Disable courtesy tones and node connect/disconnects from going to DMR


Steve N4IRS
 

I have added a quick page to the wiki for the AllStarLink subgroup. The page is at <https://dvswitch.groups.io/g/allstarlink/wiki/Home> I will move it later but it's "up" for now.
The AllStarLink subgroup is available for us to discuss the specifics of connecting to ASL. <https://dvswitch.groups.io/g/allstarlink>

73, Steve N4IRS

On 5/21/2018 10:17 AM, Russell Thomas, KV4S wrote:
Is there anyway to turn these off?

from another mailing list I set this:
nounkeyct=1          ; Removes RF side courtesy tone (remotetx) - Link Side

I'm still hearing courtesy tones and node connect/disconnects on DMR.

My guess is because it's the USRP behaves different than radio?

Any ideas?


Jeff Carrier
 

set duplex to duplex=0 in your allstar node stanza for that node.

Half duplex with no telemetry tones or hang time. Special Case: Full duplex if linktolink is set to yes. This mode is preferred when interfacing with an external multiport repeater controller.

On Mon, May 21, 2018 at 8:17 AM, Russell Thomas, KV4S <russelljthomas@...> wrote:
Is there anyway to turn these off?

from another mailing list I set this:
nounkeyct=1          ; Removes RF side courtesy tone (remotetx) - Link Side

I'm still hearing courtesy tones and node connect/disconnects on DMR.

My guess is because it's the USRP behaves different than radio?

Any ideas?



Steve N4IRS
 

Russel,
Here is the suggested node settings for a USRP connection:
[1999]
rxchannel = USRP/127.0.0.1:34001:32001  ; Use the USRP channel driver. Must be enabled in modules.conf
                    ; 127.0.0.1 = IP of the target application
                    ; 34001 = UDP port the target application is listening on
                    ; 32001 = UDP port ASL is listening on

duplex = 0                ; 0 = Half duplex with no telemetry tones or hang time. Ah, but Allison STILL talks!

hangtime = 0                ; squelch tail hang time 0
althangtime = 0                ; longer squelch tail hang time 0

holdofftelem = 1            ; Hold off all telemetry when signal is present on receiver or from connected nodes
                    ; except when an ID needs to be done and there is a signal coming from a connected node.

telemdefault = 0            ; 0 = telemetry output off. Don't send Allison to DMR !!!!!!!!!!!!!!!!! Trust me.

telemdynamic = 0            ; 0 = disallow users to change the local telemetry setting with a COP command,

linktolink = no                ; disables forcing physical half-duplex operation of main repeater while
                    ; still keeping half-duplex semantics (optional)

nounkeyct = 1                ; Set to a 1 to eliminate courtesy tones and associated delays.

totime = 180000                ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

idrecording = |ie            ; id recording or morse string see http://ohnosec.org/drupal/node/87
idtalkover = |ie            ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129

Sorry about the formatting, I'll add this to the wiki and fix the formatting.

On 5/21/2018 10:17 AM, Russell Thomas, KV4S wrote:
Is there anyway to turn these off?

from another mailing list I set this:
nounkeyct=1          ; Removes RF side courtesy tone (remotetx) - Link Side

I'm still hearing courtesy tones and node connect/disconnects on DMR.

My guess is because it's the USRP behaves different than radio?

Any ideas?


 

Is there anyway to turn these off?

from another mailing list I set this:
nounkeyct=1          ; Removes RF side courtesy tone (remotetx) - Link Side

I'm still hearing courtesy tones and node connect/disconnects on DMR.

My guess is because it's the USRP behaves different than radio?

Any ideas?