How is the latency between your AMBEserver and the cloud VPS? I ran a setup like that for a while, where pings were only about 2/4 MS between my home internet connection and the VPS, and all was fine.

AFAIK, if you want to link Wires-X to anything, you need an RF link between YSF and Wires-X using a hotspot and a radio connected to the HRI-200 for hosting a Wires-X room. You can't connect an HRI-20

Hi: I wish to create a bridge between XLX and MMDVM, DMR all the way through, not Brandmeister. Can this be done with two instances of MMDVM_Bridge with inverted ports? If so, I don't see how to direc

I thought DMRGateway was dead... Sounds like what I need. As I understand it, HBlink3 uses quite a lot of memory, and my resources are limited, so would rather not use it for such a simple bridge if I

The second endpoint is a master server, yes, in this case, TGIF. I didn't think there was a way only using two instances of MMDVM_Bridge to direct traffic, just wanted to make sure I wasn't missing an

Hi all: For the entire time I've been using DVSwitch, I've had usrpAudio=AUDIO_USE_Gain on Analog_Bridge. I'd like to use AGC, as dynamic range from DMR can be quite wide, but I find the attack and re

Hi Mike: Very cool. Thanks for looking at this. I agree re digital modes. Also, Fusion radios tend to have some dithering built-in, or something. There always seems to be some constant low level white

Hi: Perhaps I'm missing something really obvious here, but when using MMDVM_Bridge to go between a YSF reflector and a DMR master server, how do you specify which DMR talkgroup to use? The only refere

I installed the new A_B yesterday morning, and enabled AGC. What a difference! Very smooth, and gets through analog a lot better with certain radios. Thanks for the great work.

Hi: This is nothing new, but I'm trying to figure out where it's coming from. At the start of each DMR transmission, when listening on Allstar, there is a small pop sound. I've been on some other Alls

In the example of bm tg <->MB_bm<->MB_xlx<->XLX ref how would you direct to a specific BM talkgroup? Just assume TG9 and a static talkgroup on the BM self-care page?

Unfortunately, I can’t really help, other than to ask if you are attempting this installation on Debian Buster. A friend recently ran into this, and ended up using stretch instead, because it just wor

Hi: I was just asked by someone if it was possible to pass DTMF from YSF to DMR to an Allstar node such that it can be driven remotely from MMDVM, rather than what most people want going the other way

I would’ve thought that as well, although if I Chi up on a digital radio and start sending DTMF, it sounds pretty pure on other DMR radios, as well as on the other side of MMDVM bridge. I was pretty s

Hi: I have a bridge set up using AGC with the following parameters: usrpAudio = AUDIO_USE_AGC ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC) usrpGain = 0.50 ; Gain factor when usrpAu

A few things you can do: In /etc/asterisk/rpt.conf: 1. Change the value of telemdefault. 0 = no telemetry, with the exception of initial connect failure messages, 1=on (default), 2=telemetry only for

Not in the context of DVSM, but I ran a remote AMBEserver for Analog_Bridge for a while, ran into some problems and eventually scrapped it for md380emu, since I didn't care about DStar. My DStar bridg

If you're using HamVoIP, it's much, much easier to dedicate a second Pi to DVSwitch and connect USRP between them on the LAN. I've done this, and it works well. I also have a couple of ASL 1.01 system

Analog_Bridge is only used to transcode uncommon audio formats, like DMR to P25, or DStar to YSF. DMR, NXDN and YSF use the same codec, so MMDVM_Bridge handles that with no need to translate through A

Hi: I have a system that incorporates ASL, XLX, HBLink and DVSwitch. I'm toying with the idea of adding P25. Currently, DStar is handled by XLX and a pair of transcoders connected to the XLX reflector