Date   

Re: YSFReflector to Allstarlink

Steve N4IRS
 

How are you running the programs? How are you starting and stopping programs?

On 5/13/2020 1:50 PM, honda5603@... wrote:
Steve,

I don't know how to show the output of these items:
ps ax | grep opt
netstat -unap | grep 351


Re: YSFReflector to Allstarlink

honda5603@...
 

Steve,

I don't know how to show the output of these items:
ps ax | grep opt
netstat -unap | grep 351


Re: YSFReflector to Allstarlink

Steve N4IRS
 

Stop AB and MB
Show the output of:
ps ax | grep opt
netstat -unap | grep 351

Steve

On 5/13/2020 1:08 PM, honda5603@... wrote:
GNU nano 2.7.4                      File: MMDVM_Bridge-2020-05-13.log

I: 2020-05-13 17:03:55.770 MMDVM_Bridge:
I: 2020-05-13 17:03:55.770 Portions Copyright (C) 2018 DVSwitch, INAD.
I: 2020-05-13 17:03:55.770 Hacks by Mike N4IRR and Steve N4IRS
I: 2020-05-13 17:03:55.770 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
I: 2020-05-13 17:03:55.770 This software is for use on amateur radio networks only,
I: 2020-05-13 17:03:55.770 it is to be used for educational purposes only. Its use on
I: 2020-05-13 17:03:55.770 commercial networks is strictly prohibited.
I: 2020-05-13 17:03:55.770 Copyright(C) 2015-2018 by Jonathan Naylor, G4KLX and others
M: 2020-05-13 17:03:55.770 MMDVM_Bridge-20191105_V1.4.1 is starting
M: 2020-05-13 17:03:55.770 Built 14:38:14 Nov 11 2019 (GitID #9dae1ac)
I: 2020-05-13 17:03:55.770 General Parameters
I: 2020-05-13 17:03:55.770     Callsign: KC9HTA
I: 2020-05-13 17:03:55.770     Id: 311858301
I: 2020-05-13 17:03:55.770     Duplex: no
I: 2020-05-13 17:03:55.770     Timeout: 180s
I: 2020-05-13 17:03:55.770     D-Star: disabled
I: 2020-05-13 17:03:55.770     DMR: disabled
I: 2020-05-13 17:03:55.770     YSF: enabled
I: 2020-05-13 17:03:55.770     P25: disabled
I: 2020-05-13 17:03:55.770     NXDN: disabled
I: 2020-05-13 17:03:55.770 Modem Parameters
I: 2020-05-13 17:03:55.770     Port: /dev/null
I: 2020-05-13 17:03:55.770     RX Invert: no
I: 2020-05-13 17:03:55.770     TX Invert: no
I: 2020-05-13 17:03:55.770     PTT Invert: no
I: 2020-05-13 17:03:55.770     TX Delay: 100ms
I: 2020-05-13 17:03:55.770     RX Offset: 0Hz
I: 2020-05-13 17:03:55.770     TX Offset: 0Hz
I: 2020-05-13 17:03:55.770     RX DC Offset: 0
I: 2020-05-13 17:03:55.770     TX DC Offset: 0
I: 2020-05-13 17:03:55.770     RF Level: 100.0%
I: 2020-05-13 17:03:55.770     DMR Delay: 0 (0.0ms)
I: 2020-05-13 17:03:55.770     RX Level: 50.0%
I: 2020-05-13 17:03:55.770     CW Id TX Level: 50.0%
I: 2020-05-13 17:03:55.770     D-Star TX Level: 50.0%
I: 2020-05-13 17:03:55.770     DMR TX Level: 50.0%
I: 2020-05-13 17:03:55.770     YSF TX Level: 50.0%
I: 2020-05-13 17:03:55.770     P25 TX Level: 50.0%
I: 2020-05-13 17:03:55.770     NXDN TX Level: 50.0%
I: 2020-05-13 17:03:55.770     RX Frequency: 222340000Hz (222340000Hz)
I: 2020-05-13 17:03:55.770     TX Frequency: 224940000Hz (224940000Hz)
M: 2020-05-13 17:03:55.771 Opening the MMDVM
I: 2020-05-13 17:03:55.771 Display Parameters
I: 2020-05-13 17:03:55.771     Type:
I: 2020-05-13 17:03:55.771 System Fusion Network Parameters
I: 2020-05-13 17:03:55.771     Local Address: 127.0.0.1
I: 2020-05-13 17:03:55.771     Local Port: 3200
I: 2020-05-13 17:03:55.771     Gateway Address: 192.168.1.72
I: 2020-05-13 17:03:55.771     Gateway Port: 42000
I: 2020-05-13 17:03:55.771     Mode Hang: 3s
M: 2020-05-13 17:03:55.771 Opening YSF network connection
I: 2020-05-13 17:03:55.771 RSSI
I: 2020-05-13 17:03:55.771     Mapping File: RSSI.dat
W: 2020-05-13 17:03:55.771 Cannot open the RSSI data file - RSSI.dat
I: 2020-05-13 17:03:55.771 DMR Id Lookups
I: 2020-05-13 17:03:55.771     File: /var/lib/mmdvm/DMRIds.dat
I: 2020-05-13 17:03:55.771     Reload: 24 hours
I: 2020-05-13 17:03:56.091 Loaded 164254 Ids to the DMR callsign lookup table
I: 2020-05-13 17:03:56.091 YSF RF Parameters
I: 2020-05-13 17:03:56.091     Low Deviation: no
I: 2020-05-13 17:03:56.091     Remote Gateway: no
I: 2020-05-13 17:03:56.091     Self Only: no
I: 2020-05-13 17:03:56.091     DSQ: no
I: 2020-05-13 17:03:56.091     Mode Hang: 10s
M: 2020-05-13 17:03:56.091 YSF, Opening INI file: DVSwitch.ini
I: 2020-05-13 17:03:56.091 Started the DMR Id lookup reload thread
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] TXPort -> 35100
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] RXPort -> 35103
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] FallbackID -> 1234567
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] ExportTG -> 1234
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] Slot -> 2
M: 2020-05-13 17:03:56.091 YSF, Transmitting on 127.0.0.1:35100 and listening on port 35103.  Result =$
M: 2020-05-13 17:03:56.091 MMDVM_Bridge-20191105_V1.4.1 is running
E: 2020-05-13 17:04:01.093 Error returned from sendto, err: 22
E: 2020-05-13 17:04:06.098 Error returned from sendto, err: 22
E: 2020-05-13 17:04:11.101 Error returned from sendto, err: 22
E: 2020-05-13 17:04:16.102 Error returned from sendto, err: 22
E: 2020-05-13 17:04:21.105 Error returned from sendto, err: 22
E: 2020-05-13 17:04:26.107 Error returned from sendto, err: 22
E: 2020-05-13 17:04:31.111 Error returned from sendto, err: 22
E: 2020-05-13 17:04:36.114 Error returned from sendto, err: 22
E: 2020-05-13 17:04:41.114 Error returned from sendto, err: 22
E: 2020-05-13 17:04:46.117 Error returned from sendto, err: 22
E: 2020-05-13 17:04:51.123 Error returned from sendto, err: 22
E: 2020-05-13 17:04:56.125 Error returned from sendto, err: 22
E: 2020-05-13 17:05:01.128 Error returned from sendto, err: 22
E: 2020-05-13 17:05:06.131 Error returned from sendto, err: 22
E: 2020-05-13 17:05:11.131 Error returned from sendto, err: 22
E: 2020-05-13 17:05:16.133 Error returned from sendto, err: 22
E: 2020-05-13 17:05:21.136 Error returned from sendto, err: 22
E: 2020-05-13 17:05:26.140 Error returned from sendto, err: 22
E: 2020-05-13 17:05:31.145 Error returned from sendto, err: 22
E: 2020-05-13 17:05:36.147 Error returned from sendto, err: 22
E: 2020-05-13 17:05:41.150 Error returned from sendto, err: 22
E: 2020-05-13 17:05:46.154 Error returned from sendto, err: 22
E: 2020-05-13 17:05:51.154 Error returned from sendto, err: 22
E: 2020-05-13 17:05:56.157 Error returned from sendto, err: 22
E: 2020-05-13 17:06:01.159 Error returned from sendto, err: 22
E: 2020-05-13 17:06:06.159 Error returned from sendto, err: 22
E: 2020-05-13 17:06:11.164 Error returned from sendto, err: 22
E: 2020-05-13 17:06:16.166 Error returned from sendto, err: 22
E: 2020-05-13 17:06:21.172 Error returned from sendto, err: 22
E: 2020-05-13 17:06:26.172 Error returned from sendto, err: 22


Analog Bridge:

root@nwr-asl:/opt/Analog_Bridge# ./Analog_Bridge Analog_Bridge.ini
I: 2020-05-13 17:08:18.783 Analog_Bridge Version 1.4.2 Fri Jan 10 09:38:27 EST 2020
I: 2020-05-13 17:08:18.783 Copyright (C) 2018 DVSwitch, INAD.
I: 2020-05-13 17:08:18.784 Created by Mike N4IRR and Steve N4IRS
I: 2020-05-13 17:08:18.784 Analog_Bridge comes with ABSOLUTELY NO WARRANTY
I: 2020-05-13 17:08:18.784
I: 2020-05-13 17:08:18.784 This software is for use on amateur radio networks only,
I: 2020-05-13 17:08:18.784 it is to be used for educational purposes only. Its use on
I: 2020-05-13 17:08:18.784 commercial networks is strictly prohibited.
I: 2020-05-13 17:08:18.784
I: 2020-05-13 17:08:18.784 Analog_Bridge is starting
M: 2020-05-13 17:08:18.784 Setting [MACROS] DMR -> /opt/Analog_Bridge/dvswitch.sh mode DMR
M: 2020-05-13 17:08:18.784 Setting [MACROS] DSTAR -> /opt/Analog_Bridge/dvswitch.sh mode DSTAR
M: 2020-05-13 17:08:18.784 Setting [MACROS] NXDN -> /opt/Analog_Bridge/dvswitch.sh mode NXDN
M: 2020-05-13 17:08:18.784 Setting [MACROS] P25 -> /opt/Analog_Bridge/dvswitch.sh mode P25
M: 2020-05-13 17:08:18.785 Setting [MACROS] YSF -> /opt/Analog_Bridge/dvswitch.sh mode YSF
M: 2020-05-13 17:08:18.785 Setting [MACROS] dbupdate -> /opt/Analog_Bridge/dvswitch.sh collectProcessPushDataFiles
M: 2020-05-13 17:08:18.785 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh
M: 2020-05-13 17:08:18.785 Setting [] include -> dvsm.macro
M: 2020-05-13 17:08:18.785 Setting [GENERAL] logLevel -> 2
M: 2020-05-13 17:08:18.785 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv
M: 2020-05-13 17:08:18.785 Setting [GENERAL] exportMetadata -> true
M: 2020-05-13 17:08:18.785 Setting [GENERAL] decoderFallBack -> true
M: 2020-05-13 17:08:18.785 Setting [GENERAL] useEmulator -> false
M: 2020-05-13 17:08:18.785 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] address -> 127.0.0.1
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] txPort -> 35103
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] rxPort -> 35100
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] ambeMode -> YSFN
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] minTxTimeMS -> 2500
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] gatewayDmrId -> 3118583
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] repeaterID -> 311858301
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] txTg -> 37921
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] txTs -> 2
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] colorCode -> 1
M: 2020-05-13 17:08:18.786 Setting [USRP] address -> 127.0.0.1
M: 2020-05-13 17:08:18.786 Setting [USRP] txPort -> 35103
M: 2020-05-13 17:08:18.786 Setting [USRP] rxPort -> 33510
M: 2020-05-13 17:08:18.786 Setting [USRP] usrpAudio -> AUDIO_UNITY
M: 2020-05-13 17:08:18.786 Setting [USRP] usrpGain -> 1.10
M: 2020-05-13 17:08:18.786 Setting [USRP] tlvAudio -> AUDIO_UNITY
M: 2020-05-13 17:08:18.786 Setting [USRP] tlvGain -> 0.35
M: 2020-05-13 17:08:18.786 Setting [DV3000] address -> 127.0.0.1
M: 2020-05-13 17:08:18.786 Setting [DV3000] rxPort -> 2460
I: 2020-05-13 17:08:18.786 Open UDP listener on 127.0.0.1:35100
I: 2020-05-13 17:08:18.787 Open USRP on 127.0.0.1:35103
M: 2020-05-13 17:08:18.787 Connecting to DV3000 hardware......
W: 2020-05-13 17:08:19.796 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2020-05-13 17:08:19.868 Subscriber IDs loaded: 93908
I: 2020-05-13 17:08:19.868 Default extended metadata <KC9HTA>
W: 2020-05-13 17:08:19.868 Using software MBE decoder version 1.2.3
W: 2020-05-13 17:08:19.868 Using software OP25 IMBE/AMBE vocoder
I: 2020-05-13 17:08:19.868 Connected to USRP 127.0.0.1:35103
I: 2020-05-13 17:08:19.868 Starting TLV --> Analog_Bridge (decoder) --> USRP thread
I: 2020-05-13 17:08:19.869 Starting USRP --> Analog_Bridge (encoder) -> TLV thread


Re: YSFReflector to Allstarlink

Pete Fierro
 

Using the bridge to YSF,do u have to change the TG in Analog_Bridge.ini like u do for DMR?


On Wed, May 13, 2020 at 13:09, honda5603@...
<honda5603@...> wrote:
GNU nano 2.7.4                      File: MMDVM_Bridge-2020-05-13.log

I: 2020-05-13 17:03:55.770 MMDVM_Bridge:
I: 2020-05-13 17:03:55.770 Portions Copyright (C) 2018 DVSwitch, INAD.
I: 2020-05-13 17:03:55.770 Hacks by Mike N4IRR and Steve N4IRS
I: 2020-05-13 17:03:55.770 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
I: 2020-05-13 17:03:55.770 This software is for use on amateur radio networks only,
I: 2020-05-13 17:03:55.770 it is to be used for educational purposes only. Its use on
I: 2020-05-13 17:03:55.770 commercial networks is strictly prohibited.
I: 2020-05-13 17:03:55.770 Copyright(C) 2015-2018 by Jonathan Naylor, G4KLX and others
M: 2020-05-13 17:03:55.770 MMDVM_Bridge-20191105_V1.4.1 is starting
M: 2020-05-13 17:03:55.770 Built 14:38:14 Nov 11 2019 (GitID #9dae1ac)
I: 2020-05-13 17:03:55.770 General Parameters
I: 2020-05-13 17:03:55.770     Callsign: KC9HTA
I: 2020-05-13 17:03:55.770     Id: 311858301
I: 2020-05-13 17:03:55.770     Duplex: no
I: 2020-05-13 17:03:55.770     Timeout: 180s
I: 2020-05-13 17:03:55.770     D-Star: disabled
I: 2020-05-13 17:03:55.770     DMR: disabled
I: 2020-05-13 17:03:55.770     YSF: enabled
I: 2020-05-13 17:03:55.770     P25: disabled
I: 2020-05-13 17:03:55.770     NXDN: disabled
I: 2020-05-13 17:03:55.770 Modem Parameters
I: 2020-05-13 17:03:55.770     Port: /dev/null
I: 2020-05-13 17:03:55.770     RX Invert: no
I: 2020-05-13 17:03:55.770     TX Invert: no
I: 2020-05-13 17:03:55.770     PTT Invert: no
I: 2020-05-13 17:03:55.770     TX Delay: 100ms
I: 2020-05-13 17:03:55.770     RX Offset: 0Hz
I: 2020-05-13 17:03:55.770     TX Offset: 0Hz
I: 2020-05-13 17:03:55.770     RX DC Offset: 0
I: 2020-05-13 17:03:55.770     TX DC Offset: 0
I: 2020-05-13 17:03:55.770     RF Level: 100.0%
I: 2020-05-13 17:03:55.770     DMR Delay: 0 (0.0ms)
I: 2020-05-13 17:03:55.770     RX Level: 50.0%
I: 2020-05-13 17:03:55.770     CW Id TX Level: 50.0%
I: 2020-05-13 17:03:55.770     D-Star TX Level: 50.0%
I: 2020-05-13 17:03:55.770     DMR TX Level: 50.0%
I: 2020-05-13 17:03:55.770     YSF TX Level: 50.0%
I: 2020-05-13 17:03:55.770     P25 TX Level: 50.0%
I: 2020-05-13 17:03:55.770     NXDN TX Level: 50.0%
I: 2020-05-13 17:03:55.770     RX Frequency: 222340000Hz (222340000Hz)
I: 2020-05-13 17:03:55.770     TX Frequency: 224940000Hz (224940000Hz)
M: 2020-05-13 17:03:55.771 Opening the MMDVM
I: 2020-05-13 17:03:55.771 Display Parameters
I: 2020-05-13 17:03:55.771     Type:
I: 2020-05-13 17:03:55.771 System Fusion Network Parameters
I: 2020-05-13 17:03:55.771     Local Address: 127.0.0.1
I: 2020-05-13 17:03:55.771     Local Port: 3200
I: 2020-05-13 17:03:55.771     Gateway Address: 192.168.1.72
I: 2020-05-13 17:03:55.771     Gateway Port: 42000
I: 2020-05-13 17:03:55.771     Mode Hang: 3s
M: 2020-05-13 17:03:55.771 Opening YSF network connection
I: 2020-05-13 17:03:55.771 RSSI
I: 2020-05-13 17:03:55.771     Mapping File: RSSI.dat
W: 2020-05-13 17:03:55.771 Cannot open the RSSI data file - RSSI.dat
I: 2020-05-13 17:03:55.771 DMR Id Lookups
I: 2020-05-13 17:03:55.771     File: /var/lib/mmdvm/DMRIds.dat
I: 2020-05-13 17:03:55.771     Reload: 24 hours
I: 2020-05-13 17:03:56.091 Loaded 164254 Ids to the DMR callsign lookup table
I: 2020-05-13 17:03:56.091 YSF RF Parameters
I: 2020-05-13 17:03:56.091     Low Deviation: no
I: 2020-05-13 17:03:56.091     Remote Gateway: no
I: 2020-05-13 17:03:56.091     Self Only: no
I: 2020-05-13 17:03:56.091     DSQ: no
I: 2020-05-13 17:03:56.091     Mode Hang: 10s
M: 2020-05-13 17:03:56.091 YSF, Opening INI file: DVSwitch.ini
I: 2020-05-13 17:03:56.091 Started the DMR Id lookup reload thread
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] TXPort -> 35100
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] RXPort -> 35103
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] FallbackID -> 1234567
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] ExportTG -> 1234
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] Slot -> 2
M: 2020-05-13 17:03:56.091 YSF, Transmitting on 127.0.0.1:35100 and listening on port 35103.  Result =$
M: 2020-05-13 17:03:56.091 MMDVM_Bridge-20191105_V1.4.1 is running
E: 2020-05-13 17:04:01.093 Error returned from sendto, err: 22
E: 2020-05-13 17:04:06.098 Error returned from sendto, err: 22
E: 2020-05-13 17:04:11.101 Error returned from sendto, err: 22
E: 2020-05-13 17:04:16.102 Error returned from sendto, err: 22
E: 2020-05-13 17:04:21.105 Error returned from sendto, err: 22
E: 2020-05-13 17:04:26.107 Error returned from sendto, err: 22
E: 2020-05-13 17:04:31.111 Error returned from sendto, err: 22
E: 2020-05-13 17:04:36.114 Error returned from sendto, err: 22
E: 2020-05-13 17:04:41.114 Error returned from sendto, err: 22
E: 2020-05-13 17:04:46.117 Error returned from sendto, err: 22
E: 2020-05-13 17:04:51.123 Error returned from sendto, err: 22
E: 2020-05-13 17:04:56.125 Error returned from sendto, err: 22
E: 2020-05-13 17:05:01.128 Error returned from sendto, err: 22
E: 2020-05-13 17:05:06.131 Error returned from sendto, err: 22
E: 2020-05-13 17:05:11.131 Error returned from sendto, err: 22
E: 2020-05-13 17:05:16.133 Error returned from sendto, err: 22
E: 2020-05-13 17:05:21.136 Error returned from sendto, err: 22
E: 2020-05-13 17:05:26.140 Error returned from sendto, err: 22
E: 2020-05-13 17:05:31.145 Error returned from sendto, err: 22
E: 2020-05-13 17:05:36.147 Error returned from sendto, err: 22
E: 2020-05-13 17:05:41.150 Error returned from sendto, err: 22
E: 2020-05-13 17:05:46.154 Error returned from sendto, err: 22
E: 2020-05-13 17:05:51.154 Error returned from sendto, err: 22
E: 2020-05-13 17:05:56.157 Error returned from sendto, err: 22
E: 2020-05-13 17:06:01.159 Error returned from sendto, err: 22
E: 2020-05-13 17:06:06.159 Error returned from sendto, err: 22
E: 2020-05-13 17:06:11.164 Error returned from sendto, err: 22
E: 2020-05-13 17:06:16.166 Error returned from sendto, err: 22
E: 2020-05-13 17:06:21.172 Error returned from sendto, err: 22
E: 2020-05-13 17:06:26.172 Error returned from sendto, err: 22


Analog Bridge:

root@nwr-asl:/opt/Analog_Bridge# ./Analog_Bridge Analog_Bridge.ini
I: 2020-05-13 17:08:18.783 Analog_Bridge Version 1.4.2 Fri Jan 10 09:38:27 EST 2020
I: 2020-05-13 17:08:18.783 Copyright (C) 2018 DVSwitch, INAD.
I: 2020-05-13 17:08:18.784 Created by Mike N4IRR and Steve N4IRS
I: 2020-05-13 17:08:18.784 Analog_Bridge comes with ABSOLUTELY NO WARRANTY
I: 2020-05-13 17:08:18.784
I: 2020-05-13 17:08:18.784 This software is for use on amateur radio networks only,
I: 2020-05-13 17:08:18.784 it is to be used for educational purposes only. Its use on
I: 2020-05-13 17:08:18.784 commercial networks is strictly prohibited.
I: 2020-05-13 17:08:18.784
I: 2020-05-13 17:08:18.784 Analog_Bridge is starting
M: 2020-05-13 17:08:18.784 Setting [MACROS] DMR -> /opt/Analog_Bridge/dvswitch.sh mode DMR
M: 2020-05-13 17:08:18.784 Setting [MACROS] DSTAR -> /opt/Analog_Bridge/dvswitch.sh mode DSTAR
M: 2020-05-13 17:08:18.784 Setting [MACROS] NXDN -> /opt/Analog_Bridge/dvswitch.sh mode NXDN
M: 2020-05-13 17:08:18.784 Setting [MACROS] P25 -> /opt/Analog_Bridge/dvswitch.sh mode P25
M: 2020-05-13 17:08:18.785 Setting [MACROS] YSF -> /opt/Analog_Bridge/dvswitch.sh mode YSF
M: 2020-05-13 17:08:18.785 Setting [MACROS] dbupdate -> /opt/Analog_Bridge/dvswitch.sh collectProcessPushDataFiles
M: 2020-05-13 17:08:18.785 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh
M: 2020-05-13 17:08:18.785 Setting [] include -> dvsm.macro
M: 2020-05-13 17:08:18.785 Setting [GENERAL] logLevel -> 2
M: 2020-05-13 17:08:18.785 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv
M: 2020-05-13 17:08:18.785 Setting [GENERAL] exportMetadata -> true
M: 2020-05-13 17:08:18.785 Setting [GENERAL] decoderFallBack -> true
M: 2020-05-13 17:08:18.785 Setting [GENERAL] useEmulator -> false
M: 2020-05-13 17:08:18.785 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] address -> 127.0.0.1
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] txPort -> 35103
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] rxPort -> 35100
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] ambeMode -> YSFN
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] minTxTimeMS -> 2500
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] gatewayDmrId -> 3118583
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] repeaterID -> 311858301
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] txTg -> 37921
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] txTs -> 2
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] colorCode -> 1
M: 2020-05-13 17:08:18.786 Setting [USRP] address -> 127.0.0.1
M: 2020-05-13 17:08:18.786 Setting [USRP] txPort -> 35103
M: 2020-05-13 17:08:18.786 Setting [USRP] rxPort -> 33510
M: 2020-05-13 17:08:18.786 Setting [USRP] usrpAudio -> AUDIO_UNITY
M: 2020-05-13 17:08:18.786 Setting [USRP] usrpGain -> 1.10
M: 2020-05-13 17:08:18.786 Setting [USRP] tlvAudio -> AUDIO_UNITY
M: 2020-05-13 17:08:18.786 Setting [USRP] tlvGain -> 0.35
M: 2020-05-13 17:08:18.786 Setting [DV3000] address -> 127.0.0.1
M: 2020-05-13 17:08:18.786 Setting [DV3000] rxPort -> 2460
I: 2020-05-13 17:08:18.786 Open UDP listener on 127.0.0.1:35100
I: 2020-05-13 17:08:18.787 Open USRP on 127.0.0.1:35103
M: 2020-05-13 17:08:18.787 Connecting to DV3000 hardware......
W: 2020-05-13 17:08:19.796 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2020-05-13 17:08:19.868 Subscriber IDs loaded: 93908
I: 2020-05-13 17:08:19.868 Default extended metadata <KC9HTA>
W: 2020-05-13 17:08:19.868 Using software MBE decoder version 1.2.3
W: 2020-05-13 17:08:19.868 Using software OP25 IMBE/AMBE vocoder
I: 2020-05-13 17:08:19.868 Connected to USRP 127.0.0.1:35103
I: 2020-05-13 17:08:19.868 Starting TLV --> Analog_Bridge (decoder) --> USRP thread
I: 2020-05-13 17:08:19.869 Starting USRP --> Analog_Bridge (encoder) -> TLV thread


Re: YSFReflector to Allstarlink

honda5603@...
 

GNU nano 2.7.4                      File: MMDVM_Bridge-2020-05-13.log

I: 2020-05-13 17:03:55.770 MMDVM_Bridge:
I: 2020-05-13 17:03:55.770 Portions Copyright (C) 2018 DVSwitch, INAD.
I: 2020-05-13 17:03:55.770 Hacks by Mike N4IRR and Steve N4IRS
I: 2020-05-13 17:03:55.770 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
I: 2020-05-13 17:03:55.770 This software is for use on amateur radio networks only,
I: 2020-05-13 17:03:55.770 it is to be used for educational purposes only. Its use on
I: 2020-05-13 17:03:55.770 commercial networks is strictly prohibited.
I: 2020-05-13 17:03:55.770 Copyright(C) 2015-2018 by Jonathan Naylor, G4KLX and others
M: 2020-05-13 17:03:55.770 MMDVM_Bridge-20191105_V1.4.1 is starting
M: 2020-05-13 17:03:55.770 Built 14:38:14 Nov 11 2019 (GitID #9dae1ac)
I: 2020-05-13 17:03:55.770 General Parameters
I: 2020-05-13 17:03:55.770     Callsign: KC9HTA
I: 2020-05-13 17:03:55.770     Id: 311858301
I: 2020-05-13 17:03:55.770     Duplex: no
I: 2020-05-13 17:03:55.770     Timeout: 180s
I: 2020-05-13 17:03:55.770     D-Star: disabled
I: 2020-05-13 17:03:55.770     DMR: disabled
I: 2020-05-13 17:03:55.770     YSF: enabled
I: 2020-05-13 17:03:55.770     P25: disabled
I: 2020-05-13 17:03:55.770     NXDN: disabled
I: 2020-05-13 17:03:55.770 Modem Parameters
I: 2020-05-13 17:03:55.770     Port: /dev/null
I: 2020-05-13 17:03:55.770     RX Invert: no
I: 2020-05-13 17:03:55.770     TX Invert: no
I: 2020-05-13 17:03:55.770     PTT Invert: no
I: 2020-05-13 17:03:55.770     TX Delay: 100ms
I: 2020-05-13 17:03:55.770     RX Offset: 0Hz
I: 2020-05-13 17:03:55.770     TX Offset: 0Hz
I: 2020-05-13 17:03:55.770     RX DC Offset: 0
I: 2020-05-13 17:03:55.770     TX DC Offset: 0
I: 2020-05-13 17:03:55.770     RF Level: 100.0%
I: 2020-05-13 17:03:55.770     DMR Delay: 0 (0.0ms)
I: 2020-05-13 17:03:55.770     RX Level: 50.0%
I: 2020-05-13 17:03:55.770     CW Id TX Level: 50.0%
I: 2020-05-13 17:03:55.770     D-Star TX Level: 50.0%
I: 2020-05-13 17:03:55.770     DMR TX Level: 50.0%
I: 2020-05-13 17:03:55.770     YSF TX Level: 50.0%
I: 2020-05-13 17:03:55.770     P25 TX Level: 50.0%
I: 2020-05-13 17:03:55.770     NXDN TX Level: 50.0%
I: 2020-05-13 17:03:55.770     RX Frequency: 222340000Hz (222340000Hz)
I: 2020-05-13 17:03:55.770     TX Frequency: 224940000Hz (224940000Hz)
M: 2020-05-13 17:03:55.771 Opening the MMDVM
I: 2020-05-13 17:03:55.771 Display Parameters
I: 2020-05-13 17:03:55.771     Type:
I: 2020-05-13 17:03:55.771 System Fusion Network Parameters
I: 2020-05-13 17:03:55.771     Local Address: 127.0.0.1
I: 2020-05-13 17:03:55.771     Local Port: 3200
I: 2020-05-13 17:03:55.771     Gateway Address: 192.168.1.72
I: 2020-05-13 17:03:55.771     Gateway Port: 42000
I: 2020-05-13 17:03:55.771     Mode Hang: 3s
M: 2020-05-13 17:03:55.771 Opening YSF network connection
I: 2020-05-13 17:03:55.771 RSSI
I: 2020-05-13 17:03:55.771     Mapping File: RSSI.dat
W: 2020-05-13 17:03:55.771 Cannot open the RSSI data file - RSSI.dat
I: 2020-05-13 17:03:55.771 DMR Id Lookups
I: 2020-05-13 17:03:55.771     File: /var/lib/mmdvm/DMRIds.dat
I: 2020-05-13 17:03:55.771     Reload: 24 hours
I: 2020-05-13 17:03:56.091 Loaded 164254 Ids to the DMR callsign lookup table
I: 2020-05-13 17:03:56.091 YSF RF Parameters
I: 2020-05-13 17:03:56.091     Low Deviation: no
I: 2020-05-13 17:03:56.091     Remote Gateway: no
I: 2020-05-13 17:03:56.091     Self Only: no
I: 2020-05-13 17:03:56.091     DSQ: no
I: 2020-05-13 17:03:56.091     Mode Hang: 10s
M: 2020-05-13 17:03:56.091 YSF, Opening INI file: DVSwitch.ini
I: 2020-05-13 17:03:56.091 Started the DMR Id lookup reload thread
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] TXPort -> 35100
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] RXPort -> 35103
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] FallbackID -> 1234567
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] ExportTG -> 1234
M: 2020-05-13 17:03:56.091 YSF, Setting [YSF] Slot -> 2
M: 2020-05-13 17:03:56.091 YSF, Transmitting on 127.0.0.1:35100 and listening on port 35103.  Result =$
M: 2020-05-13 17:03:56.091 MMDVM_Bridge-20191105_V1.4.1 is running
E: 2020-05-13 17:04:01.093 Error returned from sendto, err: 22
E: 2020-05-13 17:04:06.098 Error returned from sendto, err: 22
E: 2020-05-13 17:04:11.101 Error returned from sendto, err: 22
E: 2020-05-13 17:04:16.102 Error returned from sendto, err: 22
E: 2020-05-13 17:04:21.105 Error returned from sendto, err: 22
E: 2020-05-13 17:04:26.107 Error returned from sendto, err: 22
E: 2020-05-13 17:04:31.111 Error returned from sendto, err: 22
E: 2020-05-13 17:04:36.114 Error returned from sendto, err: 22
E: 2020-05-13 17:04:41.114 Error returned from sendto, err: 22
E: 2020-05-13 17:04:46.117 Error returned from sendto, err: 22
E: 2020-05-13 17:04:51.123 Error returned from sendto, err: 22
E: 2020-05-13 17:04:56.125 Error returned from sendto, err: 22
E: 2020-05-13 17:05:01.128 Error returned from sendto, err: 22
E: 2020-05-13 17:05:06.131 Error returned from sendto, err: 22
E: 2020-05-13 17:05:11.131 Error returned from sendto, err: 22
E: 2020-05-13 17:05:16.133 Error returned from sendto, err: 22
E: 2020-05-13 17:05:21.136 Error returned from sendto, err: 22
E: 2020-05-13 17:05:26.140 Error returned from sendto, err: 22
E: 2020-05-13 17:05:31.145 Error returned from sendto, err: 22
E: 2020-05-13 17:05:36.147 Error returned from sendto, err: 22
E: 2020-05-13 17:05:41.150 Error returned from sendto, err: 22
E: 2020-05-13 17:05:46.154 Error returned from sendto, err: 22
E: 2020-05-13 17:05:51.154 Error returned from sendto, err: 22
E: 2020-05-13 17:05:56.157 Error returned from sendto, err: 22
E: 2020-05-13 17:06:01.159 Error returned from sendto, err: 22
E: 2020-05-13 17:06:06.159 Error returned from sendto, err: 22
E: 2020-05-13 17:06:11.164 Error returned from sendto, err: 22
E: 2020-05-13 17:06:16.166 Error returned from sendto, err: 22
E: 2020-05-13 17:06:21.172 Error returned from sendto, err: 22
E: 2020-05-13 17:06:26.172 Error returned from sendto, err: 22


Analog Bridge:

root@nwr-asl:/opt/Analog_Bridge# ./Analog_Bridge Analog_Bridge.ini
I: 2020-05-13 17:08:18.783 Analog_Bridge Version 1.4.2 Fri Jan 10 09:38:27 EST 2020
I: 2020-05-13 17:08:18.783 Copyright (C) 2018 DVSwitch, INAD.
I: 2020-05-13 17:08:18.784 Created by Mike N4IRR and Steve N4IRS
I: 2020-05-13 17:08:18.784 Analog_Bridge comes with ABSOLUTELY NO WARRANTY
I: 2020-05-13 17:08:18.784
I: 2020-05-13 17:08:18.784 This software is for use on amateur radio networks only,
I: 2020-05-13 17:08:18.784 it is to be used for educational purposes only. Its use on
I: 2020-05-13 17:08:18.784 commercial networks is strictly prohibited.
I: 2020-05-13 17:08:18.784
I: 2020-05-13 17:08:18.784 Analog_Bridge is starting
M: 2020-05-13 17:08:18.784 Setting [MACROS] DMR -> /opt/Analog_Bridge/dvswitch.sh mode DMR
M: 2020-05-13 17:08:18.784 Setting [MACROS] DSTAR -> /opt/Analog_Bridge/dvswitch.sh mode DSTAR
M: 2020-05-13 17:08:18.784 Setting [MACROS] NXDN -> /opt/Analog_Bridge/dvswitch.sh mode NXDN
M: 2020-05-13 17:08:18.784 Setting [MACROS] P25 -> /opt/Analog_Bridge/dvswitch.sh mode P25
M: 2020-05-13 17:08:18.785 Setting [MACROS] YSF -> /opt/Analog_Bridge/dvswitch.sh mode YSF
M: 2020-05-13 17:08:18.785 Setting [MACROS] dbupdate -> /opt/Analog_Bridge/dvswitch.sh collectProcessPushDataFiles
M: 2020-05-13 17:08:18.785 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh
M: 2020-05-13 17:08:18.785 Setting [] include -> dvsm.macro
M: 2020-05-13 17:08:18.785 Setting [GENERAL] logLevel -> 2
M: 2020-05-13 17:08:18.785 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv
M: 2020-05-13 17:08:18.785 Setting [GENERAL] exportMetadata -> true
M: 2020-05-13 17:08:18.785 Setting [GENERAL] decoderFallBack -> true
M: 2020-05-13 17:08:18.785 Setting [GENERAL] useEmulator -> false
M: 2020-05-13 17:08:18.785 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] address -> 127.0.0.1
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] txPort -> 35103
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] rxPort -> 35100
M: 2020-05-13 17:08:18.785 Setting [AMBE_AUDIO] ambeMode -> YSFN
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] minTxTimeMS -> 2500
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] gatewayDmrId -> 3118583
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] repeaterID -> 311858301
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] txTg -> 37921
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] txTs -> 2
M: 2020-05-13 17:08:18.786 Setting [AMBE_AUDIO] colorCode -> 1
M: 2020-05-13 17:08:18.786 Setting [USRP] address -> 127.0.0.1
M: 2020-05-13 17:08:18.786 Setting [USRP] txPort -> 35103
M: 2020-05-13 17:08:18.786 Setting [USRP] rxPort -> 33510
M: 2020-05-13 17:08:18.786 Setting [USRP] usrpAudio -> AUDIO_UNITY
M: 2020-05-13 17:08:18.786 Setting [USRP] usrpGain -> 1.10
M: 2020-05-13 17:08:18.786 Setting [USRP] tlvAudio -> AUDIO_UNITY
M: 2020-05-13 17:08:18.786 Setting [USRP] tlvGain -> 0.35
M: 2020-05-13 17:08:18.786 Setting [DV3000] address -> 127.0.0.1
M: 2020-05-13 17:08:18.786 Setting [DV3000] rxPort -> 2460
I: 2020-05-13 17:08:18.786 Open UDP listener on 127.0.0.1:35100
I: 2020-05-13 17:08:18.787 Open USRP on 127.0.0.1:35103
M: 2020-05-13 17:08:18.787 Connecting to DV3000 hardware......
W: 2020-05-13 17:08:19.796 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2020-05-13 17:08:19.868 Subscriber IDs loaded: 93908
I: 2020-05-13 17:08:19.868 Default extended metadata <KC9HTA>
W: 2020-05-13 17:08:19.868 Using software MBE decoder version 1.2.3
W: 2020-05-13 17:08:19.868 Using software OP25 IMBE/AMBE vocoder
I: 2020-05-13 17:08:19.868 Connected to USRP 127.0.0.1:35103
I: 2020-05-13 17:08:19.868 Starting TLV --> Analog_Bridge (decoder) --> USRP thread
I: 2020-05-13 17:08:19.869 Starting USRP --> Analog_Bridge (encoder) -> TLV thread


Re: YSFReflector to Allstarlink

Steve N4IRS
 

Stop AB, and MB.
delete the MB log in /var/log/mmdvm
delete the AB log in /var/log/dvswitch
show the output of ps ax | grep opt
start ab and mb
capture the MB and AB log
post them.

On 5/13/2020 12:26 PM, honda5603@... wrote:
I: 2020-05-13 16:21:21.769 System Fusion Network Parameters
I: 2020-05-13 16:21:21.769     Local Address: 127.0.0.1
I: 2020-05-13 16:21:21.769     Local Port: 3200
I: 2020-05-13 16:21:21.769     Gateway Address: russell9.com
I: 2020-05-13 16:21:21.769     Gateway Port: 42000
I: 2020-05-13 16:21:21.769     Mode Hang: 3s
M: 2020-05-13 16:21:21.847 Opening YSF network connection
I: 2020-05-13 16:21:21.847 RSSI
I: 2020-05-13 16:21:21.847     Mapping File: RSSI.dat
W: 2020-05-13 16:21:21.847 Cannot open the RSSI data file - RSSI.dat
I: 2020-05-13 16:21:21.847 DMR Id Lookups
I: 2020-05-13 16:21:21.848     File: /var/lib/mmdvm/DMRIds.dat
I: 2020-05-13 16:21:21.848     Reload: 24 hours
I: 2020-05-13 16:21:21.992 Loaded 164254 Ids to the DMR callsign lookup ta$
I: 2020-05-13 16:21:21.992 YSF RF Parameters
I: 2020-05-13 16:21:21.992     Low Deviation: no
I: 2020-05-13 16:21:21.992     Remote Gateway: no
I: 2020-05-13 16:21:21.992     Self Only: no
I: 2020-05-13 16:21:21.992     DSQ: no
I: 2020-05-13 16:21:21.992     Mode Hang: 10s
M: 2020-05-13 16:21:21.992 YSF, Opening INI file: DVSwitch.ini
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] TXPort -> 35100
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] RXPort -> 35103
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] FallbackID -> 1234567
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] ExportTG -> 1234
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] Slot -> 2
E: 2020-05-13 16:21:21.993 Cannot bind the UDP address, err: 98
F: 2020-05-13 16:21:21.993 YSF, Can not open listener port 35103
E: 2020-05-13 16:21:26.714 Error returned from sendto, err: 22
E: 2020-05-13 16:21:31.716 Error returned from sendto, err: 22
E: 2020-05-13 16:21:36.716 Error returned from sendto, err: 22
E: 2020-05-13 16:21:41.719 Error returned from sendto, err: 22
E: 2020-05-13 16:21:46.720 Error returned from sendto, err: 22
E: 2020-05-13 16:21:51.722 Error returned from sendto, err: 22
E: 2020-05-13 16:21:56.723 Error returned from sendto, err: 22
E: 2020-05-13 16:22:01.726 Error returned from sendto, err: 22
E: 2020-05-13 16:22:06.727 Error returned from sendto, err: 22
E: 2020-05-13 16:22:11.731 Error returned from sendto, err: 22
E: 2020-05-13 16:22:16.735 Error returned from sendto, err: 22
E: 2020-05-13 16:22:21.735 Error returned from sendto, err: 22
E: 2020-05-13 16:22:26.738 Error returned from sendto, err: 22
E: 2020-05-13 16:22:31.740 Error returned from sendto, err: 22
E: 2020-05-13 16:23:06.768 Error returned from sendto, err: 22
E: 2020-05-13 16:23:11.770 Error returned from sendto, err: 22
E: 2020-05-13 16:23:16.770 Error returned from sendto, err: 22
E: 2020-05-13 16:23:21.773 Error returned from sendto, err: 22
E: 2020-05-13 16:23:26.777 Error returned from sendto, err: 22
W: 2020-05-13 16:23:29.425 YSF, TLV length does not match UDP/serial bytes$
E: 2020-05-13 16:23:29.425 YSF, Unknown tag (85) in TLV
E: 2020-05-13 16:23:31.782 Error returned from sendto, err: 22
E: 2020-05-13 16:23:36.785 Error returned from sendto, err: 22
E: 2020-05-13 16:23:41.787 Error returned from sendto, err: 22
E: 2020-05-13 16:23:46.790 Error returned from sendto, err: 22
E: 2020-05-13 16:23:51.791 Error returned from sendto, err: 22
E: 2020-05-13 16:23:56.792 Error returned from sendto, err: 22
E: 2020-05-13 16:24:01.796 Error returned from sendto, err: 22
E: 2020-05-13 16:24:06.801 Error returned from sendto, err: 22
E: 2020-05-13 16:24:11.805 Error returned from sendto, err: 22
E: 2020-05-13 16:24:16.807 Error returned from sendto, err: 22
E: 2020-05-13 16:24:21.810 Error returned from sendto, err: 22
E: 2020-05-13 16:24:26.813 Error returned from sendto, err: 22
E: 2020-05-13 16:24:31.815 Error returned from sendto, err: 22
E: 2020-05-13 16:24:36.818 Error returned from sendto, err: 22
E: 2020-05-13 16:24:41.819 Error returned from sendto, err: 22
E: 2020-05-13 16:24:46.819 Error returned from sendto, err: 22
E: 2020-05-13 16:24:51.820 Error returned from sendto, err: 22
E: 2020-05-13 16:24:56.822 Error returned from sendto, err: 22
E: 2020-05-13 16:25:01.824 Error returned from sendto, err: 22
E: 2020-05-13 16:25:06.824 Error returned from sendto, err: 22


Re: YSFReflector to Allstarlink

honda5603@...
 

I: 2020-05-13 16:21:21.769 System Fusion Network Parameters
I: 2020-05-13 16:21:21.769     Local Address: 127.0.0.1
I: 2020-05-13 16:21:21.769     Local Port: 3200
I: 2020-05-13 16:21:21.769     Gateway Address: russell9.com
I: 2020-05-13 16:21:21.769     Gateway Port: 42000
I: 2020-05-13 16:21:21.769     Mode Hang: 3s
M: 2020-05-13 16:21:21.847 Opening YSF network connection
I: 2020-05-13 16:21:21.847 RSSI
I: 2020-05-13 16:21:21.847     Mapping File: RSSI.dat
W: 2020-05-13 16:21:21.847 Cannot open the RSSI data file - RSSI.dat
I: 2020-05-13 16:21:21.847 DMR Id Lookups
I: 2020-05-13 16:21:21.848     File: /var/lib/mmdvm/DMRIds.dat
I: 2020-05-13 16:21:21.848     Reload: 24 hours
I: 2020-05-13 16:21:21.992 Loaded 164254 Ids to the DMR callsign lookup ta$
I: 2020-05-13 16:21:21.992 YSF RF Parameters
I: 2020-05-13 16:21:21.992     Low Deviation: no
I: 2020-05-13 16:21:21.992     Remote Gateway: no
I: 2020-05-13 16:21:21.992     Self Only: no
I: 2020-05-13 16:21:21.992     DSQ: no
I: 2020-05-13 16:21:21.992     Mode Hang: 10s
M: 2020-05-13 16:21:21.992 YSF, Opening INI file: DVSwitch.ini
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] TXPort -> 35100
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] RXPort -> 35103
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] FallbackID -> 1234567
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] ExportTG -> 1234
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] Slot -> 2
E: 2020-05-13 16:21:21.993 Cannot bind the UDP address, err: 98
F: 2020-05-13 16:21:21.993 YSF, Can not open listener port 35103
E: 2020-05-13 16:21:26.714 Error returned from sendto, err: 22
E: 2020-05-13 16:21:31.716 Error returned from sendto, err: 22
E: 2020-05-13 16:21:36.716 Error returned from sendto, err: 22
E: 2020-05-13 16:21:41.719 Error returned from sendto, err: 22
E: 2020-05-13 16:21:46.720 Error returned from sendto, err: 22
E: 2020-05-13 16:21:51.722 Error returned from sendto, err: 22
E: 2020-05-13 16:21:56.723 Error returned from sendto, err: 22
E: 2020-05-13 16:22:01.726 Error returned from sendto, err: 22
E: 2020-05-13 16:22:06.727 Error returned from sendto, err: 22
E: 2020-05-13 16:22:11.731 Error returned from sendto, err: 22
E: 2020-05-13 16:22:16.735 Error returned from sendto, err: 22
E: 2020-05-13 16:22:21.735 Error returned from sendto, err: 22
E: 2020-05-13 16:22:26.738 Error returned from sendto, err: 22
E: 2020-05-13 16:22:31.740 Error returned from sendto, err: 22
E: 2020-05-13 16:23:06.768 Error returned from sendto, err: 22
E: 2020-05-13 16:23:11.770 Error returned from sendto, err: 22
E: 2020-05-13 16:23:16.770 Error returned from sendto, err: 22
E: 2020-05-13 16:23:21.773 Error returned from sendto, err: 22
E: 2020-05-13 16:23:26.777 Error returned from sendto, err: 22
W: 2020-05-13 16:23:29.425 YSF, TLV length does not match UDP/serial bytes$
E: 2020-05-13 16:23:29.425 YSF, Unknown tag (85) in TLV
E: 2020-05-13 16:23:31.782 Error returned from sendto, err: 22
E: 2020-05-13 16:23:36.785 Error returned from sendto, err: 22
E: 2020-05-13 16:23:41.787 Error returned from sendto, err: 22
E: 2020-05-13 16:23:46.790 Error returned from sendto, err: 22
E: 2020-05-13 16:23:51.791 Error returned from sendto, err: 22
E: 2020-05-13 16:23:56.792 Error returned from sendto, err: 22
E: 2020-05-13 16:24:01.796 Error returned from sendto, err: 22
E: 2020-05-13 16:24:06.801 Error returned from sendto, err: 22
E: 2020-05-13 16:24:11.805 Error returned from sendto, err: 22
E: 2020-05-13 16:24:16.807 Error returned from sendto, err: 22
E: 2020-05-13 16:24:21.810 Error returned from sendto, err: 22
E: 2020-05-13 16:24:26.813 Error returned from sendto, err: 22
E: 2020-05-13 16:24:31.815 Error returned from sendto, err: 22
E: 2020-05-13 16:24:36.818 Error returned from sendto, err: 22
E: 2020-05-13 16:24:41.819 Error returned from sendto, err: 22
E: 2020-05-13 16:24:46.819 Error returned from sendto, err: 22
E: 2020-05-13 16:24:51.820 Error returned from sendto, err: 22
E: 2020-05-13 16:24:56.822 Error returned from sendto, err: 22
E: 2020-05-13 16:25:01.824 Error returned from sendto, err: 22
E: 2020-05-13 16:25:06.824 Error returned from sendto, err: 22


Re: YSFReflector to Allstarlink

honda5603@...
 

root@nwr-asl:/var/log# ls
alternatives.log   btmp          dvswitch    messages    syslog.2.gz  wtmp
Analog_Bridge.log  daemon.log    faillog     messages.1  syslog.3.gz
apt                daemon.log.1  installer   mmdvm       syslog.4.gz
asterisk           debug         kern.log    netcheck    syslog.5.gz
auth.log           debug.1       kern.log.1  syslog      syslog.6.gz
auth.log.1         dpkg.log      lastlog     syslog.1    syslog.7.gz
root@nwr-asl:/var/log#


I don't see a log file....hmmmm


Re: YSFReflector to Allstarlink

honda5603@...
 

I: 2020-05-13 16:21:21.992 YSF RF Parameters
I: 2020-05-13 16:21:21.992     Low Deviation: no
I: 2020-05-13 16:21:21.992     Remote Gateway: no
I: 2020-05-13 16:21:21.992     Self Only: no
I: 2020-05-13 16:21:21.992     DSQ: no
I: 2020-05-13 16:21:21.992     Mode Hang: 10s
M: 2020-05-13 16:21:21.992 YSF, Opening INI file: DVSwitch.ini
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] TXPort -> 35100
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] RXPort -> 35103
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] FallbackID -> 1234567
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] ExportTG -> 1234
M: 2020-05-13 16:21:21.993 YSF, Setting [YSF] Slot -> 2
E: 2020-05-13 16:21:21.993 Cannot bind the UDP address, err: 98
F: 2020-05-13 16:21:21.993 YSF, Can not open listener port 35103

ks only,
I: 2020-05-13 16:22:32.248 it is to be used for educational purposes only.
Its use on
I: 2020-05-13 16:22:32.248 commercial networks is strictly prohibited.
I: 2020-05-13 16:22:32.248
I: 2020-05-13 16:22:32.248 Analog_Bridge is starting
M: 2020-05-13 16:22:32.249 Setting [MACROS] DMR -> /opt/Analog_Bridge/dvswitch.sh mode DMR
M: 2020-05-13 16:22:32.249 Setting [MACROS] DSTAR -> /opt/Analog_Bridge/dvswitch.sh mode DSTAR
M: 2020-05-13 16:22:32.249 Setting [MACROS] NXDN -> /opt/Analog_Bridge/dvswitch.sh mode NXDN
M: 2020-05-13 16:22:32.249 Setting [MACROS] P25 -> /opt/Analog_Bridge/dvswitch.sh mode P25
M: 2020-05-13 16:22:32.249 Setting [MACROS] YSF -> /opt/Analog_Bridge/dvswitch.sh mode YSF
M: 2020-05-13 16:22:32.249 Setting [MACROS] dbupdate -> /opt/Analog_Bridge/dvswitch.sh collectProcessPushDataFiles
M: 2020-05-13 16:22:32.249 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh
M: 2020-05-13 16:22:32.249 Setting [] include -> dvsm.macro
M: 2020-05-13 16:22:32.249 Setting [GENERAL] logLevel -> 2
M: 2020-05-13 16:22:32.249 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv
M: 2020-05-13 16:22:32.249 Setting [GENERAL] exportMetadata -> true
M: 2020-05-13 16:22:32.249 Setting [GENERAL] decoderFallBack -> true
M: 2020-05-13 16:22:32.249 Setting [GENERAL] useEmulator -> false
M: 2020-05-13 16:22:32.250 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470
M: 2020-05-13 16:22:32.250 Setting [AMBE_AUDIO] address -> 127.0.0.1
M: 2020-05-13 16:22:32.250 Setting [AMBE_AUDIO] txPort -> 35103
M: 2020-05-13 16:22:32.250 Setting [AMBE_AUDIO] rxPort -> 35100
M: 2020-05-13 16:22:32.250 Setting [AMBE_AUDIO] ambeMode -> YSFN
M: 2020-05-13 16:22:32.250 Setting [AMBE_AUDIO] minTxTimeMS -> 2500
M: 2020-05-13 16:22:32.250 Setting [AMBE_AUDIO] gatewayDmrId -> 3118583
M: 2020-05-13 16:22:32.250 Setting [AMBE_AUDIO] repeaterID -> 311858301
M: 2020-05-13 16:22:32.250 Setting [AMBE_AUDIO] txTg -> 37921
M: 2020-05-13 16:22:32.250 Setting [AMBE_AUDIO] txTs -> 2
M: 2020-05-13 16:22:32.250 Setting [AMBE_AUDIO] colorCode -> 1
M: 2020-05-13 16:22:32.250 Setting [USRP] address -> 127.0.0.1
M: 2020-05-13 16:22:32.250 Setting [USRP] txPort -> 35103
M: 2020-05-13 16:22:32.250 Setting [USRP] rxPort -> 33510
M: 2020-05-13 16:22:32.250 Setting [USRP] usrpAudio -> AUDIO_UNITY
M: 2020-05-13 16:22:32.250 Setting [USRP] usrpGain -> 1.10
M: 2020-05-13 16:22:32.251 Setting [USRP] tlvAudio -> AUDIO_UNITY
M: 2020-05-13 16:22:32.251 Setting [USRP] tlvGain -> 0.35
M: 2020-05-13 16:22:32.251 Setting [DV3000] address -> 127.0.0.1
M: 2020-05-13 16:22:32.251 Setting [DV3000] rxPort -> 2460
I: 2020-05-13 16:22:32.251 Open UDP listener on 127.0.0.1:35100
I: 2020-05-13 16:22:32.251 Open USRP on 127.0.0.1:35103
M: 2020-05-13 16:22:32.251 Connecting to DV3000 hardware......
W: 2020-05-13 16:22:33.261 DV3000 not found at 127.0.0.1:2460
Project 25 IMBE Encoder/Decoder Fixed-Point implementation
Developed by Pavel Yazev E-mail: pyazev@...
Version 1.0 (c) Copyright 2009
This program comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it
under certain conditions; see the file ``LICENSE'' for details.
I: 2020-05-13 16:22:33.338 Subscriber IDs loaded: 93908
I: 2020-05-13 16:22:33.339 Default extended metadata <KC9HTA>
W: 2020-05-13 16:22:33.339 Using software MBE decoder version 1.2.3
W: 2020-05-13 16:22:33.339 Using software OP25 IMBE/AMBE vocoder
I: 2020-05-13 16:22:33.339 Connected to USRP 127.0.0.1:35103
I: 2020-05-13 16:22:33.339 Starting TLV --> Analog_Bridge (decoder) --> USRP thread
I: 2020-05-13 16:22:33.339 Starting USRP --> Analog_Bridge (encoder) -> TLV thread


Re: YSFReflector to Allstarlink

Steve N4IRS
 

Watch the MMDVM_ Bridge log in /var/log/mmdvm

Sent by smoke signal (AT&T)


From: main@DVSwitch.groups.io <main@DVSwitch.groups.io> on behalf of honda5603@... <honda5603@...>
Sent: Wednesday, May 13, 2020 12:19:42 PM
To: main@DVSwitch.groups.io <main@DVSwitch.groups.io>
Subject: Re: [DVSwitch] YSFReflector to Allstarlink
 
Thanks again, I changed all of these options.  I can connect my normal public node (51505) to the private node (1999), but not seeing a connection to YSFdashboard: russell9.com:1234

Is there a place to check if YSF side is indeed connecting for troubleshooting?


Re: YSFReflector to Allstarlink

honda5603@...
 

Thanks again, I changed all of these options.  I can connect my normal public node (51505) to the private node (1999), but not seeing a connection to YSFdashboard: russell9.com:1234

Is there a place to check if YSF side is indeed connecting for troubleshooting?


Re: YSFReflector to Allstarlink

Steve N4IRS
 

All looks good except in MMDVM_Bridge.ini:

[System Fusion]
Enable=0 <----------------- Enable this

[System Fusion Network]
Enable=1
LocalAddress=127.0.0.1
LocalPort=3200
GatewayAddress=ysfreflector.dvswitch.org <-------------- this is the dns entry or IP of the reflector
GatewayPort=42166 <---------- This is the port number the reflector is listening on.
Debug=0


On 5/13/2020 11:50 AM, honda5603@... wrote:
Thanks Steve again for helping me.  Here's what I was able to capture:

Here's analog bridge ini:


; Analog_Bridge configuration file.
;   This file should be placed in either /etc or it can be
;   supplied as a path on the Analog_Bridge command line.

; The best way to think of this file is that there are two main sections, the USRP (analog audi$
; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined i$
; As you might expect, the reverse direction is defined too.

; Analog_Bridge supports include files. More on this later...
include = dvsm.macro
; include = asl.macro

; General Section describes settings for Analog_Bridge itself.
[GENERAL]
logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Mess$

; Metadata management
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data
exportMetadata = true                   ; Export metadata to USRP partner (transcode setups req$

; General vocoder setup information
decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is$
useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server

; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address = 127.0.0.1                     ; IP address of xx_Bridge
txPort = 35103                          ; Transmit TLV frames to partner on this port
rxPort = 35100                          ; Listen for TLV frames from partner on this port
ambeMode = YSFN                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode $
minTxTimeMS = 2500                      ; Minimum time in MS for hang delay (0-10000)

; The metadata below is used when ASL is the source since it does not have any concept of digit$
gatewayDmrId = 3118583                  ; ID to use when transmitting from Analog_Bridge
repeaterID = 311858301                  ; ID of source repeater
txTg = 37921                          ; TG to use for all frames sent from Analog_Bridge -> xx_$
txTs = 2                                ; Slot to use for frames sent from Analog_Bridge -> xx_$
colorCode = 1                           ; Color Code to assign DMR frames

; Information for USRP channel driver.  This interface uses PCM to transfer audio information
; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog cli$
; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces bac$
; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.
;   When using ASL, this matches the rpt.conf ASL file with a setting like:
;   rxchannel = usrp/127.0.0.1:34001:32001
;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (cro$
;   each instance with its own ini file.
[USRP]
address = 127.0.0.1                     ; IP address of USRP partner (Allstar/Asterisk or anoth$
txPort = 35103                          ; Transmit USRP frames on this port
rxPort = 33510                          ; Listen for USRP frames on this port
usrpAudio = AUDIO_UNITY                 ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_G$
usrpGain = 1.10                         ; Gain (in db) of the AGC filter
tlvAudio = AUDIO_UNITY                  ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BP$
tlvGain = 0.35                          ; Gain factor of audio from ASL (0.0-1.0)

Here is the DVSwitch.ini file:



  GNU nano 2.7.4                          File: DVSwitch.ini

; MMDVM_Bridge export / import configuration file.
;   This file should be placed along side of MMDVM_Bridge or it can be
;   supplied as a path on the MMDVM_BRIDGE environment variable.

; Configure the Quantar Repeater Partner
; Note that the TX and RX ports are already reversed for MMDVM_Bridge <--> Quantar_Bridge
[QUANTAR]
logFilePath = /var/log/Quantar_Bridge.log
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 34103                  ; Port to send AMBE TLV frames to (export)
RXPort = 34100                  ; Port to listen on (import)
quantarPort = 1994              ; HDLC frames To/From the Quantar repeater
logLevel = 2                    ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=I$
debug = 0                       ; Debug 0 = off, 1 = on (adds lots of additional messages)

; Configure the DMR Partner
; Audio format is AMBE 72 bit
[DMR]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 31100                  ; Port to send AMBE TLV frames to (export)
RXPort = 31103                  ; Port to listen on (import)
Slot = 2                        ; Export slot

; Configure the D-Star Partner
; Audio format is AMBE 48 bit (DSAMBE)
[DSTAR]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 32100                  ; Port to send AMBE TLV frames to (export)
RXPort = 32103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, expor$
ExportTG = 9                    ; Which TG to export
Slot = 2                        ; Export slot

; Configure the NXDN Partner
; Audio format is AMBE 72 bit
[NXDN]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 33100                  ; Port to send AMBE TLV frames to (export)
RXPort = 33103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, expor$
NXDNFallbackID  = 12345         ; Use this ID when the input DMR ID is not found in the database
Translate = 1234=4321           ; Translate NXDN TG < -- > DMR TG (bidirectional)
Slot = 2                        ; Export slot

; Configure the P25 Partner
; Audio format is IMBE 88 bit
[P25]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 34100                  ; Port to send AMBE TLV frames to (export)
RXPort = 34103                  ; Port to listen on (import)
Slot = 2                        ; Export slot

; Configure the Yaesu Fusion Partner
; Audio format is AMBE 72 bit
; Audio format is IMBE 88 bit
[YSF]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 35100                  ; Port to send AMBE TLV frames to (export)
RXPort = 35103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, expor$
ExportTG = 1234                 ; Which TG to export
Slot = 2                        ; Export slot


And then the MMDVM_Bridge.ini:


[General]
Callsign=KC9HTA
Id=311858301
Timeout=180
Duplex=0

[Info]
RXFrequency=222340000
TXFrequency=224940000
Power=1
Latitude=41.7333
Longitude=-50.3999
Height=0
Location=Iceberg, North Atlantic
Description=MMDVM_Bridge
URL=https://groups.io/g/DVSwitch

[Log]
# Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
DisplayLevel=1
FileLevel=2
FilePath=/var/log/mmdvm
FileRoot=MMDVM_Bridge

[DMR Id Lookup]
File=/var/lib/mmdvm/DMRIds.dat
Time=24

[NXDN Id Lookup]
File=/var/lib/mmdvm/NXDN.csv
Time=24

[Modem]
Port=/dev/null
RSSIMappingFile=RSSI.dat
Trace=0
Debug=0

[D-Star]
Enable=0
Module=C

[DMR]
Enable=0
ColorCode=1
EmbeddedLCOnly=1
DumpTAData=0

[System Fusion]
Enable=0

[P25]
Enable=0
NAC=293

[NXDN]
Enable=0
RAN=1
Id=12345

[D-Star Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=20010
LocalPort=20011
Debug=0

[DMR Network]
Enable=0
Address=3108.repeater.net
Port=62031
Jitter=360
Local=62032
Password=passw0rd
# for DMR+ see https://github.com/DVSwitch/MMDVM_Bridge/blob/master/DOC/DMRplus_startup_options$
# for XLX the syntax is: Options=XLX:4009
# Options=
Slot1=0
Slot2=1
Debug=0

[System Fusion Network]
Enable=1
LocalAddress=127.0.0.1
LocalPort=3200
GatewayAddress=ysfreflector.dvswitch.org
GatewayPort=42166
Debug=0







Re: YSFReflector to Allstarlink

honda5603@...
 

Thanks Steve again for helping me.  Here's what I was able to capture:

Here's analog bridge ini:


; Analog_Bridge configuration file.
;   This file should be placed in either /etc or it can be
;   supplied as a path on the Analog_Bridge command line.

; The best way to think of this file is that there are two main sections, the USRP (analog audi$
; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined i$
; As you might expect, the reverse direction is defined too.

; Analog_Bridge supports include files. More on this later...
include = dvsm.macro
; include = asl.macro

; General Section describes settings for Analog_Bridge itself.
[GENERAL]
logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Mess$

; Metadata management
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data
exportMetadata = true                   ; Export metadata to USRP partner (transcode setups req$

; General vocoder setup information
decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is$
useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server

; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address = 127.0.0.1                     ; IP address of xx_Bridge
txPort = 35103                          ; Transmit TLV frames to partner on this port
rxPort = 35100                          ; Listen for TLV frames from partner on this port
ambeMode = YSFN                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode $
minTxTimeMS = 2500                      ; Minimum time in MS for hang delay (0-10000)

; The metadata below is used when ASL is the source since it does not have any concept of digit$
gatewayDmrId = 3118583                  ; ID to use when transmitting from Analog_Bridge
repeaterID = 311858301                  ; ID of source repeater
txTg = 37921                          ; TG to use for all frames sent from Analog_Bridge -> xx_$
txTs = 2                                ; Slot to use for frames sent from Analog_Bridge -> xx_$
colorCode = 1                           ; Color Code to assign DMR frames

; Information for USRP channel driver.  This interface uses PCM to transfer audio information
; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog cli$
; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces bac$
; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.
;   When using ASL, this matches the rpt.conf ASL file with a setting like:
;   rxchannel = usrp/127.0.0.1:34001:32001
;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (cro$
;   each instance with its own ini file.
[USRP]
address = 127.0.0.1                     ; IP address of USRP partner (Allstar/Asterisk or anoth$
txPort = 35103                          ; Transmit USRP frames on this port
rxPort = 33510                          ; Listen for USRP frames on this port
usrpAudio = AUDIO_UNITY                 ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_G$
usrpGain = 1.10                         ; Gain (in db) of the AGC filter
tlvAudio = AUDIO_UNITY                  ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BP$
tlvGain = 0.35                          ; Gain factor of audio from ASL (0.0-1.0)

Here is the DVSwitch.ini file:



  GNU nano 2.7.4                          File: DVSwitch.ini

; MMDVM_Bridge export / import configuration file.
;   This file should be placed along side of MMDVM_Bridge or it can be
;   supplied as a path on the MMDVM_BRIDGE environment variable.

; Configure the Quantar Repeater Partner
; Note that the TX and RX ports are already reversed for MMDVM_Bridge <--> Quantar_Bridge
[QUANTAR]
logFilePath = /var/log/Quantar_Bridge.log
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 34103                  ; Port to send AMBE TLV frames to (export)
RXPort = 34100                  ; Port to listen on (import)
quantarPort = 1994              ; HDLC frames To/From the Quantar repeater
logLevel = 2                    ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=I$
debug = 0                       ; Debug 0 = off, 1 = on (adds lots of additional messages)

; Configure the DMR Partner
; Audio format is AMBE 72 bit
[DMR]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 31100                  ; Port to send AMBE TLV frames to (export)
RXPort = 31103                  ; Port to listen on (import)
Slot = 2                        ; Export slot

; Configure the D-Star Partner
; Audio format is AMBE 48 bit (DSAMBE)
[DSTAR]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 32100                  ; Port to send AMBE TLV frames to (export)
RXPort = 32103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, expor$
ExportTG = 9                    ; Which TG to export
Slot = 2                        ; Export slot

; Configure the NXDN Partner
; Audio format is AMBE 72 bit
[NXDN]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 33100                  ; Port to send AMBE TLV frames to (export)
RXPort = 33103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, expor$
NXDNFallbackID  = 12345         ; Use this ID when the input DMR ID is not found in the database
Translate = 1234=4321           ; Translate NXDN TG < -- > DMR TG (bidirectional)
Slot = 2                        ; Export slot

; Configure the P25 Partner
; Audio format is IMBE 88 bit
[P25]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 34100                  ; Port to send AMBE TLV frames to (export)
RXPort = 34103                  ; Port to listen on (import)
Slot = 2                        ; Export slot

; Configure the Yaesu Fusion Partner
; Audio format is AMBE 72 bit
; Audio format is IMBE 88 bit
[YSF]
Address = 127.0.0.1             ; Address to send AMBE TLV frames to (export)
TXPort = 35100                  ; Port to send AMBE TLV frames to (export)
RXPort = 35103                  ; Port to listen on (import)
FallbackID = 1234567            ; In case we can not find a valid DMR id in the database, expor$
ExportTG = 1234                 ; Which TG to export
Slot = 2                        ; Export slot


And then the MMDVM_Bridge.ini:


[General]
Callsign=KC9HTA
Id=311858301
Timeout=180
Duplex=0

[Info]
RXFrequency=222340000
TXFrequency=224940000
Power=1
Latitude=41.7333
Longitude=-50.3999
Height=0
Location=Iceberg, North Atlantic
Description=MMDVM_Bridge
URL=https://groups.io/g/DVSwitch

[Log]
# Logging levels, 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
DisplayLevel=1
FileLevel=2
FilePath=/var/log/mmdvm
FileRoot=MMDVM_Bridge

[DMR Id Lookup]
File=/var/lib/mmdvm/DMRIds.dat
Time=24

[NXDN Id Lookup]
File=/var/lib/mmdvm/NXDN.csv
Time=24

[Modem]
Port=/dev/null
RSSIMappingFile=RSSI.dat
Trace=0
Debug=0

[D-Star]
Enable=0
Module=C

[DMR]
Enable=0
ColorCode=1
EmbeddedLCOnly=1
DumpTAData=0

[System Fusion]
Enable=0

[P25]
Enable=0
NAC=293

[NXDN]
Enable=0
RAN=1
Id=12345

[D-Star Network]
Enable=0
GatewayAddress=127.0.0.1
GatewayPort=20010
LocalPort=20011
Debug=0

[DMR Network]
Enable=0
Address=3108.repeater.net
Port=62031
Jitter=360
Local=62032
Password=passw0rd
# for DMR+ see https://github.com/DVSwitch/MMDVM_Bridge/blob/master/DOC/DMRplus_startup_options$
# for XLX the syntax is: Options=XLX:4009
# Options=
Slot1=0
Slot2=1
Debug=0

[System Fusion Network]
Enable=1
LocalAddress=127.0.0.1
LocalPort=3200
GatewayAddress=ysfreflector.dvswitch.org
GatewayPort=42166
Debug=0






Re: YSFReflector to Allstarlink

Steve N4IRS
 

Yes, enable YSF and YSF networking in MMDVM_Bridge and move Analog_Bridge.ini from DMR to YSF. Also, point Analog_Bridge.ini at the proper ports in DVSwitch.ini

On 5/13/2020 11:10 AM, honda5603@... wrote:
Thanks Steve for the information I just confirmed DMR, but need to swap everything to YSF?


Re: YSFReflector to Allstarlink

honda5603@...
 

Thanks Steve for the information I just confirmed DMR, but need to swap everything to YSF?


Re: YSFReflector to Allstarlink

Steve N4IRS
 

Follow this and change MMDVM_Bridge.ini to YSF from DMR.
<https://docs.google.com/document/d/1eN50Csr29eAprBu7eKA0Bfa2XUcsXw5iktY1Ey-Qjkg/edit>

Steve N4IRS

On 5/13/2020 10:01 AM, honda5603@... wrote:
What's the easiest way to bridge both of these together? 


YSFReflector to Allstarlink

honda5603@...
 

What's the easiest way to bridge both of these together? 


Re: Possible Loop in QSO DMR and MMDVM_Bridge or Analog_Bridge malfunction.

EA5GVK Joaquin
 

So far, so good.
We installed the new binary revision dated yesterday this morning.
I'm reporting the results to you, Steve.
Greetings and thank you for your attention.


Re: Hytera DMR Gateway

Marco IW0RED
 

Hi Nomis, sure this is the video I followed:

https://www.youtube.com/watch?v=UpYZx2bjG3s

73 Marco IW0RED.

--
Marco Brunozzi

Tel. +14152360004
Cel. +393483343274
Skype: marco.brunozzi
Twitter: marcobrunozzi
---------------------------------------


Re: Hytera DMR Gateway

Nomis Bayan Jr.
 

Hi Marco, You have mentioned that you follow a video on the hytera repeater with hytera dmr gateway. Can you please direct me as to where I can find that video. Thank you.
 73,'s N0MIS