Topics

Setup of a Bridge YSF to DMR - Anyone out there who can solve this mystery ? #mmdvm_bridge


Uli
 

I simply want to link my YSF Reflector to a Talkgroup on Brandmeister.

Meanwhile I have tried 4 full installation attempts to do a Bridge between YSF and DMR but no luck.
I have 2 RPI 3B+, both running raspbian stretch lite. One has a YSF Reflector installed according to QSO365´s (very good and working ) explanation. This Reflector and its Dashboard installed on the first attempt and runs fine without problems
The other RPI 3B+ also has raspbian stretch lite installed, PHP7.0 and on top of it DVSwitch-System-Builder.

Both RPi´s are running in the same Network 192.168.10.xxx behind a firewall.
I was able to get the MMDVM_Bridge Dashboard running but it does not show any links or connection attempts from HT´s and the status is always idle.
How do I get the MMDVM Bridge to link my reflector to the Brandmeister TG i have entered in DVSwitch.ini?

Is there a complete detailed description which values in MMDVM_Bridge.ini and DVSwitch.ini and possibly in any other hidden config files or somewhere else need to be changed/adapted and how?
I have done the suggested changes of values in the config files  like from this https://dvswitch.groups.io/g/main/wiki/Bridge-DMR-to-YSF-Narrow
but there are a lot of unanswered questions e.g. what do I put in "DMR adress" (I assume its the Brandmeister  Master??) or in YSF Gateway Address (is it the URL of the other Pi that runs the Reflector?)
What other ports do I need to open up on the firewall ?
How should the config files look like for my setup?
I have tried everything I could think of but no luck, the Bridge does not work as it should

Do I need anything else (Software or Hardware than the two Raspberrys to do this? Did I miss anything?
I´m completely stuck at this point.

any help would greatly be appreciated

Uli
DJ5UW


Steve N4IRS
 

Uli,
Do not worry about the Dashboard. You want to look at the MMDVM_Bridge log file. If you setup MMDVM_Bridge.ini and DVSwitch.ini as the wiki states, all you should have to do is point MMDVM_Bridge at the 2 systems you want to bridge see below:

[DMR Network]
Enable=1
Address=hblink.dvswitch.org <---------- Point this at the DMR network
Port=62031
Jitter=360
Local=62032
Password=passw0rd
Slot1=0
Slot2=1
Debug=0

[System Fusion Network]
Enable=1
LocalAddress=0
LocalPort=3200
GatewayAddress=ysfreflector.dvswitch.org <-------- point this at the YSF reflector
GatewayPort=42166 <-------- Set this to the proper port for the reflector
Debug=0


Steve, N4IRS


On 4/15/2020 4:17 AM, Uli wrote:
I simply want to link my YSF Reflector to a Talkgroup on Brandmeister.

Meanwhile I have tried 4 full installation attempts to do a Bridge between YSF and DMR but no luck.
I have 2 RPI 3B+, both running raspbian stretch lite. One has a YSF Reflector installed according to QSO365´s (very good and working ) explanation. This Reflector and its Dashboard installed on the first attempt and runs fine without problems
The other RPI 3B+ also has raspbian stretch lite installed, PHP7.0 and on top of it DVSwitch-System-Builder.

Both RPi´s are running in the same Network 192.168.10.xxx behind a firewall.
I was able to get the MMDVM_Bridge Dashboard running but it does not show any links or connection attempts from HT´s and the status is always idle.
How do I get the MMDVM Bridge to link my reflector to the Brandmeister TG i have entered in DVSwitch.ini?

Is there a complete detailed description which values in MMDVM_Bridge.ini and DVSwitch.ini and possibly in any other hidden config files or somewhere else need to be changed/adapted and how?
I have done the suggested changes of values in the config files  like from this https://dvswitch.groups.io/g/main/wiki/Bridge-DMR-to-YSF-Narrow
but there are a lot of unanswered questions e.g. what do I put in "DMR adress" (I assume its the Brandmeister  Master??) or in YSF Gateway Address (is it the URL of the other Pi that runs the Reflector?)
What other ports do I need to open up on the firewall ?
How should the config files look like for my setup?
I have tried everything I could think of but no luck, the Bridge does not work as it should

Do I need anything else (Software or Hardware than the two Raspberrys to do this? Did I miss anything?
I´m completely stuck at this point.

any help would greatly be appreciated

Uli
DJ5UW



Alec Wasserman
 

Yes double check ysf gateway port.  Everything has to match and it will work !


Tito Lopez - YN1OB
 

I have a similar setup like you except mine nodes are in the cloud on two different VPS providers. I made those changes and I see traffic on TG hoseline at BM . I also see traffic in my YSF reflector the problem is that No YSF Audio is heard on either end. DVswitch Mobile on LTE and a hotspot at home. DMR  mode on the hotspot is sweet except that YSFaudio cant be heard.


YN1OB
W3DAW

On Wed, Apr 15, 2020, 06:51 <alecwasserman@...> wrote:
Yes double check ysf gateway port.  Everything has to match and it will work !


Uli
 

Thanks everyone,
I have solved it now. The DVSwitch System Builder was the problem as it didn´t work.
I have started from scratch again and only installed the Repo and DVSwitch
Now Bridging to BM and back to YSF works fine, the sound is clear and noisefree. The Callsigns are also visble on both ends

Uli
DJ5UW


Steve N4IRS
 

It would have been nice to know what was wrong. Based on what you posted the config was correct. It would have been nice to see traffic from both ends.

Steve N4IRS

On 4/16/2020 11:26 AM, Uli wrote:
Thanks everyone,
I have solved it now. The DVSwitch System Builder was the problem as it didn´t work.
I have started from scratch again and only installed the Repo and DVSwitch
Now Bridging to BM and back to YSF works fine, the sound is clear and noisefree. The Callsigns are also visble on both ends

Uli
DJ5UW


Tito Lopez - YN1OB
 

Yep I did that just that rebuilt everything a few days ago, I still get no Audio from DMR <--->YSF Reflector. I see traffic but just that


Steve N4IRS
 

I don't know about anyone else, but it's a little hard to troubleshoot without seeing the logs.

On 4/16/2020 12:56 PM, Tito Lopez wrote:
Yep I did that just that rebuilt everything a few days ago, I still get no Audio from DMR <--->YSF Reflector. I see traffic but just that


Tito Lopez - YN1OB
 

Here is my Analog_Bridge Log


I: 2020-04-16 18:30:52.292 Analog_Bridge is starting
M: 2020-04-16 18:30:52.294 Setting [MACROS] DMR -> /opt/Analog_Bridge/dvswitch.sh mode DMR
M: 2020-04-16 18:30:52.294 Setting [MACROS] DSTAR -> /opt/Analog_Bridge/dvswitch.sh mode DSTAR
M: 2020-04-16 18:30:52.294 Setting [MACROS] NXDN -> /opt/Analog_Bridge/dvswitch.sh mode NXDN
M: 2020-04-16 18:30:52.294 Setting [MACROS] P25 -> /opt/Analog_Bridge/dvswitch.sh mode P25
M: 2020-04-16 18:30:52.294 Setting [MACROS] YSF -> /opt/Analog_Bridge/dvswitch.sh mode YSF
M: 2020-04-16 18:30:52.294 Setting [MACROS] dbupdate -> /opt/Analog_Bridge/dvswitch.sh collectProcessPushDataFiles
M: 2020-04-16 18:30:52.294 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh
M: 2020-04-16 18:30:52.294 Setting [] include -> dvsm.macro
M: 2020-04-16 18:30:52.294 Setting [GENERAL] logLevel -> 2
M: 2020-04-16 18:30:52.294 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv
M: 2020-04-16 18:30:52.294 Setting [GENERAL] exportMetadata -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] decoderFallBack -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] useEmulator -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txPort -> 31103
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] rxPort -> 31100
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] ambeMode -> DMR
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] minTxTimeMS -> 2500
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] gatewayDmrId -> 7101003
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] repeaterID -> 710100306
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txTg -> 710411
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txTs -> 2
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] colorCode -> 1
M: 2020-04-16 18:30:52.294 Setting [USRP] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [USRP] txPort -> 32001
M: 2020-04-16 18:30:52.294 Setting [USRP] rxPort -> 34001
M: 2020-04-16 18:30:52.294 Setting [USRP] usrpAudio -> AUDIO_USE_GAIN
M: 2020-04-16 18:30:52.294 Setting [USRP] usrpGain -> .8
M: 2020-04-16 18:30:52.294 Setting [USRP] tlvAudio -> AUDIO_USE_GAIN
M: 2020-04-16 18:30:52.294 Setting [USRP] tlvGain -> 0.25
M: 2020-04-16 18:30:52.294 Setting [DV3000] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [DV3000] rxPort -> 2460
I: 2020-04-16 18:30:52.294 Open UDP listener on 127.0.0.1:31100
I: 2020-04-16 18:30:52.294 Open USRP on 127.0.0.1:32001
M: 2020-04-16 18:30:52.294 Connecting to DV3000 hardware......
W: 2020-04-16 18:30:53.325 DV3000 not found at 127.0.0.1:2460
I: 2020-04-16 18:30:53.326 Subscriber IDs loaded: 0
I: 2020-04-16 18:30:53.326 Default extended metadata <7101003>
I: 2020-04-16 18:30:53.326 Connecting to emulator on host 127.0.0.1:2470
W: 2020-04-16 18:30:53.326 Using software MBE decoder version 1.2.3
W: 2020-04-16 18:30:53.326 Using software OP25 IMBE/AMBE vocoder
I: 2020-04-16 18:30:53.326 Connected to USRP 127.0.0.1:32001
I: 2020-04-16 18:30:53.326 Starting TLV --> Analog_Bridge (decoder) --> USRP thread
I: 2020-04-16 18:30:53.327 Starting USRP --> Analog_Bridge (encoder) -> TLV thread
====================================================================================
MMDVM_Bridge Log

I: 2020-04-16 18:30:52.278 Portions Copyright (C) 2018 DVSwitch, INAD.
I: 2020-04-16 18:30:52.278 Hacks by Mike N4IRR and Steve N4IRS
I: 2020-04-16 18:30:52.278 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
I: 2020-04-16 18:30:52.278 This software is for use on amateur radio networks only,
I: 2020-04-16 18:30:52.278 it is to be used for educational purposes only. Its use on
I: 2020-04-16 18:30:52.278 commercial networks is strictly prohibited.
I: 2020-04-16 18:30:52.278 Copyright(C) 2015-2018 by Jonathan Naylor, G4KLX and others
M: 2020-04-16 18:30:52.278 MMDVM_Bridge-20191105_V1.4.1 is starting
M: 2020-04-16 18:30:52.278 Built 14:23:56 Nov 11 2019 (GitID #9dae1ac)
I: 2020-04-16 18:30:52.278 General Parameters
I: 2020-04-16 18:30:52.278     Callsign: YN1OB
I: 2020-04-16 18:30:52.278     Id: 710100306
I: 2020-04-16 18:30:52.278     Duplex: no
I: 2020-04-16 18:30:52.278     Timeout: 180s
I: 2020-04-16 18:30:52.278     D-Star: disabled
I: 2020-04-16 18:30:52.278     DMR: enabled
I: 2020-04-16 18:30:52.278     YSF: enabled
I: 2020-04-16 18:30:52.278     P25: disabled
I: 2020-04-16 18:30:52.278     NXDN: disabled
I: 2020-04-16 18:30:52.278 Modem Parameters
I: 2020-04-16 18:30:52.278     Port: /dev/null
I: 2020-04-16 18:30:52.278     RX Invert: no
I: 2020-04-16 18:30:52.278     TX Invert: no
I: 2020-04-16 18:30:52.278     PTT Invert: no
I: 2020-04-16 18:30:52.278     TX Delay: 100ms
I: 2020-04-16 18:30:52.278     RX Offset: 0Hz
I: 2020-04-16 18:30:52.278     TX Offset: 0Hz
I: 2020-04-16 18:30:52.278     RX DC Offset: 0
I: 2020-04-16 18:30:52.278     TX DC Offset: 0
I: 2020-04-16 18:30:52.278     RF Level: 100.0%
I: 2020-04-16 18:30:52.278     DMR Delay: 0 (0.0ms)
I: 2020-04-16 18:30:52.278     RX Level: 50.0%
I: 2020-04-16 18:30:52.278     CW Id TX Level: 50.0%
I: 2020-04-16 18:30:52.278     D-Star TX Level: 50.0%
I: 2020-04-16 18:30:52.278     DMR TX Level: 50.0%
I: 2020-04-16 18:30:52.278     YSF TX Level: 50.0%
I: 2020-04-16 18:30:52.278     P25 TX Level: 50.0%
I: 2020-04-16 18:30:52.278     NXDN TX Level: 50.0%
I: 2020-04-16 18:30:52.278     RX Frequency: 222340000Hz (222340000Hz)
I: 2020-04-16 18:30:52.278     TX Frequency: 224940000Hz (224940000Hz)
M: 2020-04-16 18:30:52.279 Opening the MMDVM
I: 2020-04-16 18:30:52.279 Display Parameters
I: 2020-04-16 18:30:52.279     Type: 
I: 2020-04-16 18:30:52.279 DMR Network Parameters
I: 2020-04-16 18:30:52.279     Address: 74.91.118.251 ;3103.repeater.net
I: 2020-04-16 18:30:52.279     Port: 62031
I: 2020-04-16 18:30:52.279     Local: 62032
I: 2020-04-16 18:30:52.279     Jitter: 360ms
I: 2020-04-16 18:30:52.279     Slot 1: disabled
I: 2020-04-16 18:30:52.279     Slot 2: enabled
I: 2020-04-16 18:30:52.279     Mode Hang: 3s
I: 2020-04-16 18:30:52.279 Info Parameters
I: 2020-04-16 18:30:52.279     Callsign: YN1OB
I: 2020-04-16 18:30:52.279     RX Frequency: 222340000Hz
I: 2020-04-16 18:30:52.279     TX Frequency: 224940000Hz
I: 2020-04-16 18:30:52.279     Power: 1W
I: 2020-04-16 18:30:52.279     Latitude: 41.733299deg N
I: 2020-04-16 18:30:52.279     Longitude: -50.399899deg E
I: 2020-04-16 18:30:52.279     Height: 0m
I: 2020-04-16 18:30:52.279     Location: "Iceberg, North Atlantic"
I: 2020-04-16 18:30:52.279     Description: "MMDVM_Bridge"
I: 2020-04-16 18:30:52.279     URL: "https://groups.io/g/DVSwitch"
M: 2020-04-16 18:30:52.279 DMR, Opening DMR Network
I: 2020-04-16 18:30:52.279 System Fusion Network Parameters
I: 2020-04-16 18:30:52.279     Local Address: 0
I: 2020-04-16 18:30:52.279     Local Port: 3200
I: 2020-04-16 18:30:52.279     Gateway Address: 149.248.2.133
I: 2020-04-16 18:30:52.279     Gateway Port: 42000
I: 2020-04-16 18:30:52.279     Mode Hang: 3s
M: 2020-04-16 18:30:52.279 Opening YSF network connection
I: 2020-04-16 18:30:52.279 RSSI
I: 2020-04-16 18:30:52.279     Mapping File: RSSI.dat
W: 2020-04-16 18:30:52.279 Cannot open the RSSI data file - RSSI.dat
I: 2020-04-16 18:30:52.280 DMR Id Lookups
I: 2020-04-16 18:30:52.280     File: /var/lib/mmdvm/DMRIds.dat
I: 2020-04-16 18:30:52.280     Reload: 24 hours
I: 2020-04-16 18:30:52.589 Loaded 161717 Ids to the DMR callsign lookup table
I: 2020-04-16 18:30:52.589 DMR RF Parameters
I: 2020-04-16 18:30:52.589     Id: 710100306
I: 2020-04-16 18:30:52.589     Color Code: 1
I: 2020-04-16 18:30:52.589     Self Only: no
I: 2020-04-16 18:30:52.589     Embedded LC Only: yes
I: 2020-04-16 18:30:52.589     Dump Talker Alias Data: no
I: 2020-04-16 18:30:52.589     Prefixes: 0
I: 2020-04-16 18:30:52.589     Call Hang: 3s
I: 2020-04-16 18:30:52.589     TX Hang: 3s
I: 2020-04-16 18:30:52.589     Mode Hang: 10s
M: 2020-04-16 18:30:52.589 DMR, Opening INI file: DVSwitch.ini
I: 2020-04-16 18:30:52.589 Started the DMR Id lookup reload thread
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] Address -> 127.0.0.1
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] TXPort -> 31100
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] RXPort -> 31103
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] Slot -> 2
M: 2020-04-16 18:30:52.590 DMR, Transmitting on 127.0.0.1:31100 and listening on port 31103.  Result = 1
I: 2020-04-16 18:30:52.590 YSF RF Parameters
I: 2020-04-16 18:30:52.590     Low Deviation: no
I: 2020-04-16 18:30:52.590     Remote Gateway: no
I: 2020-04-16 18:30:52.590     Self Only: no
I: 2020-04-16 18:30:52.590     DSQ: no
I: 2020-04-16 18:30:52.590     Mode Hang: 10s
M: 2020-04-16 18:30:52.590 YSF, Opening INI file: DVSwitch.ini
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] TXPort -> 31103
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] RXPort -> 31100
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] FallbackID -> 3128973
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] ExportTG -> 710411
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] Slot -> 2
M: 2020-04-16 18:30:52.590 YSF, Transmitting on 127.0.0.1:31103 and listening on port 31100.  Result = 1
M: 2020-04-16 18:30:52.590 MMDVM_Bridge-20191105_V1.4.1 is running
M: 2020-04-16 18:31:02.635 DMR, Logged into the master successfully
 


Steve N4IRS
 

Analog_Bridge is not used in a DMR to YSFn bridge.

On 4/16/2020 2:38 PM, Tito Lopez wrote:
Here is my Analog_Bridge Log


I: 2020-04-16 18:30:52.292 Analog_Bridge is starting
M: 2020-04-16 18:30:52.294 Setting [MACROS] DMR -> /opt/Analog_Bridge/dvswitch.sh mode DMR
M: 2020-04-16 18:30:52.294 Setting [MACROS] DSTAR -> /opt/Analog_Bridge/dvswitch.sh mode DSTAR
M: 2020-04-16 18:30:52.294 Setting [MACROS] NXDN -> /opt/Analog_Bridge/dvswitch.sh mode NXDN
M: 2020-04-16 18:30:52.294 Setting [MACROS] P25 -> /opt/Analog_Bridge/dvswitch.sh mode P25
M: 2020-04-16 18:30:52.294 Setting [MACROS] YSF -> /opt/Analog_Bridge/dvswitch.sh mode YSF
M: 2020-04-16 18:30:52.294 Setting [MACROS] dbupdate -> /opt/Analog_Bridge/dvswitch.sh collectProcessPushDataFiles
M: 2020-04-16 18:30:52.294 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh
M: 2020-04-16 18:30:52.294 Setting [] include -> dvsm.macro
M: 2020-04-16 18:30:52.294 Setting [GENERAL] logLevel -> 2
M: 2020-04-16 18:30:52.294 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv
M: 2020-04-16 18:30:52.294 Setting [GENERAL] exportMetadata -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] decoderFallBack -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] useEmulator -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txPort -> 31103
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] rxPort -> 31100
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] ambeMode -> DMR
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] minTxTimeMS -> 2500
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] gatewayDmrId -> 7101003
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] repeaterID -> 710100306
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txTg -> 710411
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txTs -> 2
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] colorCode -> 1
M: 2020-04-16 18:30:52.294 Setting [USRP] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [USRP] txPort -> 32001
M: 2020-04-16 18:30:52.294 Setting [USRP] rxPort -> 34001
M: 2020-04-16 18:30:52.294 Setting [USRP] usrpAudio -> AUDIO_USE_GAIN
M: 2020-04-16 18:30:52.294 Setting [USRP] usrpGain -> .8
M: 2020-04-16 18:30:52.294 Setting [USRP] tlvAudio -> AUDIO_USE_GAIN
M: 2020-04-16 18:30:52.294 Setting [USRP] tlvGain -> 0.25
M: 2020-04-16 18:30:52.294 Setting [DV3000] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [DV3000] rxPort -> 2460
I: 2020-04-16 18:30:52.294 Open UDP listener on 127.0.0.1:31100
I: 2020-04-16 18:30:52.294 Open USRP on 127.0.0.1:32001
M: 2020-04-16 18:30:52.294 Connecting to DV3000 hardware......
W: 2020-04-16 18:30:53.325 DV3000 not found at 127.0.0.1:2460
I: 2020-04-16 18:30:53.326 Subscriber IDs loaded: 0
I: 2020-04-16 18:30:53.326 Default extended metadata <7101003>
I: 2020-04-16 18:30:53.326 Connecting to emulator on host 127.0.0.1:2470
W: 2020-04-16 18:30:53.326 Using software MBE decoder version 1.2.3
W: 2020-04-16 18:30:53.326 Using software OP25 IMBE/AMBE vocoder
I: 2020-04-16 18:30:53.326 Connected to USRP 127.0.0.1:32001
I: 2020-04-16 18:30:53.326 Starting TLV --> Analog_Bridge (decoder) --> USRP thread
I: 2020-04-16 18:30:53.327 Starting USRP --> Analog_Bridge (encoder) -> TLV thread
====================================================================================
MMDVM_Bridge Log

I: 2020-04-16 18:30:52.278 Portions Copyright (C) 2018 DVSwitch, INAD.
I: 2020-04-16 18:30:52.278 Hacks by Mike N4IRR and Steve N4IRS
I: 2020-04-16 18:30:52.278 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
I: 2020-04-16 18:30:52.278 This software is for use on amateur radio networks only,
I: 2020-04-16 18:30:52.278 it is to be used for educational purposes only. Its use on
I: 2020-04-16 18:30:52.278 commercial networks is strictly prohibited.
I: 2020-04-16 18:30:52.278 Copyright(C) 2015-2018 by Jonathan Naylor, G4KLX and others
M: 2020-04-16 18:30:52.278 MMDVM_Bridge-20191105_V1.4.1 is starting
M: 2020-04-16 18:30:52.278 Built 14:23:56 Nov 11 2019 (GitID #9dae1ac)
I: 2020-04-16 18:30:52.278 General Parameters
I: 2020-04-16 18:30:52.278     Callsign: YN1OB
I: 2020-04-16 18:30:52.278     Id: 710100306
I: 2020-04-16 18:30:52.278     Duplex: no
I: 2020-04-16 18:30:52.278     Timeout: 180s
I: 2020-04-16 18:30:52.278     D-Star: disabled
I: 2020-04-16 18:30:52.278     DMR: enabled
I: 2020-04-16 18:30:52.278     YSF: enabled
I: 2020-04-16 18:30:52.278     P25: disabled
I: 2020-04-16 18:30:52.278     NXDN: disabled
I: 2020-04-16 18:30:52.278 Modem Parameters
I: 2020-04-16 18:30:52.278     Port: /dev/null
I: 2020-04-16 18:30:52.278     RX Invert: no
I: 2020-04-16 18:30:52.278     TX Invert: no
I: 2020-04-16 18:30:52.278     PTT Invert: no
I: 2020-04-16 18:30:52.278     TX Delay: 100ms
I: 2020-04-16 18:30:52.278     RX Offset: 0Hz
I: 2020-04-16 18:30:52.278     TX Offset: 0Hz
I: 2020-04-16 18:30:52.278     RX DC Offset: 0
I: 2020-04-16 18:30:52.278     TX DC Offset: 0
I: 2020-04-16 18:30:52.278     RF Level: 100.0%
I: 2020-04-16 18:30:52.278     DMR Delay: 0 (0.0ms)
I: 2020-04-16 18:30:52.278     RX Level: 50.0%
I: 2020-04-16 18:30:52.278     CW Id TX Level: 50.0%
I: 2020-04-16 18:30:52.278     D-Star TX Level: 50.0%
I: 2020-04-16 18:30:52.278     DMR TX Level: 50.0%
I: 2020-04-16 18:30:52.278     YSF TX Level: 50.0%
I: 2020-04-16 18:30:52.278     P25 TX Level: 50.0%
I: 2020-04-16 18:30:52.278     NXDN TX Level: 50.0%
I: 2020-04-16 18:30:52.278     RX Frequency: 222340000Hz (222340000Hz)
I: 2020-04-16 18:30:52.278     TX Frequency: 224940000Hz (224940000Hz)
M: 2020-04-16 18:30:52.279 Opening the MMDVM
I: 2020-04-16 18:30:52.279 Display Parameters
I: 2020-04-16 18:30:52.279     Type: 
I: 2020-04-16 18:30:52.279 DMR Network Parameters
I: 2020-04-16 18:30:52.279     Address: 74.91.118.251 ;3103.repeater.net
I: 2020-04-16 18:30:52.279     Port: 62031
I: 2020-04-16 18:30:52.279     Local: 62032
I: 2020-04-16 18:30:52.279     Jitter: 360ms
I: 2020-04-16 18:30:52.279     Slot 1: disabled
I: 2020-04-16 18:30:52.279     Slot 2: enabled
I: 2020-04-16 18:30:52.279     Mode Hang: 3s
I: 2020-04-16 18:30:52.279 Info Parameters
I: 2020-04-16 18:30:52.279     Callsign: YN1OB
I: 2020-04-16 18:30:52.279     RX Frequency: 222340000Hz
I: 2020-04-16 18:30:52.279     TX Frequency: 224940000Hz
I: 2020-04-16 18:30:52.279     Power: 1W
I: 2020-04-16 18:30:52.279     Latitude: 41.733299deg N
I: 2020-04-16 18:30:52.279     Longitude: -50.399899deg E
I: 2020-04-16 18:30:52.279     Height: 0m
I: 2020-04-16 18:30:52.279     Location: "Iceberg, North Atlantic"
I: 2020-04-16 18:30:52.279     Description: "MMDVM_Bridge"
I: 2020-04-16 18:30:52.279     URL: "https://groups.io/g/DVSwitch"
M: 2020-04-16 18:30:52.279 DMR, Opening DMR Network
I: 2020-04-16 18:30:52.279 System Fusion Network Parameters
I: 2020-04-16 18:30:52.279     Local Address: 0
I: 2020-04-16 18:30:52.279     Local Port: 3200
I: 2020-04-16 18:30:52.279     Gateway Address: 149.248.2.133
I: 2020-04-16 18:30:52.279     Gateway Port: 42000
I: 2020-04-16 18:30:52.279     Mode Hang: 3s
M: 2020-04-16 18:30:52.279 Opening YSF network connection
I: 2020-04-16 18:30:52.279 RSSI
I: 2020-04-16 18:30:52.279     Mapping File: RSSI.dat
W: 2020-04-16 18:30:52.279 Cannot open the RSSI data file - RSSI.dat
I: 2020-04-16 18:30:52.280 DMR Id Lookups
I: 2020-04-16 18:30:52.280     File: /var/lib/mmdvm/DMRIds.dat
I: 2020-04-16 18:30:52.280     Reload: 24 hours
I: 2020-04-16 18:30:52.589 Loaded 161717 Ids to the DMR callsign lookup table
I: 2020-04-16 18:30:52.589 DMR RF Parameters
I: 2020-04-16 18:30:52.589     Id: 710100306
I: 2020-04-16 18:30:52.589     Color Code: 1
I: 2020-04-16 18:30:52.589     Self Only: no
I: 2020-04-16 18:30:52.589     Embedded LC Only: yes
I: 2020-04-16 18:30:52.589     Dump Talker Alias Data: no
I: 2020-04-16 18:30:52.589     Prefixes: 0
I: 2020-04-16 18:30:52.589     Call Hang: 3s
I: 2020-04-16 18:30:52.589     TX Hang: 3s
I: 2020-04-16 18:30:52.589     Mode Hang: 10s
M: 2020-04-16 18:30:52.589 DMR, Opening INI file: DVSwitch.ini
I: 2020-04-16 18:30:52.589 Started the DMR Id lookup reload thread
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] Address -> 127.0.0.1
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] TXPort -> 31100
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] RXPort -> 31103
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] Slot -> 2
M: 2020-04-16 18:30:52.590 DMR, Transmitting on 127.0.0.1:31100 and listening on port 31103.  Result = 1
I: 2020-04-16 18:30:52.590 YSF RF Parameters
I: 2020-04-16 18:30:52.590     Low Deviation: no
I: 2020-04-16 18:30:52.590     Remote Gateway: no
I: 2020-04-16 18:30:52.590     Self Only: no
I: 2020-04-16 18:30:52.590     DSQ: no
I: 2020-04-16 18:30:52.590     Mode Hang: 10s
M: 2020-04-16 18:30:52.590 YSF, Opening INI file: DVSwitch.ini
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] TXPort -> 31103
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] RXPort -> 31100
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] FallbackID -> 3128973
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] ExportTG -> 710411
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] Slot -> 2
M: 2020-04-16 18:30:52.590 YSF, Transmitting on 127.0.0.1:31103 and listening on port 31100.  Result = 1
M: 2020-04-16 18:30:52.590 MMDVM_Bridge-20191105_V1.4.1 is running
M: 2020-04-16 18:31:02.635 DMR, Logged into the master successfully
 


Tito Lopez - YN1OB
 

So what is it  that you need?


On Thu, Apr 16, 2020 at 12:52 PM Steve N4IRS <szingman@...> wrote:
Analog_Bridge is not used in a DMR to YSFn bridge.

On 4/16/2020 2:38 PM, Tito Lopez wrote:
Here is my Analog_Bridge Log


I: 2020-04-16 18:30:52.292 Analog_Bridge is starting
M: 2020-04-16 18:30:52.294 Setting [MACROS] DMR -> /opt/Analog_Bridge/dvswitch.sh mode DMR
M: 2020-04-16 18:30:52.294 Setting [MACROS] DSTAR -> /opt/Analog_Bridge/dvswitch.sh mode DSTAR
M: 2020-04-16 18:30:52.294 Setting [MACROS] NXDN -> /opt/Analog_Bridge/dvswitch.sh mode NXDN
M: 2020-04-16 18:30:52.294 Setting [MACROS] P25 -> /opt/Analog_Bridge/dvswitch.sh mode P25
M: 2020-04-16 18:30:52.294 Setting [MACROS] YSF -> /opt/Analog_Bridge/dvswitch.sh mode YSF
M: 2020-04-16 18:30:52.294 Setting [MACROS] dbupdate -> /opt/Analog_Bridge/dvswitch.sh collectProcessPushDataFiles
M: 2020-04-16 18:30:52.294 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh
M: 2020-04-16 18:30:52.294 Setting [] include -> dvsm.macro
M: 2020-04-16 18:30:52.294 Setting [GENERAL] logLevel -> 2
M: 2020-04-16 18:30:52.294 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv
M: 2020-04-16 18:30:52.294 Setting [GENERAL] exportMetadata -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] decoderFallBack -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] useEmulator -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txPort -> 31103
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] rxPort -> 31100
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] ambeMode -> DMR
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] minTxTimeMS -> 2500
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] gatewayDmrId -> 7101003
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] repeaterID -> 710100306
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txTg -> 710411
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txTs -> 2
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] colorCode -> 1
M: 2020-04-16 18:30:52.294 Setting [USRP] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [USRP] txPort -> 32001
M: 2020-04-16 18:30:52.294 Setting [USRP] rxPort -> 34001
M: 2020-04-16 18:30:52.294 Setting [USRP] usrpAudio -> AUDIO_USE_GAIN
M: 2020-04-16 18:30:52.294 Setting [USRP] usrpGain -> .8
M: 2020-04-16 18:30:52.294 Setting [USRP] tlvAudio -> AUDIO_USE_GAIN
M: 2020-04-16 18:30:52.294 Setting [USRP] tlvGain -> 0.25
M: 2020-04-16 18:30:52.294 Setting [DV3000] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [DV3000] rxPort -> 2460
I: 2020-04-16 18:30:52.294 Open UDP listener on 127.0.0.1:31100
I: 2020-04-16 18:30:52.294 Open USRP on 127.0.0.1:32001
M: 2020-04-16 18:30:52.294 Connecting to DV3000 hardware......
W: 2020-04-16 18:30:53.325 DV3000 not found at 127.0.0.1:2460
I: 2020-04-16 18:30:53.326 Subscriber IDs loaded: 0
I: 2020-04-16 18:30:53.326 Default extended metadata <7101003>
I: 2020-04-16 18:30:53.326 Connecting to emulator on host 127.0.0.1:2470
W: 2020-04-16 18:30:53.326 Using software MBE decoder version 1.2.3
W: 2020-04-16 18:30:53.326 Using software OP25 IMBE/AMBE vocoder
I: 2020-04-16 18:30:53.326 Connected to USRP 127.0.0.1:32001
I: 2020-04-16 18:30:53.326 Starting TLV --> Analog_Bridge (decoder) --> USRP thread
I: 2020-04-16 18:30:53.327 Starting USRP --> Analog_Bridge (encoder) -> TLV thread
====================================================================================
MMDVM_Bridge Log

I: 2020-04-16 18:30:52.278 Portions Copyright (C) 2018 DVSwitch, INAD.
I: 2020-04-16 18:30:52.278 Hacks by Mike N4IRR and Steve N4IRS
I: 2020-04-16 18:30:52.278 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
I: 2020-04-16 18:30:52.278 This software is for use on amateur radio networks only,
I: 2020-04-16 18:30:52.278 it is to be used for educational purposes only. Its use on
I: 2020-04-16 18:30:52.278 commercial networks is strictly prohibited.
I: 2020-04-16 18:30:52.278 Copyright(C) 2015-2018 by Jonathan Naylor, G4KLX and others
M: 2020-04-16 18:30:52.278 MMDVM_Bridge-20191105_V1.4.1 is starting
M: 2020-04-16 18:30:52.278 Built 14:23:56 Nov 11 2019 (GitID #9dae1ac)
I: 2020-04-16 18:30:52.278 General Parameters
I: 2020-04-16 18:30:52.278     Callsign: YN1OB
I: 2020-04-16 18:30:52.278     Id: 710100306
I: 2020-04-16 18:30:52.278     Duplex: no
I: 2020-04-16 18:30:52.278     Timeout: 180s
I: 2020-04-16 18:30:52.278     D-Star: disabled
I: 2020-04-16 18:30:52.278     DMR: enabled
I: 2020-04-16 18:30:52.278     YSF: enabled
I: 2020-04-16 18:30:52.278     P25: disabled
I: 2020-04-16 18:30:52.278     NXDN: disabled
I: 2020-04-16 18:30:52.278 Modem Parameters
I: 2020-04-16 18:30:52.278     Port: /dev/null
I: 2020-04-16 18:30:52.278     RX Invert: no
I: 2020-04-16 18:30:52.278     TX Invert: no
I: 2020-04-16 18:30:52.278     PTT Invert: no
I: 2020-04-16 18:30:52.278     TX Delay: 100ms
I: 2020-04-16 18:30:52.278     RX Offset: 0Hz
I: 2020-04-16 18:30:52.278     TX Offset: 0Hz
I: 2020-04-16 18:30:52.278     RX DC Offset: 0
I: 2020-04-16 18:30:52.278     TX DC Offset: 0
I: 2020-04-16 18:30:52.278     RF Level: 100.0%
I: 2020-04-16 18:30:52.278     DMR Delay: 0 (0.0ms)
I: 2020-04-16 18:30:52.278     RX Level: 50.0%
I: 2020-04-16 18:30:52.278     CW Id TX Level: 50.0%
I: 2020-04-16 18:30:52.278     D-Star TX Level: 50.0%
I: 2020-04-16 18:30:52.278     DMR TX Level: 50.0%
I: 2020-04-16 18:30:52.278     YSF TX Level: 50.0%
I: 2020-04-16 18:30:52.278     P25 TX Level: 50.0%
I: 2020-04-16 18:30:52.278     NXDN TX Level: 50.0%
I: 2020-04-16 18:30:52.278     RX Frequency: 222340000Hz (222340000Hz)
I: 2020-04-16 18:30:52.278     TX Frequency: 224940000Hz (224940000Hz)
M: 2020-04-16 18:30:52.279 Opening the MMDVM
I: 2020-04-16 18:30:52.279 Display Parameters
I: 2020-04-16 18:30:52.279     Type: 
I: 2020-04-16 18:30:52.279 DMR Network Parameters
I: 2020-04-16 18:30:52.279     Address: 74.91.118.251 ;3103.repeater.net
I: 2020-04-16 18:30:52.279     Port: 62031
I: 2020-04-16 18:30:52.279     Local: 62032
I: 2020-04-16 18:30:52.279     Jitter: 360ms
I: 2020-04-16 18:30:52.279     Slot 1: disabled
I: 2020-04-16 18:30:52.279     Slot 2: enabled
I: 2020-04-16 18:30:52.279     Mode Hang: 3s
I: 2020-04-16 18:30:52.279 Info Parameters
I: 2020-04-16 18:30:52.279     Callsign: YN1OB
I: 2020-04-16 18:30:52.279     RX Frequency: 222340000Hz
I: 2020-04-16 18:30:52.279     TX Frequency: 224940000Hz
I: 2020-04-16 18:30:52.279     Power: 1W
I: 2020-04-16 18:30:52.279     Latitude: 41.733299deg N
I: 2020-04-16 18:30:52.279     Longitude: -50.399899deg E
I: 2020-04-16 18:30:52.279     Height: 0m
I: 2020-04-16 18:30:52.279     Location: "Iceberg, North Atlantic"
I: 2020-04-16 18:30:52.279     Description: "MMDVM_Bridge"
I: 2020-04-16 18:30:52.279     URL: "https://groups.io/g/DVSwitch"
M: 2020-04-16 18:30:52.279 DMR, Opening DMR Network
I: 2020-04-16 18:30:52.279 System Fusion Network Parameters
I: 2020-04-16 18:30:52.279     Local Address: 0
I: 2020-04-16 18:30:52.279     Local Port: 3200
I: 2020-04-16 18:30:52.279     Gateway Address: 149.248.2.133
I: 2020-04-16 18:30:52.279     Gateway Port: 42000
I: 2020-04-16 18:30:52.279     Mode Hang: 3s
M: 2020-04-16 18:30:52.279 Opening YSF network connection
I: 2020-04-16 18:30:52.279 RSSI
I: 2020-04-16 18:30:52.279     Mapping File: RSSI.dat
W: 2020-04-16 18:30:52.279 Cannot open the RSSI data file - RSSI.dat
I: 2020-04-16 18:30:52.280 DMR Id Lookups
I: 2020-04-16 18:30:52.280     File: /var/lib/mmdvm/DMRIds.dat
I: 2020-04-16 18:30:52.280     Reload: 24 hours
I: 2020-04-16 18:30:52.589 Loaded 161717 Ids to the DMR callsign lookup table
I: 2020-04-16 18:30:52.589 DMR RF Parameters
I: 2020-04-16 18:30:52.589     Id: 710100306
I: 2020-04-16 18:30:52.589     Color Code: 1
I: 2020-04-16 18:30:52.589     Self Only: no
I: 2020-04-16 18:30:52.589     Embedded LC Only: yes
I: 2020-04-16 18:30:52.589     Dump Talker Alias Data: no
I: 2020-04-16 18:30:52.589     Prefixes: 0
I: 2020-04-16 18:30:52.589     Call Hang: 3s
I: 2020-04-16 18:30:52.589     TX Hang: 3s
I: 2020-04-16 18:30:52.589     Mode Hang: 10s
M: 2020-04-16 18:30:52.589 DMR, Opening INI file: DVSwitch.ini
I: 2020-04-16 18:30:52.589 Started the DMR Id lookup reload thread
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] Address -> 127.0.0.1
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] TXPort -> 31100
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] RXPort -> 31103
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] Slot -> 2
M: 2020-04-16 18:30:52.590 DMR, Transmitting on 127.0.0.1:31100 and listening on port 31103.  Result = 1
I: 2020-04-16 18:30:52.590 YSF RF Parameters
I: 2020-04-16 18:30:52.590     Low Deviation: no
I: 2020-04-16 18:30:52.590     Remote Gateway: no
I: 2020-04-16 18:30:52.590     Self Only: no
I: 2020-04-16 18:30:52.590     DSQ: no
I: 2020-04-16 18:30:52.590     Mode Hang: 10s
M: 2020-04-16 18:30:52.590 YSF, Opening INI file: DVSwitch.ini
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] TXPort -> 31103
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] RXPort -> 31100
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] FallbackID -> 3128973
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] ExportTG -> 710411
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] Slot -> 2
M: 2020-04-16 18:30:52.590 YSF, Transmitting on 127.0.0.1:31103 and listening on port 31100.  Result = 1
M: 2020-04-16 18:30:52.590 MMDVM_Bridge-20191105_V1.4.1 is running
M: 2020-04-16 18:31:02.635 DMR, Logged into the master successfully
 


Steve N4IRS
 

What program are you running to build the bridge? I need that log with traffic in both directions.
<https://dvswitch.groups.io/g/main/wiki/Bridge-DMR-to-YSF-Narrow>
<https://dvswitch.groups.io/g/main/wiki/Help%21>

On 4/16/20 5:44 PM, Tito Lopez wrote:
So what is it  that you need?

On Thu, Apr 16, 2020 at 12:52 PM Steve N4IRS <szingman@...> wrote:
Analog_Bridge is not used in a DMR to YSFn bridge.

On 4/16/2020 2:38 PM, Tito Lopez wrote:
Here is my Analog_Bridge Log


I: 2020-04-16 18:30:52.292 Analog_Bridge is starting
M: 2020-04-16 18:30:52.294 Setting [MACROS] DMR -> /opt/Analog_Bridge/dvswitch.sh mode DMR
M: 2020-04-16 18:30:52.294 Setting [MACROS] DSTAR -> /opt/Analog_Bridge/dvswitch.sh mode DSTAR
M: 2020-04-16 18:30:52.294 Setting [MACROS] NXDN -> /opt/Analog_Bridge/dvswitch.sh mode NXDN
M: 2020-04-16 18:30:52.294 Setting [MACROS] P25 -> /opt/Analog_Bridge/dvswitch.sh mode P25
M: 2020-04-16 18:30:52.294 Setting [MACROS] YSF -> /opt/Analog_Bridge/dvswitch.sh mode YSF
M: 2020-04-16 18:30:52.294 Setting [MACROS] dbupdate -> /opt/Analog_Bridge/dvswitch.sh collectProcessPushDataFiles
M: 2020-04-16 18:30:52.294 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh
M: 2020-04-16 18:30:52.294 Setting [] include -> dvsm.macro
M: 2020-04-16 18:30:52.294 Setting [GENERAL] logLevel -> 2
M: 2020-04-16 18:30:52.294 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv
M: 2020-04-16 18:30:52.294 Setting [GENERAL] exportMetadata -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] decoderFallBack -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] useEmulator -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txPort -> 31103
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] rxPort -> 31100
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] ambeMode -> DMR
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] minTxTimeMS -> 2500
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] gatewayDmrId -> 7101003
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] repeaterID -> 710100306
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txTg -> 710411
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txTs -> 2
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] colorCode -> 1
M: 2020-04-16 18:30:52.294 Setting [USRP] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [USRP] txPort -> 32001
M: 2020-04-16 18:30:52.294 Setting [USRP] rxPort -> 34001
M: 2020-04-16 18:30:52.294 Setting [USRP] usrpAudio -> AUDIO_USE_GAIN
M: 2020-04-16 18:30:52.294 Setting [USRP] usrpGain -> .8
M: 2020-04-16 18:30:52.294 Setting [USRP] tlvAudio -> AUDIO_USE_GAIN
M: 2020-04-16 18:30:52.294 Setting [USRP] tlvGain -> 0.25
M: 2020-04-16 18:30:52.294 Setting [DV3000] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [DV3000] rxPort -> 2460
I: 2020-04-16 18:30:52.294 Open UDP listener on 127.0.0.1:31100
I: 2020-04-16 18:30:52.294 Open USRP on 127.0.0.1:32001
M: 2020-04-16 18:30:52.294 Connecting to DV3000 hardware......
W: 2020-04-16 18:30:53.325 DV3000 not found at 127.0.0.1:2460
I: 2020-04-16 18:30:53.326 Subscriber IDs loaded: 0
I: 2020-04-16 18:30:53.326 Default extended metadata <7101003>
I: 2020-04-16 18:30:53.326 Connecting to emulator on host 127.0.0.1:2470
W: 2020-04-16 18:30:53.326 Using software MBE decoder version 1.2.3
W: 2020-04-16 18:30:53.326 Using software OP25 IMBE/AMBE vocoder
I: 2020-04-16 18:30:53.326 Connected to USRP 127.0.0.1:32001
I: 2020-04-16 18:30:53.326 Starting TLV --> Analog_Bridge (decoder) --> USRP thread
I: 2020-04-16 18:30:53.327 Starting USRP --> Analog_Bridge (encoder) -> TLV thread
====================================================================================
MMDVM_Bridge Log

I: 2020-04-16 18:30:52.278 Portions Copyright (C) 2018 DVSwitch, INAD.
I: 2020-04-16 18:30:52.278 Hacks by Mike N4IRR and Steve N4IRS
I: 2020-04-16 18:30:52.278 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
I: 2020-04-16 18:30:52.278 This software is for use on amateur radio networks only,
I: 2020-04-16 18:30:52.278 it is to be used for educational purposes only. Its use on
I: 2020-04-16 18:30:52.278 commercial networks is strictly prohibited.
I: 2020-04-16 18:30:52.278 Copyright(C) 2015-2018 by Jonathan Naylor, G4KLX and others
M: 2020-04-16 18:30:52.278 MMDVM_Bridge-20191105_V1.4.1 is starting
M: 2020-04-16 18:30:52.278 Built 14:23:56 Nov 11 2019 (GitID #9dae1ac)
I: 2020-04-16 18:30:52.278 General Parameters
I: 2020-04-16 18:30:52.278     Callsign: YN1OB
I: 2020-04-16 18:30:52.278     Id: 710100306
I: 2020-04-16 18:30:52.278     Duplex: no
I: 2020-04-16 18:30:52.278     Timeout: 180s
I: 2020-04-16 18:30:52.278     D-Star: disabled
I: 2020-04-16 18:30:52.278     DMR: enabled
I: 2020-04-16 18:30:52.278     YSF: enabled
I: 2020-04-16 18:30:52.278     P25: disabled
I: 2020-04-16 18:30:52.278     NXDN: disabled
I: 2020-04-16 18:30:52.278 Modem Parameters
I: 2020-04-16 18:30:52.278     Port: /dev/null
I: 2020-04-16 18:30:52.278     RX Invert: no
I: 2020-04-16 18:30:52.278     TX Invert: no
I: 2020-04-16 18:30:52.278     PTT Invert: no
I: 2020-04-16 18:30:52.278     TX Delay: 100ms
I: 2020-04-16 18:30:52.278     RX Offset: 0Hz
I: 2020-04-16 18:30:52.278     TX Offset: 0Hz
I: 2020-04-16 18:30:52.278     RX DC Offset: 0
I: 2020-04-16 18:30:52.278     TX DC Offset: 0
I: 2020-04-16 18:30:52.278     RF Level: 100.0%
I: 2020-04-16 18:30:52.278     DMR Delay: 0 (0.0ms)
I: 2020-04-16 18:30:52.278     RX Level: 50.0%
I: 2020-04-16 18:30:52.278     CW Id TX Level: 50.0%
I: 2020-04-16 18:30:52.278     D-Star TX Level: 50.0%
I: 2020-04-16 18:30:52.278     DMR TX Level: 50.0%
I: 2020-04-16 18:30:52.278     YSF TX Level: 50.0%
I: 2020-04-16 18:30:52.278     P25 TX Level: 50.0%
I: 2020-04-16 18:30:52.278     NXDN TX Level: 50.0%
I: 2020-04-16 18:30:52.278     RX Frequency: 222340000Hz (222340000Hz)
I: 2020-04-16 18:30:52.278     TX Frequency: 224940000Hz (224940000Hz)
M: 2020-04-16 18:30:52.279 Opening the MMDVM
I: 2020-04-16 18:30:52.279 Display Parameters
I: 2020-04-16 18:30:52.279     Type: 
I: 2020-04-16 18:30:52.279 DMR Network Parameters
I: 2020-04-16 18:30:52.279     Address: 74.91.118.251 ;3103.repeater.net
I: 2020-04-16 18:30:52.279     Port: 62031
I: 2020-04-16 18:30:52.279     Local: 62032
I: 2020-04-16 18:30:52.279     Jitter: 360ms
I: 2020-04-16 18:30:52.279     Slot 1: disabled
I: 2020-04-16 18:30:52.279     Slot 2: enabled
I: 2020-04-16 18:30:52.279     Mode Hang: 3s
I: 2020-04-16 18:30:52.279 Info Parameters
I: 2020-04-16 18:30:52.279     Callsign: YN1OB
I: 2020-04-16 18:30:52.279     RX Frequency: 222340000Hz
I: 2020-04-16 18:30:52.279     TX Frequency: 224940000Hz
I: 2020-04-16 18:30:52.279     Power: 1W
I: 2020-04-16 18:30:52.279     Latitude: 41.733299deg N
I: 2020-04-16 18:30:52.279     Longitude: -50.399899deg E
I: 2020-04-16 18:30:52.279     Height: 0m
I: 2020-04-16 18:30:52.279     Location: "Iceberg, North Atlantic"
I: 2020-04-16 18:30:52.279     Description: "MMDVM_Bridge"
I: 2020-04-16 18:30:52.279     URL: "https://groups.io/g/DVSwitch"
M: 2020-04-16 18:30:52.279 DMR, Opening DMR Network
I: 2020-04-16 18:30:52.279 System Fusion Network Parameters
I: 2020-04-16 18:30:52.279     Local Address: 0
I: 2020-04-16 18:30:52.279     Local Port: 3200
I: 2020-04-16 18:30:52.279     Gateway Address: 149.248.2.133
I: 2020-04-16 18:30:52.279     Gateway Port: 42000
I: 2020-04-16 18:30:52.279     Mode Hang: 3s
M: 2020-04-16 18:30:52.279 Opening YSF network connection
I: 2020-04-16 18:30:52.279 RSSI
I: 2020-04-16 18:30:52.279     Mapping File: RSSI.dat
W: 2020-04-16 18:30:52.279 Cannot open the RSSI data file - RSSI.dat
I: 2020-04-16 18:30:52.280 DMR Id Lookups
I: 2020-04-16 18:30:52.280     File: /var/lib/mmdvm/DMRIds.dat
I: 2020-04-16 18:30:52.280     Reload: 24 hours
I: 2020-04-16 18:30:52.589 Loaded 161717 Ids to the DMR callsign lookup table
I: 2020-04-16 18:30:52.589 DMR RF Parameters
I: 2020-04-16 18:30:52.589     Id: 710100306
I: 2020-04-16 18:30:52.589     Color Code: 1
I: 2020-04-16 18:30:52.589     Self Only: no
I: 2020-04-16 18:30:52.589     Embedded LC Only: yes
I: 2020-04-16 18:30:52.589     Dump Talker Alias Data: no
I: 2020-04-16 18:30:52.589     Prefixes: 0
I: 2020-04-16 18:30:52.589     Call Hang: 3s
I: 2020-04-16 18:30:52.589     TX Hang: 3s
I: 2020-04-16 18:30:52.589     Mode Hang: 10s
M: 2020-04-16 18:30:52.589 DMR, Opening INI file: DVSwitch.ini
I: 2020-04-16 18:30:52.589 Started the DMR Id lookup reload thread
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] Address -> 127.0.0.1
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] TXPort -> 31100
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] RXPort -> 31103
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] Slot -> 2
M: 2020-04-16 18:30:52.590 DMR, Transmitting on 127.0.0.1:31100 and listening on port 31103.  Result = 1
I: 2020-04-16 18:30:52.590 YSF RF Parameters
I: 2020-04-16 18:30:52.590     Low Deviation: no
I: 2020-04-16 18:30:52.590     Remote Gateway: no
I: 2020-04-16 18:30:52.590     Self Only: no
I: 2020-04-16 18:30:52.590     DSQ: no
I: 2020-04-16 18:30:52.590     Mode Hang: 10s
M: 2020-04-16 18:30:52.590 YSF, Opening INI file: DVSwitch.ini
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] TXPort -> 31103
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] RXPort -> 31100
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] FallbackID -> 3128973
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] ExportTG -> 710411
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] Slot -> 2
M: 2020-04-16 18:30:52.590 YSF, Transmitting on 127.0.0.1:31103 and listening on port 31100.  Result = 1
M: 2020-04-16 18:30:52.590 MMDVM_Bridge-20191105_V1.4.1 is running
M: 2020-04-16 18:31:02.635 DMR, Logged into the master successfully
 



Uli
 

@Tito: Did you open up all necessary ports on your router? That was one of my problems in the first place that prevented the connection
Try to run something like   tail -f /var/log/mmdvm/MMDVM_Bridge-2020-04-17.log    (replace the date with the current date) to display a live log and check what is going on
Now take a DMR HT and a C4fm HT key up and check whats shown in the livelog

@Steve: I have no clue why the DVSwitch system builder did not work. It might have been a user rights problem or it did not like the raspbian stretch lite, but I don´t know for sure.
When I have time, I´ll give it another try.

Uli


Uli
 

@Tito: I have put your YSF Reflector IP into my MMDVM_Bridge.ini file rebooted and did a few tests. It works fine, I get audio in both directions.
Did you open up in your router port 42000 UDP pointing to the IP of your RPI with the MMDVM_Bridge running on it?

Uli


Tito Lopez - YN1OB
 

Ah so you are the one that is connected to the reflector.  Cool. So it works fine.
 The problem is on my end. 


On Fri, Apr 17, 2020 at 10:11 AM Uli <g90@...> wrote:
@Tito: I have put your YSF Reflector IP into my MMDVM_Bridge.ini file rebooted and did a few tests. It works fine, I get audio in both directions.
Did you open up in your router port 42000 UDP pointing to the IP of your RPI with the MMDVM_Bridge running on it?

Uli


Uli
 

Yes that was me yesterday on your Reflector testing.
Can you post you MMDVM_Bridge.ini and your DVSwitch.ini so that I can compare it to mine?
Maybe that gives a hint where the problem lies.

Uli


Aaron Groover
 

This is where i get stuck. How does it communicate without Analog_Bridge.ini?


Steve N4IRS
 

Because it's all digital. No need for a Analog component.

On 11/16/2020 8:43 AM, Aaron Groover wrote:
This is where i get stuck. How does it communicate without Analog_Bridge.ini?


KC1JFN
 

Hi, I have the same set up with Uli, both RPI running on raspbian stretch lite on the same network. I did what Steve told Uli to do by pointing MMDVM_Bridge at the 2 systems you want to bridge. But it does not work. I am a newbie with regards to this things. 

Is it only on MMDVm_Bridge.ini that I have to change?
What does it mean by  GatewayAddress=ysfreflector.dvswitch.org <-------- point this at the YSF reflector? The ip address to the YSF Reflector is, My public ip?

I downloaded this from YSF Reflector registry
07854;US-ICARE-Iloilo;ICARE Iloilo;32.214.141.124;42002;001;http://ic6008.com/Dashboard
This is what I put in
GatewayAddress=
32.214.141.124
GatewayPort=42002

Please help, Thank you


KC1JFN
 

I did some experiment, since the bridge and the YSF reflector are on the same LAN. I change the GatewayAddress=to the local ip address of the YSF Reflector server, which is also on the same network with the YSF to DMR Bridge.

KC1JFN