching the pi-star dashboard, I saw very few incidents of any packet loss, and in every case I followed up on, the same loss was reflected in the cBridge, so it was lacking in the source signal.

Even though it goes against my OCD-like nature, I’m ignoring the log files from IPSC_Bridge that say extremely high packet loss, as I suspect it’s a reporting bug, not a real bug.  Every single transmission only shows 3 received out of all the ones transmitted.  I’m assuming packets.

Example (times in UTC):
INFO 2018-11-26 12:22:16,271 Voice Transmission Start on TS 1 and TG 8802 (8802) from 3110063 (3110063)
INFO 2018-11-26 12:22:24,371 Voice Transmission End 8.10 seconds loss rate: 97.78% (3/135)
INFO 2018-11-26 12:22:27,791 Voice Transmission Start on TS 1 and TG 8802 (8802) from 3110037 (3110037)
INFO 2018-11-26 12:22:38,412 Voice Transmission End 10.62 seconds loss rate: 98.31% (3/177)
INFO 2018-11-26 12:22:40,691 Voice Transmission Start on TS 1 and TG 8802 (8802) from 3110063 (3110063)
INFO 2018-11-26 12:22:54,551 Voice Transmission End 13.86 seconds loss rate: 98.70% (3/231)
INFO 2018-11-26 12:23:10,871 Voice Transmission Start on TS 1 and TG 8802 (8802) from 3110037 (3110037)
INFO 2018-11-26 12:23:17,172 Voice Transmission End 6.30 seconds loss rate: 97.14% (3/105)
INFO 2018-11-26 12:23:19,571 Voice Transmission Start on TS 1 and TG 8802 (8802) from 3110063 (3110063)
INFO 2018-11-26 12:23:36,671 Voice Transmission End 17.10 seconds loss rate: 98.95% (3/285)
INFO 2018-11-26 12:23:37,631 Voice Transmission Start on TS 1 and TG 8802 (8802) from 3110037 (3110037)
INFO 2018-11-26 12:23:41,771 Voice Transmission End 4.14 seconds loss rate: 95.65% (3/69)
INFO 2018-11-26 12:26:05,230 Voice Transmission Start on TS 2 and TG 3151 (3151) from 3151152 (3151152)
INFO 2018-11-26 12:26:08,648 Voice Transmission End 3.42 seconds loss rate: 94.74% (3/57)
INFO 2018-11-26 12:51:53,708 Voice Transmission Start on TS 2 and TG 3151 (3151) from 3151584 (3151584)
INFO 2018-11-26 12:51:54,967 Voice Transmission End 1.26 seconds loss rate: 85.71% (3/21)
INFO 2018-11-26 13:07:20,770 Voice Transmission Start on TS 2 and TG 3151 (3151) from 3151406 (3151406)
INFO 2018-11-26 13:07:26,346 Voice Transmission End 5.58 seconds loss rate: 96.77% (3/93)
INFO 2018-11-26 13:26:16,994 Voice Transmission Start on TS 1 and TG 8802 (8802) from 3120699 (3120699)
INFO 2018-11-26 13:26:20,411 Voice Transmission End 3.42 seconds loss rate: 94.74% (3/57)
INFO 2018-11-26 13:30:37,633 Voice Transmission Start on TS 1 and TG 8802 (8802) from 3110037 (3110037)
INFO 2018-11-26 13:30:41,772 Voice Transmission End 4.14 seconds loss rate: 95.65% (3/69)
INFO 2018-11-26 13:31:53,650 Voice Transmission Start on TS 2 and TG 3151 (3151) from 3151090 (3151090)
INFO 2018-11-26 13:31:54,547 Voice Transmission End 0.90 seconds loss rate: 80.00% (3/15)

Now, since it is *always* (3/X), this must be an artifact within the code, not the signal, since I can copy the entire transmission on the radio at the endpoint.  Definitely not enough of an issue to bother tracking down at this point.

This software works great, and the CPU usage stats for my virtual server show it doesn’t even break idle.  I’m ready to start making the setup a little more complex now that I have a feel for how it all works together.

Thank you to everyone that has helped me get to this point.  Reading through the archive of topics was educational, but not as much as actually getting some piece of the system operational.  I especially want to thank Corey for his off-list assistance and helping me understand I wasn’t really ready to do what I was attempting to do, and that I needed to start smaller and work my way up.

Thanks,
Jim

On Nov 23, 2018, at 7:52 PM, Corey Dean N3FE <n3fe@...> wrote:

I have seen that same thing happen when the audio lets are not set correctly.  The 868 and 878 are pretty picky on audio levels.

Corey N3FE

On Fri, Nov 23, 2018 at 7:14 PM Jim Gifford - KD4PPG <jim@...> wrote:
I spent time today going back and forth with Corey, and he has been most helpful.  Since he’s using things not yet intended for general consumption, I’ve decided to hold off until that’s out, and instead focus my attention on simplifying the model so that I can finally get my head around how all the pieces glue together.

I’ve spent quite a lot of time today working with IPSC_Bridge and HB_Bridge, and now have the simplest possible setup I could do.  I’ve passed audio traffic through from end to end in both directions, but have some issues still.

MMDVM Repeater <-> HB_Bridge <-> IPSC_Bridge <-> K4USD cBridge

TS1: TG8802
TS2 TG3151

So far, it all looks good, but I have a few concerns.  Earlier today, I was having a QSO over 8802 via the MMDVM repeater, when it stopped making it through the pipeline all the way to K4USD.  I wasn’t able to determine where it was failing, and switched to a direct RF link to a known operational repeater to finish the QSO.

I eventually decided it must’ve been an errant talkgroup from the cBridge, and sent the list of talkgroups I’ve been receiving unsolicited to the cBridge maintainer, and he fixed that when he got home tonight.  So now I’m sitting down and testing again.

Just a couple of minutes ago, I heard a ham call out on the 8802 talkgroup via the radio connected to the known good repeater (40+ miles away), but the HT listening to the benchtop repeater had no audio output at all.  Everything else looked normal, the pi-star dashboard showed the contact, that TX was occurring, etc.  The AnyTone 878 showed the contact information, talkgroup, etc, and updated the last call info after he finished talking.

Here’s the output from IPSC_Bridge:

INFO 2018-11-23 23:54:31,694 Voice Transmission Start on TS 1 and TG 8802 (8802) from 3121792 (3121792)
INFO 2018-11-23 23:54:34,392 Voice Transmission End 2.70 seconds loss rate: 93.33% (3/45)
INFO 2018-11-23 23:56:06,731 Voice Transmission Start on TS 1 and TG 8802 (8802) from 3121792 (3121792)
INFO 2018-11-23 23:56:11,592 Voice Transmission End 4.86 seconds loss rate: 96.30% (3/81)
INFO 2018-11-23 23:57:41,114 Voice Transmission Start on TS 1 and TG 8802 (8802) from 3111697 (3111697)
INFO 2018-11-23 23:57:45,252 Voice Transmission End 4.14 seconds loss rate: 95.65% (3/69)

Here’s the output from HB_Bridge:

INFO 2018-11-23 23:54:31,692 (MASTER-1) Begin AMBE encode STREAM ID: 3929710726 SUB: 3121792 (3121792) REPEATER: 13100030 (13100030) TGID 8802 (8802), TS 1
INFO 2018-11-23 23:56:06,732 (MASTER-1) Begin AMBE encode STREAM ID: 725990770 SUB: 3121792 (3121792) REPEATER: 13100030 (13100030) TGID 8802 (8802), TS 1
INFO 2018-11-23 23:57:41,112 (MASTER-1) Begin AMBE encode STREAM ID: 754258576 SUB: 3111697 (3111697) REPEATER: 13100030 (13100030) TGID 8802 (8802), TS 1

Now that loss rate from IPSC_Bridge worried me when I first discovered it, but since I was actually passing audio both ways earlier today when it was happening, I figured it wasn’t worth worrying about, probably just mis-reporting.  Notice how it’s always 3 out of however many. Always.  But now I wonder if it’s indicative of a problem I should track down.

Any ideas what I should check next?

In terms of setting up confbridge, which is preferred to work with, the one in dmrlink or the one in hblink?  Ultimately, I want one of those to be the primary decision maker in the “center” of it all.  With the link to BM being the most number of talkgroups, I’m leaning towards the hblink one as the one to use.

Thanks,
Jim

On Nov 23, 2018, at 7:14 AM, Jim Gifford - KD4PPG <jim@...> wrote:

I've reached the point where I need someone with experience with these tools to point me in the right direction.  I think I am getting overwhelmed with too much "there's more than one way to do it" combined with not knowing the limitations of the various branches of dmrlink and hblink (IPSC_Bridge and HB_Bridge specifically).

I have the need to connect 2 repeaters up to 2 different networks simultaneously.  One repeater is Mototrbo/IPSC and the other is MMDVM/Pi-Star.  One of the networks is a cBridge, and the other is Brandmeister.

On the IPSC repeater, the requirement is to have TS1 TG8802 and TS2 TG3151 by default, with TG8802 sourced from the cBridge, and TG3151 sourced from either the cBridge or Brandmeister.  I can get it from either source, but TG8802 is only from the cBridge due to policy.  The part that makes it difficult for me to know how to implement it is that the repeater owner wants TS1 to share with "any possible" BM TG, with a PTT setup with 15 minute timeout to revert to TG8802.

On the MMDVM repeater, the requirement is to have TS1 TG8802 and TS2 TG3151 by default.  Again, TG8802 sourced from the cBridge, and TG3151 from either.  The repeater owner on this one is me, and I'd rather have my PTT groups on TS2, and I don't necessarily care if it is "any possible" BM TG or simply a predefined subset.

Eventually, we might add additional DMR repeaters into the mix, and have different requirements for them.

I've started with a pristine install of Ubuntu 18.04 LTS, updated it, added Steve's DVSwitch-System-Builder script, and followed its directions.

Any suggestions for the best way to implement the system as described, or as closely as possible?

Thanks in advance,
Jim KD4PPG






Re: Installing DVSwitch

Steve N4IRS
 

The Draft DMRGateway Install notes is no longer valid. All of the programs have been replaced. Use https://docs.google.com/document/d/1eN50Csr29eAprBu7eKA0Bfa2XUcsXw5iktY1Ey-Qjkg/edit?usp=sharing

On 11/26/18 7:03 AM, Guillermo HK4KM via Groups.Io wrote:
Ok I can now see that maybe the problem with the Draft DMRGateway Install notes is that I did not use the image 

http://dvswitch.org/files/DIAL/RAT_RC1.tar.gz

because it no longer exists at that URL.  So I used a normal Raspbian image.  That maybe explains why the files to contiune installing are not there.

So I will have to look at the other document in more detail.

What I really want to do is transcode/link YSF<->D-Star.  I already have two reflectors running in a single Tinkerboard. And, after that is working I want to connect those to IRN.  I have a channel set up there.  Or, I can use my own TeamSpeak 3 server which is up and running.

Don't know if all this sounds crazy or if it can be done.  Just got pointed to DVSwitch by the IRN guys.

Appreciate any help with this idea and where I may be wrong or what I can and can't do.

73 de Guillermo, HK4KM




Re: Installing DVSwitch

Guillermo HK4KM <hk4km@...>
 

Ok I can now see that maybe the problem with the Draft DMRGateway Install notes is that I did not use the image 

http://dvswitch.org/files/DIAL/RAT_RC1.tar.gz

because it no longer exists at that URL.  So I used a normal Raspbian image.  That maybe explains why the files to contiune installing are not there.

So I will have to look at the other document in more detail.

What I really want to do is transcode/link YSF<->D-Star.  I already have two reflectors running in a single Tinkerboard. And, after that is working I want to connect those to IRN.  I have a channel set up there.  Or, I can use my own TeamSpeak 3 server which is up and running.

Don't know if all this sounds crazy or if it can be done.  Just got pointed to DVSwitch by the IRN guys.

Appreciate any help with this idea and where I may be wrong or what I can and can't do.

73 de Guillermo, HK4KM



Re: Installing DVSwitch

Steve N4IRS
 

DMRGateway no longer exists. The document is no longer valid. I will be removing the document as soon as I finish this message. Use this document https://docs.google.com/document/d/1eN50Csr29eAprBu7eKA0Bfa2XUcsXw5iktY1Ey-Qjkg/edit?usp=sharing

Steve N4IRS

On 11/26/18 6:46 AM, Guillermo HK4KM via Groups.Io wrote:
Thanks for your reply, Mike.

I went to the Files section on the site and downloaded this:

https://dvswitch.groups.io/g/main/files/Draft%20DMRGateway%20Install%20notes.odt

As I stated in my original message, all goes well until I get to the point where it says:

   4: Copy the proper version of DMRG to the destination directory. Execute cp DMRGateway.armv7 /opt/DMRGateway/ DMRGateway


I don't have a DMRGateway.armv7 file to copy in that directory, nor in any other directory in /srv/DMRGateway




Re: Installing DVSwitch

Guillermo HK4KM <hk4km@...>
 

Thanks for your reply, Mike.

I went to the Files section on the site and downloaded this:

https://dvswitch.groups.io/g/main/files/Draft%20DMRGateway%20Install%20notes.odt

As I stated in my original message, all goes well until I get to the point where it says:

   4: Copy the proper version of DMRG to the destination directory. Execute cp DMRGateway.armv7 /opt/DMRGateway/ DMRGateway


I don't have a DMRGateway.armv7 file to copy in that directory, nor in any other directory in /srv/DMRGateway



Re: Installing DVSwitch

Guillermo HK4KM <hk4km@...>
 

Thanks, Frank.  Will see the video and the other one he has on setting up the Allstar node.

73 de HK4KM - Guillermo


Re: Installing DVSwitch

Frank Decuire
 

Guillermo 

If you are a visual learner check out this YouTube video it worked great for me. The narrator also refers to the document.

Frank k6fed 

On Sunday, November 25, 2018, 5:02 PM, Guillermo HK4KM via Groups.Io <hk4km@...> wrote:

Hello group.

I have been trying to install DVSwitch but following the document "Draft DMRGateway Install Notes", when I get to the Install and test DMRGateway part I can't go beyond point 3 as the file in point 4 does not exist.  Is there a revised document I can follow?

I also tried the 
DVSwitch-System-Builder and that also does not work.

Any complete, correct set of instructions I can find to get this set up?

Thanks in advance.


Re: Installing DVSwitch

Mike KB8JNM
 

Not sure exactly what you are looking at...

Try this.

https://docs.google.com/document/d/1eN50Csr29eAprBu7eKA0Bfa2XUcsXw5iktY1Ey-Qjkg/edit

...mike/kb8jnm

On 11/25/2018 8:02 PM, Guillermo HK4KM via Groups.Io wrote:
Hello group.

I have been trying to install DVSwitch but following the document "Draft DMRGateway Install Notes", when I get to the Install and test DMRGateway part I can't go beyond point 3 as the file in point 4 does not exist.  Is there a revised document I can follow?

I also tried the 
DVSwitch-System-Builder and that also does not work.

Any complete, correct set of instructions I can find to get this set up?

Thanks in advance.


Re: Installing DVSwitch

Steve N4IRS
 

https://docs.google.com/document/d/1eN50Csr29eAprBu7eKA0Bfa2XUcsXw5iktY1Ey-Qjkg/edit

What does not work in DVSwitch-System-Builder? What are you trying to do?

Steve N4IRS

On 11/25/18 8:02 PM, Guillermo HK4KM via Groups.Io wrote:
Hello group.

I have been trying to install DVSwitch but following the document "Draft DMRGateway Install Notes", when I get to the Install and test DMRGateway part I can't go beyond point 3 as the file in point 4 does not exist.  Is there a revised document I can follow?

I also tried the 
DVSwitch-System-Builder and that also does not work.

Any complete, correct set of instructions I can find to get this set up?

Thanks in advance.


Installing DVSwitch

Guillermo HK4KM <hk4km@...>
 

Hello group.

I have been trying to install DVSwitch but following the document "Draft DMRGateway Install Notes", when I get to the Install and test DMRGateway part I can't go beyond point 3 as the file in point 4 does not exist.  Is there a revised document I can follow?

I also tried the 
DVSwitch-System-Builder and that also does not work.

Any complete, correct set of instructions I can find to get this set up?

Thanks in advance.


Re: OT: Looking for an old part

Cort N0MJS <n0mjs@...>
 

Need it by Christmas, so not a huge rush. Thanks for looking. Will let you know if I turn one up sooner.

On Nov 25, 2018, at 6:07 PM, Chris WB4ULK via Groups.Io <chood73=yahoo.com@groups.io> wrote:

If it can wait until this weekend, I may be able to help if you haven’t found it by then.

Have a bunch in storage, If I can lay hands on them.

Chris
WB4ULK

On Nov 25, 2018, at 7:01 PM, Cort N0MJS via Groups.Io <n0mjs=me.com@groups.io> wrote:

If anyone out there has a Motorola Motrac/Motran/Mocom control head & microphone, I’m looking for one. I don’t need cables or for it to even work. It’s going to be used as a prop.

--
Cort Buffington
H: +1-785-813-1501
M: +1-785-865-7206









--
Cort Buffington
H: +1-785-813-1501
M: +1-785-865-7206


Re: OT: Looking for an old part

Chris WB4ULK
 

If it can wait until this weekend, I may be able to help if you haven’t found it by then.

Have a bunch in storage, If I can lay hands on them.

Chris
WB4ULK

On Nov 25, 2018, at 7:01 PM, Cort N0MJS via Groups.Io <n0mjs=me.com@groups.io> wrote:

If anyone out there has a Motorola Motrac/Motran/Mocom control head & microphone, I’m looking for one. I don’t need cables or for it to even work. It’s going to be used as a prop.

--
Cort Buffington
H: +1-785-813-1501
M: +1-785-865-7206








OT: Looking for an old part

Cort N0MJS <n0mjs@...>
 

If anyone out there has a Motorola Motrac/Motran/Mocom control head & microphone, I’m looking for one. I don’t need cables or for it to even work. It’s going to be used as a prop.

--
Cort Buffington
H: +1-785-813-1501
M: +1-785-865-7206


Re: DStar XLX Reflector to ASL

Jeff Lehman, N8ACL
 

^ that’s the one!

 


From: main@dvswitch.groups.io on behalf of Steve N4IRS <szingman@...>
Sent: Sunday, November 25, 2018 18:52
To: main@dvswitch.groups.io
Subject: Re: [DVSwitch] DStar XLX Reflector to ASL
 
https://docs.google.com/document/d/1eN50Csr29eAprBu7eKA0Bfa2XUcsXw5iktY1Ey-Qjkg/edit

On 11/25/18 6:32 PM, Richard Hyde wrote:
Hey Jeff, Do you have a PDF how to on the setup for the ASL to C4FM  or DMR ? I can not get mine going.. Tried on a node at home and on a V-server .. 

Thanks,
             Richard Hyde
                KE4GJG
             
           London, KY 40741



On Sun, Nov 25, 2018 at 2:28 PM Jeff Lehman, KC8QCH <kc8qch@...> wrote:

I have a feeling this is an easy one. I am currently using Analog bridge and MMDVM Bridge for DMR, no sweat there (I have setup a bunch of those). I want to bring in D-Star and YSF to the system. I know that MMDVM will allow me to do that with one instance and I know that I will need multiple instances of Analog Bridge. Got that down. We have an XLX Reflector currently running and I want to bridge a service node to that reflector for our main system.

 

I’ve looked at the INI files and I think I have a rough idea of where to put things, but what do I put where? What all info do I need about the XLX Reflector to bridge it?

 

Thanks.

   Jeff

 

Jeff Lehman, KC8QCH

E-mail: kc8qch@...

Hamshack Hotline: 4218

 

Webmaster

Hamilton County ARPSC

http://www.hamcoarpsc.org

E-mail: hamcoarpsc@...

Phone: 513-452-6480

 

Allstar 47374 Administrator

World Wide Amateur Radio Guild

http://www.theguildglobal.org

E-Mail: kc8qch@...

 



Re: DStar XLX Reflector to ASL

Steve N4IRS
 

On 11/25/18 6:32 PM, Richard Hyde wrote:
Hey Jeff, Do you have a PDF how to on the setup for the ASL to C4FM  or DMR ? I can not get mine going.. Tried on a node at home and on a V-server .. 

Thanks,
             Richard Hyde
                KE4GJG
             
           London, KY 40741



On Sun, Nov 25, 2018 at 2:28 PM Jeff Lehman, KC8QCH <kc8qch@...> wrote:

I have a feeling this is an easy one. I am currently using Analog bridge and MMDVM Bridge for DMR, no sweat there (I have setup a bunch of those). I want to bring in D-Star and YSF to the system. I know that MMDVM will allow me to do that with one instance and I know that I will need multiple instances of Analog Bridge. Got that down. We have an XLX Reflector currently running and I want to bridge a service node to that reflector for our main system.

 

I’ve looked at the INI files and I think I have a rough idea of where to put things, but what do I put where? What all info do I need about the XLX Reflector to bridge it?

 

Thanks.

   Jeff

 

Jeff Lehman, KC8QCH

E-mail: kc8qch@...

Hamshack Hotline: 4218

 

Webmaster

Hamilton County ARPSC

http://www.hamcoarpsc.org

E-mail: hamcoarpsc@...

Phone: 513-452-6480

 

Allstar 47374 Administrator

World Wide Amateur Radio Guild

http://www.theguildglobal.org

E-Mail: kc8qch@...

 



Re: DStar XLX Reflector to ASL

Jeff Lehman, N8ACL
 

I just use the google doc that was provided by mike and Steve for dmr. I don’t have c4fm setup yet so. Once I figure out a it dstar that was my next project.

Jeff

 


From: main@dvswitch.groups.io on behalf of Richard Hyde <kyserver@...>
Sent: Sunday, November 25, 2018 18:33
To: main@dvswitch.groups.io
Subject: Re: [DVSwitch] DStar XLX Reflector to ASL
 
Hey Jeff, Do you have a PDF how to on the setup for the ASL to C4FM  or DMR ? I can not get mine going.. Tried on a node at home and on a V-server .. 

Thanks,
             Richard Hyde
                KE4GJG
             
           London, KY 40741



On Sun, Nov 25, 2018 at 2:28 PM Jeff Lehman, KC8QCH <kc8qch@...> wrote:

I have a feeling this is an easy one. I am currently using Analog bridge and MMDVM Bridge for DMR, no sweat there (I have setup a bunch of those). I want to bring in D-Star and YSF to the system. I know that MMDVM will allow me to do that with one instance and I know that I will need multiple instances of Analog Bridge. Got that down. We have an XLX Reflector currently running and I want to bridge a service node to that reflector for our main system.

 

I’ve looked at the INI files and I think I have a rough idea of where to put things, but what do I put where? What all info do I need about the XLX Reflector to bridge it?

 

Thanks.

   Jeff

 

Jeff Lehman, KC8QCH

E-mail: kc8qch@...

Hamshack Hotline: 4218

 

Webmaster

Hamilton County ARPSC

http://www.hamcoarpsc.org

E-mail: hamcoarpsc@...

Phone: 513-452-6480

 

Allstar 47374 Administrator

World Wide Amateur Radio Guild

http://www.theguildglobal.org

E-Mail: kc8qch@...

 


Re: DStar XLX Reflector to ASL

Richard Hyde
 

Hey Jeff, Do you have a PDF how to on the setup for the ASL to C4FM  or DMR ? I can not get mine going.. Tried on a node at home and on a V-server .. 

Thanks,
             Richard Hyde
                KE4GJG
             
           London, KY 40741



On Sun, Nov 25, 2018 at 2:28 PM Jeff Lehman, KC8QCH <kc8qch@...> wrote:

I have a feeling this is an easy one. I am currently using Analog bridge and MMDVM Bridge for DMR, no sweat there (I have setup a bunch of those). I want to bring in D-Star and YSF to the system. I know that MMDVM will allow me to do that with one instance and I know that I will need multiple instances of Analog Bridge. Got that down. We have an XLX Reflector currently running and I want to bridge a service node to that reflector for our main system.

 

I’ve looked at the INI files and I think I have a rough idea of where to put things, but what do I put where? What all info do I need about the XLX Reflector to bridge it?

 

Thanks.

   Jeff

 

Jeff Lehman, KC8QCH

E-mail: kc8qch@...

Hamshack Hotline: 4218

 

Webmaster

Hamilton County ARPSC

http://www.hamcoarpsc.org

E-mail: hamcoarpsc@...

Phone: 513-452-6480

 

Allstar 47374 Administrator

World Wide Amateur Radio Guild

http://www.theguildglobal.org

E-Mail: kc8qch@...

 


DStar XLX Reflector to ASL

Jeff Lehman, N8ACL
 

I have a feeling this is an easy one. I am currently using Analog bridge and MMDVM Bridge for DMR, no sweat there (I have setup a bunch of those). I want to bring in D-Star and YSF to the system. I know that MMDVM will allow me to do that with one instance and I know that I will need multiple instances of Analog Bridge. Got that down. We have an XLX Reflector currently running and I want to bridge a service node to that reflector for our main system.

 

I’ve looked at the INI files and I think I have a rough idea of where to put things, but what do I put where? What all info do I need about the XLX Reflector to bridge it?

 

Thanks.

   Jeff

 

Jeff Lehman, KC8QCH

E-mail: kc8qch@...

Hamshack Hotline: 4218

 

Webmaster

Hamilton County ARPSC

http://www.hamcoarpsc.org

E-mail: hamcoarpsc@...

Phone: 513-452-6480

 

Allstar 47374 Administrator

World Wide Amateur Radio Guild

http://www.theguildglobal.org

E-Mail: kc8qch@...

 


Re: Bridge Brandmeister to TGIF?

Cort N0MJS <n0mjs@...>
 

If that’s something the network operators (TGIF and BM) wanted to do, they’d probably have already done it. Cross-connecting one of the big networks to the other is a great way to get yourself into big trouble with them.

On Nov 23, 2018, at 11:09 PM, Russell, KV4S <russelljthomas@...> wrote:

Doing some brainstorming.

Can DVSwitch be used to bridge a BM TG to a TGIF TG?

Thoughts on how this can be achieved?

--
Cort Buffington
H: +1-785-813-1501
M: +1-785-865-7206






Re: Bridge Brandmeister to TGIF?

Corey Dean N3FE <n3fe@...>
 

Please don’t even attempt this.  You chose that network for a reason.

Corey n3fe

On Sat, Nov 24, 2018 at 12:09 AM Russell, KV4S <russelljthomas@...> wrote:
Doing some brainstorming.

Can DVSwitch be used to bridge a BM TG to a TGIF TG?

Thoughts on how this can be achieved?

7121 - 7140 of 9595