ASL<>AB
|
Steve Siesel [K4KSA]
Can you look at this as well…..
I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that.
Steve
; Your Repeater
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
[460310] ; Change this to your assigned node number
; Must also be enabled in modules.conf ; Rx audio/signalling channel. Choose ONLY 1 per node stanza
; Enable the selected channel driver in modules.conf !!! rxchannel = dahdi/pseudo ; No radio (hub) ; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_1999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP ; rxchannel = Voter/1999 ; RTCM device
duplex = 1 ; 0 = Half duplex with no telemetry tones or hang time. ; Special Case: Full duplex if linktolink is set to yes. ; This mode is preferred when interfacing with an external multiport repeater controller. ; Comment out idrecording and idtalkover to suppress IDs also ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio. ; This mode is preferred when interfacing a simplex node. ; 2 = Full Duplex with telemetry tones and hang time. ; This mode is preferred when interfacing a repeater. ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio. ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.
linktolink = no ; disables forcing physical half-duplex operation of main repeater while ; still keeping half-duplex semantics (optional)
linkmongain = 0 ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received. ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db. ; If linkmongain set to a positive number monitored audio will increase by the set amount in db. ; The value of linkmongain is in db. The default value is 0 db.
erxgain = -3 ; Echolink receive gain adjustment ; Note: Gain is in db-volts (20logVI/VO) etxgain = 3 ; Echolink transmit gain adjustment ; Note: Gain is in db-volts (20logVI/VO) ;eannmode = 1 ; 1 = Say only node number on echolink connects (default = 1) ; 2 = say phonetic call sign only on echolink connects ; 3 = say phonetic call sign and node number on echolink connects
;controlstates = controlstates ; system control state stanza
scheduler = schedule ; scheduler stanza functions = functions ; Repeater Function stanza phone_functions = functions ; Phone Function stanza link_functions = functions ; Link Function stanza
telemetry = telemetry ; Telemetry stanza morse = morse ; Morse stanza wait_times = wait-times ; Wait times stanza
context = radio ; dialing context for phone callerid = "Repeater" <0000000000> ; callerid for phone calls accountcode = RADIO ; account code (optional)
hangtime = 5000 ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms) althangtime = 4000 ; longer squelch tail totime = 180000 ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)
idrecording = |iWA4XYZ ; cording or morse string see http://ohnosec.org/drupal/node/87 idtalkover = |iWA4XYZ ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129 ; See Telemetry section Example: idrecording = rpt/nodenames/1999 idtime = 540000 ; id interval time (in ms) (optional) Default 5 minutes (300000 ms) politeid = 30000 ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)
unlinkedct = ct2 ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none) remotect = ct3 ; remote linked courtesy tone (indicates a remote is in the list of links) linkunkeyct = ct8 ; sent when a transmission received over the link unkeys ;nolocallinkct = 0 ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).
;connpgm = yourconnectprogram ; Disabled. Execute a program you specify on connect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being connected to us (them) ;discpgm = yourdisconnectprogram ; Disabled. Execute a program you specify on disconnect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being disconnected from us (them)
;lnkactenable = 0 ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.
;lnkacttime = 1800 ; Link activity timer time in seconds. ;lnkactmacro = *52 ; Function to execute when link activity timer expires. ;lnkacttimerwarn = 30seconds ; Message to play when the link activity timer has 30 seconds left.
;remote_inact_timeout = ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60) ;remote_timeout = ; Session time out for remote base. Set to 0 to disable. (60 * 60) ;remote_timeout_warning_freq = ; 30 ;remote_timeout_warning = ; (3 * 60)
;nounkeyct = 0 ; Set to a 1 to eliminate courtesy tones and associated delays.
holdofftelem = 0 ; Hold off all telemetry when signal is present on receiver or from connected nodes ; except when an ID needs to be done and there is a signal coming from a connected node.
telemdefault = 0 ; 0 = telemetry output off ; 1 = telemetry output on (default = 1) ; 2 = timed telemetry output on command execution and for a short time thereafter.
telemdynamic = 1 ; 0 = disallow users to change the local telemetry setting with a COP command, ; 1 = Allow users to change the setting with a COP command. (default = 1)
;beaconing = 0 ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)
parrotmode = 0 ; 0 = Parrot Off (default = 0) ; 1 = Parrot On Command ; 2 = Parrot Always ; 3 = Parrot Once by Command
parrottime = 1000 ; Set the amount of time in milliseconds ; to wait before parroting what was received
;rxnotch=1065,40 ; (Optional) Notch a particular frequency for a specified ; b/w. app_rpt must have been compiled with ; the notch option
startup_macro =
; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign ; Point to alternate nodename sound directory
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Need more information on these
;extnodes = extnodes-different ; section in extnodefile containing dynamic node information (optional) ;extnodefile = /foo/nodes ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional) ;extnodefile2 = ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes???? ;nodenames = /foo/names ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames ;archivedir = /tmp ; defines and enables activity recording into specified directory (optional) ;monminblocks = 2048 ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)
; ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set ; ; to support tail messages. They can be omitted otherwise. ;tailmessagetime = 300000 ; Play a tail message every 5 mins ;tailsquashedtime = 30000 ; If squashed by another user, ; ; try again after 30 seconds ;tailmessagelist = msg1,msg2 ; list of messages to be played for tail message
; alt_functions ; ctgroup ; dphone_functions ; idtime ; iobase ; iospeed ; locallist ; mars Remote Base ; memory ; nobusyout ; nodes ; nolocallinkct ; notelemtx ; outxlat ; parrot ; propagate_phonedtmf ; rptnode ; rptinactmacro Macro to execute when inactivity timer expires ; rptinacttime Inactivity timer time in seconds (0 seconds disables feature) ; rxnotch Optional Audio notch ; simplexphonedelay ; tonemacro ; tonezone ; txlimits
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; *** Status Reporting ***
; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org statpost_url = http://stats.allstarlink.org/uhandler ; Status updates
[functions]
; Prefix Functions ; *1 Disconnect Link ; *2 Monitor Link ; *3 Connect Link ; *4 Command Mode ; *5 Macros ; *6 User Functions ; *7 Connection Status/Functions ; *8 User Functions ; *9 User Functions ; *0 User Functions
; *A User Functions ; *B User Functions ; *C User Functions ; *D User Functions
; Mandatory Command Codes ; http://docs.allstarlink.org/drupal/node/91
1 = ilink,1 ; Disconnect specified link 2 = ilink,2 ; Connect specified link -- monitor only 3 = ilink,3 ; Connect specified link -- tranceive 4 = ilink,4 ; Enter command mode on specified link 70 = ilink,5 ; System status 99 = cop,6 ; PTT (phone mode only)
; End Mandatory Command Codes
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Macro Commands 5 = macro
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Autopatch Commands ; Note, This may be a good place for other 2 digit frequently used commands
61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000 ; Autopatch up 62 = autopatchdn ; Autopatch down
; autopatchup can optionally take comma delimited setting=value pairs:
; context = string ; Override default context with "string" ; dialtime = ms ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second) ; farenddisconnect = 1 ; Automatically disconnect when called party hangs up ; noct = 1 ; Don't send repeater courtesy tone during autopatch calls ; quiet = 1 ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Status Commands
; 1 - Force ID (global) ; 2 - Give Time of Day (global) ; 3 - Give software Version (global) ; 4 - Give GPS location info ; 5 - Last (dtmf) user ; 11 - Force ID (local only) ; 12 - Give Time of Day (local only)
721 = status,1 ; Force ID (global) 722 = status,2 ; Give Time of Day (global) 723 = status,3 ; Give software Version (global) 724 = status,4 ; Give GPS location info 725 = status,5 ; Last (dtmf) user 711 = status,11 ; Force ID (local only) 712 = status,12 ; Give Time of Day (local only)
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Link Commands
; 1 - Disconnect specified link ; 2 - Connect specified link -- monitor only ; 3 - Connect specified link -- tranceive ; 4 - Enter command mode on specified link ; 5 - System status ; 6 - Disconnect all links ; 7 - Last Node to Key Up ; 8 - Connect specified link -- local monitor only ; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc. ; 10 - Disconnect all RANGER links (except permalinks) ; 11 - Disconnect a previously permanently connected link ; 12 - Permanently connect specified link -- monitor only ; 13 - Permanently connect specified link -- tranceive ; 15 - Full system status (all nodes) ; 16 - Reconnect links disconnected with "disconnect all links" ; 17 - MDC test (for diag purposes) ; 18 - Permanently Connect specified link -- local monitor only
; ilink commands 1 through 5 are defined in the Mandatory Command section
806 = ilink,6 ; Disconnect all links 807 = ilink,7 ; Last Node to Key Up 808 = ilink,8 ; Connect specified link -- local monitor only 809 = ilink,9,1999,"Testing" ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes 810 = ilink,10 ; Disconnect all RANGER links (except permalinks) 811 = ilink,11 ; Disconnect a previously permanently connected link 812 = ilink,12 ; Permanently connect specified link -- monitor only 813 = ilink,13 ; Permanently connect specified link -- tranceive 815 = ilink,15 ; Full system status (all nodes) 816 = ilink,16 ; Reconnect links disconnected with "disconnect all links" 817 = ilink,17 ; MDC test (for diag purposes) 818 = ilink 18 ; Permanently Connect specified link -- local monitor only
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Control operator (cop) functions. Change these to something other than these codes listed below!
901 = cop,1 ; System warm boot 902 = cop,2 ; System enable 903 = cop,3 ; System disable
904 = cop,4 ; Test tone on/off (toggle) 905 = cop,5 ; Dump system variables on console (debug use only)
907 = cop,7 ; Time out timer enable 908 = cop,8 ; Time out timer disable
909 = cop,9 ; Autopatch enable 910 = cop,10 ; Autopatch disable
911 = cop,11 ; User linking functions enable 912 = cop,12 ; User linking functions disable
913 = cop,13 ; Query system control state 914 = cop,14 ; Set system control state
915 = cop,15 ; Scheduler enable 916 = cop,16 ; Scheduler disable
917 = cop,17 ; User functions enable (time, id, etc) 918 = cop,18 ; User functions disable
919 = cop,19 ; Select alternate hang time (althangtime) 920 = cop,20 ; Select standard hangtime (hangtime)
921 = cop,21 ; Enable Parrot Mode 922 = cop,22 ; Disable Parrot Mode 923 = cop,23 ; Birdbath (Current Parrot Cleanup/Flush)
924 = cop,24 ; Flush all telemetry 925 = cop,25 ; Query last node un-keyed 926 = cop,26 ; Query all nodes keyed/unkeyed 927 = cop,27 ; Reset DAQ minimum on a pin 928 = cop,28 ; Reset DAQ maximum on a pin
930 = cop,30 ; Recall Memory Setting in Attached Xcvr
931 = cop,31 ; Channel Selector for Parallel Programmed Xcvr
932 = cop,32 ; Touchtone pad test: command + Digit string + # to playback all digits pressed
933 = cop,33 ; Local Telemetry Output Enable 934 = cop,34 ; Local Telemetry Output Disable 935 = cop,35 ; Local Telemetry Output on Demand
936 = cop,36 ; Foreign Link Local Output Path Enable 937 = cop,37 ; Foreign Link Local Output Path Disable 938 = cop,38 ; Foreign Link Local Output Path Follows Local Telemetry 939 = cop,39 ; Foreign Link Local Output Path on Demand
942 = cop,42 ; Echolink announce node # only 943 = cop,43 ; Echolink announce node Callsign only 944 = cop,44 ; Echolink announce node # & Callsign
945 = cop,45 ; Link Activity timer enable 945 = cop,46 ; Link Activity timer disable 947 = cop,47 ; Reset "Link Config Changed" Flag
948 = cop,48 ; Send Page Tone (Tone specs separated by parenthesis)
949 = cop,49 ; Disable incoming connections (control state noice) 950 = cop,50 ; Enable incoming connections (control state noicd)
951 = cop,51 ; Enable sleep mode 952 = cop,52 ; Disable sleep mode 953 = cop,53 ; Wake up from sleep 954 = cop,54 ; Go to sleep 955 = cop,55 ; Parrot Once if parrot mode is disabled
956 = cop,56 ; Rx CTCSS Enable 957 = cop,57 ; Rx CTCSS Disable
958 = cop.58 ; Tx CTCSS On Input only Enable 959 = cop,59 ; Tx CTCSS On Input only Disable
960 = cop,60 ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode]) ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F. ; DestID and subcode are only specified for the 'C' type message. ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of ; the radio being called, and the subcodes are as follows: ; Subcode '8205' is Voice Selective Call for Spectra ('Call') ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or ; Astro-Saber('Call') ; Subcode '810D' is Call Alert (like Maxtrac 'CA')
961 = cop,61 ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....) 962 = cop,62 ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)
963 = cop,63 ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR]) 964 = cop,64 ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR]) 965 = cop,65 ; Send POCSAG page (equipped channel types only)
[functions-remote]
0 = remote,1 ; Retrieve Memory 1 = remote,2 ; Set freq. 2 = remote,3 ; Set tx PL tone 3 = remote,4 ; Set rx PL tone 40 = remote,100 ; Rx PL off 41 = remote,101 ; Rx PL on 42 = remote,102 ; Tx PL off 43 = remote,103 ; Tx PL on 44 = remote,104 ; Low Power 45 = remote,105 ; Medium Power 46 = remote,106 ; High Power 711 = remote,107 ; Bump -20 714 = remote,108 ; Bump -100 717 = remote,109 ; Bump -500 713 = remote,110 ; Bump +20 716 = remote,111 ; Bump +100 719 = remote,112 ; Bump +500 721 = remote,113 ; Scan - slow 724 = remote,114 ; Scan - quick 727 = remote,115 ; Scan - fast 723 = remote,116 ; Scan + slow 726 = remote,117 ; Scan + quick 729 = remote,118 ; Scan + fast 79 = remote,119 ; Tune 51 = remote,5 ; Long status query 52 = remote,140 ; Short status query 67 = remote,210 ; Send a * 69 = remote,211 ; Send a # ;91 = remote,99,CALLSIGN,LICENSETAG ; Remote base login. ; Define a different dtmf sequence for each user which is ; authorized to use the remote base to control access to it. ; For examble 9139583=remote,99,WB6NIL,G would grant access to ; the remote base and announce WB6NIL as being logged in. ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to ; the remote base and announce WA6ZFT as being logged in. ; When the remote base is disconnected from the originating node, the ; user will be logged out. The LICENSETAG argument is used to enforce ; tx frequency limits. See [txlimits] below. 85 = cop,6 ; Remote base telephone key
[telemetry]
; Telemetry entries can be shared across all repeaters, or defined for each repeater. ; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape sequence ; ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) ; Single frequencies are created by setting freq1 or freq2 to zero. ; ; |m - Morse escape sequence ; ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ; ; |i - Morse ID escape sequence ; ; Sends Morse code at the ID amplitude and ID frequency as defined in the ; [morse] section. ; ; path/to/sound/file/without/extension ; ; Send the sound if in place of a constructed tone. Do not include the file extension ; Example: ct8 = rpt/bloop ; Example: idrecording = rpt/nodenames/1999
ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2 = |t(660,880,150,2048) ct3 = |t(440,0,150,4096) ct4 = |t(550,0,150,2048) ct5 = |t(660,0,150,2048) ct6 = |t(880,0,150,2048) ct7 = |t(660,440,150,2048) ct8 = |t(700,1100,150,2048) ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0) remotemon = |t(1209,0,50,2048) ; local courtesy tone when receive only remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local courtesy tone when linked Trancieve mode cmdmode = |t(900,903,200,2048) functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048) pfxtone = |t(350,440,30000,3072) patchup = rpt/callproceeding patchdown = rpt/callterminated
; As far as what the numbers mean, ; (000,000,010,000) ; | | | |-------amplitude ; | | |-------------duration ; | |-------------------Tone 2 ; |-------------------------Tone 1
; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude. ; Use it for a delay. Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter) ; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.
; Morse code parameters, these are common to all repeaters.
[morse] speed = 20 ; Approximate speed in WPM frequency = 800 ; Morse Telemetry Frequency amplitude = 4096 ; Morse Telemetry Amplitude idfrequency = 1065 ; Morse ID Frequency idamplitude = 1024 ; Morse ID Amplitude
; ; This section allows wait times for telemetry events to be adjusted ; A section for wait times can be defined for every repeater ;
[wait-times] telemwait = 2000 ; Time to wait before sending most telemetry idwait = 500 ; Time to wait before starting ID unkeywait = 2000 ; Time to wait after unkey before sending CT's and link telemetry calltermwait = 2000 ; Time to wait before announcing "call terminated"
; ; This is where you define your nodes which cam be connected to. ;
[nodes] ; Note, if you are using automatic update for allstar link nodes, ; no allstar link nodes should be defined here. Only place a definition ; for your local nodes, and private (off of allstar link) nodes here.
460310 = radio@....0.1:4569/460310,NONE ; This must be changed to your node number ; and iax port number if not the default ; Memories for remote bases
[memory] ;00 = 146.580,100.0,m ;01 = 147.030,103.5,m+t ;02 = 147.240,103.5,m+t ;03 = 147.765,79.7,m-t ;04 = 146.460,100.0,m ;05 = 146.550,100.0,m
; Place command macros here
[macro] ;1 = *32011# ;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030# ;3 = *32001*32011*32050*32030*32060#
; Data Acquisition configuration
;[daq-list] ;device = device_name1 ;device = device_name2
;Where: device_name1 and device_name2 are stanzas you define in this file
;device = daq-cham-1
; Device name
;[daq-cham-1] ; Defined in [daq-list] ;hwtype = uchameleon ; DAQ hardware type ;devnode = /dev/ttyUSB0 ; DAQ device node (if required) ;1 = inadc ; Pin definition for an ADC channel ;2 = inadc ;3 = inadc ;4 = inadc ;5 = inadc ;6 = inadc ;7 = inadc ;8 = inadc ;9 = inp ; Pin definition for an input with a weak pullup resistor ;10 = inp ;11 = inp ;12 = inp ;13 = in ; Pin definition for an input without a weak pullup resistor ;14 = out ; Pin definition for an output ;15 = out ;16 = out ;17 = out ;18 = out
;[meter-faces]
;face = scale(scalepre,scalediv,scalepost),word/?,... ; ; scalepre = offset to add before dividing with scalediv ; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts). ; scalepost = offset to add after dividing with scalediv ; ;face = range(X-Y:word,X2-Y2:word,...),word/?,... ;face = bit(low-word,high-word),word/?,... ; ; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories, ; or a question mark which is a placeholder for the measured value. ; ; ; Battery voltage 0-20 volts ;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts ; 4 quadrant wind direction ;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,? ; LM34 temperature sensor with 130 deg. F full scale ;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit ; Status poll (non alarmed) ;light = bit(ha/off,ha/on),ha/light,?
;[alarms] ; ;tag = device,pin,node,ignorefirst,func-low,func-hi ; ;tag = a unique name for the alarm ;device = daq device to poll ;pin = the device pin to be monitored ;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it ;node = the node number to execute the function on ;func-low = the DTMF function to execute on a high to low transition ;func-high = the DTMF function to execute on a low to high transition ; ; a '-' as a function name is shorthand for no-operation ; ;door = daq-cham-1,9,1,2017,*7,- ;pwrfail = daq-cham-1,10,0,2017,*911111,- ; ; Control states ; Allow several control operator functions to be changed at once using one command (good for scheduling) ; ;[controlstates] ;statenum = copcmd,[copcmd]... ;0 = rptena,lnkena,apena,totena,ufena,noicd ; Normal operation ;1 = rptena,lnkena,apdis,totdis,ufena,noice ; Net and news operation ;2 = rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only operation
; Scheduler - execute a macro at a given time
[schedule] ;dtmf_function = m h dom mon dow ; ala cron, star is implied ;2 = 00 00 * * * ; at midnight, execute macro 2.
#includeifexists custom/rpt.conf
Analog_Bridge.ini
; Analog_Bridge configuration file. ; This file should be placed in either /etc or it can be ; supplied as a path on the Analog_Bridge command line.
; The best way to think of this file is that there are two main sections, the USRP (analog audio) and ; AMBE_AUDIO (compressed audio). Analog_Bridge will take everything sent to the USRP port and ; encode it for transmission on the AMBE_AUDIO port. The encoder will use the format defined in ambeMode. ; As you might expect, the reverse direction is defined too.
; Analog_Bridge supports include files. More on this later... include = dvsm.macro ; include = asl.macro
; General Section describes settings for Analog_Bridge itself. [GENERAL] logLevel = 2 ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
; Metadata management exportMetadata = true ; Export metadata to USRP partner (transcode setups require this) transferRootDir = /tmp ; Export database files to USRP partner subscriberFile = /var/lib/dvswitch/subscriber_ids.csv ; DMR ID to callsign lookup data
; General vocoder setup information decoderFallBack = true ; Allow software AMBE decoding if a hardware decoder is not found useEmulator = false ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN) emulatorAddress = 127.0.0.1:2470 ; IP address and port of the md380 server
pcmPort = 2222 ; UDP port to send to the WebProxy
; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC) [AMBE_AUDIO] address = 127.0.0.1 ; IP address of xx_Bridge txPort = 31103 ; Transmit TLV frames to partner on this port rxPort = 31100 ; Listen for TLV frames from partner on this port ambeMode = DMR ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format) minTxTimeMS = 2500 ; Analog -> Digital Minimum time in MS for hang delay (0-10000)
; The metadata below is used when ASL is the source since it does not have any concept of digital modes gatewayDmrId = 1112721 ; ID to use when transmitting from Analog_Bridge 7 digit ID repeaterID = 111272123 ; ID of source repeater 7 digit ID plus 2 digit SSID txTg = 31676 ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge txTs = 2 ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge colorCode = 1 ; Color Code to assign DMR frames
; Information for USRP channel driver. This interface uses PCM to transfer audio information ; There are two typical configurations, ASL and Transcode. ASL (AllstarLink) is for analog clients connected ; to a digital network. Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, ; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture. ; When using ASL, this matches the rpt.conf ASL file with a setting like: ; rxchannel = usrp/127.0.0.1:34001:32001 ; When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover). Launch ; each instance with its own ini file. [USRP] address = 127.0.0.1 ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge) txPort = 32001 ; Transmit USRP frames on this port rxPort = 34001 ; Listen for USRP frames on this port usrpAudio = AUDIO_UNITY ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC) usrpGain = 1.10 ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY) usrpAGC = -20,10,100 ; Set the agc threshold (db), slope (db) and decay (ms) tlvAudio = AUDIO_UNITY ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) tlvGain = 0.35 ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
[MACROS]
; Where the macros are ; xxxx=yyyy ; xxxx is the dial string to match ; yyyy is the command line to execute
; xxxx must be preceded by a * ; xxxx can be any string (alphanumeric) ; yyyy is the command to execute ; yyyy will replace xxxx in the dial string ; arguments follow the macro name with a # delimiter
; For example using macro "5678" above would look like: ; *5678#9876
; Which would invoke: ; echo 9876
; Information for DV3000 hardware decoder ; There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware) ; Use top server and port if using AMBEServer ; Use bottom server/port and serial = true if using the DV3000u (thumbdv) ; Did you run AMBETest4.py before using this? [DV3000] address = 127.0.0.1 ; IP address of AMBEServer rxPort = 2460 ; Port of AMBEServer ; address = /dev/ttyUSB0 ; Device of DV3000U on this machine ; baud = 460800 ; Baud rate of the dongle (230400 or 460800) ; serial = true ; Use serial=true f
|
|
|
|
You have 2 channel drivers uncommented:
toggle quoted message
Show quoted text
rxchannel = dahdi/pseudo ; No radio (hub) <--------------------- Comment this out. ; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_1999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP ; rxchannel = Voter/1999 ; RTCM device On 2/14/21 2:34 PM, Steve Siesel
[K4KSA] wrote:
|
|
|
|
Steve Siesel [K4KSA]
After restarting AB and Asterisk….also md3890-emu is running Still no Joy…Here is the latest start of Analog_bridge.log
I: 2021-02-14 19:43:13.761 Analog_Bridge is starting M: 2021-02-14 19:43:13.762 Setting [MACROS] DMR -> /opt/MMDVM_Bridge/dvswitch.sh mode DMR M: 2021-02-14 19:43:13.762 Setting [MACROS] DSTAR -> /opt/MMDVM_Bridge/dvswitch.sh mode DSTAR M: 2021-02-14 19:43:13.762 Setting [MACROS] NXDN -> /opt/MMDVM_Bridge/dvswitch.sh mode NXDN M: 2021-02-14 19:43:13.762 Setting [MACROS] P25 -> /opt/MMDVM_Bridge/dvswitch.sh mode P25 M: 2021-02-14 19:43:13.762 Setting [MACROS] YSF -> /opt/MMDVM_Bridge/dvswitch.sh mode YSF M: 2021-02-14 19:43:13.762 Setting [MACROS] dbupdate -> /opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles M: 2021-02-14 19:43:13.764 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh M: 2021-02-14 19:43:13.765 Setting [] include -> dvsm.macro M: 2021-02-14 19:43:13.766 Setting [GENERAL] logLevel -> 2 M: 2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata -> true M: 2021-02-14 19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp M: 2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv M: 2021-02-14 19:43:13.768 Setting [GENERAL] decoderFallBack -> true M: 2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator -> false M: 2021-02-14 19:43:13.769 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470 M: 2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort -> 2222 M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1 M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103 M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100 M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500 M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721 M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1 M: 2021-02-14 19:43:13.773 Setting [USRP] address -> 127.0.0.1 M: 2021-02-14 19:43:13.773 Setting [USRP] txPort -> 32001 M: 2021-02-14 19:43:13.773 Setting [USRP] rxPort -> 34001 M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY M: 2021-02-14 19:43:13.774 Setting [USRP] usrpGain -> 1.10 M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100 M: 2021-02-14 19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY M: 2021-02-14 19:43:13.775 Setting [USRP] tlvGain -> 0.35 M: 2021-02-14 19:43:13.776 Setting [DV3000] address -> 127.0.0.1 M: 2021-02-14 19:43:13.776 Setting [DV3000] rxPort -> 2460 I: 2021-02-14 19:43:13.777 Open UDP listener on 127.0.0.1:31100 I: 2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001 M: 2021-02-14 19:43:13.777 Connecting to DV3000 hardware...... W: 2021-02-14 19:43:13.871 DV3000 did not reset at 127.0.0.1:2460 W: 2021-02-14 19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset failed) I: 2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850 I: 2021-02-14 19:43:16.073 Default extended metadata <K4KSA> W: 2021-02-14 19:43:16.073 Using software MBE decoder version 1.2.3 W: 2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE vocoder I: 2021-02-14 19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s) 32001 I: 2021-02-14 19:43:16.074 Sending PCM to clients at 127.0.0.1 on port 2222 I: 2021-02-14 19:43:16.074 Starting TLV --> Analog_Bridge (decoder) --> USRP thread I: 2021-02-14 19:43:16.075 Starting USRP --> Analog_Bridge (encoder) -> TLV thread
From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:41 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] ASL<>AB
You have 2 channel drivers uncommented: On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote:
|
|
|
|
Did you fix rpt.conf and did you then restart asterisk?
toggle quoted message
Show quoted text
On 2/14/21 2:46 PM, Steve Siesel
[K4KSA] wrote:
|
|
|
|
Steve Siesel [K4KSA]
Yes…..
From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:50 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] ASL<>AB
Did you fix rpt.conf and did you then restart asterisk? On 2/14/21 2:46 PM, Steve Siesel [K4KSA] wrote:
|
|
|
|
Is chan_usrp enabled in modules.conf?
toggle quoted message
Show quoted text
On 2/14/21 2:50 PM, Steve Siesel
[K4KSA] wrote:
|
|
|
|
Steve Siesel [K4KSA]
It is now working…Long hangtime I think I will change Hangtime to 20
From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:51 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] ASL<>AB
Is chan_usrp enabled in modules.conf? On 2/14/21 2:50 PM, Steve Siesel [K4KSA] wrote:
|
|
|
|
I suggest you use these values:
toggle quoted message
Show quoted text
duplex = 0 ; 0 = Half duplex with no telemetry tones or hang time. Ah, but Allison STILL talks! hangtime = 0 ; squelch tail hang time 0 althangtime = 0 ; longer squelch tail hang time 0 holdofftelem = 1 ; Hold off all telemetry when signal is present on receiver or from connected nodes ; except when an ID needs to be done and there is a signal coming from a connected node. telemdefault = 0 ; 0 = telemetry output off. Don't send Allison to DMR !!!!!!!!!!!!!!!!! Trust me. telemdynamic = 0 ; 0 = disallow users to change the local telemetry setting with a COP command, linktolink = no ; disables forcing physical half-duplex operation of main repeater while ; still keeping half-duplex semantics (optional) nounkeyct = 1 ; Set to a 1 to eliminate courtesy tones and associated delays. totime = 180000 ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms) ; idrecording = |ie ; id recording or morse string see http://ohnosec.org/drupal/node/87 ; idtalkover = |ie ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129 On 2/14/21 2:56 PM, Steve Siesel
[K4KSA] wrote:
|