ASL<>AB


Steve Siesel [K4KSA]
 

Thanks…All seems good now…One last question for today..( I Hope!) What would be the apt command to install a second instance of DVSwitch server (for broadcastify purpsoses) to lets say  to /home/k4ksa?

 

Steve

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:59 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

I suggest you use these values:

duplex = 0                ; 0 = Half duplex with no telemetry tones or hang time. Ah, but Allison STILL talks!

hangtime = 0                ; squelch tail hang time 0
althangtime = 0                ; longer squelch tail hang time 0

holdofftelem = 1            ; Hold off all telemetry when signal is present on receiver or from connected nodes
                    ; except when an ID needs to be done and there is a signal coming from a connected node.

telemdefault = 0            ; 0 = telemetry output off. Don't send Allison to DMR !!!!!!!!!!!!!!!!! Trust me.

telemdynamic = 0            ; 0 = disallow users to change the local telemetry setting with a COP command,

linktolink = no                ; disables forcing physical half-duplex operation of main repeater while
                    ; still keeping half-duplex semantics (optional)

nounkeyct = 1                ; Set to a 1 to eliminate courtesy tones and associated delays.

totime = 180000                ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

; idrecording = |ie            ; id recording or morse string see http://ohnosec.org/drupal/node/87
; idtalkover = |ie            ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129

On 2/14/21 2:56 PM, Steve Siesel [K4KSA] wrote:

It is now working…Long hangtime I think I will change Hangtime to 20

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:51 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

Is chan_usrp enabled in modules.conf?

On 2/14/21 2:50 PM, Steve Siesel [K4KSA] wrote:

Yes…..

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:50 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

Did you fix rpt.conf and did you then restart asterisk?

On 2/14/21 2:46 PM, Steve Siesel [K4KSA] wrote:

After restarting AB and Asterisk….also md3890-emu is running

Still no Joy…Here is the latest start of Analog_bridge.log

 

 

I: 2021-02-14 19:43:13.761 Analog_Bridge is starting

M: 2021-02-14 19:43:13.762 Setting [MACROS] DMR -> /opt/MMDVM_Bridge/dvswitch.sh mode DMR

M: 2021-02-14 19:43:13.762 Setting [MACROS] DSTAR -> /opt/MMDVM_Bridge/dvswitch.sh mode DSTAR

M: 2021-02-14 19:43:13.762 Setting [MACROS] NXDN -> /opt/MMDVM_Bridge/dvswitch.sh mode NXDN

M: 2021-02-14 19:43:13.762 Setting [MACROS] P25 -> /opt/MMDVM_Bridge/dvswitch.sh mode P25

M: 2021-02-14 19:43:13.762 Setting [MACROS] YSF -> /opt/MMDVM_Bridge/dvswitch.sh mode YSF

M: 2021-02-14 19:43:13.762 Setting [MACROS] dbupdate -> /opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles

M: 2021-02-14 19:43:13.764 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh

M: 2021-02-14 19:43:13.765 Setting [] include -> dvsm.macro

M: 2021-02-14 19:43:13.766 Setting [GENERAL] logLevel -> 2

M: 2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata -> true

M: 2021-02-14 19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp

M: 2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv

M: 2021-02-14 19:43:13.768 Setting [GENERAL] decoderFallBack -> true

M: 2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator -> false

M: 2021-02-14 19:43:13.769 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470

M: 2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort -> 2222

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1

M: 2021-02-14 19:43:13.773 Setting [USRP] address -> 127.0.0.1

M: 2021-02-14 19:43:13.773 Setting [USRP] txPort -> 32001

M: 2021-02-14 19:43:13.773 Setting [USRP] rxPort -> 34001

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpGain -> 1.10

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvGain -> 0.35

M: 2021-02-14 19:43:13.776 Setting [DV3000] address -> 127.0.0.1

M: 2021-02-14 19:43:13.776 Setting [DV3000] rxPort -> 2460

I: 2021-02-14 19:43:13.777 Open UDP listener on 127.0.0.1:31100

I: 2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001

M: 2021-02-14 19:43:13.777 Connecting to DV3000 hardware......

W: 2021-02-14 19:43:13.871 DV3000 did not reset at 127.0.0.1:2460

W: 2021-02-14 19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset failed)

I: 2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850

I: 2021-02-14 19:43:16.073 Default extended metadata <K4KSA>

W: 2021-02-14 19:43:16.073 Using software MBE decoder version 1.2.3

W: 2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE vocoder

I: 2021-02-14 19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s) 32001

I: 2021-02-14 19:43:16.074 Sending PCM to  clients at 127.0.0.1 on port 2222

I: 2021-02-14 19:43:16.074 Starting TLV --> Analog_Bridge (decoder) --> USRP thread

I: 2021-02-14 19:43:16.075 Starting USRP --> Analog_Bridge (encoder) -> TLV thread

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:41 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

You have 2 channel drivers uncommented:

rxchannel = dahdi/pseudo                ; No radio (hub) <--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB
; rxchannel = Pi/1                      ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999            ; USBRadio (DSP)
; rxchannel = Dahdi/1                   ; PCI Quad card
; rxchannel = Beagle/1                  ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999                ; RTCM device

On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote:

Can you look at this as well…..

 

I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that.

 

Steve

 

 

; Your Repeater

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

[460310]                                        ; Change this to your assigned node number

 

                                        ; Must also be enabled in modules.conf

                                        ; Rx audio/signalling channel. Choose ONLY 1 per node stanza

 

                                        ; Enable the selected channel driver in modules.conf !!!

rxchannel = dahdi/pseudo                ; No radio (hub)

; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB

; rxchannel = Pi/1                      ; Raspberry Pi PiTA

; rxchannel = Radio/usb_1999            ; USBRadio (DSP)

; rxchannel = Dahdi/1                   ; PCI Quad card

; rxchannel = Beagle/1                  ; BeagleBoard

rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP

; rxchannel = Voter/1999                ; RTCM device

 

 

duplex = 1                              ; 0 = Half duplex with no telemetry tones or hang time.

                                        ;     Special Case: Full duplex if linktolink is set to yes.

                                        ;     This mode is preferred when interfacing with an external multiport repeater controller.

                                        ;     Comment out idrecording and idtalkover to suppress IDs also

                                        ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio.

                                        ;     This mode is preferred when interfacing a simplex node.

                                        ; 2 = Full Duplex with telemetry tones and hang time.

                                        ;     This mode is preferred when interfacing a repeater.

                                        ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio.

                                        ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.

 

linktolink = no                         ; disables forcing physical half-duplex operation of main repeater while

                                        ; still keeping half-duplex semantics (optional)

 

linkmongain = 0                         ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received.

                                        ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db.

                                        ; If linkmongain set to a positive number monitored audio will increase by the set amount in db.

                                        ; The value of linkmongain is in db. The default value is 0 db.

 

erxgain = -3                            ; Echolink receive gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

etxgain = 3                             ; Echolink transmit gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

;eannmode = 1                           ; 1 = Say only node number on echolink connects (default = 1)

                                        ; 2 = say phonetic call sign only on echolink connects

                                        ; 3 = say phonetic call sign and node number on echolink connects

 

;controlstates = controlstates          ; system control state stanza

 

scheduler = schedule                    ; scheduler stanza

functions = functions                   ; Repeater Function stanza

phone_functions = functions             ; Phone Function stanza

link_functions = functions              ; Link Function stanza

 

telemetry = telemetry                   ; Telemetry stanza

morse = morse                           ; Morse stanza

wait_times = wait-times                 ; Wait times stanza

 

context = radio                         ; dialing context for phone

callerid = "Repeater" <0000000000>      ; callerid for phone calls

accountcode = RADIO                     ; account code (optional)

 

hangtime = 5000                         ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms)

althangtime = 4000                      ; longer squelch tail

totime = 180000                         ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

 

idrecording = |iWA4XYZ                  ; cording or morse string see http://ohnosec.org/drupal/node/87

idtalkover = |iWA4XYZ                   ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129

                                        ; See Telemetry section Example: idrecording = rpt/nodenames/1999

idtime = 540000                         ; id interval time (in ms) (optional) Default 5 minutes (300000 ms)

politeid = 30000                        ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)

 

unlinkedct = ct2                        ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none)

remotect = ct3                          ; remote linked courtesy tone (indicates a remote is in the list of links)

linkunkeyct = ct8                       ; sent when a transmission received over the link unkeys

;nolocallinkct = 0                      ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).

 

;connpgm = yourconnectprogram           ; Disabled. Execute a program you specify on connect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being connected to us (them)

;discpgm = yourdisconnectprogram        ; Disabled. Execute a program you specify on disconnect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being disconnected from us (them)

 

;lnkactenable = 0                       ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.

 

;lnkacttime = 1800                      ; Link activity timer time in seconds.

;lnkactmacro = *52                      ; Function to execute when link activity timer expires.

;lnkacttimerwarn = 30seconds            ; Message to play when the link activity timer has 30 seconds left.

 

;remote_inact_timeout =                 ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60)

;remote_timeout =                       ; Session time out for remote base. Set to 0 to disable. (60 * 60)

;remote_timeout_warning_freq =          ; 30

;remote_timeout_warning =               ; (3 * 60)

 

;nounkeyct = 0                          ; Set to a 1 to eliminate courtesy tones and associated delays.

 

holdofftelem = 0                        ; Hold off all telemetry when signal is present on receiver or from connected nodes

                                        ; except when an ID needs to be done and there is a signal coming from a connected node.

 

telemdefault = 0                        ; 0 = telemetry output off

                                        ; 1 = telemetry output on (default = 1)

                                        ; 2 = timed telemetry output on command execution and for a short time thereafter.

 

telemdynamic = 1                        ; 0 = disallow users to change the local telemetry setting with a COP command,

                                        ; 1 = Allow users to change the setting with a COP command. (default = 1)

 

;beaconing = 0                          ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)

 

parrotmode = 0                          ; 0 = Parrot Off (default = 0)

                                        ; 1 = Parrot On Command

                                        ; 2 = Parrot Always

                                        ; 3 = Parrot Once by Command

 

parrottime = 1000                       ; Set the amount of time in milliseconds

                                        ; to wait before parroting what was received

 

;rxnotch=1065,40                        ; (Optional) Notch a particular frequency for a specified

                                        ; b/w. app_rpt must have been compiled with

                                        ; the notch option

 

startup_macro =

 

; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign   ; Point to alternate nodename sound directory

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Need more information on these

 

;extnodes = extnodes-different  ; section in extnodefile containing dynamic node information (optional)

;extnodefile = /foo/nodes       ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional)

;extnodefile2 =                 ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes????

;nodenames = /foo/names         ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames

;archivedir = /tmp              ; defines and enables activity recording into specified directory (optional)

;monminblocks = 2048            ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)

 

;                               ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set

;                               ; to support tail messages. They can be omitted otherwise.

;tailmessagetime = 300000       ; Play a tail message every 5 mins

;tailsquashedtime = 30000       ; If squashed by another user,

;                               ; try again after 30 seconds

;tailmessagelist = msg1,msg2    ; list of messages to be played for tail message

 

; alt_functions

; ctgroup

; dphone_functions

; idtime

; iobase

; iospeed

; locallist

; mars          Remote Base

; memory

; nobusyout

; nodes

; nolocallinkct

; notelemtx

; outxlat

; parrot

; propagate_phonedtmf

; rptnode

; rptinactmacro  Macro to execute when inactivity timer expires

; rptinacttime   Inactivity timer time in seconds  (0 seconds disables feature)

; rxnotch       Optional Audio notch

; simplexphonedelay

; tonemacro

; tonezone

; txlimits

 

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

 

; *** Status Reporting ***

 

; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org

statpost_url = http://stats.allstarlink.org/uhandler ; Status updates

 

[functions]

 

; Prefix        Functions

; *1            Disconnect Link

; *2            Monitor Link

; *3            Connect Link

; *4            Command Mode

; *5            Macros

; *6            User Functions

; *7            Connection Status/Functions

; *8            User Functions

; *9            User Functions

; *0            User Functions

 

; *A            User Functions

; *B            User Functions

; *C            User Functions

; *D            User Functions

 

 

; Mandatory Command Codes

; http://docs.allstarlink.org/drupal/node/91

 

1 = ilink,1             ; Disconnect specified link

2 = ilink,2             ; Connect specified link -- monitor only

3 = ilink,3             ; Connect specified link -- tranceive

4 = ilink,4             ; Enter command mode on specified link

70 = ilink,5            ; System status

99 = cop,6              ; PTT (phone mode only)

 

; End Mandatory Command Codes

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Macro Commands

5 = macro

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Autopatch Commands

; Note, This may be a good place for other 2 digit frequently used commands

 

61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000  ; Autopatch up

62 = autopatchdn                                                 ; Autopatch down

 

; autopatchup can optionally take comma delimited setting=value pairs:

 

; context = string              ; Override default context with "string"

; dialtime = ms                 ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second)

; farenddisconnect = 1          ; Automatically disconnect when called party hangs up

; noct = 1                      ; Don't send repeater courtesy tone during autopatch calls

; quiet = 1                     ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up

                                ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Status Commands

 

; 1 - Force ID (global)

; 2 - Give Time of Day (global)

; 3 - Give software Version (global)

; 4 - Give GPS location info

; 5 - Last (dtmf) user

; 11 - Force ID (local only)

; 12 - Give Time of Day (local only)

 

721 = status,1          ; Force ID (global)

722 = status,2          ; Give Time of Day (global)

723 = status,3          ; Give software Version (global)

724 = status,4          ; Give GPS location info

725 = status,5          ; Last (dtmf) user

711 = status,11         ; Force ID (local only)

712 = status,12         ; Give Time of Day (local only)

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Link Commands

 

; 1 - Disconnect specified link

; 2 - Connect specified link -- monitor only

; 3 - Connect specified link -- tranceive

; 4 - Enter command mode on specified link

; 5 - System status

; 6 - Disconnect all links

; 7 - Last Node to Key Up

; 8 - Connect specified link -- local monitor only

; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.

; 10 - Disconnect all RANGER links (except permalinks)

; 11 - Disconnect a previously permanently connected link

; 12 - Permanently connect specified link -- monitor only

; 13 - Permanently connect specified link -- tranceive

; 15 - Full system status (all nodes)

; 16 - Reconnect links disconnected with "disconnect all links"

; 17 - MDC test (for diag purposes)

; 18 - Permanently Connect specified link -- local monitor only

 

; ilink commands 1 through 5 are defined in the Mandatory Command section

 

806 = ilink,6                   ; Disconnect all links

807 = ilink,7                   ; Last Node to Key Up

808 = ilink,8                   ; Connect specified link -- local monitor only

809 = ilink,9,1999,"Testing"    ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes

810 = ilink,10                  ; Disconnect all RANGER links (except permalinks)

811 = ilink,11                  ; Disconnect a previously permanently connected link

812 = ilink,12                  ; Permanently connect specified link -- monitor only

813 = ilink,13                  ; Permanently connect specified link -- tranceive

815 = ilink,15                  ; Full system status (all nodes)

816 = ilink,16                  ; Reconnect links disconnected with "disconnect all links"

817 = ilink,17                  ; MDC test (for diag purposes)

818 = ilink 18                  ; Permanently Connect specified link -- local monitor only

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Control operator (cop) functions. Change these to something other than these codes listed below!

 

901 = cop,1                   ��         ; System warm boot

902 = cop,2                             ; System enable

903 = cop,3                             ; System disable

 

904 = cop,4                             ; Test tone on/off (toggle)

905 = cop,5                             ; Dump system variables on console (debug use only)

 

907 = cop,7                             ; Time out timer enable

908 = cop,8                             ; Time out timer disable

 

909 = cop,9                             ; Autopatch enable

910 = cop,10                            ; Autopatch disable

 

911 = cop,11                            ; User linking functions enable

912 = cop,12                            ; User linking functions disable

 

913 = cop,13                            ; Query system control state

914 = cop,14                            ; Set system control state

 

915 = cop,15                            ; Scheduler enable

916 = cop,16                            ; Scheduler disable

 

917 = cop,17                            ; User functions enable (time, id, etc)

918 = cop,18                            ; User functions disable

 

919 = cop,19                            ; Select alternate hang time (althangtime)

920 = cop,20                            ; Select standard hangtime (hangtime)

 

921 = cop,21                            ; Enable Parrot Mode

922 = cop,22                            ; Disable Parrot Mode

923 = cop,23                            ; Birdbath (Current Parrot Cleanup/Flush)

 

924 = cop,24                            ; Flush all telemetry

925 = cop,25                            ; Query last node un-keyed

926 = cop,26                            ; Query all nodes keyed/unkeyed

927 = cop,27                            ; Reset DAQ minimum on a pin

928 = cop,28                            ; Reset DAQ maximum on a pin

 

930 = cop,30                            ; Recall Memory Setting in Attached Xcvr

 

931 = cop,31                            ; Channel Selector for Parallel Programmed Xcvr

 

932 = cop,32                            ; Touchtone pad test: command + Digit string + # to playback all digits pressed

 

933 = cop,33                            ; Local Telemetry Output Enable

934 = cop,34                            ; Local Telemetry Output Disable

935 = cop,35                            ; Local Telemetry Output on Demand

 

936 = cop,36                            ; Foreign Link Local Output Path Enable

937 = cop,37                            ; Foreign Link Local Output Path Disable

938 = cop,38                            ; Foreign Link Local Output Path Follows Local Telemetry

939 = cop,39                            ; Foreign Link Local Output Path on Demand

 

942 = cop,42                            ; Echolink announce node # only

943 = cop,43                            ; Echolink announce node Callsign only

944 = cop,44                            ; Echolink announce node # & Callsign

 

945 = cop,45                            ; Link Activity timer enable

945 = cop,46                            ; Link Activity timer disable

947 = cop,47                            ; Reset "Link Config Changed" Flag

 

948 = cop,48                            ; Send Page Tone (Tone specs separated by parenthesis)

 

949 = cop,49                            ; Disable incoming connections (control state noice)

950 = cop,50                            ; Enable incoming connections (control state noicd)

 

951 = cop,51                            ; Enable sleep mode

952 = cop,52                            ; Disable sleep mode

953 = cop,53                            ; Wake up from sleep

954 = cop,54                            ; Go to sleep

955 = cop,55                            ; Parrot Once if parrot mode is disabled

 

956 = cop,56                            ; Rx CTCSS Enable

957 = cop,57                            ; Rx CTCSS Disable

 

958 = cop.58                            ; Tx CTCSS On Input only Enable

959 = cop,59                            ; Tx CTCSS On Input only Disable

 

960 = cop,60                            ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])

                                        ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call

                                        ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.

                                        ; DestID and subcode are only specified for  the 'C' type message.

                                        ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of

                                        ; the radio being called, and the subcodes are as follows:

                                        ; Subcode '8205' is Voice Selective Call for Spectra ('Call')

                                        ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or

                                        ; Astro-Saber('Call')

                                        ; Subcode '810D' is Call Alert (like Maxtrac 'CA')

 

961 = cop,61                            ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)

962 = cop,62                            ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)

 

963 = cop,63                            ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])

964 = cop,64                            ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])

965 = cop,65                            ; Send POCSAG page (equipped channel types only)

 

[functions-remote]

 

0 = remote,1                            ; Retrieve Memory

1 = remote,2                            ; Set freq.

2 = remote,3                            ; Set tx PL tone

3 = remote,4                            ; Set rx PL tone

40 = remote,100                         ; Rx PL off

41 = remote,101                         ; Rx PL on

42 = remote,102                         ; Tx PL off

43 = remote,103                         ; Tx PL on

44 = remote,104                         ; Low Power

45 = remote,105                         ; Medium Power

46 = remote,106                         ; High Power

711 = remote,107                        ; Bump -20

714 = remote,108                        ; Bump -100

717 = remote,109                        ; Bump -500

713 = remote,110                        ; Bump +20

716 = remote,111                        ; Bump +100

719 = remote,112                        ; Bump +500

721 = remote,113                        ; Scan - slow

724 = remote,114                        ; Scan - quick

727 = remote,115                        ; Scan - fast

723 = remote,116                        ; Scan + slow

726 = remote,117                        ; Scan + quick

729 = remote,118                        ; Scan + fast

79 = remote,119                         ; Tune

51 = remote,5                           ; Long status query

52 = remote,140                         ; Short status query

67 = remote,210                         ; Send a *

69 = remote,211                         ; Send a #

;91 = remote,99,CALLSIGN,LICENSETAG     ; Remote base login.

                                        ; Define a different dtmf sequence for each user which is

                                        ; authorized to use the remote base to control access to it.

                                        ; For examble 9139583=remote,99,WB6NIL,G would grant access to

                                        ; the remote base and announce WB6NIL as being logged in.

                                        ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to

                                        ; the remote base and announce WA6ZFT as being logged in.

                                        ; When the remote base is disconnected from the originating node, the

                                        ; user will be logged out. The LICENSETAG argument is used to enforce

                                        ; tx frequency limits. See [txlimits] below.

85 = cop,6                              ; Remote base telephone key

 

 

[telemetry]

 

; Telemetry entries can be shared across all repeaters, or defined for each repeater.

; Can be a tone sequence, morse string, or a file

;

; |t - Tone escape sequence

;

; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)

; Single frequencies are created by setting freq1 or freq2 to zero.

;

; |m - Morse escape sequence

;

; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the

; [morse] section.

;

; Follow with an alphanumeric string

;

; |i - Morse ID escape sequence

;

; Sends Morse code at the ID amplitude and ID frequency as defined in the

; [morse] section.

;

; path/to/sound/file/without/extension

;

; Send the sound if in place of a constructed tone. Do not include the file extension

; Example: ct8 = rpt/bloop

; Example: idrecording = rpt/nodenames/1999

 

ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)

ct2 = |t(660,880,150,2048)

ct3 = |t(440,0,150,4096)

ct4 = |t(550,0,150,2048)

ct5 = |t(660,0,150,2048)

ct6 = |t(880,0,150,2048)

ct7 = |t(660,440,150,2048)

ct8 = |t(700,1100,150,2048)

ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)

remotemon = |t(1209,0,50,2048)                                  ; local courtesy tone when receive only

remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000)         ; local courtesy tone when linked Trancieve mode

cmdmode = |t(900,903,200,2048)

functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)

remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)

pfxtone = |t(350,440,30000,3072)

patchup = rpt/callproceeding

patchdown = rpt/callterminated

 

; As far as what the numbers mean,

; (000,000,010,000)

;   |   |   |   |-------amplitude

;   |   |   |-------------duration

;   |   |-------------------Tone 2

;   |-------------------------Tone 1

 

; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.

; Use it for a delay.  Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter)

; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.

 

; Morse code parameters, these are common to all repeaters.

 

[morse]

speed = 20                              ; Approximate speed in WPM

frequency = 800                         ; Morse Telemetry Frequency

amplitude = 4096                        ; Morse Telemetry Amplitude

idfrequency = 1065                      ; Morse ID Frequency

idamplitude = 1024                      ; Morse ID Amplitude

 

;

; This section allows wait times for telemetry events to be adjusted

; A section for wait times can be defined for every repeater

;

 

[wait-times]

telemwait = 2000                        ; Time to wait before sending most telemetry

idwait = 500                            ; Time to wait before starting ID

unkeywait = 2000                        ; Time to wait after unkey before sending CT's and link telemetry

calltermwait = 2000                     ; Time to wait before announcing "call terminated"

 

;

; This is where you define your nodes which cam be connected to.

;

 

[nodes]

; Note, if you are using automatic update for allstar link nodes,

; no allstar link nodes should be defined here. Only place a definition

; for your local nodes, and private (off of allstar link) nodes here.

 

460310 = radio@....0.1:4569/460310,NONE       ; This must be changed to your node number

                                        ; and iax port number if not the default

; Memories for remote bases

 

[memory]

;00 = 146.580,100.0,m

;01 = 147.030,103.5,m+t

;02 = 147.240,103.5,m+t

;03 = 147.765,79.7,m-t

;04 = 146.460,100.0,m

;05 = 146.550,100.0,m

 

; Place command macros here

 

[macro]

;1 = *32011#

;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#

;3 = *32001*32011*32050*32030*32060#

 

 

; Data Acquisition configuration

 

;[daq-list]

;device = device_name1

;device = device_name2

 

;Where: device_name1 and device_name2 are stanzas you define in this file

 

;device = daq-cham-1

 

; Device name

 

;[daq-cham-1]                           ; Defined in [daq-list]

;hwtype = uchameleon                    ; DAQ hardware type

;devnode = /dev/ttyUSB0                 ; DAQ device node (if required)

;1 = inadc                              ; Pin definition for an ADC channel

;2 = inadc

;3 = inadc

;4 = inadc

;5 = inadc

;6 = inadc

;7 = inadc

;8 = inadc

;9 = inp                                ; Pin definition for an input with a weak pullup resistor

;10 = inp

;11 = inp

;12 = inp

;13 = in                                ; Pin definition for an input without a weak pullup resistor

;14 = out                               ; Pin definition for an output

;15 = out

;16 = out

;17 = out

;18 = out

 

;[meter-faces]

 

;face = scale(scalepre,scalediv,scalepost),word/?,...

;

; scalepre = offset to add before dividing with scalediv

; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts).

; scalepost = offset to add after dividing with scalediv

;

;face = range(X-Y:word,X2-Y2:word,...),word/?,...

;face = bit(low-word,high-word),word/?,...

;

; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories,

; or a question mark which is  a placeholder for the measured value.

;

;

; Battery voltage 0-20 volts

;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts

; 4 quadrant wind direction

;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?

; LM34 temperature sensor with 130 deg. F full scale

;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit

; Status poll (non alarmed)

;light = bit(ha/off,ha/on),ha/light,?

 

;[alarms]

;

;tag = device,pin,node,ignorefirst,func-low,func-hi

;

;tag = a unique name for the alarm

;device = daq device to poll

;pin = the device pin to be monitored

;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it

;node = the node number to execute the function on

;func-low = the DTMF function to execute on a high to low transition

;func-high = the DTMF function to execute on a low to high transition

;

; a  '-' as a function name is shorthand for no-operation

;

;door = daq-cham-1,9,1,2017,*7,-

;pwrfail = daq-cham-1,10,0,2017,*911111,-

;

; Control states

; Allow several control operator functions to be changed at once using one command (good for scheduling)

;

;[controlstates]

;statenum = copcmd,[copcmd]...

;0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation

;1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation

;2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation

 

; Scheduler - execute a macro at a given time

 

[schedule]

;dtmf_function =  m h dom mon dow  ; ala cron, star is implied

;2 = 00 00 * * *   ; at midnight, execute macro 2.

 

#includeifexists custom/rpt.conf

 

 

 

 

Analog_Bridge.ini

 

 

; Analog_Bridge configuration file.

;   This file should be placed in either /etc or it can be

;   supplied as a path on the Analog_Bridge command line.

 

; The best way to think of this file is that there are two main sections, the USRP (analog audio) and

; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and

; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.

; As you might expect, the reverse direction is defined too.

 

; Analog_Bridge supports include files. More on this later...

include = dvsm.macro

; include = asl.macro

 

; General Section describes settings for Analog_Bridge itself.

[GENERAL]

logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal

 

; Metadata management

exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)

transferRootDir = /tmp                  ; Export database files to USRP partner

subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data

 

; General vocoder setup information

decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found

useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)

emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server

 

pcmPort = 2222                          ; UDP port to send to the WebProxy

 

; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)

[AMBE_AUDIO]

address = 127.0.0.1                     ; IP address of xx_Bridge

txPort = 31103                          ; Transmit TLV frames to partner on this port

rxPort = 31100                          ; Listen for TLV frames from partner on this port

ambeMode = DMR                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)

minTxTimeMS = 2500                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)

 

; The metadata below is used when ASL is the source since it does not have any concept of digital modes

gatewayDmrId = 1112721                  ; ID to use when transmitting from Analog_Bridge 7 digit ID

repeaterID = 111272123                  ; ID of source repeater 7 digit ID plus 2 digit SSID

txTg = 31676                               ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge

txTs = 2                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge

colorCode = 1                           ; Color Code to assign DMR frames

 

; Information for USRP channel driver.  This interface uses PCM to transfer audio information

; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected

; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself,

; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.

;   When using ASL, this matches the rpt.conf ASL file with a setting like:

;   rxchannel = usrp/127.0.0.1:34001:32001

;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch

;   each instance with its own ini file.

[USRP]

address = 127.0.0.1                     ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge)

txPort = 32001                          ; Transmit USRP frames on this port

rxPort = 34001                          ; Listen for USRP frames on this port

usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)

usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)

tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)

tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

 

[MACROS]

 

; Where the macros are

; xxxx=yyyy

; xxxx is the dial string to match

; yyyy is the command line to execute

 

; xxxx must be preceded by a *

; xxxx can be any string (alphanumeric)

; yyyy is the command to execute

; yyyy will replace xxxx in the dial string

; arguments follow the macro name with a # delimiter

 

; For example using macro "5678" above would look like:

; *5678#9876

 

; Which would invoke:

; echo 9876

 

; Information for DV3000 hardware decoder

;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)

;   Use top server and port if using AMBEServer

;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)

;   Did you run AMBETest4.py before using this?

[DV3000]

address = 127.0.0.1                   ; IP address of AMBEServer

rxPort = 2460                         ; Port of AMBEServer

; address = /dev/ttyUSB0              ; Device of DV3000U on this machine

; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)

; serial = true                       ; Use serial=true f

 

 

 

 

 

 

 

 


Steve N4IRS
 

I suggest you use these values:

duplex = 0                ; 0 = Half duplex with no telemetry tones or hang time. Ah, but Allison STILL talks!

hangtime = 0                ; squelch tail hang time 0
althangtime = 0                ; longer squelch tail hang time 0

holdofftelem = 1            ; Hold off all telemetry when signal is present on receiver or from connected nodes
                    ; except when an ID needs to be done and there is a signal coming from a connected node.

telemdefault = 0            ; 0 = telemetry output off. Don't send Allison to DMR !!!!!!!!!!!!!!!!! Trust me.

telemdynamic = 0            ; 0 = disallow users to change the local telemetry setting with a COP command,

linktolink = no                ; disables forcing physical half-duplex operation of main repeater while
                    ; still keeping half-duplex semantics (optional)

nounkeyct = 1                ; Set to a 1 to eliminate courtesy tones and associated delays.

totime = 180000                ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

; idrecording = |ie            ; id recording or morse string see http://ohnosec.org/drupal/node/87
; idtalkover = |ie            ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129


On 2/14/21 2:56 PM, Steve Siesel [K4KSA] wrote:

It is now working…Long hangtime I think I will change Hangtime to 20

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:51 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

Is chan_usrp enabled in modules.conf?

On 2/14/21 2:50 PM, Steve Siesel [K4KSA] wrote:

Yes…..

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:50 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

Did you fix rpt.conf and did you then restart asterisk?

On 2/14/21 2:46 PM, Steve Siesel [K4KSA] wrote:

After restarting AB and Asterisk….also md3890-emu is running

Still no Joy…Here is the latest start of Analog_bridge.log

 

 

I: 2021-02-14 19:43:13.761 Analog_Bridge is starting

M: 2021-02-14 19:43:13.762 Setting [MACROS] DMR -> /opt/MMDVM_Bridge/dvswitch.sh mode DMR

M: 2021-02-14 19:43:13.762 Setting [MACROS] DSTAR -> /opt/MMDVM_Bridge/dvswitch.sh mode DSTAR

M: 2021-02-14 19:43:13.762 Setting [MACROS] NXDN -> /opt/MMDVM_Bridge/dvswitch.sh mode NXDN

M: 2021-02-14 19:43:13.762 Setting [MACROS] P25 -> /opt/MMDVM_Bridge/dvswitch.sh mode P25

M: 2021-02-14 19:43:13.762 Setting [MACROS] YSF -> /opt/MMDVM_Bridge/dvswitch.sh mode YSF

M: 2021-02-14 19:43:13.762 Setting [MACROS] dbupdate -> /opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles

M: 2021-02-14 19:43:13.764 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh

M: 2021-02-14 19:43:13.765 Setting [] include -> dvsm.macro

M: 2021-02-14 19:43:13.766 Setting [GENERAL] logLevel -> 2

M: 2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata -> true

M: 2021-02-14 19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp

M: 2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv

M: 2021-02-14 19:43:13.768 Setting [GENERAL] decoderFallBack -> true

M: 2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator -> false

M: 2021-02-14 19:43:13.769 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470

M: 2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort -> 2222

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1

M: 2021-02-14 19:43:13.773 Setting [USRP] address -> 127.0.0.1

M: 2021-02-14 19:43:13.773 Setting [USRP] txPort -> 32001

M: 2021-02-14 19:43:13.773 Setting [USRP] rxPort -> 34001

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpGain -> 1.10

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvGain -> 0.35

M: 2021-02-14 19:43:13.776 Setting [DV3000] address -> 127.0.0.1

M: 2021-02-14 19:43:13.776 Setting [DV3000] rxPort -> 2460

I: 2021-02-14 19:43:13.777 Open UDP listener on 127.0.0.1:31100

I: 2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001

M: 2021-02-14 19:43:13.777 Connecting to DV3000 hardware......

W: 2021-02-14 19:43:13.871 DV3000 did not reset at 127.0.0.1:2460

W: 2021-02-14 19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset failed)

I: 2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850

I: 2021-02-14 19:43:16.073 Default extended metadata <K4KSA>

W: 2021-02-14 19:43:16.073 Using software MBE decoder version 1.2.3

W: 2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE vocoder

I: 2021-02-14 19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s) 32001

I: 2021-02-14 19:43:16.074 Sending PCM to  clients at 127.0.0.1 on port 2222

I: 2021-02-14 19:43:16.074 Starting TLV --> Analog_Bridge (decoder) --> USRP thread

I: 2021-02-14 19:43:16.075 Starting USRP --> Analog_Bridge (encoder) -> TLV thread

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:41 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

You have 2 channel drivers uncommented:

rxchannel = dahdi/pseudo                ; No radio (hub) <--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB
; rxchannel = Pi/1                      ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999            ; USBRadio (DSP)
; rxchannel = Dahdi/1                   ; PCI Quad card
; rxchannel = Beagle/1                  ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999                ; RTCM device

On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote:

Can you look at this as well…..

 

I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that.

 

Steve

 

 

; Your Repeater

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

[460310]                                        ; Change this to your assigned node number

 

                                        ; Must also be enabled in modules.conf

                                        ; Rx audio/signalling channel. Choose ONLY 1 per node stanza

 

                                        ; Enable the selected channel driver in modules.conf !!!

rxchannel = dahdi/pseudo                ; No radio (hub)

; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB

; rxchannel = Pi/1                      ; Raspberry Pi PiTA

; rxchannel = Radio/usb_1999            ; USBRadio (DSP)

; rxchannel = Dahdi/1                   ; PCI Quad card

; rxchannel = Beagle/1                  ; BeagleBoard

rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP

; rxchannel = Voter/1999                ; RTCM device

 

 

duplex = 1                              ; 0 = Half duplex with no telemetry tones or hang time.

                                        ;     Special Case: Full duplex if linktolink is set to yes.

                                        ;     This mode is preferred when interfacing with an external multiport repeater controller.

                                        ;     Comment out idrecording and idtalkover to suppress IDs also

                                        ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio.

                                        ;     This mode is preferred when interfacing a simplex node.

                                        ; 2 = Full Duplex with telemetry tones and hang time.

                                        ;     This mode is preferred when interfacing a repeater.

                                        ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio.

                                        ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.

 

linktolink = no                         ; disables forcing physical half-duplex operation of main repeater while

                                        ; still keeping half-duplex semantics (optional)

 

linkmongain = 0                         ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received.

                                        ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db.

                                        ; If linkmongain set to a positive number monitored audio will increase by the set amount in db.

                                        ; The value of linkmongain is in db. The default value is 0 db.

 

erxgain = -3                            ; Echolink receive gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

etxgain = 3                             ; Echolink transmit gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

;eannmode = 1                           ; 1 = Say only node number on echolink connects (default = 1)

                                        ; 2 = say phonetic call sign only on echolink connects

                                        ; 3 = say phonetic call sign and node number on echolink connects

 

;controlstates = controlstates          ; system control state stanza

 

scheduler = schedule                    ; scheduler stanza

functions = functions                   ; Repeater Function stanza

phone_functions = functions             ; Phone Function stanza

link_functions = functions              ; Link Function stanza

 

telemetry = telemetry                   ; Telemetry stanza

morse = morse                           ; Morse stanza

wait_times = wait-times                 ; Wait times stanza

 

context = radio                         ; dialing context for phone

callerid = "Repeater" <0000000000>      ; callerid for phone calls

accountcode = RADIO                     ; account code (optional)

 

hangtime = 5000                         ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms)

althangtime = 4000                      ; longer squelch tail

totime = 180000                         ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

 

idrecording = |iWA4XYZ                  ; cording or morse string see http://ohnosec.org/drupal/node/87

idtalkover = |iWA4XYZ                   ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129

                                        ; See Telemetry section Example: idrecording = rpt/nodenames/1999

idtime = 540000                         ; id interval time (in ms) (optional) Default 5 minutes (300000 ms)

politeid = 30000                        ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)

 

unlinkedct = ct2                        ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none)

remotect = ct3                          ; remote linked courtesy tone (indicates a remote is in the list of links)

linkunkeyct = ct8                       ; sent when a transmission received over the link unkeys

;nolocallinkct = 0                      ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).

 

;connpgm = yourconnectprogram           ; Disabled. Execute a program you specify on connect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being connected to us (them)

;discpgm = yourdisconnectprogram        ; Disabled. Execute a program you specify on disconnect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being disconnected from us (them)

 

;lnkactenable = 0                       ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.

 

;lnkacttime = 1800                      ; Link activity timer time in seconds.

;lnkactmacro = *52                      ; Function to execute when link activity timer expires.

;lnkacttimerwarn = 30seconds            ; Message to play when the link activity timer has 30 seconds left.

 

;remote_inact_timeout =                 ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60)

;remote_timeout =                       ; Session time out for remote base. Set to 0 to disable. (60 * 60)

;remote_timeout_warning_freq =          ; 30

;remote_timeout_warning =               ; (3 * 60)

 

;nounkeyct = 0                          ; Set to a 1 to eliminate courtesy tones and associated delays.

 

holdofftelem = 0                        ; Hold off all telemetry when signal is present on receiver or from connected nodes

                                        ; except when an ID needs to be done and there is a signal coming from a connected node.

 

telemdefault = 0                        ; 0 = telemetry output off

                                        ; 1 = telemetry output on (default = 1)

                                        ; 2 = timed telemetry output on command execution and for a short time thereafter.

 

telemdynamic = 1                        ; 0 = disallow users to change the local telemetry setting with a COP command,

                                        ; 1 = Allow users to change the setting with a COP command. (default = 1)

 

;beaconing = 0                          ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)

 

parrotmode = 0                          ; 0 = Parrot Off (default = 0)

                                        ; 1 = Parrot On Command

                                        ; 2 = Parrot Always

                                        ; 3 = Parrot Once by Command

 

parrottime = 1000                       ; Set the amount of time in milliseconds

                                        ; to wait before parroting what was received

 

;rxnotch=1065,40                        ; (Optional) Notch a particular frequency for a specified

                                        ; b/w. app_rpt must have been compiled with

                                        ; the notch option

 

startup_macro =

 

; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign   ; Point to alternate nodename sound directory

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Need more information on these

 

;extnodes = extnodes-different  ; section in extnodefile containing dynamic node information (optional)

;extnodefile = /foo/nodes       ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional)

;extnodefile2 =                 ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes????

;nodenames = /foo/names         ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames

;archivedir = /tmp              ; defines and enables activity recording into specified directory (optional)

;monminblocks = 2048            ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)

 

;                               ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set

;                               ; to support tail messages. They can be omitted otherwise.

;tailmessagetime = 300000       ; Play a tail message every 5 mins

;tailsquashedtime = 30000       ; If squashed by another user,

;                               ; try again after 30 seconds

;tailmessagelist = msg1,msg2    ; list of messages to be played for tail message

 

; alt_functions

; ctgroup

; dphone_functions

; idtime

; iobase

; iospeed

; locallist

; mars          Remote Base

; memory

; nobusyout

; nodes

; nolocallinkct

; notelemtx

; outxlat

; parrot

; propagate_phonedtmf

; rptnode

; rptinactmacro  Macro to execute when inactivity timer expires

; rptinacttime   Inactivity timer time in seconds  (0 seconds disables feature)

; rxnotch       Optional Audio notch

; simplexphonedelay

; tonemacro

; tonezone

; txlimits

 

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

 

; *** Status Reporting ***

 

; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org

statpost_url = http://stats.allstarlink.org/uhandler ; Status updates

 

[functions]

 

; Prefix        Functions

; *1            Disconnect Link

; *2            Monitor Link

; *3            Connect Link

; *4            Command Mode

; *5            Macros

; *6            User Functions

; *7            Connection Status/Functions

; *8            User Functions

; *9            User Functions

; *0            User Functions

 

; *A            User Functions

; *B            User Functions

; *C            User Functions

; *D            User Functions

 

 

; Mandatory Command Codes

; http://docs.allstarlink.org/drupal/node/91

 

1 = ilink,1             ; Disconnect specified link

2 = ilink,2             ; Connect specified link -- monitor only

3 = ilink,3             ; Connect specified link -- tranceive

4 = ilink,4             ; Enter command mode on specified link

70 = ilink,5            ; System status

99 = cop,6              ; PTT (phone mode only)

 

; End Mandatory Command Codes

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Macro Commands

5 = macro

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Autopatch Commands

; Note, This may be a good place for other 2 digit frequently used commands

 

61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000  ; Autopatch up

62 = autopatchdn                                                 ; Autopatch down

 

; autopatchup can optionally take comma delimited setting=value pairs:

 

; context = string              ; Override default context with "string"

; dialtime = ms                 ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second)

; farenddisconnect = 1          ; Automatically disconnect when called party hangs up

; noct = 1                      ; Don't send repeater courtesy tone during autopatch calls

; quiet = 1                     ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up

                                ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Status Commands

 

; 1 - Force ID (global)

; 2 - Give Time of Day (global)

; 3 - Give software Version (global)

; 4 - Give GPS location info

; 5 - Last (dtmf) user

; 11 - Force ID (local only)

; 12 - Give Time of Day (local only)

 

721 = status,1          ; Force ID (global)

722 = status,2          ; Give Time of Day (global)

723 = status,3          ; Give software Version (global)

724 = status,4          ; Give GPS location info

725 = status,5          ; Last (dtmf) user

711 = status,11         ; Force ID (local only)

712 = status,12         ; Give Time of Day (local only)

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Link Commands

 

; 1 - Disconnect specified link

; 2 - Connect specified link -- monitor only

; 3 - Connect specified link -- tranceive

; 4 - Enter command mode on specified link

; 5 - System status

; 6 - Disconnect all links

; 7 - Last Node to Key Up

; 8 - Connect specified link -- local monitor only

; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.

; 10 - Disconnect all RANGER links (except permalinks)

; 11 - Disconnect a previously permanently connected link

; 12 - Permanently connect specified link -- monitor only

; 13 - Permanently connect specified link -- tranceive

; 15 - Full system status (all nodes)

; 16 - Reconnect links disconnected with "disconnect all links"

; 17 - MDC test (for diag purposes)

; 18 - Permanently Connect specified link -- local monitor only

 

; ilink commands 1 through 5 are defined in the Mandatory Command section

 

806 = ilink,6                   ; Disconnect all links

807 = ilink,7                   ; Last Node to Key Up

808 = ilink,8                   ; Connect specified link -- local monitor only

809 = ilink,9,1999,"Testing"    ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes

810 = ilink,10                  ; Disconnect all RANGER links (except permalinks)

811 = ilink,11                  ; Disconnect a previously permanently connected link

812 = ilink,12                  ; Permanently connect specified link -- monitor only

813 = ilink,13                  ; Permanently connect specified link -- tranceive

815 = ilink,15                  ; Full system status (all nodes)

816 = ilink,16                  ; Reconnect links disconnected with "disconnect all links"

817 = ilink,17                  ; MDC test (for diag purposes)

818 = ilink 18                  ; Permanently Connect specified link -- local monitor only

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Control operator (cop) functions. Change these to something other than these codes listed below!

 

901 = cop,1                   ��         ; System warm boot

902 = cop,2                             ; System enable

903 = cop,3                             ; System disable

 

904 = cop,4                             ; Test tone on/off (toggle)

905 = cop,5                             ; Dump system variables on console (debug use only)

 

907 = cop,7                             ; Time out timer enable

908 = cop,8                             ; Time out timer disable

 

909 = cop,9                             ; Autopatch enable

910 = cop,10                            ; Autopatch disable

 

911 = cop,11                            ; User linking functions enable

912 = cop,12                            ; User linking functions disable

 

913 = cop,13                            ; Query system control state

914 = cop,14                            ; Set system control state

 

915 = cop,15                            ; Scheduler enable

916 = cop,16                            ; Scheduler disable

 

917 = cop,17                            ; User functions enable (time, id, etc)

918 = cop,18                            ; User functions disable

 

919 = cop,19                            ; Select alternate hang time (althangtime)

920 = cop,20                            ; Select standard hangtime (hangtime)

 

921 = cop,21                            ; Enable Parrot Mode

922 = cop,22                            ; Disable Parrot Mode

923 = cop,23                            ; Birdbath (Current Parrot Cleanup/Flush)

 

924 = cop,24                            ; Flush all telemetry

925 = cop,25                            ; Query last node un-keyed

926 = cop,26                            ; Query all nodes keyed/unkeyed

927 = cop,27                            ; Reset DAQ minimum on a pin

928 = cop,28                            ; Reset DAQ maximum on a pin

 

930 = cop,30                            ; Recall Memory Setting in Attached Xcvr

 

931 = cop,31                            ; Channel Selector for Parallel Programmed Xcvr

 

932 = cop,32                            ; Touchtone pad test: command + Digit string + # to playback all digits pressed

 

933 = cop,33                            ; Local Telemetry Output Enable

934 = cop,34                            ; Local Telemetry Output Disable

935 = cop,35                            ; Local Telemetry Output on Demand

 

936 = cop,36                            ; Foreign Link Local Output Path Enable

937 = cop,37                            ; Foreign Link Local Output Path Disable

938 = cop,38                            ; Foreign Link Local Output Path Follows Local Telemetry

939 = cop,39                            ; Foreign Link Local Output Path on Demand

 

942 = cop,42                            ; Echolink announce node # only

943 = cop,43                            ; Echolink announce node Callsign only

944 = cop,44                            ; Echolink announce node # & Callsign

 

945 = cop,45                            ; Link Activity timer enable

945 = cop,46                            ; Link Activity timer disable

947 = cop,47                            ; Reset "Link Config Changed" Flag

 

948 = cop,48                            ; Send Page Tone (Tone specs separated by parenthesis)

 

949 = cop,49                            ; Disable incoming connections (control state noice)

950 = cop,50                            ; Enable incoming connections (control state noicd)

 

951 = cop,51                            ; Enable sleep mode

952 = cop,52                            ; Disable sleep mode

953 = cop,53                            ; Wake up from sleep

954 = cop,54                            ; Go to sleep

955 = cop,55                            ; Parrot Once if parrot mode is disabled

 

956 = cop,56                            ; Rx CTCSS Enable

957 = cop,57                            ; Rx CTCSS Disable

 

958 = cop.58                            ; Tx CTCSS On Input only Enable

959 = cop,59                            ; Tx CTCSS On Input only Disable

 

960 = cop,60                            ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])

                                        ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call

                                        ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.

                                        ; DestID and subcode are only specified for  the 'C' type message.

                                        ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of

                                        ; the radio being called, and the subcodes are as follows:

                                        ; Subcode '8205' is Voice Selective Call for Spectra ('Call')

                                        ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or

                                        ; Astro-Saber('Call')

                                        ; Subcode '810D' is Call Alert (like Maxtrac 'CA')

 

961 = cop,61                            ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)

962 = cop,62                            ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)

 

963 = cop,63                            ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])

964 = cop,64                            ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])

965 = cop,65                            ; Send POCSAG page (equipped channel types only)

 

[functions-remote]

 

0 = remote,1                            ; Retrieve Memory

1 = remote,2                            ; Set freq.

2 = remote,3                            ; Set tx PL tone

3 = remote,4                            ; Set rx PL tone

40 = remote,100                         ; Rx PL off

41 = remote,101                         ; Rx PL on

42 = remote,102                         ; Tx PL off

43 = remote,103                         ; Tx PL on

44 = remote,104                         ; Low Power

45 = remote,105                         ; Medium Power

46 = remote,106                         ; High Power

711 = remote,107                        ; Bump -20

714 = remote,108                        ; Bump -100

717 = remote,109                        ; Bump -500

713 = remote,110                        ; Bump +20

716 = remote,111                        ; Bump +100

719 = remote,112                        ; Bump +500

721 = remote,113                        ; Scan - slow

724 = remote,114                        ; Scan - quick

727 = remote,115                        ; Scan - fast

723 = remote,116                        ; Scan + slow

726 = remote,117                        ; Scan + quick

729 = remote,118                        ; Scan + fast

79 = remote,119                         ; Tune

51 = remote,5                           ; Long status query

52 = remote,140                         ; Short status query

67 = remote,210                         ; Send a *

69 = remote,211                         ; Send a #

;91 = remote,99,CALLSIGN,LICENSETAG     ; Remote base login.

                                        ; Define a different dtmf sequence for each user which is

                                        ; authorized to use the remote base to control access to it.

                                        ; For examble 9139583=remote,99,WB6NIL,G would grant access to

                                        ; the remote base and announce WB6NIL as being logged in.

                                        ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to

                                        ; the remote base and announce WA6ZFT as being logged in.

                                        ; When the remote base is disconnected from the originating node, the

                                        ; user will be logged out. The LICENSETAG argument is used to enforce

                                        ; tx frequency limits. See [txlimits] below.

85 = cop,6                              ; Remote base telephone key

 

 

[telemetry]

 

; Telemetry entries can be shared across all repeaters, or defined for each repeater.

; Can be a tone sequence, morse string, or a file

;

; |t - Tone escape sequence

;

; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)

; Single frequencies are created by setting freq1 or freq2 to zero.

;

; |m - Morse escape sequence

;

; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the

; [morse] section.

;

; Follow with an alphanumeric string

;

; |i - Morse ID escape sequence

;

; Sends Morse code at the ID amplitude and ID frequency as defined in the

; [morse] section.

;

; path/to/sound/file/without/extension

;

; Send the sound if in place of a constructed tone. Do not include the file extension

; Example: ct8 = rpt/bloop

; Example: idrecording = rpt/nodenames/1999

 

ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)

ct2 = |t(660,880,150,2048)

ct3 = |t(440,0,150,4096)

ct4 = |t(550,0,150,2048)

ct5 = |t(660,0,150,2048)

ct6 = |t(880,0,150,2048)

ct7 = |t(660,440,150,2048)

ct8 = |t(700,1100,150,2048)

ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)

remotemon = |t(1209,0,50,2048)                                  ; local courtesy tone when receive only

remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000)         ; local courtesy tone when linked Trancieve mode

cmdmode = |t(900,903,200,2048)

functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)

remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)

pfxtone = |t(350,440,30000,3072)

patchup = rpt/callproceeding

patchdown = rpt/callterminated

 

; As far as what the numbers mean,

; (000,000,010,000)

;   |   |   |   |-------amplitude

;   |   |   |-------------duration

;   |   |-------------------Tone 2

;   |-------------------------Tone 1

 

; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.

; Use it for a delay.  Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter)

; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.

 

; Morse code parameters, these are common to all repeaters.

 

[morse]

speed = 20                              ; Approximate speed in WPM

frequency = 800                         ; Morse Telemetry Frequency

amplitude = 4096                        ; Morse Telemetry Amplitude

idfrequency = 1065                      ; Morse ID Frequency

idamplitude = 1024                      ; Morse ID Amplitude

 

;

; This section allows wait times for telemetry events to be adjusted

; A section for wait times can be defined for every repeater

;

 

[wait-times]

telemwait = 2000                        ; Time to wait before sending most telemetry

idwait = 500                            ; Time to wait before starting ID

unkeywait = 2000                        ; Time to wait after unkey before sending CT's and link telemetry

calltermwait = 2000                     ; Time to wait before announcing "call terminated"

 

;

; This is where you define your nodes which cam be connected to.

;

 

[nodes]

; Note, if you are using automatic update for allstar link nodes,

; no allstar link nodes should be defined here. Only place a definition

; for your local nodes, and private (off of allstar link) nodes here.

 

460310 = radio@....0.1:4569/460310,NONE       ; This must be changed to your node number

                                        ; and iax port number if not the default

; Memories for remote bases

 

[memory]

;00 = 146.580,100.0,m

;01 = 147.030,103.5,m+t

;02 = 147.240,103.5,m+t

;03 = 147.765,79.7,m-t

;04 = 146.460,100.0,m

;05 = 146.550,100.0,m

 

; Place command macros here

 

[macro]

;1 = *32011#

;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#

;3 = *32001*32011*32050*32030*32060#

 

 

; Data Acquisition configuration

 

;[daq-list]

;device = device_name1

;device = device_name2

 

;Where: device_name1 and device_name2 are stanzas you define in this file

 

;device = daq-cham-1

 

; Device name

 

;[daq-cham-1]                           ; Defined in [daq-list]

;hwtype = uchameleon                    ; DAQ hardware type

;devnode = /dev/ttyUSB0                 ; DAQ device node (if required)

;1 = inadc                              ; Pin definition for an ADC channel

;2 = inadc

;3 = inadc

;4 = inadc

;5 = inadc

;6 = inadc

;7 = inadc

;8 = inadc

;9 = inp                                ; Pin definition for an input with a weak pullup resistor

;10 = inp

;11 = inp

;12 = inp

;13 = in                                ; Pin definition for an input without a weak pullup resistor

;14 = out                               ; Pin definition for an output

;15 = out

;16 = out

;17 = out

;18 = out

 

;[meter-faces]

 

;face = scale(scalepre,scalediv,scalepost),word/?,...

;

; scalepre = offset to add before dividing with scalediv

; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts).

; scalepost = offset to add after dividing with scalediv

;

;face = range(X-Y:word,X2-Y2:word,...),word/?,...

;face = bit(low-word,high-word),word/?,...

;

; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories,

; or a question mark which is  a placeholder for the measured value.

;

;

; Battery voltage 0-20 volts

;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts

; 4 quadrant wind direction

;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?

; LM34 temperature sensor with 130 deg. F full scale

;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit

; Status poll (non alarmed)

;light = bit(ha/off,ha/on),ha/light,?

 

;[alarms]

;

;tag = device,pin,node,ignorefirst,func-low,func-hi

;

;tag = a unique name for the alarm

;device = daq device to poll

;pin = the device pin to be monitored

;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it

;node = the node number to execute the function on

;func-low = the DTMF function to execute on a high to low transition

;func-high = the DTMF function to execute on a low to high transition

;

; a  '-' as a function name is shorthand for no-operation

;

;door = daq-cham-1,9,1,2017,*7,-

;pwrfail = daq-cham-1,10,0,2017,*911111,-

;

; Control states

; Allow several control operator functions to be changed at once using one command (good for scheduling)

;

;[controlstates]

;statenum = copcmd,[copcmd]...

;0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation

;1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation

;2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation

 

; Scheduler - execute a macro at a given time

 

[schedule]

;dtmf_function =  m h dom mon dow  ; ala cron, star is implied

;2 = 00 00 * * *   ; at midnight, execute macro 2.

 

#includeifexists custom/rpt.conf

 

 

 

 

Analog_Bridge.ini

 

 

; Analog_Bridge configuration file.

;   This file should be placed in either /etc or it can be

;   supplied as a path on the Analog_Bridge command line.

 

; The best way to think of this file is that there are two main sections, the USRP (analog audio) and

; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and

; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.

; As you might expect, the reverse direction is defined too.

 

; Analog_Bridge supports include files. More on this later...

include = dvsm.macro

; include = asl.macro

 

; General Section describes settings for Analog_Bridge itself.

[GENERAL]

logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal

 

; Metadata management

exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)

transferRootDir = /tmp                  ; Export database files to USRP partner

subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data

 

; General vocoder setup information

decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found

useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)

emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server

 

pcmPort = 2222                          ; UDP port to send to the WebProxy

 

; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)

[AMBE_AUDIO]

address = 127.0.0.1                     ; IP address of xx_Bridge

txPort = 31103                          ; Transmit TLV frames to partner on this port

rxPort = 31100                          ; Listen for TLV frames from partner on this port

ambeMode = DMR                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)

minTxTimeMS = 2500                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)

 

; The metadata below is used when ASL is the source since it does not have any concept of digital modes

gatewayDmrId = 1112721                  ; ID to use when transmitting from Analog_Bridge 7 digit ID

repeaterID = 111272123                  ; ID of source repeater 7 digit ID plus 2 digit SSID

txTg = 31676                               ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge

txTs = 2                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge

colorCode = 1                           ; Color Code to assign DMR frames

 

; Information for USRP channel driver.  This interface uses PCM to transfer audio information

; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected

; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself,

; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.

;   When using ASL, this matches the rpt.conf ASL file with a setting like:

;   rxchannel = usrp/127.0.0.1:34001:32001

;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch

;   each instance with its own ini file.

[USRP]

address = 127.0.0.1                     ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge)

txPort = 32001                          ; Transmit USRP frames on this port

rxPort = 34001                          ; Listen for USRP frames on this port

usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)

usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)

tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)

tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

 

[MACROS]

 

; Where the macros are

; xxxx=yyyy

; xxxx is the dial string to match

; yyyy is the command line to execute

 

; xxxx must be preceded by a *

; xxxx can be any string (alphanumeric)

; yyyy is the command to execute

; yyyy will replace xxxx in the dial string

; arguments follow the macro name with a # delimiter

 

; For example using macro "5678" above would look like:

; *5678#9876

 

; Which would invoke:

; echo 9876

 

; Information for DV3000 hardware decoder

;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)

;   Use top server and port if using AMBEServer

;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)

;   Did you run AMBETest4.py before using this?

[DV3000]

address = 127.0.0.1                   ; IP address of AMBEServer

rxPort = 2460                         ; Port of AMBEServer

; address = /dev/ttyUSB0              ; Device of DV3000U on this machine

; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)

; serial = true                       ; Use serial=true f

 

 

 

 

 

 

 



Steve Siesel [K4KSA]
 

It is now working…Long hangtime I think I will change Hangtime to 20

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:51 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

Is chan_usrp enabled in modules.conf?

On 2/14/21 2:50 PM, Steve Siesel [K4KSA] wrote:

Yes…..

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:50 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

Did you fix rpt.conf and did you then restart asterisk?

On 2/14/21 2:46 PM, Steve Siesel [K4KSA] wrote:

After restarting AB and Asterisk….also md3890-emu is running

Still no Joy…Here is the latest start of Analog_bridge.log

 

 

I: 2021-02-14 19:43:13.761 Analog_Bridge is starting

M: 2021-02-14 19:43:13.762 Setting [MACROS] DMR -> /opt/MMDVM_Bridge/dvswitch.sh mode DMR

M: 2021-02-14 19:43:13.762 Setting [MACROS] DSTAR -> /opt/MMDVM_Bridge/dvswitch.sh mode DSTAR

M: 2021-02-14 19:43:13.762 Setting [MACROS] NXDN -> /opt/MMDVM_Bridge/dvswitch.sh mode NXDN

M: 2021-02-14 19:43:13.762 Setting [MACROS] P25 -> /opt/MMDVM_Bridge/dvswitch.sh mode P25

M: 2021-02-14 19:43:13.762 Setting [MACROS] YSF -> /opt/MMDVM_Bridge/dvswitch.sh mode YSF

M: 2021-02-14 19:43:13.762 Setting [MACROS] dbupdate -> /opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles

M: 2021-02-14 19:43:13.764 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh

M: 2021-02-14 19:43:13.765 Setting [] include -> dvsm.macro

M: 2021-02-14 19:43:13.766 Setting [GENERAL] logLevel -> 2

M: 2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata -> true

M: 2021-02-14 19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp

M: 2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv

M: 2021-02-14 19:43:13.768 Setting [GENERAL] decoderFallBack -> true

M: 2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator -> false

M: 2021-02-14 19:43:13.769 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470

M: 2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort -> 2222

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1

M: 2021-02-14 19:43:13.773 Setting [USRP] address -> 127.0.0.1

M: 2021-02-14 19:43:13.773 Setting [USRP] txPort -> 32001

M: 2021-02-14 19:43:13.773 Setting [USRP] rxPort -> 34001

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpGain -> 1.10

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvGain -> 0.35

M: 2021-02-14 19:43:13.776 Setting [DV3000] address -> 127.0.0.1

M: 2021-02-14 19:43:13.776 Setting [DV3000] rxPort -> 2460

I: 2021-02-14 19:43:13.777 Open UDP listener on 127.0.0.1:31100

I: 2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001

M: 2021-02-14 19:43:13.777 Connecting to DV3000 hardware......

W: 2021-02-14 19:43:13.871 DV3000 did not reset at 127.0.0.1:2460

W: 2021-02-14 19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset failed)

I: 2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850

I: 2021-02-14 19:43:16.073 Default extended metadata <K4KSA>

W: 2021-02-14 19:43:16.073 Using software MBE decoder version 1.2.3

W: 2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE vocoder

I: 2021-02-14 19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s) 32001

I: 2021-02-14 19:43:16.074 Sending PCM to  clients at 127.0.0.1 on port 2222

I: 2021-02-14 19:43:16.074 Starting TLV --> Analog_Bridge (decoder) --> USRP thread

I: 2021-02-14 19:43:16.075 Starting USRP --> Analog_Bridge (encoder) -> TLV thread

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:41 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

You have 2 channel drivers uncommented:

rxchannel = dahdi/pseudo                ; No radio (hub) <--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB
; rxchannel = Pi/1                      ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999            ; USBRadio (DSP)
; rxchannel = Dahdi/1                   ; PCI Quad card
; rxchannel = Beagle/1                  ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999                ; RTCM device

On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote:

Can you look at this as well…..

 

I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that.

 

Steve

 

 

; Your Repeater

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

[460310]                                        ; Change this to your assigned node number

 

                                        ; Must also be enabled in modules.conf

                                        ; Rx audio/signalling channel. Choose ONLY 1 per node stanza

 

                                        ; Enable the selected channel driver in modules.conf !!!

rxchannel = dahdi/pseudo                ; No radio (hub)

; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB

; rxchannel = Pi/1                      ; Raspberry Pi PiTA

; rxchannel = Radio/usb_1999            ; USBRadio (DSP)

; rxchannel = Dahdi/1                   ; PCI Quad card

; rxchannel = Beagle/1                  ; BeagleBoard

rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP

; rxchannel = Voter/1999                ; RTCM device

 

 

duplex = 1                              ; 0 = Half duplex with no telemetry tones or hang time.

                                        ;     Special Case: Full duplex if linktolink is set to yes.

                                        ;     This mode is preferred when interfacing with an external multiport repeater controller.

                                        ;     Comment out idrecording and idtalkover to suppress IDs also

                                        ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio.

                                        ;     This mode is preferred when interfacing a simplex node.

                                        ; 2 = Full Duplex with telemetry tones and hang time.

                                        ;     This mode is preferred when interfacing a repeater.

                                        ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio.

                                        ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.

 

linktolink = no                         ; disables forcing physical half-duplex operation of main repeater while

                                        ; still keeping half-duplex semantics (optional)

 

linkmongain = 0                         ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received.

                                        ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db.

                                        ; If linkmongain set to a positive number monitored audio will increase by the set amount in db.

                                        ; The value of linkmongain is in db. The default value is 0 db.

 

erxgain = -3                            ; Echolink receive gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

etxgain = 3                             ; Echolink transmit gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

;eannmode = 1                           ; 1 = Say only node number on echolink connects (default = 1)

                                        ; 2 = say phonetic call sign only on echolink connects

                                        ; 3 = say phonetic call sign and node number on echolink connects

 

;controlstates = controlstates          ; system control state stanza

 

scheduler = schedule                    ; scheduler stanza

functions = functions                   ; Repeater Function stanza

phone_functions = functions             ; Phone Function stanza

link_functions = functions              ; Link Function stanza

 

telemetry = telemetry                   ; Telemetry stanza

morse = morse                           ; Morse stanza

wait_times = wait-times                 ; Wait times stanza

 

context = radio                         ; dialing context for phone

callerid = "Repeater" <0000000000>      ; callerid for phone calls

accountcode = RADIO                     ; account code (optional)

 

hangtime = 5000                         ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms)

althangtime = 4000                      ; longer squelch tail

totime = 180000                         ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

 

idrecording = |iWA4XYZ                  ; cording or morse string see http://ohnosec.org/drupal/node/87

idtalkover = |iWA4XYZ                   ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129

                                        ; See Telemetry section Example: idrecording = rpt/nodenames/1999

idtime = 540000                         ; id interval time (in ms) (optional) Default 5 minutes (300000 ms)

politeid = 30000                        ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)

 

unlinkedct = ct2                        ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none)

remotect = ct3                          ; remote linked courtesy tone (indicates a remote is in the list of links)

linkunkeyct = ct8                       ; sent when a transmission received over the link unkeys

;nolocallinkct = 0                      ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).

 

;connpgm = yourconnectprogram           ; Disabled. Execute a program you specify on connect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being connected to us (them)

;discpgm = yourdisconnectprogram        ; Disabled. Execute a program you specify on disconnect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being disconnected from us (them)

 

;lnkactenable = 0                       ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.

 

;lnkacttime = 1800                      ; Link activity timer time in seconds.

;lnkactmacro = *52                      ; Function to execute when link activity timer expires.

;lnkacttimerwarn = 30seconds            ; Message to play when the link activity timer has 30 seconds left.

 

;remote_inact_timeout =                 ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60)

;remote_timeout =                       ; Session time out for remote base. Set to 0 to disable. (60 * 60)

;remote_timeout_warning_freq =          ; 30

;remote_timeout_warning =               ; (3 * 60)

 

;nounkeyct = 0                          ; Set to a 1 to eliminate courtesy tones and associated delays.

 

holdofftelem = 0                        ; Hold off all telemetry when signal is present on receiver or from connected nodes

                                        ; except when an ID needs to be done and there is a signal coming from a connected node.

 

telemdefault = 0                        ; 0 = telemetry output off

                                        ; 1 = telemetry output on (default = 1)

                                        ; 2 = timed telemetry output on command execution and for a short time thereafter.

 

telemdynamic = 1                        ; 0 = disallow users to change the local telemetry setting with a COP command,

                                        ; 1 = Allow users to change the setting with a COP command. (default = 1)

 

;beaconing = 0                          ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)

 

parrotmode = 0                          ; 0 = Parrot Off (default = 0)

                                        ; 1 = Parrot On Command

                                        ; 2 = Parrot Always

                                        ; 3 = Parrot Once by Command

 

parrottime = 1000                       ; Set the amount of time in milliseconds

                                        ; to wait before parroting what was received

 

;rxnotch=1065,40                        ; (Optional) Notch a particular frequency for a specified

                                        ; b/w. app_rpt must have been compiled with

                                        ; the notch option

 

startup_macro =

 

; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign   ; Point to alternate nodename sound directory

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Need more information on these

 

;extnodes = extnodes-different  ; section in extnodefile containing dynamic node information (optional)

;extnodefile = /foo/nodes       ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional)

;extnodefile2 =                 ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes????

;nodenames = /foo/names         ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames

;archivedir = /tmp              ; defines and enables activity recording into specified directory (optional)

;monminblocks = 2048            ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)

 

;                               ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set

;                               ; to support tail messages. They can be omitted otherwise.

;tailmessagetime = 300000       ; Play a tail message every 5 mins

;tailsquashedtime = 30000       ; If squashed by another user,

;                               ; try again after 30 seconds

;tailmessagelist = msg1,msg2    ; list of messages to be played for tail message

 

; alt_functions

; ctgroup

; dphone_functions

; idtime

; iobase

; iospeed

; locallist

; mars          Remote Base

; memory

; nobusyout

; nodes

; nolocallinkct

; notelemtx

; outxlat

; parrot

; propagate_phonedtmf

; rptnode

; rptinactmacro  Macro to execute when inactivity timer expires

; rptinacttime   Inactivity timer time in seconds  (0 seconds disables feature)

; rxnotch       Optional Audio notch

; simplexphonedelay

; tonemacro

; tonezone

; txlimits

 

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

 

; *** Status Reporting ***

 

; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org

statpost_url = http://stats.allstarlink.org/uhandler ; Status updates

 

[functions]

 

; Prefix        Functions

; *1            Disconnect Link

; *2            Monitor Link

; *3            Connect Link

; *4            Command Mode

; *5            Macros

; *6            User Functions

; *7            Connection Status/Functions

; *8            User Functions

; *9            User Functions

; *0            User Functions

 

; *A            User Functions

; *B            User Functions

; *C            User Functions

; *D            User Functions

 

 

; Mandatory Command Codes

; http://docs.allstarlink.org/drupal/node/91

 

1 = ilink,1             ; Disconnect specified link

2 = ilink,2             ; Connect specified link -- monitor only

3 = ilink,3             ; Connect specified link -- tranceive

4 = ilink,4             ; Enter command mode on specified link

70 = ilink,5            ; System status

99 = cop,6              ; PTT (phone mode only)

 

; End Mandatory Command Codes

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Macro Commands

5 = macro

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Autopatch Commands

; Note, This may be a good place for other 2 digit frequently used commands

 

61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000  ; Autopatch up

62 = autopatchdn                                                 ; Autopatch down

 

; autopatchup can optionally take comma delimited setting=value pairs:

 

; context = string              ; Override default context with "string"

; dialtime = ms                 ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second)

; farenddisconnect = 1          ; Automatically disconnect when called party hangs up

; noct = 1                      ; Don't send repeater courtesy tone during autopatch calls

; quiet = 1                     ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up

                                ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Status Commands

 

; 1 - Force ID (global)

; 2 - Give Time of Day (global)

; 3 - Give software Version (global)

; 4 - Give GPS location info

; 5 - Last (dtmf) user

; 11 - Force ID (local only)

; 12 - Give Time of Day (local only)

 

721 = status,1          ; Force ID (global)

722 = status,2          ; Give Time of Day (global)

723 = status,3          ; Give software Version (global)

724 = status,4          ; Give GPS location info

725 = status,5          ; Last (dtmf) user

711 = status,11         ; Force ID (local only)

712 = status,12         ; Give Time of Day (local only)

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Link Commands

 

; 1 - Disconnect specified link

; 2 - Connect specified link -- monitor only

; 3 - Connect specified link -- tranceive

; 4 - Enter command mode on specified link

; 5 - System status

; 6 - Disconnect all links

; 7 - Last Node to Key Up

; 8 - Connect specified link -- local monitor only

; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.

; 10 - Disconnect all RANGER links (except permalinks)

; 11 - Disconnect a previously permanently connected link

; 12 - Permanently connect specified link -- monitor only

; 13 - Permanently connect specified link -- tranceive

; 15 - Full system status (all nodes)

; 16 - Reconnect links disconnected with "disconnect all links"

; 17 - MDC test (for diag purposes)

; 18 - Permanently Connect specified link -- local monitor only

 

; ilink commands 1 through 5 are defined in the Mandatory Command section

 

806 = ilink,6                   ; Disconnect all links

807 = ilink,7                   ; Last Node to Key Up

808 = ilink,8                   ; Connect specified link -- local monitor only

809 = ilink,9,1999,"Testing"    ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes

810 = ilink,10                  ; Disconnect all RANGER links (except permalinks)

811 = ilink,11                  ; Disconnect a previously permanently connected link

812 = ilink,12                  ; Permanently connect specified link -- monitor only

813 = ilink,13                  ; Permanently connect specified link -- tranceive

815 = ilink,15                  ; Full system status (all nodes)

816 = ilink,16                  ; Reconnect links disconnected with "disconnect all links"

817 = ilink,17                  ; MDC test (for diag purposes)

818 = ilink 18                  ; Permanently Connect specified link -- local monitor only

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Control operator (cop) functions. Change these to something other than these codes listed below!

 

901 = cop,1                   ��         ; System warm boot

902 = cop,2                             ; System enable

903 = cop,3                             ; System disable

 

904 = cop,4                             ; Test tone on/off (toggle)

905 = cop,5                             ; Dump system variables on console (debug use only)

 

907 = cop,7                             ; Time out timer enable

908 = cop,8                             ; Time out timer disable

 

909 = cop,9                             ; Autopatch enable

910 = cop,10                            ; Autopatch disable

 

911 = cop,11                            ; User linking functions enable

912 = cop,12                            ; User linking functions disable

 

913 = cop,13                            ; Query system control state

914 = cop,14                            ; Set system control state

 

915 = cop,15                            ; Scheduler enable

916 = cop,16                            ; Scheduler disable

 

917 = cop,17                            ; User functions enable (time, id, etc)

918 = cop,18                            ; User functions disable

 

919 = cop,19                            ; Select alternate hang time (althangtime)

920 = cop,20                            ; Select standard hangtime (hangtime)

 

921 = cop,21                            ; Enable Parrot Mode

922 = cop,22                            ; Disable Parrot Mode

923 = cop,23                            ; Birdbath (Current Parrot Cleanup/Flush)

 

924 = cop,24                            ; Flush all telemetry

925 = cop,25                            ; Query last node un-keyed

926 = cop,26                            ; Query all nodes keyed/unkeyed

927 = cop,27                            ; Reset DAQ minimum on a pin

928 = cop,28                            ; Reset DAQ maximum on a pin

 

930 = cop,30                            ; Recall Memory Setting in Attached Xcvr

 

931 = cop,31                            ; Channel Selector for Parallel Programmed Xcvr

 

932 = cop,32                            ; Touchtone pad test: command + Digit string + # to playback all digits pressed

 

933 = cop,33                            ; Local Telemetry Output Enable

934 = cop,34                            ; Local Telemetry Output Disable

935 = cop,35                            ; Local Telemetry Output on Demand

 

936 = cop,36                            ; Foreign Link Local Output Path Enable

937 = cop,37                            ; Foreign Link Local Output Path Disable

938 = cop,38                            ; Foreign Link Local Output Path Follows Local Telemetry

939 = cop,39                            ; Foreign Link Local Output Path on Demand

 

942 = cop,42                            ; Echolink announce node # only

943 = cop,43                            ; Echolink announce node Callsign only

944 = cop,44                            ; Echolink announce node # & Callsign

 

945 = cop,45                            ; Link Activity timer enable

945 = cop,46                            ; Link Activity timer disable

947 = cop,47                            ; Reset "Link Config Changed" Flag

 

948 = cop,48                            ; Send Page Tone (Tone specs separated by parenthesis)

 

949 = cop,49                            ; Disable incoming connections (control state noice)

950 = cop,50                            ; Enable incoming connections (control state noicd)

 

951 = cop,51                            ; Enable sleep mode

952 = cop,52                            ; Disable sleep mode

953 = cop,53                            ; Wake up from sleep

954 = cop,54                            ; Go to sleep

955 = cop,55                            ; Parrot Once if parrot mode is disabled

 

956 = cop,56                            ; Rx CTCSS Enable

957 = cop,57                            ; Rx CTCSS Disable

 

958 = cop.58                            ; Tx CTCSS On Input only Enable

959 = cop,59                            ; Tx CTCSS On Input only Disable

 

960 = cop,60                            ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])

                                        ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call

                                        ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.

                                        ; DestID and subcode are only specified for  the 'C' type message.

                                        ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of

                                        ; the radio being called, and the subcodes are as follows:

                                        ; Subcode '8205' is Voice Selective Call for Spectra ('Call')

                                        ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or

                                        ; Astro-Saber('Call')

                                        ; Subcode '810D' is Call Alert (like Maxtrac 'CA')

 

961 = cop,61                            ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)

962 = cop,62                            ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)

 

963 = cop,63                            ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])

964 = cop,64                            ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])

965 = cop,65                            ; Send POCSAG page (equipped channel types only)

 

[functions-remote]

 

0 = remote,1                            ; Retrieve Memory

1 = remote,2                            ; Set freq.

2 = remote,3                            ; Set tx PL tone

3 = remote,4                            ; Set rx PL tone

40 = remote,100                         ; Rx PL off

41 = remote,101                         ; Rx PL on

42 = remote,102                         ; Tx PL off

43 = remote,103                         ; Tx PL on

44 = remote,104                         ; Low Power

45 = remote,105                         ; Medium Power

46 = remote,106                         ; High Power

711 = remote,107                        ; Bump -20

714 = remote,108                        ; Bump -100

717 = remote,109                        ; Bump -500

713 = remote,110                        ; Bump +20

716 = remote,111                        ; Bump +100

719 = remote,112                        ; Bump +500

721 = remote,113                        ; Scan - slow

724 = remote,114                        ; Scan - quick

727 = remote,115                        ; Scan - fast

723 = remote,116                        ; Scan + slow

726 = remote,117                        ; Scan + quick

729 = remote,118                        ; Scan + fast

79 = remote,119                         ; Tune

51 = remote,5                           ; Long status query

52 = remote,140                         ; Short status query

67 = remote,210                         ; Send a *

69 = remote,211                         ; Send a #

;91 = remote,99,CALLSIGN,LICENSETAG     ; Remote base login.

                                        ; Define a different dtmf sequence for each user which is

                                        ; authorized to use the remote base to control access to it.

                                        ; For examble 9139583=remote,99,WB6NIL,G would grant access to

                                        ; the remote base and announce WB6NIL as being logged in.

                                        ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to

                                        ; the remote base and announce WA6ZFT as being logged in.

                                        ; When the remote base is disconnected from the originating node, the

                                        ; user will be logged out. The LICENSETAG argument is used to enforce

                                        ; tx frequency limits. See [txlimits] below.

85 = cop,6                              ; Remote base telephone key

 

 

[telemetry]

 

; Telemetry entries can be shared across all repeaters, or defined for each repeater.

; Can be a tone sequence, morse string, or a file

;

; |t - Tone escape sequence

;

; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)

; Single frequencies are created by setting freq1 or freq2 to zero.

;

; |m - Morse escape sequence

;

; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the

; [morse] section.

;

; Follow with an alphanumeric string

;

; |i - Morse ID escape sequence

;

; Sends Morse code at the ID amplitude and ID frequency as defined in the

; [morse] section.

;

; path/to/sound/file/without/extension

;

; Send the sound if in place of a constructed tone. Do not include the file extension

; Example: ct8 = rpt/bloop

; Example: idrecording = rpt/nodenames/1999

 

ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)

ct2 = |t(660,880,150,2048)

ct3 = |t(440,0,150,4096)

ct4 = |t(550,0,150,2048)

ct5 = |t(660,0,150,2048)

ct6 = |t(880,0,150,2048)

ct7 = |t(660,440,150,2048)

ct8 = |t(700,1100,150,2048)

ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)

remotemon = |t(1209,0,50,2048)                                  ; local courtesy tone when receive only

remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000)         ; local courtesy tone when linked Trancieve mode

cmdmode = |t(900,903,200,2048)

functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)

remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)

pfxtone = |t(350,440,30000,3072)

patchup = rpt/callproceeding

patchdown = rpt/callterminated

 

; As far as what the numbers mean,

; (000,000,010,000)

;   |   |   |   |-------amplitude

;   |   |   |-------------duration

;   |   |-------------------Tone 2

;   |-------------------------Tone 1

 

; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.

; Use it for a delay.  Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter)

; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.

 

; Morse code parameters, these are common to all repeaters.

 

[morse]

speed = 20                              ; Approximate speed in WPM

frequency = 800                         ; Morse Telemetry Frequency

amplitude = 4096                        ; Morse Telemetry Amplitude

idfrequency = 1065                      ; Morse ID Frequency

idamplitude = 1024                      ; Morse ID Amplitude

 

;

; This section allows wait times for telemetry events to be adjusted

; A section for wait times can be defined for every repeater

;

 

[wait-times]

telemwait = 2000                        ; Time to wait before sending most telemetry

idwait = 500                            ; Time to wait before starting ID

unkeywait = 2000                        ; Time to wait after unkey before sending CT's and link telemetry

calltermwait = 2000                     ; Time to wait before announcing "call terminated"

 

;

; This is where you define your nodes which cam be connected to.

;

 

[nodes]

; Note, if you are using automatic update for allstar link nodes,

; no allstar link nodes should be defined here. Only place a definition

; for your local nodes, and private (off of allstar link) nodes here.

 

460310 = radio@....0.1:4569/460310,NONE       ; This must be changed to your node number

                                        ; and iax port number if not the default

; Memories for remote bases

 

[memory]

;00 = 146.580,100.0,m

;01 = 147.030,103.5,m+t

;02 = 147.240,103.5,m+t

;03 = 147.765,79.7,m-t

;04 = 146.460,100.0,m

;05 = 146.550,100.0,m

 

; Place command macros here

 

[macro]

;1 = *32011#

;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#

;3 = *32001*32011*32050*32030*32060#

 

 

; Data Acquisition configuration

 

;[daq-list]

;device = device_name1

;device = device_name2

 

;Where: device_name1 and device_name2 are stanzas you define in this file

 

;device = daq-cham-1

 

; Device name

 

;[daq-cham-1]                           ; Defined in [daq-list]

;hwtype = uchameleon                    ; DAQ hardware type

;devnode = /dev/ttyUSB0                 ; DAQ device node (if required)

;1 = inadc                              ; Pin definition for an ADC channel

;2 = inadc

;3 = inadc

;4 = inadc

;5 = inadc

;6 = inadc

;7 = inadc

;8 = inadc

;9 = inp                                ; Pin definition for an input with a weak pullup resistor

;10 = inp

;11 = inp

;12 = inp

;13 = in                                ; Pin definition for an input without a weak pullup resistor

;14 = out                               ; Pin definition for an output

;15 = out

;16 = out

;17 = out

;18 = out

 

;[meter-faces]

 

;face = scale(scalepre,scalediv,scalepost),word/?,...

;

; scalepre = offset to add before dividing with scalediv

; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts).

; scalepost = offset to add after dividing with scalediv

;

;face = range(X-Y:word,X2-Y2:word,...),word/?,...

;face = bit(low-word,high-word),word/?,...

;

; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories,

; or a question mark which is  a placeholder for the measured value.

;

;

; Battery voltage 0-20 volts

;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts

; 4 quadrant wind direction

;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?

; LM34 temperature sensor with 130 deg. F full scale

;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit

; Status poll (non alarmed)

;light = bit(ha/off,ha/on),ha/light,?

 

;[alarms]

;

;tag = device,pin,node,ignorefirst,func-low,func-hi

;

;tag = a unique name for the alarm

;device = daq device to poll

;pin = the device pin to be monitored

;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it

;node = the node number to execute the function on

;func-low = the DTMF function to execute on a high to low transition

;func-high = the DTMF function to execute on a low to high transition

;

; a  '-' as a function name is shorthand for no-operation

;

;door = daq-cham-1,9,1,2017,*7,-

;pwrfail = daq-cham-1,10,0,2017,*911111,-

;

; Control states

; Allow several control operator functions to be changed at once using one command (good for scheduling)

;

;[controlstates]

;statenum = copcmd,[copcmd]...

;0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation

;1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation

;2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation

 

; Scheduler - execute a macro at a given time

 

[schedule]

;dtmf_function =  m h dom mon dow  ; ala cron, star is implied

;2 = 00 00 * * *   ; at midnight, execute macro 2.

 

#includeifexists custom/rpt.conf

 

 

 

 

Analog_Bridge.ini

 

 

; Analog_Bridge configuration file.

;   This file should be placed in either /etc or it can be

;   supplied as a path on the Analog_Bridge command line.

 

; The best way to think of this file is that there are two main sections, the USRP (analog audio) and

; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and

; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.

; As you might expect, the reverse direction is defined too.

 

; Analog_Bridge supports include files. More on this later...

include = dvsm.macro

; include = asl.macro

 

; General Section describes settings for Analog_Bridge itself.

[GENERAL]

logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal

 

; Metadata management

exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)

transferRootDir = /tmp                  ; Export database files to USRP partner

subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data

 

; General vocoder setup information

decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found

useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)

emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server

 

pcmPort = 2222                          ; UDP port to send to the WebProxy

 

; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)

[AMBE_AUDIO]

address = 127.0.0.1                     ; IP address of xx_Bridge

txPort = 31103                          ; Transmit TLV frames to partner on this port

rxPort = 31100                          ; Listen for TLV frames from partner on this port

ambeMode = DMR                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)

minTxTimeMS = 2500                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)

 

; The metadata below is used when ASL is the source since it does not have any concept of digital modes

gatewayDmrId = 1112721                  ; ID to use when transmitting from Analog_Bridge 7 digit ID

repeaterID = 111272123                  ; ID of source repeater 7 digit ID plus 2 digit SSID

txTg = 31676                               ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge

txTs = 2                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge

colorCode = 1                           ; Color Code to assign DMR frames

 

; Information for USRP channel driver.  This interface uses PCM to transfer audio information

; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected

; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself,

; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.

;   When using ASL, this matches the rpt.conf ASL file with a setting like:

;   rxchannel = usrp/127.0.0.1:34001:32001

;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch

;   each instance with its own ini file.

[USRP]

address = 127.0.0.1                     ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge)

txPort = 32001                          ; Transmit USRP frames on this port

rxPort = 34001                          ; Listen for USRP frames on this port

usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)

usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)

tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)

tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

 

[MACROS]

 

; Where the macros are

; xxxx=yyyy

; xxxx is the dial string to match

; yyyy is the command line to execute

 

; xxxx must be preceded by a *

; xxxx can be any string (alphanumeric)

; yyyy is the command to execute

; yyyy will replace xxxx in the dial string

; arguments follow the macro name with a # delimiter

 

; For example using macro "5678" above would look like:

; *5678#9876

 

; Which would invoke:

; echo 9876

 

; Information for DV3000 hardware decoder

;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)

;   Use top server and port if using AMBEServer

;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)

;   Did you run AMBETest4.py before using this?

[DV3000]

address = 127.0.0.1                   ; IP address of AMBEServer

rxPort = 2460                         ; Port of AMBEServer

; address = /dev/ttyUSB0              ; Device of DV3000U on this machine

; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)

; serial = true                       ; Use serial=true f

 

 

 

 

 

 

 


Steve N4IRS
 

Is chan_usrp enabled in modules.conf?

On 2/14/21 2:50 PM, Steve Siesel [K4KSA] wrote:

Yes…..

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:50 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

Did you fix rpt.conf and did you then restart asterisk?

On 2/14/21 2:46 PM, Steve Siesel [K4KSA] wrote:

After restarting AB and Asterisk….also md3890-emu is running

Still no Joy…Here is the latest start of Analog_bridge.log

 

 

I: 2021-02-14 19:43:13.761 Analog_Bridge is starting

M: 2021-02-14 19:43:13.762 Setting [MACROS] DMR -> /opt/MMDVM_Bridge/dvswitch.sh mode DMR

M: 2021-02-14 19:43:13.762 Setting [MACROS] DSTAR -> /opt/MMDVM_Bridge/dvswitch.sh mode DSTAR

M: 2021-02-14 19:43:13.762 Setting [MACROS] NXDN -> /opt/MMDVM_Bridge/dvswitch.sh mode NXDN

M: 2021-02-14 19:43:13.762 Setting [MACROS] P25 -> /opt/MMDVM_Bridge/dvswitch.sh mode P25

M: 2021-02-14 19:43:13.762 Setting [MACROS] YSF -> /opt/MMDVM_Bridge/dvswitch.sh mode YSF

M: 2021-02-14 19:43:13.762 Setting [MACROS] dbupdate -> /opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles

M: 2021-02-14 19:43:13.764 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh

M: 2021-02-14 19:43:13.765 Setting [] include -> dvsm.macro

M: 2021-02-14 19:43:13.766 Setting [GENERAL] logLevel -> 2

M: 2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata -> true

M: 2021-02-14 19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp

M: 2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv

M: 2021-02-14 19:43:13.768 Setting [GENERAL] decoderFallBack -> true

M: 2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator -> false

M: 2021-02-14 19:43:13.769 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470

M: 2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort -> 2222

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1

M: 2021-02-14 19:43:13.773 Setting [USRP] address -> 127.0.0.1

M: 2021-02-14 19:43:13.773 Setting [USRP] txPort -> 32001

M: 2021-02-14 19:43:13.773 Setting [USRP] rxPort -> 34001

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpGain -> 1.10

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvGain -> 0.35

M: 2021-02-14 19:43:13.776 Setting [DV3000] address -> 127.0.0.1

M: 2021-02-14 19:43:13.776 Setting [DV3000] rxPort -> 2460

I: 2021-02-14 19:43:13.777 Open UDP listener on 127.0.0.1:31100

I: 2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001

M: 2021-02-14 19:43:13.777 Connecting to DV3000 hardware......

W: 2021-02-14 19:43:13.871 DV3000 did not reset at 127.0.0.1:2460

W: 2021-02-14 19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset failed)

I: 2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850

I: 2021-02-14 19:43:16.073 Default extended metadata <K4KSA>

W: 2021-02-14 19:43:16.073 Using software MBE decoder version 1.2.3

W: 2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE vocoder

I: 2021-02-14 19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s) 32001

I: 2021-02-14 19:43:16.074 Sending PCM to  clients at 127.0.0.1 on port 2222

I: 2021-02-14 19:43:16.074 Starting TLV --> Analog_Bridge (decoder) --> USRP thread

I: 2021-02-14 19:43:16.075 Starting USRP --> Analog_Bridge (encoder) -> TLV thread

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:41 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

You have 2 channel drivers uncommented:

rxchannel = dahdi/pseudo                ; No radio (hub) <--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB
; rxchannel = Pi/1                      ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999            ; USBRadio (DSP)
; rxchannel = Dahdi/1                   ; PCI Quad card
; rxchannel = Beagle/1                  ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999                ; RTCM device

On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote:

Can you look at this as well…..

 

I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that.

 

Steve

 

 

; Your Repeater

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

[460310]                                        ; Change this to your assigned node number

 

                                        ; Must also be enabled in modules.conf

                                        ; Rx audio/signalling channel. Choose ONLY 1 per node stanza

 

                                        ; Enable the selected channel driver in modules.conf !!!

rxchannel = dahdi/pseudo                ; No radio (hub)

; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB

; rxchannel = Pi/1                      ; Raspberry Pi PiTA

; rxchannel = Radio/usb_1999            ; USBRadio (DSP)

; rxchannel = Dahdi/1                   ; PCI Quad card

; rxchannel = Beagle/1                  ; BeagleBoard

rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP

; rxchannel = Voter/1999                ; RTCM device

 

 

duplex = 1                              ; 0 = Half duplex with no telemetry tones or hang time.

                                        ;     Special Case: Full duplex if linktolink is set to yes.

                                        ;     This mode is preferred when interfacing with an external multiport repeater controller.

                                        ;     Comment out idrecording and idtalkover to suppress IDs also

                                        ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio.

                                        ;     This mode is preferred when interfacing a simplex node.

                                        ; 2 = Full Duplex with telemetry tones and hang time.

                                        ;     This mode is preferred when interfacing a repeater.

                                        ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio.

                                        ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.

 

linktolink = no                         ; disables forcing physical half-duplex operation of main repeater while

                                        ; still keeping half-duplex semantics (optional)

 

linkmongain = 0                         ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received.

                                        ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db.

                                        ; If linkmongain set to a positive number monitored audio will increase by the set amount in db.

                                        ; The value of linkmongain is in db. The default value is 0 db.

 

erxgain = -3                            ; Echolink receive gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

etxgain = 3                             ; Echolink transmit gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

;eannmode = 1                           ; 1 = Say only node number on echolink connects (default = 1)

                                        ; 2 = say phonetic call sign only on echolink connects

                                        ; 3 = say phonetic call sign and node number on echolink connects

 

;controlstates = controlstates          ; system control state stanza

 

scheduler = schedule                    ; scheduler stanza

functions = functions                   ; Repeater Function stanza

phone_functions = functions             ; Phone Function stanza

link_functions = functions              ; Link Function stanza

 

telemetry = telemetry                   ; Telemetry stanza

morse = morse                           ; Morse stanza

wait_times = wait-times                 ; Wait times stanza

 

context = radio                         ; dialing context for phone

callerid = "Repeater" <0000000000>      ; callerid for phone calls

accountcode = RADIO                     ; account code (optional)

 

hangtime = 5000                         ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms)

althangtime = 4000                      ; longer squelch tail

totime = 180000                         ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

 

idrecording = |iWA4XYZ                  ; cording or morse string see http://ohnosec.org/drupal/node/87

idtalkover = |iWA4XYZ                   ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129

                                        ; See Telemetry section Example: idrecording = rpt/nodenames/1999

idtime = 540000                         ; id interval time (in ms) (optional) Default 5 minutes (300000 ms)

politeid = 30000                        ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)

 

unlinkedct = ct2                        ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none)

remotect = ct3                          ; remote linked courtesy tone (indicates a remote is in the list of links)

linkunkeyct = ct8                       ; sent when a transmission received over the link unkeys

;nolocallinkct = 0                      ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).

 

;connpgm = yourconnectprogram           ; Disabled. Execute a program you specify on connect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being connected to us (them)

;discpgm = yourdisconnectprogram        ; Disabled. Execute a program you specify on disconnect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being disconnected from us (them)

 

;lnkactenable = 0                       ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.

 

;lnkacttime = 1800                      ; Link activity timer time in seconds.

;lnkactmacro = *52                      ; Function to execute when link activity timer expires.

;lnkacttimerwarn = 30seconds            ; Message to play when the link activity timer has 30 seconds left.

 

;remote_inact_timeout =                 ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60)

;remote_timeout =                       ; Session time out for remote base. Set to 0 to disable. (60 * 60)

;remote_timeout_warning_freq =          ; 30

;remote_timeout_warning =               ; (3 * 60)

 

;nounkeyct = 0                          ; Set to a 1 to eliminate courtesy tones and associated delays.

 

holdofftelem = 0                        ; Hold off all telemetry when signal is present on receiver or from connected nodes

                                        ; except when an ID needs to be done and there is a signal coming from a connected node.

 

telemdefault = 0                        ; 0 = telemetry output off

                                        ; 1 = telemetry output on (default = 1)

                                        ; 2 = timed telemetry output on command execution and for a short time thereafter.

 

telemdynamic = 1                        ; 0 = disallow users to change the local telemetry setting with a COP command,

                                        ; 1 = Allow users to change the setting with a COP command. (default = 1)

 

;beaconing = 0                          ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)

 

parrotmode = 0                          ; 0 = Parrot Off (default = 0)

                                        ; 1 = Parrot On Command

                                        ; 2 = Parrot Always

                                        ; 3 = Parrot Once by Command

 

parrottime = 1000                       ; Set the amount of time in milliseconds

                                        ; to wait before parroting what was received

 

;rxnotch=1065,40                        ; (Optional) Notch a particular frequency for a specified

                                        ; b/w. app_rpt must have been compiled with

                                        ; the notch option

 

startup_macro =

 

; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign   ; Point to alternate nodename sound directory

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Need more information on these

 

;extnodes = extnodes-different  ; section in extnodefile containing dynamic node information (optional)

;extnodefile = /foo/nodes       ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional)

;extnodefile2 =                 ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes????

;nodenames = /foo/names         ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames

;archivedir = /tmp              ; defines and enables activity recording into specified directory (optional)

;monminblocks = 2048            ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)

 

;                               ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set

;                               ; to support tail messages. They can be omitted otherwise.

;tailmessagetime = 300000       ; Play a tail message every 5 mins

;tailsquashedtime = 30000       ; If squashed by another user,

;                               ; try again after 30 seconds

;tailmessagelist = msg1,msg2    ; list of messages to be played for tail message

 

; alt_functions

; ctgroup

; dphone_functions

; idtime

; iobase

; iospeed

; locallist

; mars          Remote Base

; memory

; nobusyout

; nodes

; nolocallinkct

; notelemtx

; outxlat

; parrot

; propagate_phonedtmf

; rptnode

; rptinactmacro  Macro to execute when inactivity timer expires

; rptinacttime   Inactivity timer time in seconds  (0 seconds disables feature)

; rxnotch       Optional Audio notch

; simplexphonedelay

; tonemacro

; tonezone

; txlimits

 

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

 

; *** Status Reporting ***

 

; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org

statpost_url = http://stats.allstarlink.org/uhandler ; Status updates

 

[functions]

 

; Prefix        Functions

; *1            Disconnect Link

; *2            Monitor Link

; *3            Connect Link

; *4            Command Mode

; *5            Macros

; *6            User Functions

; *7            Connection Status/Functions

; *8            User Functions

; *9            User Functions

; *0            User Functions

 

; *A            User Functions

; *B            User Functions

; *C            User Functions

; *D            User Functions

 

 

; Mandatory Command Codes

; http://docs.allstarlink.org/drupal/node/91

 

1 = ilink,1             ; Disconnect specified link

2 = ilink,2             ; Connect specified link -- monitor only

3 = ilink,3             ; Connect specified link -- tranceive

4 = ilink,4             ; Enter command mode on specified link

70 = ilink,5            ; System status

99 = cop,6              ; PTT (phone mode only)

 

; End Mandatory Command Codes

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Macro Commands

5 = macro

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Autopatch Commands

; Note, This may be a good place for other 2 digit frequently used commands

 

61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000  ; Autopatch up

62 = autopatchdn                                                 ; Autopatch down

 

; autopatchup can optionally take comma delimited setting=value pairs:

 

; context = string              ; Override default context with "string"

; dialtime = ms                 ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second)

; farenddisconnect = 1          ; Automatically disconnect when called party hangs up

; noct = 1                      ; Don't send repeater courtesy tone during autopatch calls

; quiet = 1                     ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up

                                ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Status Commands

 

; 1 - Force ID (global)

; 2 - Give Time of Day (global)

; 3 - Give software Version (global)

; 4 - Give GPS location info

; 5 - Last (dtmf) user

; 11 - Force ID (local only)

; 12 - Give Time of Day (local only)

 

721 = status,1          ; Force ID (global)

722 = status,2          ; Give Time of Day (global)

723 = status,3          ; Give software Version (global)

724 = status,4          ; Give GPS location info

725 = status,5          ; Last (dtmf) user

711 = status,11         ; Force ID (local only)

712 = status,12         ; Give Time of Day (local only)

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Link Commands

 

; 1 - Disconnect specified link

; 2 - Connect specified link -- monitor only

; 3 - Connect specified link -- tranceive

; 4 - Enter command mode on specified link

; 5 - System status

; 6 - Disconnect all links

; 7 - Last Node to Key Up

; 8 - Connect specified link -- local monitor only

; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.

; 10 - Disconnect all RANGER links (except permalinks)

; 11 - Disconnect a previously permanently connected link

; 12 - Permanently connect specified link -- monitor only

; 13 - Permanently connect specified link -- tranceive

; 15 - Full system status (all nodes)

; 16 - Reconnect links disconnected with "disconnect all links"

; 17 - MDC test (for diag purposes)

; 18 - Permanently Connect specified link -- local monitor only

 

; ilink commands 1 through 5 are defined in the Mandatory Command section

 

806 = ilink,6                   ; Disconnect all links

807 = ilink,7                   ; Last Node to Key Up

808 = ilink,8                   ; Connect specified link -- local monitor only

809 = ilink,9,1999,"Testing"    ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes

810 = ilink,10                  ; Disconnect all RANGER links (except permalinks)

811 = ilink,11                  ; Disconnect a previously permanently connected link

812 = ilink,12                  ; Permanently connect specified link -- monitor only

813 = ilink,13                  ; Permanently connect specified link -- tranceive

815 = ilink,15                  ; Full system status (all nodes)

816 = ilink,16                  ; Reconnect links disconnected with "disconnect all links"

817 = ilink,17                  ; MDC test (for diag purposes)

818 = ilink 18                  ; Permanently Connect specified link -- local monitor only

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Control operator (cop) functions. Change these to something other than these codes listed below!

 

901 = cop,1                   ��         ; System warm boot

902 = cop,2                             ; System enable

903 = cop,3                             ; System disable

 

904 = cop,4                             ; Test tone on/off (toggle)

905 = cop,5                             ; Dump system variables on console (debug use only)

 

907 = cop,7                             ; Time out timer enable

908 = cop,8                             ; Time out timer disable

 

909 = cop,9                             ; Autopatch enable

910 = cop,10                            ; Autopatch disable

 

911 = cop,11                            ; User linking functions enable

912 = cop,12                            ; User linking functions disable

 

913 = cop,13                            ; Query system control state

914 = cop,14                            ; Set system control state

 

915 = cop,15                            ; Scheduler enable

916 = cop,16                            ; Scheduler disable

 

917 = cop,17                            ; User functions enable (time, id, etc)

918 = cop,18                            ; User functions disable

 

919 = cop,19                            ; Select alternate hang time (althangtime)

920 = cop,20                            ; Select standard hangtime (hangtime)

 

921 = cop,21                            ; Enable Parrot Mode

922 = cop,22                            ; Disable Parrot Mode

923 = cop,23                            ; Birdbath (Current Parrot Cleanup/Flush)

 

924 = cop,24                            ; Flush all telemetry

925 = cop,25                            ; Query last node un-keyed

926 = cop,26                            ; Query all nodes keyed/unkeyed

927 = cop,27                            ; Reset DAQ minimum on a pin

928 = cop,28                            ; Reset DAQ maximum on a pin

 

930 = cop,30                            ; Recall Memory Setting in Attached Xcvr

 

931 = cop,31                            ; Channel Selector for Parallel Programmed Xcvr

 

932 = cop,32                            ; Touchtone pad test: command + Digit string + # to playback all digits pressed

 

933 = cop,33                            ; Local Telemetry Output Enable

934 = cop,34                            ; Local Telemetry Output Disable

935 = cop,35                            ; Local Telemetry Output on Demand

 

936 = cop,36                            ; Foreign Link Local Output Path Enable

937 = cop,37                            ; Foreign Link Local Output Path Disable

938 = cop,38                            ; Foreign Link Local Output Path Follows Local Telemetry

939 = cop,39                            ; Foreign Link Local Output Path on Demand

 

942 = cop,42                            ; Echolink announce node # only

943 = cop,43                            ; Echolink announce node Callsign only

944 = cop,44                            ; Echolink announce node # & Callsign

 

945 = cop,45                            ; Link Activity timer enable

945 = cop,46                            ; Link Activity timer disable

947 = cop,47                            ; Reset "Link Config Changed" Flag

 

948 = cop,48                            ; Send Page Tone (Tone specs separated by parenthesis)

 

949 = cop,49                            ; Disable incoming connections (control state noice)

950 = cop,50                            ; Enable incoming connections (control state noicd)

 

951 = cop,51                            ; Enable sleep mode

952 = cop,52                            ; Disable sleep mode

953 = cop,53                            ; Wake up from sleep

954 = cop,54                            ; Go to sleep

955 = cop,55                            ; Parrot Once if parrot mode is disabled

 

956 = cop,56                            ; Rx CTCSS Enable

957 = cop,57                            ; Rx CTCSS Disable

 

958 = cop.58                            ; Tx CTCSS On Input only Enable

959 = cop,59                            ; Tx CTCSS On Input only Disable

 

960 = cop,60                            ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])

                                        ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call

                                        ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.

                                        ; DestID and subcode are only specified for  the 'C' type message.

                                        ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of

                                        ; the radio being called, and the subcodes are as follows:

                                        ; Subcode '8205' is Voice Selective Call for Spectra ('Call')

                                        ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or

                                        ; Astro-Saber('Call')

                                        ; Subcode '810D' is Call Alert (like Maxtrac 'CA')

 

961 = cop,61                            ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)

962 = cop,62                            ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)

 

963 = cop,63                            ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])

964 = cop,64                            ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])

965 = cop,65                            ; Send POCSAG page (equipped channel types only)

 

[functions-remote]

 

0 = remote,1                            ; Retrieve Memory

1 = remote,2                            ; Set freq.

2 = remote,3                            ; Set tx PL tone

3 = remote,4                            ; Set rx PL tone

40 = remote,100                         ; Rx PL off

41 = remote,101                         ; Rx PL on

42 = remote,102                         ; Tx PL off

43 = remote,103                         ; Tx PL on

44 = remote,104                         ; Low Power

45 = remote,105                         ; Medium Power

46 = remote,106                         ; High Power

711 = remote,107                        ; Bump -20

714 = remote,108                        ; Bump -100

717 = remote,109                        ; Bump -500

713 = remote,110                        ; Bump +20

716 = remote,111                        ; Bump +100

719 = remote,112                        ; Bump +500

721 = remote,113                        ; Scan - slow

724 = remote,114                        ; Scan - quick

727 = remote,115                        ; Scan - fast

723 = remote,116                        ; Scan + slow

726 = remote,117                        ; Scan + quick

729 = remote,118                        ; Scan + fast

79 = remote,119                         ; Tune

51 = remote,5                           ; Long status query

52 = remote,140                         ; Short status query

67 = remote,210                         ; Send a *

69 = remote,211                         ; Send a #

;91 = remote,99,CALLSIGN,LICENSETAG     ; Remote base login.

                                        ; Define a different dtmf sequence for each user which is

                                        ; authorized to use the remote base to control access to it.

                                        ; For examble 9139583=remote,99,WB6NIL,G would grant access to

                                        ; the remote base and announce WB6NIL as being logged in.

                                        ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to

                                        ; the remote base and announce WA6ZFT as being logged in.

                                        ; When the remote base is disconnected from the originating node, the

                                        ; user will be logged out. The LICENSETAG argument is used to enforce

                                        ; tx frequency limits. See [txlimits] below.

85 = cop,6                              ; Remote base telephone key

 

 

[telemetry]

 

; Telemetry entries can be shared across all repeaters, or defined for each repeater.

; Can be a tone sequence, morse string, or a file

;

; |t - Tone escape sequence

;

; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)

; Single frequencies are created by setting freq1 or freq2 to zero.

;

; |m - Morse escape sequence

;

; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the

; [morse] section.

;

; Follow with an alphanumeric string

;

; |i - Morse ID escape sequence

;

; Sends Morse code at the ID amplitude and ID frequency as defined in the

; [morse] section.

;

; path/to/sound/file/without/extension

;

; Send the sound if in place of a constructed tone. Do not include the file extension

; Example: ct8 = rpt/bloop

; Example: idrecording = rpt/nodenames/1999

 

ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)

ct2 = |t(660,880,150,2048)

ct3 = |t(440,0,150,4096)

ct4 = |t(550,0,150,2048)

ct5 = |t(660,0,150,2048)

ct6 = |t(880,0,150,2048)

ct7 = |t(660,440,150,2048)

ct8 = |t(700,1100,150,2048)

ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)

remotemon = |t(1209,0,50,2048)                                  ; local courtesy tone when receive only

remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000)         ; local courtesy tone when linked Trancieve mode

cmdmode = |t(900,903,200,2048)

functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)

remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)

pfxtone = |t(350,440,30000,3072)

patchup = rpt/callproceeding

patchdown = rpt/callterminated

 

; As far as what the numbers mean,

; (000,000,010,000)

;   |   |   |   |-------amplitude

;   |   |   |-------------duration

;   |   |-------------------Tone 2

;   |-------------------------Tone 1

 

; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.

; Use it for a delay.  Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter)

; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.

 

; Morse code parameters, these are common to all repeaters.

 

[morse]

speed = 20                              ; Approximate speed in WPM

frequency = 800                         ; Morse Telemetry Frequency

amplitude = 4096                        ; Morse Telemetry Amplitude

idfrequency = 1065                      ; Morse ID Frequency

idamplitude = 1024                      ; Morse ID Amplitude

 

;

; This section allows wait times for telemetry events to be adjusted

; A section for wait times can be defined for every repeater

;

 

[wait-times]

telemwait = 2000                        ; Time to wait before sending most telemetry

idwait = 500                            ; Time to wait before starting ID

unkeywait = 2000                        ; Time to wait after unkey before sending CT's and link telemetry

calltermwait = 2000                     ; Time to wait before announcing "call terminated"

 

;

; This is where you define your nodes which cam be connected to.

;

 

[nodes]

; Note, if you are using automatic update for allstar link nodes,

; no allstar link nodes should be defined here. Only place a definition

; for your local nodes, and private (off of allstar link) nodes here.

 

460310 = radio@....0.1:4569/460310,NONE       ; This must be changed to your node number

                                        ; and iax port number if not the default

; Memories for remote bases

 

[memory]

;00 = 146.580,100.0,m

;01 = 147.030,103.5,m+t

;02 = 147.240,103.5,m+t

;03 = 147.765,79.7,m-t

;04 = 146.460,100.0,m

;05 = 146.550,100.0,m

 

; Place command macros here

 

[macro]

;1 = *32011#

;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#

;3 = *32001*32011*32050*32030*32060#

 

 

; Data Acquisition configuration

 

;[daq-list]

;device = device_name1

;device = device_name2

 

;Where: device_name1 and device_name2 are stanzas you define in this file

 

;device = daq-cham-1

 

; Device name

 

;[daq-cham-1]                           ; Defined in [daq-list]

;hwtype = uchameleon                    ; DAQ hardware type

;devnode = /dev/ttyUSB0                 ; DAQ device node (if required)

;1 = inadc                              ; Pin definition for an ADC channel

;2 = inadc

;3 = inadc

;4 = inadc

;5 = inadc

;6 = inadc

;7 = inadc

;8 = inadc

;9 = inp                                ; Pin definition for an input with a weak pullup resistor

;10 = inp

;11 = inp

;12 = inp

;13 = in                                ; Pin definition for an input without a weak pullup resistor

;14 = out                               ; Pin definition for an output

;15 = out

;16 = out

;17 = out

;18 = out

 

;[meter-faces]

 

;face = scale(scalepre,scalediv,scalepost),word/?,...

;

; scalepre = offset to add before dividing with scalediv

; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts).

; scalepost = offset to add after dividing with scalediv

;

;face = range(X-Y:word,X2-Y2:word,...),word/?,...

;face = bit(low-word,high-word),word/?,...

;

; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories,

; or a question mark which is  a placeholder for the measured value.

;

;

; Battery voltage 0-20 volts

;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts

; 4 quadrant wind direction

;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?

; LM34 temperature sensor with 130 deg. F full scale

;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit

; Status poll (non alarmed)

;light = bit(ha/off,ha/on),ha/light,?

 

;[alarms]

;

;tag = device,pin,node,ignorefirst,func-low,func-hi

;

;tag = a unique name for the alarm

;device = daq device to poll

;pin = the device pin to be monitored

;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it

;node = the node number to execute the function on

;func-low = the DTMF function to execute on a high to low transition

;func-high = the DTMF function to execute on a low to high transition

;

; a  '-' as a function name is shorthand for no-operation

;

;door = daq-cham-1,9,1,2017,*7,-

;pwrfail = daq-cham-1,10,0,2017,*911111,-

;

; Control states

; Allow several control operator functions to be changed at once using one command (good for scheduling)

;

;[controlstates]

;statenum = copcmd,[copcmd]...

;0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation

;1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation

;2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation

 

; Scheduler - execute a macro at a given time

 

[schedule]

;dtmf_function =  m h dom mon dow  ; ala cron, star is implied

;2 = 00 00 * * *   ; at midnight, execute macro 2.

 

#includeifexists custom/rpt.conf

 

 

 

 

Analog_Bridge.ini

 

 

; Analog_Bridge configuration file.

;   This file should be placed in either /etc or it can be

;   supplied as a path on the Analog_Bridge command line.

 

; The best way to think of this file is that there are two main sections, the USRP (analog audio) and

; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and

; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.

; As you might expect, the reverse direction is defined too.

 

; Analog_Bridge supports include files. More on this later...

include = dvsm.macro

; include = asl.macro

 

; General Section describes settings for Analog_Bridge itself.

[GENERAL]

logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal

 

; Metadata management

exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)

transferRootDir = /tmp                  ; Export database files to USRP partner

subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data

 

; General vocoder setup information

decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found

useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)

emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server

 

pcmPort = 2222                          ; UDP port to send to the WebProxy

 

; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)

[AMBE_AUDIO]

address = 127.0.0.1                     ; IP address of xx_Bridge

txPort = 31103                          ; Transmit TLV frames to partner on this port

rxPort = 31100                          ; Listen for TLV frames from partner on this port

ambeMode = DMR                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)

minTxTimeMS = 2500                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)

 

; The metadata below is used when ASL is the source since it does not have any concept of digital modes

gatewayDmrId = 1112721                  ; ID to use when transmitting from Analog_Bridge 7 digit ID

repeaterID = 111272123                  ; ID of source repeater 7 digit ID plus 2 digit SSID

txTg = 31676                               ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge

txTs = 2                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge

colorCode = 1                           ; Color Code to assign DMR frames

 

; Information for USRP channel driver.  This interface uses PCM to transfer audio information

; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected

; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself,

; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.

;   When using ASL, this matches the rpt.conf ASL file with a setting like:

;   rxchannel = usrp/127.0.0.1:34001:32001

;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch

;   each instance with its own ini file.

[USRP]

address = 127.0.0.1                     ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge)

txPort = 32001                          ; Transmit USRP frames on this port

rxPort = 34001                          ; Listen for USRP frames on this port

usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)

usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)

tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)

tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

 

[MACROS]

 

; Where the macros are

; xxxx=yyyy

; xxxx is the dial string to match

; yyyy is the command line to execute

 

; xxxx must be preceded by a *

; xxxx can be any string (alphanumeric)

; yyyy is the command to execute

; yyyy will replace xxxx in the dial string

; arguments follow the macro name with a # delimiter

 

; For example using macro "5678" above would look like:

; *5678#9876

 

; Which would invoke:

; echo 9876

 

; Information for DV3000 hardware decoder

;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)

;   Use top server and port if using AMBEServer

;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)

;   Did you run AMBETest4.py before using this?

[DV3000]

address = 127.0.0.1                   ; IP address of AMBEServer

rxPort = 2460                         ; Port of AMBEServer

; address = /dev/ttyUSB0              ; Device of DV3000U on this machine

; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)

; serial = true                       ; Use serial=true f

 

 

 

 

 

 



Steve Siesel [K4KSA]
 

Yes…..

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:50 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

Did you fix rpt.conf and did you then restart asterisk?

On 2/14/21 2:46 PM, Steve Siesel [K4KSA] wrote:

After restarting AB and Asterisk….also md3890-emu is running

Still no Joy…Here is the latest start of Analog_bridge.log

 

 

I: 2021-02-14 19:43:13.761 Analog_Bridge is starting

M: 2021-02-14 19:43:13.762 Setting [MACROS] DMR -> /opt/MMDVM_Bridge/dvswitch.sh mode DMR

M: 2021-02-14 19:43:13.762 Setting [MACROS] DSTAR -> /opt/MMDVM_Bridge/dvswitch.sh mode DSTAR

M: 2021-02-14 19:43:13.762 Setting [MACROS] NXDN -> /opt/MMDVM_Bridge/dvswitch.sh mode NXDN

M: 2021-02-14 19:43:13.762 Setting [MACROS] P25 -> /opt/MMDVM_Bridge/dvswitch.sh mode P25

M: 2021-02-14 19:43:13.762 Setting [MACROS] YSF -> /opt/MMDVM_Bridge/dvswitch.sh mode YSF

M: 2021-02-14 19:43:13.762 Setting [MACROS] dbupdate -> /opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles

M: 2021-02-14 19:43:13.764 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh

M: 2021-02-14 19:43:13.765 Setting [] include -> dvsm.macro

M: 2021-02-14 19:43:13.766 Setting [GENERAL] logLevel -> 2

M: 2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata -> true

M: 2021-02-14 19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp

M: 2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv

M: 2021-02-14 19:43:13.768 Setting [GENERAL] decoderFallBack -> true

M: 2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator -> false

M: 2021-02-14 19:43:13.769 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470

M: 2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort -> 2222

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1

M: 2021-02-14 19:43:13.773 Setting [USRP] address -> 127.0.0.1

M: 2021-02-14 19:43:13.773 Setting [USRP] txPort -> 32001

M: 2021-02-14 19:43:13.773 Setting [USRP] rxPort -> 34001

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpGain -> 1.10

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvGain -> 0.35

M: 2021-02-14 19:43:13.776 Setting [DV3000] address -> 127.0.0.1

M: 2021-02-14 19:43:13.776 Setting [DV3000] rxPort -> 2460

I: 2021-02-14 19:43:13.777 Open UDP listener on 127.0.0.1:31100

I: 2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001

M: 2021-02-14 19:43:13.777 Connecting to DV3000 hardware......

W: 2021-02-14 19:43:13.871 DV3000 did not reset at 127.0.0.1:2460

W: 2021-02-14 19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset failed)

I: 2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850

I: 2021-02-14 19:43:16.073 Default extended metadata <K4KSA>

W: 2021-02-14 19:43:16.073 Using software MBE decoder version 1.2.3

W: 2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE vocoder

I: 2021-02-14 19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s) 32001

I: 2021-02-14 19:43:16.074 Sending PCM to  clients at 127.0.0.1 on port 2222

I: 2021-02-14 19:43:16.074 Starting TLV --> Analog_Bridge (decoder) --> USRP thread

I: 2021-02-14 19:43:16.075 Starting USRP --> Analog_Bridge (encoder) -> TLV thread

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:41 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

You have 2 channel drivers uncommented:

rxchannel = dahdi/pseudo                ; No radio (hub) <--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB
; rxchannel = Pi/1                      ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999            ; USBRadio (DSP)
; rxchannel = Dahdi/1                   ; PCI Quad card
; rxchannel = Beagle/1                  ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999                ; RTCM device

On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote:

Can you look at this as well…..

 

I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that.

 

Steve

 

 

; Your Repeater

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

[460310]                                        ; Change this to your assigned node number

 

                                        ; Must also be enabled in modules.conf

                                        ; Rx audio/signalling channel. Choose ONLY 1 per node stanza

 

                                        ; Enable the selected channel driver in modules.conf !!!

rxchannel = dahdi/pseudo                ; No radio (hub)

; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB

; rxchannel = Pi/1                      ; Raspberry Pi PiTA

; rxchannel = Radio/usb_1999            ; USBRadio (DSP)

; rxchannel = Dahdi/1                   ; PCI Quad card

; rxchannel = Beagle/1                  ; BeagleBoard

rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP

; rxchannel = Voter/1999                ; RTCM device

 

 

duplex = 1                              ; 0 = Half duplex with no telemetry tones or hang time.

                                        ;     Special Case: Full duplex if linktolink is set to yes.

                                        ;     This mode is preferred when interfacing with an external multiport repeater controller.

                                        ;     Comment out idrecording and idtalkover to suppress IDs also

                                        ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio.

                                        ;     This mode is preferred when interfacing a simplex node.

                                        ; 2 = Full Duplex with telemetry tones and hang time.

                                        ;     This mode is preferred when interfacing a repeater.

                                        ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio.

                                        ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.

 

linktolink = no                         ; disables forcing physical half-duplex operation of main repeater while

                                        ; still keeping half-duplex semantics (optional)

 

linkmongain = 0                         ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received.

                                        ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db.

                                        ; If linkmongain set to a positive number monitored audio will increase by the set amount in db.

                                        ; The value of linkmongain is in db. The default value is 0 db.

 

erxgain = -3                            ; Echolink receive gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

etxgain = 3                             ; Echolink transmit gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

;eannmode = 1                           ; 1 = Say only node number on echolink connects (default = 1)

                                        ; 2 = say phonetic call sign only on echolink connects

                                        ; 3 = say phonetic call sign and node number on echolink connects

 

;controlstates = controlstates          ; system control state stanza

 

scheduler = schedule                    ; scheduler stanza

functions = functions                   ; Repeater Function stanza

phone_functions = functions             ; Phone Function stanza

link_functions = functions              ; Link Function stanza

 

telemetry = telemetry                   ; Telemetry stanza

morse = morse                           ; Morse stanza

wait_times = wait-times                 ; Wait times stanza

 

context = radio                         ; dialing context for phone

callerid = "Repeater" <0000000000>      ; callerid for phone calls

accountcode = RADIO                     ; account code (optional)

 

hangtime = 5000                         ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms)

althangtime = 4000                      ; longer squelch tail

totime = 180000                         ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

 

idrecording = |iWA4XYZ                  ; cording or morse string see http://ohnosec.org/drupal/node/87

idtalkover = |iWA4XYZ                   ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129

                                        ; See Telemetry section Example: idrecording = rpt/nodenames/1999

idtime = 540000                         ; id interval time (in ms) (optional) Default 5 minutes (300000 ms)

politeid = 30000                        ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)

 

unlinkedct = ct2                        ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none)

remotect = ct3                          ; remote linked courtesy tone (indicates a remote is in the list of links)

linkunkeyct = ct8                       ; sent when a transmission received over the link unkeys

;nolocallinkct = 0                      ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).

 

;connpgm = yourconnectprogram           ; Disabled. Execute a program you specify on connect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being connected to us (them)

;discpgm = yourdisconnectprogram        ; Disabled. Execute a program you specify on disconnect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being disconnected from us (them)

 

;lnkactenable = 0                       ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.

 

;lnkacttime = 1800                      ; Link activity timer time in seconds.

;lnkactmacro = *52                      ; Function to execute when link activity timer expires.

;lnkacttimerwarn = 30seconds            ; Message to play when the link activity timer has 30 seconds left.

 

;remote_inact_timeout =                 ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60)

;remote_timeout =                       ; Session time out for remote base. Set to 0 to disable. (60 * 60)

;remote_timeout_warning_freq =          ; 30

;remote_timeout_warning =               ; (3 * 60)

 

;nounkeyct = 0                          ; Set to a 1 to eliminate courtesy tones and associated delays.

 

holdofftelem = 0                        ; Hold off all telemetry when signal is present on receiver or from connected nodes

                                        ; except when an ID needs to be done and there is a signal coming from a connected node.

 

telemdefault = 0                        ; 0 = telemetry output off

                                        ; 1 = telemetry output on (default = 1)

                                        ; 2 = timed telemetry output on command execution and for a short time thereafter.

 

telemdynamic = 1                        ; 0 = disallow users to change the local telemetry setting with a COP command,

                                        ; 1 = Allow users to change the setting with a COP command. (default = 1)

 

;beaconing = 0                          ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)

 

parrotmode = 0                          ; 0 = Parrot Off (default = 0)

                                        ; 1 = Parrot On Command

                                        ; 2 = Parrot Always

                                        ; 3 = Parrot Once by Command

 

parrottime = 1000                       ; Set the amount of time in milliseconds

                                        ; to wait before parroting what was received

 

;rxnotch=1065,40                        ; (Optional) Notch a particular frequency for a specified

                                        ; b/w. app_rpt must have been compiled with

                                        ; the notch option

 

startup_macro =

 

; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign   ; Point to alternate nodename sound directory

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Need more information on these

 

;extnodes = extnodes-different  ; section in extnodefile containing dynamic node information (optional)

;extnodefile = /foo/nodes       ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional)

;extnodefile2 =                 ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes????

;nodenames = /foo/names         ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames

;archivedir = /tmp              ; defines and enables activity recording into specified directory (optional)

;monminblocks = 2048            ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)

 

;                               ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set

;                               ; to support tail messages. They can be omitted otherwise.

;tailmessagetime = 300000       ; Play a tail message every 5 mins

;tailsquashedtime = 30000       ; If squashed by another user,

;                               ; try again after 30 seconds

;tailmessagelist = msg1,msg2    ; list of messages to be played for tail message

 

; alt_functions

; ctgroup

; dphone_functions

; idtime

; iobase

; iospeed

; locallist

; mars          Remote Base

; memory

; nobusyout

; nodes

; nolocallinkct

; notelemtx

; outxlat

; parrot

; propagate_phonedtmf

; rptnode

; rptinactmacro  Macro to execute when inactivity timer expires

; rptinacttime   Inactivity timer time in seconds  (0 seconds disables feature)

; rxnotch       Optional Audio notch

; simplexphonedelay

; tonemacro

; tonezone

; txlimits

 

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

 

; *** Status Reporting ***

 

; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org

statpost_url = http://stats.allstarlink.org/uhandler ; Status updates

 

[functions]

 

; Prefix        Functions

; *1            Disconnect Link

; *2            Monitor Link

; *3            Connect Link

; *4            Command Mode

; *5            Macros

; *6            User Functions

; *7            Connection Status/Functions

; *8            User Functions

; *9            User Functions

; *0            User Functions

 

; *A            User Functions

; *B            User Functions

; *C            User Functions

; *D            User Functions

 

 

; Mandatory Command Codes

; http://docs.allstarlink.org/drupal/node/91

 

1 = ilink,1             ; Disconnect specified link

2 = ilink,2             ; Connect specified link -- monitor only

3 = ilink,3             ; Connect specified link -- tranceive

4 = ilink,4             ; Enter command mode on specified link

70 = ilink,5            ; System status

99 = cop,6              ; PTT (phone mode only)

 

; End Mandatory Command Codes

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Macro Commands

5 = macro

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Autopatch Commands

; Note, This may be a good place for other 2 digit frequently used commands

 

61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000  ; Autopatch up

62 = autopatchdn                                                 ; Autopatch down

 

; autopatchup can optionally take comma delimited setting=value pairs:

 

; context = string              ; Override default context with "string"

; dialtime = ms                 ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second)

; farenddisconnect = 1          ; Automatically disconnect when called party hangs up

; noct = 1                      ; Don't send repeater courtesy tone during autopatch calls

; quiet = 1                     ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up

                                ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Status Commands

 

; 1 - Force ID (global)

; 2 - Give Time of Day (global)

; 3 - Give software Version (global)

; 4 - Give GPS location info

; 5 - Last (dtmf) user

; 11 - Force ID (local only)

; 12 - Give Time of Day (local only)

 

721 = status,1          ; Force ID (global)

722 = status,2          ; Give Time of Day (global)

723 = status,3          ; Give software Version (global)

724 = status,4          ; Give GPS location info

725 = status,5          ; Last (dtmf) user

711 = status,11         ; Force ID (local only)

712 = status,12         ; Give Time of Day (local only)

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Link Commands

 

; 1 - Disconnect specified link

; 2 - Connect specified link -- monitor only

; 3 - Connect specified link -- tranceive

; 4 - Enter command mode on specified link

; 5 - System status

; 6 - Disconnect all links

; 7 - Last Node to Key Up

; 8 - Connect specified link -- local monitor only

; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.

; 10 - Disconnect all RANGER links (except permalinks)

; 11 - Disconnect a previously permanently connected link

; 12 - Permanently connect specified link -- monitor only

; 13 - Permanently connect specified link -- tranceive

; 15 - Full system status (all nodes)

; 16 - Reconnect links disconnected with "disconnect all links"

; 17 - MDC test (for diag purposes)

; 18 - Permanently Connect specified link -- local monitor only

 

; ilink commands 1 through 5 are defined in the Mandatory Command section

 

806 = ilink,6                   ; Disconnect all links

807 = ilink,7                   ; Last Node to Key Up

808 = ilink,8                   ; Connect specified link -- local monitor only

809 = ilink,9,1999,"Testing"    ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes

810 = ilink,10                  ; Disconnect all RANGER links (except permalinks)

811 = ilink,11                  ; Disconnect a previously permanently connected link

812 = ilink,12                  ; Permanently connect specified link -- monitor only

813 = ilink,13                  ; Permanently connect specified link -- tranceive

815 = ilink,15                  ; Full system status (all nodes)

816 = ilink,16                  ; Reconnect links disconnected with "disconnect all links"

817 = ilink,17                  ; MDC test (for diag purposes)

818 = ilink 18                  ; Permanently Connect specified link -- local monitor only

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Control operator (cop) functions. Change these to something other than these codes listed below!

 

901 = cop,1                   ��         ; System warm boot

902 = cop,2                             ; System enable

903 = cop,3                             ; System disable

 

904 = cop,4                             ; Test tone on/off (toggle)

905 = cop,5                             ; Dump system variables on console (debug use only)

 

907 = cop,7                             ; Time out timer enable

908 = cop,8                             ; Time out timer disable

 

909 = cop,9                             ; Autopatch enable

910 = cop,10                            ; Autopatch disable

 

911 = cop,11                            ; User linking functions enable

912 = cop,12                            ; User linking functions disable

 

913 = cop,13                            ; Query system control state

914 = cop,14                            ; Set system control state

 

915 = cop,15                            ; Scheduler enable

916 = cop,16                            ; Scheduler disable

 

917 = cop,17                            ; User functions enable (time, id, etc)

918 = cop,18                            ; User functions disable

 

919 = cop,19                            ; Select alternate hang time (althangtime)

920 = cop,20                            ; Select standard hangtime (hangtime)

 

921 = cop,21                            ; Enable Parrot Mode

922 = cop,22                            ; Disable Parrot Mode

923 = cop,23                            ; Birdbath (Current Parrot Cleanup/Flush)

 

924 = cop,24                            ; Flush all telemetry

925 = cop,25                            ; Query last node un-keyed

926 = cop,26                            ; Query all nodes keyed/unkeyed

927 = cop,27                            ; Reset DAQ minimum on a pin

928 = cop,28                            ; Reset DAQ maximum on a pin

 

930 = cop,30                            ; Recall Memory Setting in Attached Xcvr

 

931 = cop,31                            ; Channel Selector for Parallel Programmed Xcvr

 

932 = cop,32                            ; Touchtone pad test: command + Digit string + # to playback all digits pressed

 

933 = cop,33                            ; Local Telemetry Output Enable

934 = cop,34                            ; Local Telemetry Output Disable

935 = cop,35                            ; Local Telemetry Output on Demand

 

936 = cop,36                            ; Foreign Link Local Output Path Enable

937 = cop,37                            ; Foreign Link Local Output Path Disable

938 = cop,38                            ; Foreign Link Local Output Path Follows Local Telemetry

939 = cop,39                            ; Foreign Link Local Output Path on Demand

 

942 = cop,42                            ; Echolink announce node # only

943 = cop,43                            ; Echolink announce node Callsign only

944 = cop,44                            ; Echolink announce node # & Callsign

 

945 = cop,45                            ; Link Activity timer enable

945 = cop,46                            ; Link Activity timer disable

947 = cop,47                            ; Reset "Link Config Changed" Flag

 

948 = cop,48                            ; Send Page Tone (Tone specs separated by parenthesis)

 

949 = cop,49                            ; Disable incoming connections (control state noice)

950 = cop,50                            ; Enable incoming connections (control state noicd)

 

951 = cop,51                            ; Enable sleep mode

952 = cop,52                            ; Disable sleep mode

953 = cop,53                            ; Wake up from sleep

954 = cop,54                            ; Go to sleep

955 = cop,55                            ; Parrot Once if parrot mode is disabled

 

956 = cop,56                            ; Rx CTCSS Enable

957 = cop,57                            ; Rx CTCSS Disable

 

958 = cop.58                            ; Tx CTCSS On Input only Enable

959 = cop,59                            ; Tx CTCSS On Input only Disable

 

960 = cop,60                            ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])

                                        ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call

                                        ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.

                                        ; DestID and subcode are only specified for  the 'C' type message.

                                        ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of

                                        ; the radio being called, and the subcodes are as follows:

                                        ; Subcode '8205' is Voice Selective Call for Spectra ('Call')

                                        ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or

                                        ; Astro-Saber('Call')

                                        ; Subcode '810D' is Call Alert (like Maxtrac 'CA')

 

961 = cop,61                            ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)

962 = cop,62                            ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)

 

963 = cop,63                            ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])

964 = cop,64                            ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])

965 = cop,65                            ; Send POCSAG page (equipped channel types only)

 

[functions-remote]

 

0 = remote,1                            ; Retrieve Memory

1 = remote,2                            ; Set freq.

2 = remote,3                            ; Set tx PL tone

3 = remote,4                            ; Set rx PL tone

40 = remote,100                         ; Rx PL off

41 = remote,101                         ; Rx PL on

42 = remote,102                         ; Tx PL off

43 = remote,103                         ; Tx PL on

44 = remote,104                         ; Low Power

45 = remote,105                         ; Medium Power

46 = remote,106                         ; High Power

711 = remote,107                        ; Bump -20

714 = remote,108                        ; Bump -100

717 = remote,109                        ; Bump -500

713 = remote,110                        ; Bump +20

716 = remote,111                        ; Bump +100

719 = remote,112                        ; Bump +500

721 = remote,113                        ; Scan - slow

724 = remote,114                        ; Scan - quick

727 = remote,115                        ; Scan - fast

723 = remote,116                        ; Scan + slow

726 = remote,117                        ; Scan + quick

729 = remote,118                        ; Scan + fast

79 = remote,119                         ; Tune

51 = remote,5                           ; Long status query

52 = remote,140                         ; Short status query

67 = remote,210                         ; Send a *

69 = remote,211                         ; Send a #

;91 = remote,99,CALLSIGN,LICENSETAG     ; Remote base login.

                                        ; Define a different dtmf sequence for each user which is

                                        ; authorized to use the remote base to control access to it.

                                        ; For examble 9139583=remote,99,WB6NIL,G would grant access to

                                        ; the remote base and announce WB6NIL as being logged in.

                                        ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to

                                        ; the remote base and announce WA6ZFT as being logged in.

                                        ; When the remote base is disconnected from the originating node, the

                                        ; user will be logged out. The LICENSETAG argument is used to enforce

                                        ; tx frequency limits. See [txlimits] below.

85 = cop,6                              ; Remote base telephone key

 

 

[telemetry]

 

; Telemetry entries can be shared across all repeaters, or defined for each repeater.

; Can be a tone sequence, morse string, or a file

;

; |t - Tone escape sequence

;

; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)

; Single frequencies are created by setting freq1 or freq2 to zero.

;

; |m - Morse escape sequence

;

; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the

; [morse] section.

;

; Follow with an alphanumeric string

;

; |i - Morse ID escape sequence

;

; Sends Morse code at the ID amplitude and ID frequency as defined in the

; [morse] section.

;

; path/to/sound/file/without/extension

;

; Send the sound if in place of a constructed tone. Do not include the file extension

; Example: ct8 = rpt/bloop

; Example: idrecording = rpt/nodenames/1999

 

ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)

ct2 = |t(660,880,150,2048)

ct3 = |t(440,0,150,4096)

ct4 = |t(550,0,150,2048)

ct5 = |t(660,0,150,2048)

ct6 = |t(880,0,150,2048)

ct7 = |t(660,440,150,2048)

ct8 = |t(700,1100,150,2048)

ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)

remotemon = |t(1209,0,50,2048)                                  ; local courtesy tone when receive only

remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000)         ; local courtesy tone when linked Trancieve mode

cmdmode = |t(900,903,200,2048)

functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)

remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)

pfxtone = |t(350,440,30000,3072)

patchup = rpt/callproceeding

patchdown = rpt/callterminated

 

; As far as what the numbers mean,

; (000,000,010,000)

;   |   |   |   |-------amplitude

;   |   |   |-------------duration

;   |   |-------------------Tone 2

;   |-------------------------Tone 1

 

; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.

; Use it for a delay.  Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter)

; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.

 

; Morse code parameters, these are common to all repeaters.

 

[morse]

speed = 20                              ; Approximate speed in WPM

frequency = 800                         ; Morse Telemetry Frequency

amplitude = 4096                        ; Morse Telemetry Amplitude

idfrequency = 1065                      ; Morse ID Frequency

idamplitude = 1024                      ; Morse ID Amplitude

 

;

; This section allows wait times for telemetry events to be adjusted

; A section for wait times can be defined for every repeater

;

 

[wait-times]

telemwait = 2000                        ; Time to wait before sending most telemetry

idwait = 500                            ; Time to wait before starting ID

unkeywait = 2000                        ; Time to wait after unkey before sending CT's and link telemetry

calltermwait = 2000                     ; Time to wait before announcing "call terminated"

 

;

; This is where you define your nodes which cam be connected to.

;

 

[nodes]

; Note, if you are using automatic update for allstar link nodes,

; no allstar link nodes should be defined here. Only place a definition

; for your local nodes, and private (off of allstar link) nodes here.

 

460310 = radio@....0.1:4569/460310,NONE       ; This must be changed to your node number

                                        ; and iax port number if not the default

; Memories for remote bases

 

[memory]

;00 = 146.580,100.0,m

;01 = 147.030,103.5,m+t

;02 = 147.240,103.5,m+t

;03 = 147.765,79.7,m-t

;04 = 146.460,100.0,m

;05 = 146.550,100.0,m

 

; Place command macros here

 

[macro]

;1 = *32011#

;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#

;3 = *32001*32011*32050*32030*32060#

 

 

; Data Acquisition configuration

 

;[daq-list]

;device = device_name1

;device = device_name2

 

;Where: device_name1 and device_name2 are stanzas you define in this file

 

;device = daq-cham-1

 

; Device name

 

;[daq-cham-1]                           ; Defined in [daq-list]

;hwtype = uchameleon                    ; DAQ hardware type

;devnode = /dev/ttyUSB0                 ; DAQ device node (if required)

;1 = inadc                              ; Pin definition for an ADC channel

;2 = inadc

;3 = inadc

;4 = inadc

;5 = inadc

;6 = inadc

;7 = inadc

;8 = inadc

;9 = inp                                ; Pin definition for an input with a weak pullup resistor

;10 = inp

;11 = inp

;12 = inp

;13 = in                                ; Pin definition for an input without a weak pullup resistor

;14 = out                               ; Pin definition for an output

;15 = out

;16 = out

;17 = out

;18 = out

 

;[meter-faces]

 

;face = scale(scalepre,scalediv,scalepost),word/?,...

;

; scalepre = offset to add before dividing with scalediv

; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts).

; scalepost = offset to add after dividing with scalediv

;

;face = range(X-Y:word,X2-Y2:word,...),word/?,...

;face = bit(low-word,high-word),word/?,...

;

; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories,

; or a question mark which is  a placeholder for the measured value.

;

;

; Battery voltage 0-20 volts

;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts

; 4 quadrant wind direction

;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?

; LM34 temperature sensor with 130 deg. F full scale

;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit

; Status poll (non alarmed)

;light = bit(ha/off,ha/on),ha/light,?

 

;[alarms]

;

;tag = device,pin,node,ignorefirst,func-low,func-hi

;

;tag = a unique name for the alarm

;device = daq device to poll

;pin = the device pin to be monitored

;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it

;node = the node number to execute the function on

;func-low = the DTMF function to execute on a high to low transition

;func-high = the DTMF function to execute on a low to high transition

;

; a  '-' as a function name is shorthand for no-operation

;

;door = daq-cham-1,9,1,2017,*7,-

;pwrfail = daq-cham-1,10,0,2017,*911111,-

;

; Control states

; Allow several control operator functions to be changed at once using one command (good for scheduling)

;

;[controlstates]

;statenum = copcmd,[copcmd]...

;0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation

;1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation

;2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation

 

; Scheduler - execute a macro at a given time

 

[schedule]

;dtmf_function =  m h dom mon dow  ; ala cron, star is implied

;2 = 00 00 * * *   ; at midnight, execute macro 2.

 

#includeifexists custom/rpt.conf

 

 

 

 

Analog_Bridge.ini

 

 

; Analog_Bridge configuration file.

;   This file should be placed in either /etc or it can be

;   supplied as a path on the Analog_Bridge command line.

 

; The best way to think of this file is that there are two main sections, the USRP (analog audio) and

; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and

; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.

; As you might expect, the reverse direction is defined too.

 

; Analog_Bridge supports include files. More on this later...

include = dvsm.macro

; include = asl.macro

 

; General Section describes settings for Analog_Bridge itself.

[GENERAL]

logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal

 

; Metadata management

exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)

transferRootDir = /tmp                  ; Export database files to USRP partner

subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data

 

; General vocoder setup information

decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found

useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)

emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server

 

pcmPort = 2222                          ; UDP port to send to the WebProxy

 

; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)

[AMBE_AUDIO]

address = 127.0.0.1                     ; IP address of xx_Bridge

txPort = 31103                          ; Transmit TLV frames to partner on this port

rxPort = 31100                          ; Listen for TLV frames from partner on this port

ambeMode = DMR                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)

minTxTimeMS = 2500                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)

 

; The metadata below is used when ASL is the source since it does not have any concept of digital modes

gatewayDmrId = 1112721                  ; ID to use when transmitting from Analog_Bridge 7 digit ID

repeaterID = 111272123                  ; ID of source repeater 7 digit ID plus 2 digit SSID

txTg = 31676                               ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge

txTs = 2                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge

colorCode = 1                           ; Color Code to assign DMR frames

 

; Information for USRP channel driver.  This interface uses PCM to transfer audio information

; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected

; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself,

; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.

;   When using ASL, this matches the rpt.conf ASL file with a setting like:

;   rxchannel = usrp/127.0.0.1:34001:32001

;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch

;   each instance with its own ini file.

[USRP]

address = 127.0.0.1                     ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge)

txPort = 32001                          ; Transmit USRP frames on this port

rxPort = 34001                          ; Listen for USRP frames on this port

usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)

usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)

tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)

tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

 

[MACROS]

 

; Where the macros are

; xxxx=yyyy

; xxxx is the dial string to match

; yyyy is the command line to execute

 

; xxxx must be preceded by a *

; xxxx can be any string (alphanumeric)

; yyyy is the command to execute

; yyyy will replace xxxx in the dial string

; arguments follow the macro name with a # delimiter

 

; For example using macro "5678" above would look like:

; *5678#9876

 

; Which would invoke:

; echo 9876

 

; Information for DV3000 hardware decoder

;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)

;   Use top server and port if using AMBEServer

;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)

;   Did you run AMBETest4.py before using this?

[DV3000]

address = 127.0.0.1                   ; IP address of AMBEServer

rxPort = 2460                         ; Port of AMBEServer

; address = /dev/ttyUSB0              ; Device of DV3000U on this machine

; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)

; serial = true                       ; Use serial=true f

 

 

 

 

 

 


Steve N4IRS
 

Did you fix rpt.conf and did you then restart asterisk?

On 2/14/21 2:46 PM, Steve Siesel [K4KSA] wrote:

After restarting AB and Asterisk….also md3890-emu is running

Still no Joy…Here is the latest start of Analog_bridge.log

 

 

I: 2021-02-14 19:43:13.761 Analog_Bridge is starting

M: 2021-02-14 19:43:13.762 Setting [MACROS] DMR -> /opt/MMDVM_Bridge/dvswitch.sh mode DMR

M: 2021-02-14 19:43:13.762 Setting [MACROS] DSTAR -> /opt/MMDVM_Bridge/dvswitch.sh mode DSTAR

M: 2021-02-14 19:43:13.762 Setting [MACROS] NXDN -> /opt/MMDVM_Bridge/dvswitch.sh mode NXDN

M: 2021-02-14 19:43:13.762 Setting [MACROS] P25 -> /opt/MMDVM_Bridge/dvswitch.sh mode P25

M: 2021-02-14 19:43:13.762 Setting [MACROS] YSF -> /opt/MMDVM_Bridge/dvswitch.sh mode YSF

M: 2021-02-14 19:43:13.762 Setting [MACROS] dbupdate -> /opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles

M: 2021-02-14 19:43:13.764 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh

M: 2021-02-14 19:43:13.765 Setting [] include -> dvsm.macro

M: 2021-02-14 19:43:13.766 Setting [GENERAL] logLevel -> 2

M: 2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata -> true

M: 2021-02-14 19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp

M: 2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv

M: 2021-02-14 19:43:13.768 Setting [GENERAL] decoderFallBack -> true

M: 2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator -> false

M: 2021-02-14 19:43:13.769 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470

M: 2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort -> 2222

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1

M: 2021-02-14 19:43:13.773 Setting [USRP] address -> 127.0.0.1

M: 2021-02-14 19:43:13.773 Setting [USRP] txPort -> 32001

M: 2021-02-14 19:43:13.773 Setting [USRP] rxPort -> 34001

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpGain -> 1.10

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvGain -> 0.35

M: 2021-02-14 19:43:13.776 Setting [DV3000] address -> 127.0.0.1

M: 2021-02-14 19:43:13.776 Setting [DV3000] rxPort -> 2460

I: 2021-02-14 19:43:13.777 Open UDP listener on 127.0.0.1:31100

I: 2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001

M: 2021-02-14 19:43:13.777 Connecting to DV3000 hardware......

W: 2021-02-14 19:43:13.871 DV3000 did not reset at 127.0.0.1:2460

W: 2021-02-14 19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset failed)

I: 2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850

I: 2021-02-14 19:43:16.073 Default extended metadata <K4KSA>

W: 2021-02-14 19:43:16.073 Using software MBE decoder version 1.2.3

W: 2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE vocoder

I: 2021-02-14 19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s) 32001

I: 2021-02-14 19:43:16.074 Sending PCM to  clients at 127.0.0.1 on port 2222

I: 2021-02-14 19:43:16.074 Starting TLV --> Analog_Bridge (decoder) --> USRP thread

I: 2021-02-14 19:43:16.075 Starting USRP --> Analog_Bridge (encoder) -> TLV thread

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:41 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

You have 2 channel drivers uncommented:

rxchannel = dahdi/pseudo                ; No radio (hub) <--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB
; rxchannel = Pi/1                      ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999            ; USBRadio (DSP)
; rxchannel = Dahdi/1                   ; PCI Quad card
; rxchannel = Beagle/1                  ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999                ; RTCM device

On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote:

Can you look at this as well…..

 

I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that.

 

Steve

 

 

; Your Repeater

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

[460310]                                        ; Change this to your assigned node number

 

                                        ; Must also be enabled in modules.conf

                                        ; Rx audio/signalling channel. Choose ONLY 1 per node stanza

 

                                        ; Enable the selected channel driver in modules.conf !!!

rxchannel = dahdi/pseudo                ; No radio (hub)

; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB

; rxchannel = Pi/1                      ; Raspberry Pi PiTA

; rxchannel = Radio/usb_1999            ; USBRadio (DSP)

; rxchannel = Dahdi/1                   ; PCI Quad card

; rxchannel = Beagle/1                  ; BeagleBoard

rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP

; rxchannel = Voter/1999                ; RTCM device

 

 

duplex = 1                              ; 0 = Half duplex with no telemetry tones or hang time.

                                        ;     Special Case: Full duplex if linktolink is set to yes.

                                        ;     This mode is preferred when interfacing with an external multiport repeater controller.

                                        ;     Comment out idrecording and idtalkover to suppress IDs also

                                        ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio.

                                        ;     This mode is preferred when interfacing a simplex node.

                                        ; 2 = Full Duplex with telemetry tones and hang time.

                                        ;     This mode is preferred when interfacing a repeater.

                                        ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio.

                                        ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.

 

linktolink = no                         ; disables forcing physical half-duplex operation of main repeater while

                                        ; still keeping half-duplex semantics (optional)

 

linkmongain = 0                         ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received.

                                        ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db.

                                        ; If linkmongain set to a positive number monitored audio will increase by the set amount in db.

                                        ; The value of linkmongain is in db. The default value is 0 db.

 

erxgain = -3                            ; Echolink receive gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

etxgain = 3                             ; Echolink transmit gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

;eannmode = 1                           ; 1 = Say only node number on echolink connects (default = 1)

                                        ; 2 = say phonetic call sign only on echolink connects

                                        ; 3 = say phonetic call sign and node number on echolink connects

 

;controlstates = controlstates          ; system control state stanza

 

scheduler = schedule                    ; scheduler stanza

functions = functions                   ; Repeater Function stanza

phone_functions = functions             ; Phone Function stanza

link_functions = functions              ; Link Function stanza

 

telemetry = telemetry                   ; Telemetry stanza

morse = morse                           ; Morse stanza

wait_times = wait-times                 ; Wait times stanza

 

context = radio                         ; dialing context for phone

callerid = "Repeater" <0000000000>      ; callerid for phone calls

accountcode = RADIO                     ; account code (optional)

 

hangtime = 5000                         ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms)

althangtime = 4000                      ; longer squelch tail

totime = 180000                         ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

 

idrecording = |iWA4XYZ                  ; cording or morse string see http://ohnosec.org/drupal/node/87

idtalkover = |iWA4XYZ                   ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129

                                        ; See Telemetry section Example: idrecording = rpt/nodenames/1999

idtime = 540000                         ; id interval time (in ms) (optional) Default 5 minutes (300000 ms)

politeid = 30000                        ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)

 

unlinkedct = ct2                        ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none)

remotect = ct3                          ; remote linked courtesy tone (indicates a remote is in the list of links)

linkunkeyct = ct8                       ; sent when a transmission received over the link unkeys

;nolocallinkct = 0                      ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).

 

;connpgm = yourconnectprogram           ; Disabled. Execute a program you specify on connect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being connected to us (them)

;discpgm = yourdisconnectprogram        ; Disabled. Execute a program you specify on disconnect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being disconnected from us (them)

 

;lnkactenable = 0                       ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.

 

;lnkacttime = 1800                      ; Link activity timer time in seconds.

;lnkactmacro = *52                      ; Function to execute when link activity timer expires.

;lnkacttimerwarn = 30seconds            ; Message to play when the link activity timer has 30 seconds left.

 

;remote_inact_timeout =                 ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60)

;remote_timeout =                       ; Session time out for remote base. Set to 0 to disable. (60 * 60)

;remote_timeout_warning_freq =          ; 30

;remote_timeout_warning =               ; (3 * 60)

 

;nounkeyct = 0                          ; Set to a 1 to eliminate courtesy tones and associated delays.

 

holdofftelem = 0                        ; Hold off all telemetry when signal is present on receiver or from connected nodes

                                        ; except when an ID needs to be done and there is a signal coming from a connected node.

 

telemdefault = 0                        ; 0 = telemetry output off

                                        ; 1 = telemetry output on (default = 1)

                                        ; 2 = timed telemetry output on command execution and for a short time thereafter.

 

telemdynamic = 1                        ; 0 = disallow users to change the local telemetry setting with a COP command,

                                        ; 1 = Allow users to change the setting with a COP command. (default = 1)

 

;beaconing = 0                          ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)

 

parrotmode = 0                          ; 0 = Parrot Off (default = 0)

                                        ; 1 = Parrot On Command

                                        ; 2 = Parrot Always

                                        ; 3 = Parrot Once by Command

 

parrottime = 1000                       ; Set the amount of time in milliseconds

                                        ; to wait before parroting what was received

 

;rxnotch=1065,40                        ; (Optional) Notch a particular frequency for a specified

                                        ; b/w. app_rpt must have been compiled with

                                        ; the notch option

 

startup_macro =

 

; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign   ; Point to alternate nodename sound directory

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Need more information on these

 

;extnodes = extnodes-different  ; section in extnodefile containing dynamic node information (optional)

;extnodefile = /foo/nodes       ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional)

;extnodefile2 =                 ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes????

;nodenames = /foo/names         ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames

;archivedir = /tmp              ; defines and enables activity recording into specified directory (optional)

;monminblocks = 2048            ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)

 

;                               ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set

;                               ; to support tail messages. They can be omitted otherwise.

;tailmessagetime = 300000       ; Play a tail message every 5 mins

;tailsquashedtime = 30000       ; If squashed by another user,

;                               ; try again after 30 seconds

;tailmessagelist = msg1,msg2    ; list of messages to be played for tail message

 

; alt_functions

; ctgroup

; dphone_functions

; idtime

; iobase

; iospeed

; locallist

; mars          Remote Base

; memory

; nobusyout

; nodes

; nolocallinkct

; notelemtx

; outxlat

; parrot

; propagate_phonedtmf

; rptnode

; rptinactmacro  Macro to execute when inactivity timer expires

; rptinacttime   Inactivity timer time in seconds  (0 seconds disables feature)

; rxnotch       Optional Audio notch

; simplexphonedelay

; tonemacro

; tonezone

; txlimits

 

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

 

; *** Status Reporting ***

 

; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org

statpost_url = http://stats.allstarlink.org/uhandler ; Status updates

 

[functions]

 

; Prefix        Functions

; *1            Disconnect Link

; *2            Monitor Link

; *3            Connect Link

; *4            Command Mode

; *5            Macros

; *6            User Functions

; *7            Connection Status/Functions

; *8            User Functions

; *9            User Functions

; *0            User Functions

 

; *A            User Functions

; *B            User Functions

; *C            User Functions

; *D            User Functions

 

 

; Mandatory Command Codes

; http://docs.allstarlink.org/drupal/node/91

 

1 = ilink,1             ; Disconnect specified link

2 = ilink,2             ; Connect specified link -- monitor only

3 = ilink,3             ; Connect specified link -- tranceive

4 = ilink,4             ; Enter command mode on specified link

70 = ilink,5            ; System status

99 = cop,6              ; PTT (phone mode only)

 

; End Mandatory Command Codes

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Macro Commands

5 = macro

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Autopatch Commands

; Note, This may be a good place for other 2 digit frequently used commands

 

61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000  ; Autopatch up

62 = autopatchdn                                                 ; Autopatch down

 

; autopatchup can optionally take comma delimited setting=value pairs:

 

; context = string              ; Override default context with "string"

; dialtime = ms                 ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second)

; farenddisconnect = 1          ; Automatically disconnect when called party hangs up

; noct = 1                      ; Don't send repeater courtesy tone during autopatch calls

; quiet = 1                     ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up

                                ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Status Commands

 

; 1 - Force ID (global)

; 2 - Give Time of Day (global)

; 3 - Give software Version (global)

; 4 - Give GPS location info

; 5 - Last (dtmf) user

; 11 - Force ID (local only)

; 12 - Give Time of Day (local only)

 

721 = status,1          ; Force ID (global)

722 = status,2          ; Give Time of Day (global)

723 = status,3          ; Give software Version (global)

724 = status,4          ; Give GPS location info

725 = status,5          ; Last (dtmf) user

711 = status,11         ; Force ID (local only)

712 = status,12         ; Give Time of Day (local only)

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Link Commands

 

; 1 - Disconnect specified link

; 2 - Connect specified link -- monitor only

; 3 - Connect specified link -- tranceive

; 4 - Enter command mode on specified link

; 5 - System status

; 6 - Disconnect all links

; 7 - Last Node to Key Up

; 8 - Connect specified link -- local monitor only

; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.

; 10 - Disconnect all RANGER links (except permalinks)

; 11 - Disconnect a previously permanently connected link

; 12 - Permanently connect specified link -- monitor only

; 13 - Permanently connect specified link -- tranceive

; 15 - Full system status (all nodes)

; 16 - Reconnect links disconnected with "disconnect all links"

; 17 - MDC test (for diag purposes)

; 18 - Permanently Connect specified link -- local monitor only

 

; ilink commands 1 through 5 are defined in the Mandatory Command section

 

806 = ilink,6                   ; Disconnect all links

807 = ilink,7                   ; Last Node to Key Up

808 = ilink,8                   ; Connect specified link -- local monitor only

809 = ilink,9,1999,"Testing"    ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes

810 = ilink,10                  ; Disconnect all RANGER links (except permalinks)

811 = ilink,11                  ; Disconnect a previously permanently connected link

812 = ilink,12                  ; Permanently connect specified link -- monitor only

813 = ilink,13                  ; Permanently connect specified link -- tranceive

815 = ilink,15                  ; Full system status (all nodes)

816 = ilink,16                  ; Reconnect links disconnected with "disconnect all links"

817 = ilink,17                  ; MDC test (for diag purposes)

818 = ilink 18                  ; Permanently Connect specified link -- local monitor only

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Control operator (cop) functions. Change these to something other than these codes listed below!

 

901 = cop,1                   ��         ; System warm boot

902 = cop,2                             ; System enable

903 = cop,3                             ; System disable

 

904 = cop,4                             ; Test tone on/off (toggle)

905 = cop,5                             ; Dump system variables on console (debug use only)

 

907 = cop,7                             ; Time out timer enable

908 = cop,8                             ; Time out timer disable

 

909 = cop,9                             ; Autopatch enable

910 = cop,10                            ; Autopatch disable

 

911 = cop,11                            ; User linking functions enable

912 = cop,12                            ; User linking functions disable

 

913 = cop,13                            ; Query system control state

914 = cop,14                            ; Set system control state

 

915 = cop,15                            ; Scheduler enable

916 = cop,16                            ; Scheduler disable

 

917 = cop,17                            ; User functions enable (time, id, etc)

918 = cop,18                            ; User functions disable

 

919 = cop,19                            ; Select alternate hang time (althangtime)

920 = cop,20                            ; Select standard hangtime (hangtime)

 

921 = cop,21                            ; Enable Parrot Mode

922 = cop,22                            ; Disable Parrot Mode

923 = cop,23                            ; Birdbath (Current Parrot Cleanup/Flush)

 

924 = cop,24                            ; Flush all telemetry

925 = cop,25                            ; Query last node un-keyed

926 = cop,26                            ; Query all nodes keyed/unkeyed

927 = cop,27                            ; Reset DAQ minimum on a pin

928 = cop,28                            ; Reset DAQ maximum on a pin

 

930 = cop,30                            ; Recall Memory Setting in Attached Xcvr

 

931 = cop,31                            ; Channel Selector for Parallel Programmed Xcvr

 

932 = cop,32                            ; Touchtone pad test: command + Digit string + # to playback all digits pressed

 

933 = cop,33                            ; Local Telemetry Output Enable

934 = cop,34                            ; Local Telemetry Output Disable

935 = cop,35                            ; Local Telemetry Output on Demand

 

936 = cop,36                            ; Foreign Link Local Output Path Enable

937 = cop,37                            ; Foreign Link Local Output Path Disable

938 = cop,38                            ; Foreign Link Local Output Path Follows Local Telemetry

939 = cop,39                            ; Foreign Link Local Output Path on Demand

 

942 = cop,42                            ; Echolink announce node # only

943 = cop,43                            ; Echolink announce node Callsign only

944 = cop,44                            ; Echolink announce node # & Callsign

 

945 = cop,45                            ; Link Activity timer enable

945 = cop,46                            ; Link Activity timer disable

947 = cop,47                            ; Reset "Link Config Changed" Flag

 

948 = cop,48                            ; Send Page Tone (Tone specs separated by parenthesis)

 

949 = cop,49                            ; Disable incoming connections (control state noice)

950 = cop,50                            ; Enable incoming connections (control state noicd)

 

951 = cop,51                            ; Enable sleep mode

952 = cop,52                            ; Disable sleep mode

953 = cop,53                            ; Wake up from sleep

954 = cop,54                            ; Go to sleep

955 = cop,55                            ; Parrot Once if parrot mode is disabled

 

956 = cop,56                            ; Rx CTCSS Enable

957 = cop,57                            ; Rx CTCSS Disable

 

958 = cop.58                            ; Tx CTCSS On Input only Enable

959 = cop,59                            ; Tx CTCSS On Input only Disable

 

960 = cop,60                            ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])

                                        ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call

                                        ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.

                                        ; DestID and subcode are only specified for  the 'C' type message.

                                        ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of

                                        ; the radio being called, and the subcodes are as follows:

                                        ; Subcode '8205' is Voice Selective Call for Spectra ('Call')

                                        ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or

                                        ; Astro-Saber('Call')

                                        ; Subcode '810D' is Call Alert (like Maxtrac 'CA')

 

961 = cop,61                            ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)

962 = cop,62                            ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)

 

963 = cop,63                            ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])

964 = cop,64                            ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])

965 = cop,65                            ; Send POCSAG page (equipped channel types only)

 

[functions-remote]

 

0 = remote,1                            ; Retrieve Memory

1 = remote,2                            ; Set freq.

2 = remote,3                            ; Set tx PL tone

3 = remote,4                            ; Set rx PL tone

40 = remote,100                         ; Rx PL off

41 = remote,101                         ; Rx PL on

42 = remote,102                         ; Tx PL off

43 = remote,103                         ; Tx PL on

44 = remote,104                         ; Low Power

45 = remote,105                         ; Medium Power

46 = remote,106                         ; High Power

711 = remote,107                        ; Bump -20

714 = remote,108                        ; Bump -100

717 = remote,109                        ; Bump -500

713 = remote,110                        ; Bump +20

716 = remote,111                        ; Bump +100

719 = remote,112                        ; Bump +500

721 = remote,113                        ; Scan - slow

724 = remote,114                        ; Scan - quick

727 = remote,115                        ; Scan - fast

723 = remote,116                        ; Scan + slow

726 = remote,117                        ; Scan + quick

729 = remote,118                        ; Scan + fast

79 = remote,119                         ; Tune

51 = remote,5                           ; Long status query

52 = remote,140                         ; Short status query

67 = remote,210                         ; Send a *

69 = remote,211                         ; Send a #

;91 = remote,99,CALLSIGN,LICENSETAG     ; Remote base login.

                                        ; Define a different dtmf sequence for each user which is

                                        ; authorized to use the remote base to control access to it.

                                        ; For examble 9139583=remote,99,WB6NIL,G would grant access to

                                        ; the remote base and announce WB6NIL as being logged in.

                                        ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to

                                        ; the remote base and announce WA6ZFT as being logged in.

                                        ; When the remote base is disconnected from the originating node, the

                                        ; user will be logged out. The LICENSETAG argument is used to enforce

                                        ; tx frequency limits. See [txlimits] below.

85 = cop,6                              ; Remote base telephone key

 

 

[telemetry]

 

; Telemetry entries can be shared across all repeaters, or defined for each repeater.

; Can be a tone sequence, morse string, or a file

;

; |t - Tone escape sequence

;

; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)

; Single frequencies are created by setting freq1 or freq2 to zero.

;

; |m - Morse escape sequence

;

; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the

; [morse] section.

;

; Follow with an alphanumeric string

;

; |i - Morse ID escape sequence

;

; Sends Morse code at the ID amplitude and ID frequency as defined in the

; [morse] section.

;

; path/to/sound/file/without/extension

;

; Send the sound if in place of a constructed tone. Do not include the file extension

; Example: ct8 = rpt/bloop

; Example: idrecording = rpt/nodenames/1999

 

ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)

ct2 = |t(660,880,150,2048)

ct3 = |t(440,0,150,4096)

ct4 = |t(550,0,150,2048)

ct5 = |t(660,0,150,2048)

ct6 = |t(880,0,150,2048)

ct7 = |t(660,440,150,2048)

ct8 = |t(700,1100,150,2048)

ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)

remotemon = |t(1209,0,50,2048)                                  ; local courtesy tone when receive only

remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000)         ; local courtesy tone when linked Trancieve mode

cmdmode = |t(900,903,200,2048)

functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)

remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)

pfxtone = |t(350,440,30000,3072)

patchup = rpt/callproceeding

patchdown = rpt/callterminated

 

; As far as what the numbers mean,

; (000,000,010,000)

;   |   |   |   |-------amplitude

;   |   |   |-------------duration

;   |   |-------------------Tone 2

;   |-------------------------Tone 1

 

; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.

; Use it for a delay.  Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter)

; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.

 

; Morse code parameters, these are common to all repeaters.

 

[morse]

speed = 20                              ; Approximate speed in WPM

frequency = 800                         ; Morse Telemetry Frequency

amplitude = 4096                        ; Morse Telemetry Amplitude

idfrequency = 1065                      ; Morse ID Frequency

idamplitude = 1024                      ; Morse ID Amplitude

 

;

; This section allows wait times for telemetry events to be adjusted

; A section for wait times can be defined for every repeater

;

 

[wait-times]

telemwait = 2000                        ; Time to wait before sending most telemetry

idwait = 500                            ; Time to wait before starting ID

unkeywait = 2000                        ; Time to wait after unkey before sending CT's and link telemetry

calltermwait = 2000                     ; Time to wait before announcing "call terminated"

 

;

; This is where you define your nodes which cam be connected to.

;

 

[nodes]

; Note, if you are using automatic update for allstar link nodes,

; no allstar link nodes should be defined here. Only place a definition

; for your local nodes, and private (off of allstar link) nodes here.

 

460310 = radio@....0.1:4569/460310,NONE       ; This must be changed to your node number

                                        ; and iax port number if not the default

; Memories for remote bases

 

[memory]

;00 = 146.580,100.0,m

;01 = 147.030,103.5,m+t

;02 = 147.240,103.5,m+t

;03 = 147.765,79.7,m-t

;04 = 146.460,100.0,m

;05 = 146.550,100.0,m

 

; Place command macros here

 

[macro]

;1 = *32011#

;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#

;3 = *32001*32011*32050*32030*32060#

 

 

; Data Acquisition configuration

 

;[daq-list]

;device = device_name1

;device = device_name2

 

;Where: device_name1 and device_name2 are stanzas you define in this file

 

;device = daq-cham-1

 

; Device name

 

;[daq-cham-1]                           ; Defined in [daq-list]

;hwtype = uchameleon                    ; DAQ hardware type

;devnode = /dev/ttyUSB0                 ; DAQ device node (if required)

;1 = inadc                              ; Pin definition for an ADC channel

;2 = inadc

;3 = inadc

;4 = inadc

;5 = inadc

;6 = inadc

;7 = inadc

;8 = inadc

;9 = inp                                ; Pin definition for an input with a weak pullup resistor

;10 = inp

;11 = inp

;12 = inp

;13 = in                                ; Pin definition for an input without a weak pullup resistor

;14 = out                               ; Pin definition for an output

;15 = out

;16 = out

;17 = out

;18 = out

 

;[meter-faces]

 

;face = scale(scalepre,scalediv,scalepost),word/?,...

;

; scalepre = offset to add before dividing with scalediv

; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts).

; scalepost = offset to add after dividing with scalediv

;

;face = range(X-Y:word,X2-Y2:word,...),word/?,...

;face = bit(low-word,high-word),word/?,...

;

; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories,

; or a question mark which is  a placeholder for the measured value.

;

;

; Battery voltage 0-20 volts

;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts

; 4 quadrant wind direction

;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?

; LM34 temperature sensor with 130 deg. F full scale

;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit

; Status poll (non alarmed)

;light = bit(ha/off,ha/on),ha/light,?

 

;[alarms]

;

;tag = device,pin,node,ignorefirst,func-low,func-hi

;

;tag = a unique name for the alarm

;device = daq device to poll

;pin = the device pin to be monitored

;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it

;node = the node number to execute the function on

;func-low = the DTMF function to execute on a high to low transition

;func-high = the DTMF function to execute on a low to high transition

;

; a  '-' as a function name is shorthand for no-operation

;

;door = daq-cham-1,9,1,2017,*7,-

;pwrfail = daq-cham-1,10,0,2017,*911111,-

;

; Control states

; Allow several control operator functions to be changed at once using one command (good for scheduling)

;

;[controlstates]

;statenum = copcmd,[copcmd]...

;0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation

;1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation

;2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation

 

; Scheduler - execute a macro at a given time

 

[schedule]

;dtmf_function =  m h dom mon dow  ; ala cron, star is implied

;2 = 00 00 * * *   ; at midnight, execute macro 2.

 

#includeifexists custom/rpt.conf

 

 

 

 

Analog_Bridge.ini

 

 

; Analog_Bridge configuration file.

;   This file should be placed in either /etc or it can be

;   supplied as a path on the Analog_Bridge command line.

 

; The best way to think of this file is that there are two main sections, the USRP (analog audio) and

; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and

; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.

; As you might expect, the reverse direction is defined too.

 

; Analog_Bridge supports include files. More on this later...

include = dvsm.macro

; include = asl.macro

 

; General Section describes settings for Analog_Bridge itself.

[GENERAL]

logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal

 

; Metadata management

exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)

transferRootDir = /tmp                  ; Export database files to USRP partner

subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data

 

; General vocoder setup information

decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found

useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)

emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server

 

pcmPort = 2222                          ; UDP port to send to the WebProxy

 

; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)

[AMBE_AUDIO]

address = 127.0.0.1                     ; IP address of xx_Bridge

txPort = 31103                          ; Transmit TLV frames to partner on this port

rxPort = 31100                          ; Listen for TLV frames from partner on this port

ambeMode = DMR                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)

minTxTimeMS = 2500                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)

 

; The metadata below is used when ASL is the source since it does not have any concept of digital modes

gatewayDmrId = 1112721                  ; ID to use when transmitting from Analog_Bridge 7 digit ID

repeaterID = 111272123                  ; ID of source repeater 7 digit ID plus 2 digit SSID

txTg = 31676                               ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge

txTs = 2                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge

colorCode = 1                           ; Color Code to assign DMR frames

 

; Information for USRP channel driver.  This interface uses PCM to transfer audio information

; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected

; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself,

; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.

;   When using ASL, this matches the rpt.conf ASL file with a setting like:

;   rxchannel = usrp/127.0.0.1:34001:32001

;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch

;   each instance with its own ini file.

[USRP]

address = 127.0.0.1                     ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge)

txPort = 32001                          ; Transmit USRP frames on this port

rxPort = 34001                          ; Listen for USRP frames on this port

usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)

usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)

tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)

tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

 

[MACROS]

 

; Where the macros are

; xxxx=yyyy

; xxxx is the dial string to match

; yyyy is the command line to execute

 

; xxxx must be preceded by a *

; xxxx can be any string (alphanumeric)

; yyyy is the command to execute

; yyyy will replace xxxx in the dial string

; arguments follow the macro name with a # delimiter

 

; For example using macro "5678" above would look like:

; *5678#9876

 

; Which would invoke:

; echo 9876

 

; Information for DV3000 hardware decoder

;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)

;   Use top server and port if using AMBEServer

;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)

;   Did you run AMBETest4.py before using this?

[DV3000]

address = 127.0.0.1                   ; IP address of AMBEServer

rxPort = 2460                         ; Port of AMBEServer

; address = /dev/ttyUSB0              ; Device of DV3000U on this machine

; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)

; serial = true                       ; Use serial=true f

 

 

 

 

 



Steve Siesel [K4KSA]
 

After restarting AB and Asterisk….also md3890-emu is running

Still no Joy…Here is the latest start of Analog_bridge.log

 

 

I: 2021-02-14 19:43:13.761 Analog_Bridge is starting

M: 2021-02-14 19:43:13.762 Setting [MACROS] DMR -> /opt/MMDVM_Bridge/dvswitch.sh mode DMR

M: 2021-02-14 19:43:13.762 Setting [MACROS] DSTAR -> /opt/MMDVM_Bridge/dvswitch.sh mode DSTAR

M: 2021-02-14 19:43:13.762 Setting [MACROS] NXDN -> /opt/MMDVM_Bridge/dvswitch.sh mode NXDN

M: 2021-02-14 19:43:13.762 Setting [MACROS] P25 -> /opt/MMDVM_Bridge/dvswitch.sh mode P25

M: 2021-02-14 19:43:13.762 Setting [MACROS] YSF -> /opt/MMDVM_Bridge/dvswitch.sh mode YSF

M: 2021-02-14 19:43:13.762 Setting [MACROS] dbupdate -> /opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles

M: 2021-02-14 19:43:13.764 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh

M: 2021-02-14 19:43:13.765 Setting [] include -> dvsm.macro

M: 2021-02-14 19:43:13.766 Setting [GENERAL] logLevel -> 2

M: 2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata -> true

M: 2021-02-14 19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp

M: 2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv

M: 2021-02-14 19:43:13.768 Setting [GENERAL] decoderFallBack -> true

M: 2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator -> false

M: 2021-02-14 19:43:13.769 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470

M: 2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort -> 2222

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1

M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR

M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721

M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2

M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1

M: 2021-02-14 19:43:13.773 Setting [USRP] address -> 127.0.0.1

M: 2021-02-14 19:43:13.773 Setting [USRP] txPort -> 32001

M: 2021-02-14 19:43:13.773 Setting [USRP] rxPort -> 34001

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpGain -> 1.10

M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY

M: 2021-02-14 19:43:13.775 Setting [USRP] tlvGain -> 0.35

M: 2021-02-14 19:43:13.776 Setting [DV3000] address -> 127.0.0.1

M: 2021-02-14 19:43:13.776 Setting [DV3000] rxPort -> 2460

I: 2021-02-14 19:43:13.777 Open UDP listener on 127.0.0.1:31100

I: 2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001

M: 2021-02-14 19:43:13.777 Connecting to DV3000 hardware......

W: 2021-02-14 19:43:13.871 DV3000 did not reset at 127.0.0.1:2460

W: 2021-02-14 19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset failed)

I: 2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850

I: 2021-02-14 19:43:16.073 Default extended metadata <K4KSA>

W: 2021-02-14 19:43:16.073 Using software MBE decoder version 1.2.3

W: 2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE vocoder

I: 2021-02-14 19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s) 32001

I: 2021-02-14 19:43:16.074 Sending PCM to  clients at 127.0.0.1 on port 2222

I: 2021-02-14 19:43:16.074 Starting TLV --> Analog_Bridge (decoder) --> USRP thread

I: 2021-02-14 19:43:16.075 Starting USRP --> Analog_Bridge (encoder) -> TLV thread

 

 

From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS
Sent: Sunday, February 14, 2021 2:41 PM
To: main@DVSwitch.groups.io
Subject: Re: [DVSwitch] ASL<>AB

 

You have 2 channel drivers uncommented:

rxchannel = dahdi/pseudo                ; No radio (hub) <--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB
; rxchannel = Pi/1                      ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999            ; USBRadio (DSP)
; rxchannel = Dahdi/1                   ; PCI Quad card
; rxchannel = Beagle/1                  ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999                ; RTCM device

On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote:

Can you look at this as well…..

 

I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that.

 

Steve

 

 

; Your Repeater

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

[460310]                                        ; Change this to your assigned node number

 

                                        ; Must also be enabled in modules.conf

                                        ; Rx audio/signalling channel. Choose ONLY 1 per node stanza

 

                                        ; Enable the selected channel driver in modules.conf !!!

rxchannel = dahdi/pseudo                ; No radio (hub)

; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB

; rxchannel = Pi/1                      ; Raspberry Pi PiTA

; rxchannel = Radio/usb_1999            ; USBRadio (DSP)

; rxchannel = Dahdi/1                   ; PCI Quad card

; rxchannel = Beagle/1                  ; BeagleBoard

rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP

; rxchannel = Voter/1999                ; RTCM device

 

 

duplex = 1                              ; 0 = Half duplex with no telemetry tones or hang time.

                                        ;     Special Case: Full duplex if linktolink is set to yes.

                                        ;     This mode is preferred when interfacing with an external multiport repeater controller.

                                        ;     Comment out idrecording and idtalkover to suppress IDs also

                                        ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio.

                                        ;     This mode is preferred when interfacing a simplex node.

                                        ; 2 = Full Duplex with telemetry tones and hang time.

                                        ;     This mode is preferred when interfacing a repeater.

                                        ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio.

                                        ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.

 

linktolink = no                         ; disables forcing physical half-duplex operation of main repeater while

                                        ; still keeping half-duplex semantics (optional)

 

linkmongain = 0                         ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received.

                                        ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db.

                                        ; If linkmongain set to a positive number monitored audio will increase by the set amount in db.

                                        ; The value of linkmongain is in db. The default value is 0 db.

 

erxgain = -3                            ; Echolink receive gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

etxgain = 3                             ; Echolink transmit gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

;eannmode = 1                           ; 1 = Say only node number on echolink connects (default = 1)

                                        ; 2 = say phonetic call sign only on echolink connects

                                        ; 3 = say phonetic call sign and node number on echolink connects

 

;controlstates = controlstates          ; system control state stanza

 

scheduler = schedule                    ; scheduler stanza

functions = functions                   ; Repeater Function stanza

phone_functions = functions             ; Phone Function stanza

link_functions = functions              ; Link Function stanza

 

telemetry = telemetry                   ; Telemetry stanza

morse = morse                           ; Morse stanza

wait_times = wait-times                 ; Wait times stanza

 

context = radio                         ; dialing context for phone

callerid = "Repeater" <0000000000>      ; callerid for phone calls

accountcode = RADIO                     ; account code (optional)

 

hangtime = 5000                         ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms)

althangtime = 4000                      ; longer squelch tail

totime = 180000                         ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

 

idrecording = |iWA4XYZ                  ; cording or morse string see http://ohnosec.org/drupal/node/87

idtalkover = |iWA4XYZ                   ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129

                                        ; See Telemetry section Example: idrecording = rpt/nodenames/1999

idtime = 540000                         ; id interval time (in ms) (optional) Default 5 minutes (300000 ms)

politeid = 30000                        ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)

 

unlinkedct = ct2                        ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none)

remotect = ct3                          ; remote linked courtesy tone (indicates a remote is in the list of links)

linkunkeyct = ct8                       ; sent when a transmission received over the link unkeys

;nolocallinkct = 0                      ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).

 

;connpgm = yourconnectprogram           ; Disabled. Execute a program you specify on connect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being connected to us (them)

;discpgm = yourdisconnectprogram        ; Disabled. Execute a program you specify on disconnect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being disconnected from us (them)

 

;lnkactenable = 0                       ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.

 

;lnkacttime = 1800                      ; Link activity timer time in seconds.

;lnkactmacro = *52                      ; Function to execute when link activity timer expires.

;lnkacttimerwarn = 30seconds            ; Message to play when the link activity timer has 30 seconds left.

 

;remote_inact_timeout =                 ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60)

;remote_timeout =                       ; Session time out for remote base. Set to 0 to disable. (60 * 60)

;remote_timeout_warning_freq =          ; 30

;remote_timeout_warning =               ; (3 * 60)

 

;nounkeyct = 0                          ; Set to a 1 to eliminate courtesy tones and associated delays.

 

holdofftelem = 0                        ; Hold off all telemetry when signal is present on receiver or from connected nodes

                                        ; except when an ID needs to be done and there is a signal coming from a connected node.

 

telemdefault = 0                        ; 0 = telemetry output off

                                        ; 1 = telemetry output on (default = 1)

                                        ; 2 = timed telemetry output on command execution and for a short time thereafter.

 

telemdynamic = 1                        ; 0 = disallow users to change the local telemetry setting with a COP command,

                                        ; 1 = Allow users to change the setting with a COP command. (default = 1)

 

;beaconing = 0                          ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)

 

parrotmode = 0                          ; 0 = Parrot Off (default = 0)

                                        ; 1 = Parrot On Command

                                        ; 2 = Parrot Always

                                        ; 3 = Parrot Once by Command

 

parrottime = 1000                       ; Set the amount of time in milliseconds

                                        ; to wait before parroting what was received

 

;rxnotch=1065,40                        ; (Optional) Notch a particular frequency for a specified

                                        ; b/w. app_rpt must have been compiled with

                                        ; the notch option

 

startup_macro =

 

; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign   ; Point to alternate nodename sound directory

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Need more information on these

 

;extnodes = extnodes-different  ; section in extnodefile containing dynamic node information (optional)

;extnodefile = /foo/nodes       ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional)

;extnodefile2 =                 ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes????

;nodenames = /foo/names         ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames

;archivedir = /tmp              ; defines and enables activity recording into specified directory (optional)

;monminblocks = 2048            ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)

 

;                               ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set

;                               ; to support tail messages. They can be omitted otherwise.

;tailmessagetime = 300000       ; Play a tail message every 5 mins

;tailsquashedtime = 30000       ; If squashed by another user,

;                               ; try again after 30 seconds

;tailmessagelist = msg1,msg2    ; list of messages to be played for tail message

 

; alt_functions

; ctgroup

; dphone_functions

; idtime

; iobase

; iospeed

; locallist

; mars          Remote Base

; memory

; nobusyout

; nodes

; nolocallinkct

; notelemtx

; outxlat

; parrot

; propagate_phonedtmf

; rptnode

; rptinactmacro  Macro to execute when inactivity timer expires

; rptinacttime   Inactivity timer time in seconds  (0 seconds disables feature)

; rxnotch       Optional Audio notch

; simplexphonedelay

; tonemacro

; tonezone

; txlimits

 

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

 

; *** Status Reporting ***

 

; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org

statpost_url = http://stats.allstarlink.org/uhandler ; Status updates

 

[functions]

 

; Prefix        Functions

; *1            Disconnect Link

; *2            Monitor Link

; *3            Connect Link

; *4            Command Mode

; *5            Macros

; *6            User Functions

; *7            Connection Status/Functions

; *8            User Functions

; *9            User Functions

; *0            User Functions

 

; *A            User Functions

; *B            User Functions

; *C            User Functions

; *D            User Functions

 

 

; Mandatory Command Codes

; http://docs.allstarlink.org/drupal/node/91

 

1 = ilink,1             ; Disconnect specified link

2 = ilink,2             ; Connect specified link -- monitor only

3 = ilink,3             ; Connect specified link -- tranceive

4 = ilink,4             ; Enter command mode on specified link

70 = ilink,5            ; System status

99 = cop,6              ; PTT (phone mode only)

 

; End Mandatory Command Codes

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Macro Commands

5 = macro

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Autopatch Commands

; Note, This may be a good place for other 2 digit frequently used commands

 

61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000  ; Autopatch up

62 = autopatchdn                                                 ; Autopatch down

 

; autopatchup can optionally take comma delimited setting=value pairs:

 

; context = string              ; Override default context with "string"

; dialtime = ms                 ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second)

; farenddisconnect = 1          ; Automatically disconnect when called party hangs up

; noct = 1                      ; Don't send repeater courtesy tone during autopatch calls

; quiet = 1                     ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up

                                ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Status Commands

 

; 1 - Force ID (global)

; 2 - Give Time of Day (global)

; 3 - Give software Version (global)

; 4 - Give GPS location info

; 5 - Last (dtmf) user

; 11 - Force ID (local only)

; 12 - Give Time of Day (local only)

 

721 = status,1          ; Force ID (global)

722 = status,2          ; Give Time of Day (global)

723 = status,3          ; Give software Version (global)

724 = status,4          ; Give GPS location info

725 = status,5          ; Last (dtmf) user

711 = status,11         ; Force ID (local only)

712 = status,12         ; Give Time of Day (local only)

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Link Commands

 

; 1 - Disconnect specified link

; 2 - Connect specified link -- monitor only

; 3 - Connect specified link -- tranceive

; 4 - Enter command mode on specified link

; 5 - System status

; 6 - Disconnect all links

; 7 - Last Node to Key Up

; 8 - Connect specified link -- local monitor only

; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.

; 10 - Disconnect all RANGER links (except permalinks)

; 11 - Disconnect a previously permanently connected link

; 12 - Permanently connect specified link -- monitor only

; 13 - Permanently connect specified link -- tranceive

; 15 - Full system status (all nodes)

; 16 - Reconnect links disconnected with "disconnect all links"

; 17 - MDC test (for diag purposes)

; 18 - Permanently Connect specified link -- local monitor only

 

; ilink commands 1 through 5 are defined in the Mandatory Command section

 

806 = ilink,6                   ; Disconnect all links

807 = ilink,7                   ; Last Node to Key Up

808 = ilink,8                   ; Connect specified link -- local monitor only

809 = ilink,9,1999,"Testing"    ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes

810 = ilink,10                  ; Disconnect all RANGER links (except permalinks)

811 = ilink,11                  ; Disconnect a previously permanently connected link

812 = ilink,12                  ; Permanently connect specified link -- monitor only

813 = ilink,13                  ; Permanently connect specified link -- tranceive

815 = ilink,15                  ; Full system status (all nodes)

816 = ilink,16                  ; Reconnect links disconnected with "disconnect all links"

817 = ilink,17                  ; MDC test (for diag purposes)

818 = ilink 18                  ; Permanently Connect specified link -- local monitor only

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Control operator (cop) functions. Change these to something other than these codes listed below!

 

901 = cop,1                             ; System warm boot

902 = cop,2                             ; System enable

903 = cop,3                             ; System disable

 

904 = cop,4                             ; Test tone on/off (toggle)

905 = cop,5                             ; Dump system variables on console (debug use only)

 

907 = cop,7                             ; Time out timer enable

908 = cop,8                             ; Time out timer disable

 

909 = cop,9                             ; Autopatch enable

910 = cop,10                            ; Autopatch disable

 

911 = cop,11                            ; User linking functions enable

912 = cop,12                            ; User linking functions disable

 

913 = cop,13                            ; Query system control state

914 = cop,14                            ; Set system control state

 

915 = cop,15                            ; Scheduler enable

916 = cop,16                            ; Scheduler disable

 

917 = cop,17                            ; User functions enable (time, id, etc)

918 = cop,18                            ; User functions disable

 

919 = cop,19                            ; Select alternate hang time (althangtime)

920 = cop,20                            ; Select standard hangtime (hangtime)

 

921 = cop,21                            ; Enable Parrot Mode

922 = cop,22                            ; Disable Parrot Mode

923 = cop,23                            ; Birdbath (Current Parrot Cleanup/Flush)

 

924 = cop,24                            ; Flush all telemetry

925 = cop,25                            ; Query last node un-keyed

926 = cop,26                            ; Query all nodes keyed/unkeyed

927 = cop,27                            ; Reset DAQ minimum on a pin

928 = cop,28                            ; Reset DAQ maximum on a pin

 

930 = cop,30                            ; Recall Memory Setting in Attached Xcvr

 

931 = cop,31                            ; Channel Selector for Parallel Programmed Xcvr

 

932 = cop,32                            ; Touchtone pad test: command + Digit string + # to playback all digits pressed

 

933 = cop,33                            ; Local Telemetry Output Enable

934 = cop,34                            ; Local Telemetry Output Disable

935 = cop,35                            ; Local Telemetry Output on Demand

 

936 = cop,36                            ; Foreign Link Local Output Path Enable

937 = cop,37                            ; Foreign Link Local Output Path Disable

938 = cop,38                            ; Foreign Link Local Output Path Follows Local Telemetry

939 = cop,39                            ; Foreign Link Local Output Path on Demand

 

942 = cop,42                            ; Echolink announce node # only

943 = cop,43                            ; Echolink announce node Callsign only

944 = cop,44                            ; Echolink announce node # & Callsign

 

945 = cop,45                            ; Link Activity timer enable

945 = cop,46                            ; Link Activity timer disable

947 = cop,47                            ; Reset "Link Config Changed" Flag

 

948 = cop,48                            ; Send Page Tone (Tone specs separated by parenthesis)

 

949 = cop,49                            ; Disable incoming connections (control state noice)

950 = cop,50                            ; Enable incoming connections (control state noicd)

 

951 = cop,51                            ; Enable sleep mode

952 = cop,52                            ; Disable sleep mode

953 = cop,53                            ; Wake up from sleep

954 = cop,54                            ; Go to sleep

955 = cop,55                            ; Parrot Once if parrot mode is disabled

 

956 = cop,56                            ; Rx CTCSS Enable

957 = cop,57                            ; Rx CTCSS Disable

 

958 = cop.58                            ; Tx CTCSS On Input only Enable

959 = cop,59                            ; Tx CTCSS On Input only Disable

 

960 = cop,60                            ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])

                                        ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call

                                        ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.

                                        ; DestID and subcode are only specified for  the 'C' type message.

                                        ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of

                                        ; the radio being called, and the subcodes are as follows:

                                        ; Subcode '8205' is Voice Selective Call for Spectra ('Call')

                                        ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or

                                        ; Astro-Saber('Call')

                                        ; Subcode '810D' is Call Alert (like Maxtrac 'CA')

 

961 = cop,61                            ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)

962 = cop,62                            ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)

 

963 = cop,63                            ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])

964 = cop,64                            ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])

965 = cop,65                            ; Send POCSAG page (equipped channel types only)

 

[functions-remote]

 

0 = remote,1                            ; Retrieve Memory

1 = remote,2                            ; Set freq.

2 = remote,3                            ; Set tx PL tone

3 = remote,4                            ; Set rx PL tone

40 = remote,100                         ; Rx PL off

41 = remote,101                         ; Rx PL on

42 = remote,102                         ; Tx PL off

43 = remote,103                         ; Tx PL on

44 = remote,104                         ; Low Power

45 = remote,105                         ; Medium Power

46 = remote,106                         ; High Power

711 = remote,107                        ; Bump -20

714 = remote,108                        ; Bump -100

717 = remote,109                        ; Bump -500

713 = remote,110                        ; Bump +20

716 = remote,111                        ; Bump +100

719 = remote,112                        ; Bump +500

721 = remote,113                        ; Scan - slow

724 = remote,114                        ; Scan - quick

727 = remote,115                        ; Scan - fast

723 = remote,116                        ; Scan + slow

726 = remote,117                        ; Scan + quick

729 = remote,118                        ; Scan + fast

79 = remote,119                         ; Tune

51 = remote,5                           ; Long status query

52 = remote,140                         ; Short status query

67 = remote,210                         ; Send a *

69 = remote,211                         ; Send a #

;91 = remote,99,CALLSIGN,LICENSETAG     ; Remote base login.

                                        ; Define a different dtmf sequence for each user which is

                                        ; authorized to use the remote base to control access to it.

                                        ; For examble 9139583=remote,99,WB6NIL,G would grant access to

                                        ; the remote base and announce WB6NIL as being logged in.

                                        ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to

                                        ; the remote base and announce WA6ZFT as being logged in.

                                        ; When the remote base is disconnected from the originating node, the

                                        ; user will be logged out. The LICENSETAG argument is used to enforce

                                        ; tx frequency limits. See [txlimits] below.

85 = cop,6                              ; Remote base telephone key

 

 

[telemetry]

 

; Telemetry entries can be shared across all repeaters, or defined for each repeater.

; Can be a tone sequence, morse string, or a file

;

; |t - Tone escape sequence

;

; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)

; Single frequencies are created by setting freq1 or freq2 to zero.

;

; |m - Morse escape sequence

;

; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the

; [morse] section.

;

; Follow with an alphanumeric string

;

; |i - Morse ID escape sequence

;

; Sends Morse code at the ID amplitude and ID frequency as defined in the

; [morse] section.

;

; path/to/sound/file/without/extension

;

; Send the sound if in place of a constructed tone. Do not include the file extension

; Example: ct8 = rpt/bloop

; Example: idrecording = rpt/nodenames/1999

 

ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)

ct2 = |t(660,880,150,2048)

ct3 = |t(440,0,150,4096)

ct4 = |t(550,0,150,2048)

ct5 = |t(660,0,150,2048)

ct6 = |t(880,0,150,2048)

ct7 = |t(660,440,150,2048)

ct8 = |t(700,1100,150,2048)

ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)

remotemon = |t(1209,0,50,2048)                                  ; local courtesy tone when receive only

remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000)         ; local courtesy tone when linked Trancieve mode

cmdmode = |t(900,903,200,2048)

functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)

remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)

pfxtone = |t(350,440,30000,3072)

patchup = rpt/callproceeding

patchdown = rpt/callterminated

 

; As far as what the numbers mean,

; (000,000,010,000)

;   |   |   |   |-------amplitude

;   |   |   |-------------duration

;   |   |-------------------Tone 2

;   |-------------------------Tone 1

 

; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.

; Use it for a delay.  Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter)

; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.

 

; Morse code parameters, these are common to all repeaters.

 

[morse]

speed = 20                              ; Approximate speed in WPM

frequency = 800                         ; Morse Telemetry Frequency

amplitude = 4096                        ; Morse Telemetry Amplitude

idfrequency = 1065                      ; Morse ID Frequency

idamplitude = 1024                      ; Morse ID Amplitude

 

;

; This section allows wait times for telemetry events to be adjusted

; A section for wait times can be defined for every repeater

;

 

[wait-times]

telemwait = 2000                        ; Time to wait before sending most telemetry

idwait = 500                            ; Time to wait before starting ID

unkeywait = 2000                        ; Time to wait after unkey before sending CT's and link telemetry

calltermwait = 2000                     ; Time to wait before announcing "call terminated"

 

;

; This is where you define your nodes which cam be connected to.

;

 

[nodes]

; Note, if you are using automatic update for allstar link nodes,

; no allstar link nodes should be defined here. Only place a definition

; for your local nodes, and private (off of allstar link) nodes here.

 

460310 = radio@....0.1:4569/460310,NONE       ; This must be changed to your node number

                                        ; and iax port number if not the default

; Memories for remote bases

 

[memory]

;00 = 146.580,100.0,m

;01 = 147.030,103.5,m+t

;02 = 147.240,103.5,m+t

;03 = 147.765,79.7,m-t

;04 = 146.460,100.0,m

;05 = 146.550,100.0,m

 

; Place command macros here

 

[macro]

;1 = *32011#

;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#

;3 = *32001*32011*32050*32030*32060#

 

 

; Data Acquisition configuration

 

;[daq-list]

;device = device_name1

;device = device_name2

 

;Where: device_name1 and device_name2 are stanzas you define in this file

 

;device = daq-cham-1

 

; Device name

 

;[daq-cham-1]                           ; Defined in [daq-list]

;hwtype = uchameleon                    ; DAQ hardware type

;devnode = /dev/ttyUSB0                 ; DAQ device node (if required)

;1 = inadc                              ; Pin definition for an ADC channel

;2 = inadc

;3 = inadc

;4 = inadc

;5 = inadc

;6 = inadc

;7 = inadc

;8 = inadc

;9 = inp                                ; Pin definition for an input with a weak pullup resistor

;10 = inp

;11 = inp

;12 = inp

;13 = in                                ; Pin definition for an input without a weak pullup resistor

;14 = out                               ; Pin definition for an output

;15 = out

;16 = out

;17 = out

;18 = out

 

;[meter-faces]

 

;face = scale(scalepre,scalediv,scalepost),word/?,...

;

; scalepre = offset to add before dividing with scalediv

; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts).

; scalepost = offset to add after dividing with scalediv

;

;face = range(X-Y:word,X2-Y2:word,...),word/?,...

;face = bit(low-word,high-word),word/?,...

;

; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories,

; or a question mark which is  a placeholder for the measured value.

;

;

; Battery voltage 0-20 volts

;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts

; 4 quadrant wind direction

;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?

; LM34 temperature sensor with 130 deg. F full scale

;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit

; Status poll (non alarmed)

;light = bit(ha/off,ha/on),ha/light,?

 

;[alarms]

;

;tag = device,pin,node,ignorefirst,func-low,func-hi

;

;tag = a unique name for the alarm

;device = daq device to poll

;pin = the device pin to be monitored

;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it

;node = the node number to execute the function on

;func-low = the DTMF function to execute on a high to low transition

;func-high = the DTMF function to execute on a low to high transition

;

; a  '-' as a function name is shorthand for no-operation

;

;door = daq-cham-1,9,1,2017,*7,-

;pwrfail = daq-cham-1,10,0,2017,*911111,-

;

; Control states

; Allow several control operator functions to be changed at once using one command (good for scheduling)

;

;[controlstates]

;statenum = copcmd,[copcmd]...

;0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation

;1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation

;2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation

 

; Scheduler - execute a macro at a given time

 

[schedule]

;dtmf_function =  m h dom mon dow  ; ala cron, star is implied

;2 = 00 00 * * *   ; at midnight, execute macro 2.

 

#includeifexists custom/rpt.conf

 

 

 

 

Analog_Bridge.ini

 

 

; Analog_Bridge configuration file.

;   This file should be placed in either /etc or it can be

;   supplied as a path on the Analog_Bridge command line.

 

; The best way to think of this file is that there are two main sections, the USRP (analog audio) and

; AMBE_AUDIO (compressed audio).  Analog_Bridge will take everything sent to the USRP port and

; encode it for transmission on the AMBE_AUDIO port.  The encoder will use the format defined in ambeMode.

; As you might expect, the reverse direction is defined too.

 

; Analog_Bridge supports include files. More on this later...

include = dvsm.macro

; include = asl.macro

 

; General Section describes settings for Analog_Bridge itself.

[GENERAL]

logLevel = 2                            ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal

 

; Metadata management

exportMetadata = true                   ; Export metadata to USRP partner (transcode setups require this)

transferRootDir = /tmp                  ; Export database files to USRP partner

subscriberFile = /var/lib/dvswitch/subscriber_ids.csv   ; DMR ID to callsign lookup data

 

; General vocoder setup information

decoderFallBack = true                  ; Allow software AMBE decoding if a hardware decoder is not found

useEmulator = false                     ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)

emulatorAddress = 127.0.0.1:2470        ; IP address and port of the md380 server

 

pcmPort = 2222                          ; UDP port to send to the WebProxy

 

; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)

[AMBE_AUDIO]

address = 127.0.0.1                     ; IP address of xx_Bridge

txPort = 31103                          ; Transmit TLV frames to partner on this port

rxPort = 31100                          ; Listen for TLV frames from partner on this port

ambeMode = DMR                          ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)

minTxTimeMS = 2500                      ; Analog -> Digital Minimum time in MS for hang delay (0-10000)

 

; The metadata below is used when ASL is the source since it does not have any concept of digital modes

gatewayDmrId = 1112721                  ; ID to use when transmitting from Analog_Bridge 7 digit ID

repeaterID = 111272123                  ; ID of source repeater 7 digit ID plus 2 digit SSID

txTg = 31676                               ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge

txTs = 2                                ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge

colorCode = 1                           ; Color Code to assign DMR frames

 

; Information for USRP channel driver.  This interface uses PCM to transfer audio information

; There are two typical configurations, ASL and Transcode.  ASL (AllstarLink) is for analog clients connected

; to a digital network.  Transcode is when Analog_Bridge actually points its PCM interfaces back at itself,

; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.

;   When using ASL, this matches the rpt.conf ASL file with a setting like:

;   rxchannel = usrp/127.0.0.1:34001:32001

;   When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover).  Launch

;   each instance with its own ini file.

[USRP]

address = 127.0.0.1                     ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge)

txPort = 32001                          ; Transmit USRP frames on this port

rxPort = 34001                          ; Listen for USRP frames on this port

usrpAudio = AUDIO_UNITY                 ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)

usrpGain = 1.10                         ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

usrpAGC = -20,10,100                    ; Set the agc threshold (db), slope (db) and decay (ms)

tlvAudio = AUDIO_UNITY                  ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)

tlvGain = 0.35                          ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)

 

[MACROS]

 

; Where the macros are

; xxxx=yyyy

; xxxx is the dial string to match

; yyyy is the command line to execute

 

; xxxx must be preceded by a *

; xxxx can be any string (alphanumeric)

; yyyy is the command to execute

; yyyy will replace xxxx in the dial string

; arguments follow the macro name with a # delimiter

 

; For example using macro "5678" above would look like:

; *5678#9876

 

; Which would invoke:

; echo 9876

 

; Information for DV3000 hardware decoder

;   There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)

;   Use top server and port if using AMBEServer

;   Use bottom server/port and serial = true if using the DV3000u (thumbdv)

;   Did you run AMBETest4.py before using this?

[DV3000]

address = 127.0.0.1                   ; IP address of AMBEServer

rxPort = 2460                         ; Port of AMBEServer

; address = /dev/ttyUSB0              ; Device of DV3000U on this machine

; baud = 460800                       ; Baud rate of the dongle (230400 or 460800)

; serial = true                       ; Use serial=true f

 

 

 

 

 


Steve N4IRS
 

You have 2 channel drivers uncommented:

rxchannel = dahdi/pseudo                ; No radio (hub) <--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB
; rxchannel = Pi/1                      ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999            ; USBRadio (DSP)
; rxchannel = Dahdi/1                   ; PCI Quad card
; rxchannel = Beagle/1                  ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999                ; RTCM device

On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote:

Can you look at this as well…..

 

I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that.

 

Steve

 

 

; Your Repeater

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

[460310]                                        ; Change this to your assigned node number

 

                                        ; Must also be enabled in modules.conf

                                        ; Rx audio/signalling channel. Choose ONLY 1 per node stanza

 

                                        ; Enable the selected channel driver in modules.conf !!!

rxchannel = dahdi/pseudo                ; No radio (hub)

; rxchannel = SimpleUSB/usb_1999        ; SimpleUSB

; rxchannel = Pi/1                      ; Raspberry Pi PiTA

; rxchannel = Radio/usb_1999            ; USBRadio (DSP)

; rxchannel = Dahdi/1                   ; PCI Quad card

; rxchannel = Beagle/1                  ; BeagleBoard

rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP

; rxchannel = Voter/1999                ; RTCM device

 

 

duplex = 1                              ; 0 = Half duplex with no telemetry tones or hang time.

                                        ;     Special Case: Full duplex if linktolink is set to yes.

                                        ;     This mode is preferred when interfacing with an external multiport repeater controller.

                                        ;     Comment out idrecording and idtalkover to suppress IDs also

                                        ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio.

                                        ;     This mode is preferred when interfacing a simplex node.

                                        ; 2 = Full Duplex with telemetry tones and hang time.

                                        ;     This mode is preferred when interfacing a repeater.

                                        ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio.

                                        ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.

 

linktolink = no                         ; disables forcing physical half-duplex operation of main repeater while

                                        ; still keeping half-duplex semantics (optional)

 

linkmongain = 0                         ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received.

                                        ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db.

                                        ; If linkmongain set to a positive number monitored audio will increase by the set amount in db.

                                        ; The value of linkmongain is in db. The default value is 0 db.

 

erxgain = -3                            ; Echolink receive gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

etxgain = 3                             ; Echolink transmit gain adjustment

                                        ; Note: Gain is in db-volts (20logVI/VO)

;eannmode = 1                           ; 1 = Say only node number on echolink connects (default = 1)

                                        ; 2 = say phonetic call sign only on echolink connects

                                        ; 3 = say phonetic call sign and node number on echolink connects

 

;controlstates = controlstates          ; system control state stanza

 

scheduler = schedule                    ; scheduler stanza

functions = functions                   ; Repeater Function stanza

phone_functions = functions             ; Phone Function stanza

link_functions = functions              ; Link Function stanza

 

telemetry = telemetry                   ; Telemetry stanza

morse = morse                           ; Morse stanza

wait_times = wait-times                 ; Wait times stanza

 

context = radio                         ; dialing context for phone

callerid = "Repeater" <0000000000>      ; callerid for phone calls

accountcode = RADIO                     ; account code (optional)

 

hangtime = 5000                         ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms)

althangtime = 4000                      ; longer squelch tail

totime = 180000                         ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)

 

idrecording = |iWA4XYZ                  ; cording or morse string see http://ohnosec.org/drupal/node/87

idtalkover = |iWA4XYZ                   ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129

                                        ; See Telemetry section Example: idrecording = rpt/nodenames/1999

idtime = 540000                         ; id interval time (in ms) (optional) Default 5 minutes (300000 ms)

politeid = 30000                        ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)

 

unlinkedct = ct2                        ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none)

remotect = ct3                          ; remote linked courtesy tone (indicates a remote is in the list of links)

linkunkeyct = ct8                       ; sent when a transmission received over the link unkeys

;nolocallinkct = 0                      ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).

 

;connpgm = yourconnectprogram           ; Disabled. Execute a program you specify on connect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being connected to us (them)

;discpgm = yourdisconnectprogram        ; Disabled. Execute a program you specify on disconnect. (default)

                                        ; passes 2 command line arguments to your program:

                                        ; 1. node number in this stanza (us)

                                        ; 2. node number being disconnected from us (them)

 

;lnkactenable = 0                       ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.

 

;lnkacttime = 1800                      ; Link activity timer time in seconds.

;lnkactmacro = *52                      ; Function to execute when link activity timer expires.

;lnkacttimerwarn = 30seconds            ; Message to play when the link activity timer has 30 seconds left.

 

;remote_inact_timeout =                 ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60)

;remote_timeout =                       ; Session time out for remote base. Set to 0 to disable. (60 * 60)

;remote_timeout_warning_freq =          ; 30

;remote_timeout_warning =               ; (3 * 60)

 

;nounkeyct = 0                          ; Set to a 1 to eliminate courtesy tones and associated delays.

 

holdofftelem = 0                        ; Hold off all telemetry when signal is present on receiver or from connected nodes

                                        ; except when an ID needs to be done and there is a signal coming from a connected node.

 

telemdefault = 0                        ; 0 = telemetry output off

                                        ; 1 = telemetry output on (default = 1)

                                        ; 2 = timed telemetry output on command execution and for a short time thereafter.

 

telemdynamic = 1                        ; 0 = disallow users to change the local telemetry setting with a COP command,

                                        ; 1 = Allow users to change the setting with a COP command. (default = 1)

 

;beaconing = 0                          ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)

 

parrotmode = 0                          ; 0 = Parrot Off (default = 0)

                                        ; 1 = Parrot On Command

                                        ; 2 = Parrot Always

                                        ; 3 = Parrot Once by Command

 

parrottime = 1000                       ; Set the amount of time in milliseconds

                                        ; to wait before parroting what was received

 

;rxnotch=1065,40                        ; (Optional) Notch a particular frequency for a specified

                                        ; b/w. app_rpt must have been compiled with

                                        ; the notch option

 

startup_macro =

 

; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign   ; Point to alternate nodename sound directory

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

; Need more information on these

 

;extnodes = extnodes-different  ; section in extnodefile containing dynamic node information (optional)

;extnodefile = /foo/nodes       ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional)

;extnodefile2 =                 ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes????

;nodenames = /foo/names         ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames

;archivedir = /tmp              ; defines and enables activity recording into specified directory (optional)

;monminblocks = 2048            ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)

 

;                               ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set

;                               ; to support tail messages. They can be omitted otherwise.

;tailmessagetime = 300000       ; Play a tail message every 5 mins

;tailsquashedtime = 30000       ; If squashed by another user,

;                               ; try again after 30 seconds

;tailmessagelist = msg1,msg2    ; list of messages to be played for tail message

 

; alt_functions

; ctgroup

; dphone_functions

; idtime

; iobase

; iospeed

; locallist

; mars          Remote Base

; memory

; nobusyout

; nodes

; nolocallinkct

; notelemtx

; outxlat

; parrot

; propagate_phonedtmf

; rptnode

; rptinactmacro  Macro to execute when inactivity timer expires

; rptinacttime   Inactivity timer time in seconds  (0 seconds disables feature)

; rxnotch       Optional Audio notch

; simplexphonedelay

; tonemacro

; tonezone

; txlimits

 

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

 

; *** Status Reporting ***

 

; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org

statpost_url = http://stats.allstarlink.org/uhandler ; Status updates

 

[functions]

 

; Prefix        Functions

; *1            Disconnect Link

; *2            Monitor Link

; *3            Connect Link

; *4            Command Mode

; *5            Macros

; *6            User Functions

; *7            Connection Status/Functions

; *8            User Functions

; *9            User Functions

; *0            User Functions

 

; *A            User Functions

; *B            User Functions

; *C            User Functions

; *D            User Functions

 

 

; Mandatory Command Codes

; http://docs.allstarlink.org/drupal/node/91

 

1 = ilink,1             ; Disconnect specified link

2 = ilink,2             ; Connect specified link -- monitor only

3 = ilink,3             ; Connect specified link -- tranceive

4 = ilink,4             ; Enter command mode on specified link

70 = ilink,5            ; System status

99 = cop,6              ; PTT (phone mode only)

 

; End Mandatory Command Codes

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

 

; Macro Commands

5 = macro

 

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;