|
Can you look at this as well….. I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that. Steve ; Your Repeater ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [460310] ; Change this to your assigned node number ; Must also be enabled in modules.conf ; Rx audio/signalling channel. Choose ONLY 1 per node stanza ; Enable the selected channel driver in modules.conf !!! rxchannel = dahdi/pseudo ; No radio (hub) ; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_1999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP ; rxchannel = Voter/1999 ; RTCM device duplex = 1 ; 0 = Half duplex with no telemetry tones or hang time. ; Special Case: Full duplex if linktolink is set to yes. ; This mode is preferred when interfacing with an external multiport repeater controller. ; Comment out idrecording and idtalkover to suppress IDs also ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio. ; This mode is preferred when interfacing a simplex node. ; 2 = Full Duplex with telemetry tones and hang time. ; This mode is preferred when interfacing a repeater. ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio. ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down. linktolink = no ; disables forcing physical half-duplex operation of main repeater while ; still keeping half-duplex semantics (optional) linkmongain = 0 ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received. ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db. ; If linkmongain set to a positive number monitored audio will increase by the set amount in db. ; The value of linkmongain is in db. The default value is 0 db. erxgain = -3 ; Echolink receive gain adjustment ; Note: Gain is in db-volts (20logVI/VO) etxgain = 3 ; Echolink transmit gain adjustment ; Note: Gain is in db-volts (20logVI/VO) ;eannmode = 1 ; 1 = Say only node number on echolink connects (default = 1) ; 2 = say phonetic call sign only on echolink connects ; 3 = say phonetic call sign and node number on echolink connects ;controlstates = controlstates ; system control state stanza scheduler = schedule ; scheduler stanza functions = functions ; Repeater Function stanza phone_functions = functions ; Phone Function stanza link_functions = functions ; Link Function stanza telemetry = telemetry ; Telemetry stanza morse = morse ; Morse stanza wait_times = wait-times ; Wait times stanza context = radio ; dialing context for phone callerid = "Repeater" <0000000000> ; callerid for phone calls accountcode = RADIO ; account code (optional) hangtime = 5000 ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms) althangtime = 4000 ; longer squelch tail totime = 180000 ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms) idrecording = |iWA4XYZ ; cording or morse string see http://ohnosec.org/drupal/node/87 idtalkover = |iWA4XYZ ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129 ; See Telemetry section Example: idrecording = rpt/nodenames/1999 idtime = 540000 ; id interval time (in ms) (optional) Default 5 minutes (300000 ms) politeid = 30000 ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000) unlinkedct = ct2 ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none) remotect = ct3 ; remote linked courtesy tone (indicates a remote is in the list of links) linkunkeyct = ct8 ; sent when a transmission received over the link unkeys ;nolocallinkct = 0 ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC). ;connpgm = yourconnectprogram ; Disabled. Execute a program you specify on connect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being connected to us (them) ;discpgm = yourdisconnectprogram ; Disabled. Execute a program you specify on disconnect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being disconnected from us (them) ;lnkactenable = 0 ; Set to 1 to enable the link activity timer. Applicable to standard nodes only. ;lnkacttime = 1800 ; Link activity timer time in seconds. ;lnkactmacro = *52 ; Function to execute when link activity timer expires. ;lnkacttimerwarn = 30seconds ; Message to play when the link activity timer has 30 seconds left. ;remote_inact_timeout = ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60) ;remote_timeout = ; Session time out for remote base. Set to 0 to disable. (60 * 60) ;remote_timeout_warning_freq = ; 30 ;remote_timeout_warning = ; (3 * 60) ;nounkeyct = 0 ; Set to a 1 to eliminate courtesy tones and associated delays. holdofftelem = 0 ; Hold off all telemetry when signal is present on receiver or from connected nodes ; except when an ID needs to be done and there is a signal coming from a connected node. telemdefault = 0 ; 0 = telemetry output off ; 1 = telemetry output on (default = 1) ; 2 = timed telemetry output on command execution and for a short time thereafter. telemdynamic = 1 ; 0 = disallow users to change the local telemetry setting with a COP command, ; 1 = Allow users to change the setting with a COP command. (default = 1) ;beaconing = 0 ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US) parrotmode = 0 ; 0 = Parrot Off (default = 0) ; 1 = Parrot On Command ; 2 = Parrot Always ; 3 = Parrot Once by Command parrottime = 1000 ; Set the amount of time in milliseconds ; to wait before parroting what was received ;rxnotch=1065,40 ; (Optional) Notch a particular frequency for a specified ; b/w. app_rpt must have been compiled with ; the notch option startup_macro = ; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign ; Point to alternate nodename sound directory ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Need more information on these ;extnodes = extnodes-different ; section in extnodefile containing dynamic node information (optional) ;extnodefile = /foo/nodes ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional) ;extnodefile2 = ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes???? ;nodenames = /foo/names ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames ;archivedir = /tmp ; defines and enables activity recording into specified directory (optional) ;monminblocks = 2048 ; Min 1K blocks to be left on partition (will not save monitor output if disk too full) ; ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set ; ; to support tail messages. They can be omitted otherwise. ;tailmessagetime = 300000 ; Play a tail message every 5 mins ;tailsquashedtime = 30000 ; If squashed by another user, ; ; try again after 30 seconds ;tailmessagelist = msg1,msg2 ; list of messages to be played for tail message ; alt_functions ; ctgroup ; dphone_functions ; idtime ; iobase ; iospeed ; locallist ; mars Remote Base ; memory ; nobusyout ; nodes ; nolocallinkct ; notelemtx ; outxlat ; parrot ; propagate_phonedtmf ; rptnode ; rptinactmacro Macro to execute when inactivity timer expires ; rptinacttime Inactivity timer time in seconds (0 seconds disables feature) ; rxnotch Optional Audio notch ; simplexphonedelay ; tonemacro ; tonezone ; txlimits ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; *** Status Reporting *** ; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org statpost_url = http://stats.allstarlink.org/uhandler ; Status updates [functions] ; Prefix Functions ; *1 Disconnect Link ; *2 Monitor Link ; *3 Connect Link ; *4 Command Mode ; *5 Macros ; *6 User Functions ; *7 Connection Status/Functions ; *8 User Functions ; *9 User Functions ; *0 User Functions ; *A User Functions ; *B User Functions ; *C User Functions ; *D User Functions ; Mandatory Command Codes ; http://docs.allstarlink.org/drupal/node/91 1 = ilink,1 ; Disconnect specified link 2 = ilink,2 ; Connect specified link -- monitor only 3 = ilink,3 ; Connect specified link -- tranceive 4 = ilink,4 ; Enter command mode on specified link 70 = ilink,5 ; System status 99 = cop,6 ; PTT (phone mode only) ; End Mandatory Command Codes ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Macro Commands 5 = macro ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Autopatch Commands ; Note, This may be a good place for other 2 digit frequently used commands 61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000 ; Autopatch up 62 = autopatchdn ; Autopatch down ; autopatchup can optionally take comma delimited setting=value pairs: ; context = string ; Override default context with "string" ; dialtime = ms ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second) ; farenddisconnect = 1 ; Automatically disconnect when called party hangs up ; noct = 1 ; Don't send repeater courtesy tone during autopatch calls ; quiet = 1 ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Status Commands ; 1 - Force ID (global) ; 2 - Give Time of Day (global) ; 3 - Give software Version (global) ; 4 - Give GPS location info ; 5 - Last (dtmf) user ; 11 - Force ID (local only) ; 12 - Give Time of Day (local only) 721 = status,1 ; Force ID (global) 722 = status,2 ; Give Time of Day (global) 723 = status,3 ; Give software Version (global) 724 = status,4 ; Give GPS location info 725 = status,5 ; Last (dtmf) user 711 = status,11 ; Force ID (local only) 712 = status,12 ; Give Time of Day (local only) ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Link Commands ; 1 - Disconnect specified link ; 2 - Connect specified link -- monitor only ; 3 - Connect specified link -- tranceive ; 4 - Enter command mode on specified link ; 5 - System status ; 6 - Disconnect all links ; 7 - Last Node to Key Up ; 8 - Connect specified link -- local monitor only ; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc. ; 10 - Disconnect all RANGER links (except permalinks) ; 11 - Disconnect a previously permanently connected link ; 12 - Permanently connect specified link -- monitor only ; 13 - Permanently connect specified link -- tranceive ; 15 - Full system status (all nodes) ; 16 - Reconnect links disconnected with "disconnect all links" ; 17 - MDC test (for diag purposes) ; 18 - Permanently Connect specified link -- local monitor only ; ilink commands 1 through 5 are defined in the Mandatory Command section 806 = ilink,6 ; Disconnect all links 807 = ilink,7 ; Last Node to Key Up 808 = ilink,8 ; Connect specified link -- local monitor only 809 = ilink,9,1999,"Testing" ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes 810 = ilink,10 ; Disconnect all RANGER links (except permalinks) 811 = ilink,11 ; Disconnect a previously permanently connected link 812 = ilink,12 ; Permanently connect specified link -- monitor only 813 = ilink,13 ; Permanently connect specified link -- tranceive 815 = ilink,15 ; Full system status (all nodes) 816 = ilink,16 ; Reconnect links disconnected with "disconnect all links" 817 = ilink,17 ; MDC test (for diag purposes) 818 = ilink 18 ; Permanently Connect specified link -- local monitor only ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Control operator (cop) functions. Change these to something other than these codes listed below! 901 = cop,1 ; System warm boot 902 = cop,2 ; System enable 903 = cop,3 ; System disable 904 = cop,4 ; Test tone on/off (toggle) 905 = cop,5 ; Dump system variables on console (debug use only) 907 = cop,7 ; Time out timer enable 908 = cop,8 ; Time out timer disable 909 = cop,9 ; Autopatch enable 910 = cop,10 ; Autopatch disable 911 = cop,11 ; User linking functions enable 912 = cop,12 ; User linking functions disable 913 = cop,13 ; Query system control state 914 = cop,14 ; Set system control state 915 = cop,15 ; Scheduler enable 916 = cop,16 ; Scheduler disable 917 = cop,17 ; User functions enable (time, id, etc) 918 = cop,18 ; User functions disable 919 = cop,19 ; Select alternate hang time (althangtime) 920 = cop,20 ; Select standard hangtime (hangtime) 921 = cop,21 ; Enable Parrot Mode 922 = cop,22 ; Disable Parrot Mode 923 = cop,23 ; Birdbath (Current Parrot Cleanup/Flush) 924 = cop,24 ; Flush all telemetry 925 = cop,25 ; Query last node un-keyed 926 = cop,26 ; Query all nodes keyed/unkeyed 927 = cop,27 ; Reset DAQ minimum on a pin 928 = cop,28 ; Reset DAQ maximum on a pin 930 = cop,30 ; Recall Memory Setting in Attached Xcvr 931 = cop,31 ; Channel Selector for Parallel Programmed Xcvr 932 = cop,32 ; Touchtone pad test: command + Digit string + # to playback all digits pressed 933 = cop,33 ; Local Telemetry Output Enable 934 = cop,34 ; Local Telemetry Output Disable 935 = cop,35 ; Local Telemetry Output on Demand 936 = cop,36 ; Foreign Link Local Output Path Enable 937 = cop,37 ; Foreign Link Local Output Path Disable 938 = cop,38 ; Foreign Link Local Output Path Follows Local Telemetry 939 = cop,39 ; Foreign Link Local Output Path on Demand 942 = cop,42 ; Echolink announce node # only 943 = cop,43 ; Echolink announce node Callsign only 944 = cop,44 ; Echolink announce node # & Callsign 945 = cop,45 ; Link Activity timer enable 945 = cop,46 ; Link Activity timer disable 947 = cop,47 ; Reset "Link Config Changed" Flag 948 = cop,48 ; Send Page Tone (Tone specs separated by parenthesis) 949 = cop,49 ; Disable incoming connections (control state noice) 950 = cop,50 ; Enable incoming connections (control state noicd) 951 = cop,51 ; Enable sleep mode 952 = cop,52 ; Disable sleep mode 953 = cop,53 ; Wake up from sleep 954 = cop,54 ; Go to sleep 955 = cop,55 ; Parrot Once if parrot mode is disabled 956 = cop,56 ; Rx CTCSS Enable 957 = cop,57 ; Rx CTCSS Disable 958 = cop.58 ; Tx CTCSS On Input only Enable 959 = cop,59 ; Tx CTCSS On Input only Disable 960 = cop,60 ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode]) ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F. ; DestID and subcode are only specified for the 'C' type message. ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of ; the radio being called, and the subcodes are as follows: ; Subcode '8205' is Voice Selective Call for Spectra ('Call') ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or ; Astro-Saber('Call') ; Subcode '810D' is Call Alert (like Maxtrac 'CA') 961 = cop,61 ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....) 962 = cop,62 ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....) 963 = cop,63 ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR]) 964 = cop,64 ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR]) 965 = cop,65 ; Send POCSAG page (equipped channel types only) [functions-remote] 0 = remote,1 ; Retrieve Memory 1 = remote,2 ; Set freq. 2 = remote,3 ; Set tx PL tone 3 = remote,4 ; Set rx PL tone 40 = remote,100 ; Rx PL off 41 = remote,101 ; Rx PL on 42 = remote,102 ; Tx PL off 43 = remote,103 ; Tx PL on 44 = remote,104 ; Low Power 45 = remote,105 ; Medium Power 46 = remote,106 ; High Power 711 = remote,107 ; Bump -20 714 = remote,108 ; Bump -100 717 = remote,109 ; Bump -500 713 = remote,110 ; Bump +20 716 = remote,111 ; Bump +100 719 = remote,112 ; Bump +500 721 = remote,113 ; Scan - slow 724 = remote,114 ; Scan - quick 727 = remote,115 ; Scan - fast 723 = remote,116 ; Scan + slow 726 = remote,117 ; Scan + quick 729 = remote,118 ; Scan + fast 79 = remote,119 ; Tune 51 = remote,5 ; Long status query 52 = remote,140 ; Short status query 67 = remote,210 ; Send a * 69 = remote,211 ; Send a # ;91 = remote,99,CALLSIGN,LICENSETAG ; Remote base login. ; Define a different dtmf sequence for each user which is ; authorized to use the remote base to control access to it. ; For examble 9139583=remote,99,WB6NIL,G would grant access to ; the remote base and announce WB6NIL as being logged in. ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to ; the remote base and announce WA6ZFT as being logged in. ; When the remote base is disconnected from the originating node, the ; user will be logged out. The LICENSETAG argument is used to enforce ; tx frequency limits. See [txlimits] below. 85 = cop,6 ; Remote base telephone key [telemetry] ; Telemetry entries can be shared across all repeaters, or defined for each repeater. ; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape sequence ; ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) ; Single frequencies are created by setting freq1 or freq2 to zero. ; ; |m - Morse escape sequence ; ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ; ; |i - Morse ID escape sequence ; ; Sends Morse code at the ID amplitude and ID frequency as defined in the ; [morse] section. ; ; path/to/sound/file/without/extension ; ; Send the sound if in place of a constructed tone. Do not include the file extension ; Example: ct8 = rpt/bloop ; Example: idrecording = rpt/nodenames/1999 ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2 = |t(660,880,150,2048) ct3 = |t(440,0,150,4096) ct4 = |t(550,0,150,2048) ct5 = |t(660,0,150,2048) ct6 = |t(880,0,150,2048) ct7 = |t(660,440,150,2048) ct8 = |t(700,1100,150,2048) ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0) remotemon = |t(1209,0,50,2048) ; local courtesy tone when receive only remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local courtesy tone when linked Trancieve mode cmdmode = |t(900,903,200,2048) functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048) pfxtone = |t(350,440,30000,3072) patchup = rpt/callproceeding patchdown = rpt/callterminated ; As far as what the numbers mean, ; (000,000,010,000) ; | | | |-------amplitude ; | | |-------------duration ; | |-------------------Tone 2 ; |-------------------------Tone 1 ; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude. ; Use it for a delay. Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter) ; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048. ; Morse code parameters, these are common to all repeaters. [morse] speed = 20 ; Approximate speed in WPM frequency = 800 ; Morse Telemetry Frequency amplitude = 4096 ; Morse Telemetry Amplitude idfrequency = 1065 ; Morse ID Frequency idamplitude = 1024 ; Morse ID Amplitude ; ; This section allows wait times for telemetry events to be adjusted ; A section for wait times can be defined for every repeater ; [wait-times] telemwait = 2000 ; Time to wait before sending most telemetry idwait = 500 ; Time to wait before starting ID unkeywait = 2000 ; Time to wait after unkey before sending CT's and link telemetry calltermwait = 2000 ; Time to wait before announcing "call terminated" ; ; This is where you define your nodes which cam be connected to. ; [nodes] ; Note, if you are using automatic update for allstar link nodes, ; no allstar link nodes should be defined here. Only place a definition ; for your local nodes, and private (off of allstar link) nodes here. 460310 = radio@....0.1:4569/460310,NONE ; This must be changed to your node number ; and iax port number if not the default ; Memories for remote bases [memory] ;00 = 146.580,100.0,m ;01 = 147.030,103.5,m+t ;02 = 147.240,103.5,m+t ;03 = 147.765,79.7,m-t ;04 = 146.460,100.0,m ;05 = 146.550,100.0,m ; Place command macros here [macro] ;1 = *32011# ;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030# ;3 = *32001*32011*32050*32030*32060# ; Data Acquisition configuration ;[daq-list] ;device = device_name1 ;device = device_name2 ;Where: device_name1 and device_name2 are stanzas you define in this file ;device = daq-cham-1 ; Device name ;[daq-cham-1] ; Defined in [daq-list] ;hwtype = uchameleon ; DAQ hardware type ;devnode = /dev/ttyUSB0 ; DAQ device node (if required) ;1 = inadc ; Pin definition for an ADC channel ;2 = inadc ;3 = inadc ;4 = inadc ;5 = inadc ;6 = inadc ;7 = inadc ;8 = inadc ;9 = inp ; Pin definition for an input with a weak pullup resistor ;10 = inp ;11 = inp ;12 = inp ;13 = in ; Pin definition for an input without a weak pullup resistor ;14 = out ; Pin definition for an output ;15 = out ;16 = out ;17 = out ;18 = out ;[meter-faces] ;face = scale(scalepre,scalediv,scalepost),word/?,... ; ; scalepre = offset to add before dividing with scalediv ; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts). ; scalepost = offset to add after dividing with scalediv ; ;face = range(X-Y:word,X2-Y2:word,...),word/?,... ;face = bit(low-word,high-word),word/?,... ; ; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories, ; or a question mark which is a placeholder for the measured value. ; ; ; Battery voltage 0-20 volts ;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts ; 4 quadrant wind direction ;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,? ; LM34 temperature sensor with 130 deg. F full scale ;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit ; Status poll (non alarmed) ;light = bit(ha/off,ha/on),ha/light,? ;[alarms] ; ;tag = device,pin,node,ignorefirst,func-low,func-hi ; ;tag = a unique name for the alarm ;device = daq device to poll ;pin = the device pin to be monitored ;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it ;node = the node number to execute the function on ;func-low = the DTMF function to execute on a high to low transition ;func-high = the DTMF function to execute on a low to high transition ; ; a '-' as a function name is shorthand for no-operation ; ;door = daq-cham-1,9,1,2017,*7,- ;pwrfail = daq-cham-1,10,0,2017,*911111,- ; ; Control states ; Allow several control operator functions to be changed at once using one command (good for scheduling) ; ;[controlstates] ;statenum = copcmd,[copcmd]... ;0 = rptena,lnkena,apena,totena,ufena,noicd ; Normal operation ;1 = rptena,lnkena,apdis,totdis,ufena,noice ; Net and news operation ;2 = rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only operation ; Scheduler - execute a macro at a given time [schedule] ;dtmf_function = m h dom mon dow ; ala cron, star is implied ;2 = 00 00 * * * ; at midnight, execute macro 2. #includeifexists custom/rpt.conf Analog_Bridge.ini ; Analog_Bridge configuration file. ; This file should be placed in either /etc or it can be ; supplied as a path on the Analog_Bridge command line. ; The best way to think of this file is that there are two main sections, the USRP (analog audio) and ; AMBE_AUDIO (compressed audio). Analog_Bridge will take everything sent to the USRP port and ; encode it for transmission on the AMBE_AUDIO port. The encoder will use the format defined in ambeMode. ; As you might expect, the reverse direction is defined too. ; Analog_Bridge supports include files. More on this later... include = dvsm.macro ; include = asl.macro ; General Section describes settings for Analog_Bridge itself. [GENERAL] logLevel = 2 ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal ; Metadata management exportMetadata = true ; Export metadata to USRP partner (transcode setups require this) transferRootDir = /tmp ; Export database files to USRP partner subscriberFile = /var/lib/dvswitch/subscriber_ids.csv ; DMR ID to callsign lookup data ; General vocoder setup information decoderFallBack = true ; Allow software AMBE decoding if a hardware decoder is not found useEmulator = false ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN) emulatorAddress = 127.0.0.1:2470 ; IP address and port of the md380 server pcmPort = 2222 ; UDP port to send to the WebProxy ; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC) [AMBE_AUDIO] address = 127.0.0.1 ; IP address of xx_Bridge txPort = 31103 ; Transmit TLV frames to partner on this port rxPort = 31100 ; Listen for TLV frames from partner on this port ambeMode = DMR ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format) minTxTimeMS = 2500 ; Analog -> Digital Minimum time in MS for hang delay (0-10000) ; The metadata below is used when ASL is the source since it does not have any concept of digital modes gatewayDmrId = 1112721 ; ID to use when transmitting from Analog_Bridge 7 digit ID repeaterID = 111272123 ; ID of source repeater 7 digit ID plus 2 digit SSID txTg = 31676 ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge txTs = 2 ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge colorCode = 1 ; Color Code to assign DMR frames ; Information for USRP channel driver. This interface uses PCM to transfer audio information ; There are two typical configurations, ASL and Transcode. ASL (AllstarLink) is for analog clients connected ; to a digital network. Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, ; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture. ; When using ASL, this matches the rpt.conf ASL file with a setting like: ; rxchannel = usrp/127.0.0.1:34001:32001 ; When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover). Launch ; each instance with its own ini file. [USRP] address = 127.0.0.1 ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge) txPort = 32001 ; Transmit USRP frames on this port rxPort = 34001 ; Listen for USRP frames on this port usrpAudio = AUDIO_UNITY ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC) usrpGain = 1.10 ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY) usrpAGC = -20,10,100 ; Set the agc threshold (db), slope (db) and decay (ms) tlvAudio = AUDIO_UNITY ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) tlvGain = 0.35 ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY) [MACROS] ; Where the macros are ; xxxx=yyyy ; xxxx is the dial string to match ; yyyy is the command line to execute ; xxxx must be preceded by a * ; xxxx can be any string (alphanumeric) ; yyyy is the command to execute ; yyyy will replace xxxx in the dial string ; arguments follow the macro name with a # delimiter ; For example using macro "5678" above would look like: ; *5678#9876 ; Which would invoke: ; echo 9876 ; Information for DV3000 hardware decoder ; There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware) ; Use top server and port if using AMBEServer ; Use bottom server/port and serial = true if using the DV3000u (thumbdv) ; Did you run AMBETest4.py before using this? [DV3000] address = 127.0.0.1 ; IP address of AMBEServer rxPort = 2460 ; Port of AMBEServer ; address = /dev/ttyUSB0 ; Device of DV3000U on this machine ; baud = 460800 ; Baud rate of the dongle (230400 or 460800) ; serial = true ; Use serial=true f
|
|
|
Steve N4IRS
You have 2 channel drivers uncommented:
rxchannel = dahdi/pseudo ; No radio (hub)
<--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel = Pi/1 ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999 ; USBRadio (DSP)
; rxchannel = Dahdi/1 ; PCI Quad card
; rxchannel = Beagle/1 ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999 ; RTCM device
toggle quoted messageShow quoted text
On 2/14/21 2:34 PM, Steve Siesel
[K4KSA] wrote:
Can you look at this as well…..
I cannot get ASL<> AB to talk….Here
is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676
make it in the logs of AB and MB. When able to talk on Allstar
via Corey’s WS, I see the transmission in Allstar but nothing
past that.
Steve
; Your Repeater
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
[460310]
; Change this to your assigned node number
; Must also be enabled in modules.conf
; Rx audio/signalling channel. Choose ONLY 1 per node stanza
; Enable the selected channel driver in modules.conf !!!
rxchannel =
dahdi/pseudo ; No radio (hub)
; rxchannel =
SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel =
Pi/1 ; Raspberry Pi PiTA
; rxchannel =
Radio/usb_1999 ; USBRadio (DSP)
; rxchannel =
Dahdi/1 ; PCI Quad card
; rxchannel =
Beagle/1 ; BeagleBoard
rxchannel =
USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel =
Voter/1999 ; RTCM device
duplex =
1 ; 0 = Half duplex with no
telemetry tones or hang time.
; Special Case: Full duplex if linktolink is set to yes.
; This mode is preferred when interfacing with an
external multiport repeater controller.
; Comment out idrecording and idtalkover to suppress IDs
also
; 1 = Half duplex with telemetry tones and hang time. Does
not repeat audio.
; This mode is preferred when interfacing a simplex
node.
; 2 = Full Duplex with telemetry tones and hang time.
; This mode is preferred when interfacing a repeater.
; 3 = Full Duplex with telemetry tones and hang time, but no
repeated audio.
; 4 = Full Duplex with telemetry tones and hang time.
Repeated audio only when the autopatch is down.
linktolink =
no ; disables forcing physical
half-duplex operation of main repeater while
; still keeping half-duplex semantics (optional)
linkmongain =
0 ; Link Monitor Gain adjusts the
audio level of monitored nodes when a signal from another
node or the local receiver is received.
; If linkmongain is set to a negative number the monitored
audio will decrease by the set amount in db.
; If linkmongain set to a positive number monitored audio
will increase by the set amount in db.
; The value of linkmongain is in db. The default value is 0
db.
erxgain =
-3 ; Echolink receive gain
adjustment
; Note: Gain is in db-volts (20logVI/VO)
etxgain =
3 ; Echolink transmit gain
adjustment
; Note: Gain is in db-volts
(20logVI/VO)
;eannmode =
1 ; 1 = Say only node number on
echolink connects (default = 1)
; 2 = say phonetic call sign only on echolink connects
; 3 = say phonetic call sign and
node number on echolink connects
;controlstates =
controlstates ; system control state stanza
scheduler =
schedule ; scheduler stanza
functions =
functions ; Repeater Function stanza
phone_functions =
functions ; Phone Function stanza
link_functions =
functions ; Link Function stanza
telemetry =
telemetry ; Telemetry stanza
morse =
morse ; Morse stanza
wait_times =
wait-times ; Wait times stanza
context =
radio ; dialing context for phone
callerid =
"Repeater" <0000000000> ; callerid for phone
calls
accountcode =
RADIO ; account code (optional)
hangtime =
5000 ; squelch tail hang time (in
ms) (optional, default 5 seconds, 5000 ms)
althangtime =
4000 ; longer squelch tail
totime =
180000 ; transmit time-out time (in
ms) (optional, default 3 minutes 180000 ms)
idrecording =
|iWA4XYZ ; cording or morse string see
http://ohnosec.org/drupal/node/87
idtalkover =
|iWA4XYZ ; Talkover ID (optional) default
is none see http://ohnosec.org/drupal/node/129
; See Telemetry section Example: idrecording =
rpt/nodenames/1999
idtime =
540000 ; id interval time (in ms)
(optional) Default 5 minutes (300000 ms)
politeid =
30000 ; time in milliseconds before
ID timer expires to try and ID in the tail. (optional,
default 30000)
unlinkedct =
ct2 ; Send a this courtesy tone when
the user unkeys if the node is not connected to any other
nodes. (optional, default is none)
remotect =
ct3 ; remote linked courtesy tone
(indicates a remote is in the list of links)
linkunkeyct =
ct8 ; sent when a transmission
received over the link unkeys
;nolocallinkct =
0 ; Send unlinkedct instead if another
local node is connected to this node (hosted on the same
PC).
;connpgm =
yourconnectprogram ; Disabled. Execute a program
you specify on connect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being connected to us (them)
;discpgm =
yourdisconnectprogram ; Disabled. Execute a program
you specify on disconnect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being disconnected from us (them)
;lnkactenable =
0 ; Set to 1 to enable the link
activity timer. Applicable to standard nodes only.
;lnkacttime =
1800 ; Link activity timer time in
seconds.
;lnkactmacro =
*52 ; Function to execute when link
activity timer expires.
;lnkacttimerwarn =
30seconds ; Message to play when the link
activity timer has 30 seconds left.
;remote_inact_timeout
= ; Specifies the amount of time without
keying from the link. Set to 0 to disable timeout. (15 * 60)
;remote_timeout
= ; Session time out for remote base.
Set to 0 to disable. (60 * 60)
;remote_timeout_warning_freq
= ; 30
;remote_timeout_warning
= ; (3 * 60)
;nounkeyct =
0 ; Set to a 1 to eliminate
courtesy tones and associated delays.
holdofftelem =
0 ; Hold off all telemetry when
signal is present on receiver or from connected nodes
; except when an ID needs to be done and there is a signal
coming from a connected node.
telemdefault =
0 ; 0 = telemetry output off
; 1 = telemetry output on (default = 1)
; 2 = timed telemetry output on command execution and for a
short time thereafter.
telemdynamic =
1 ; 0 = disallow users to change the
local telemetry setting with a COP command,
; 1 = Allow users to change the setting with a COP command.
(default = 1)
;beaconing =
0 ; Send ID regardless of repeater
activity (Required in the UK, but probably illegal in the
US)
parrotmode =
0 ; 0 = Parrot Off (default = 0)
; 1 = Parrot On Command
; 2 = Parrot Always
; 3 = Parrot Once by Command
parrottime =
1000 ; Set the amount of time in
milliseconds
; to wait before parroting what was received
;rxnotch=1065,40
; (Optional) Notch a particular frequency for a specified
; b/w. app_rpt must have been compiled with
; the notch option
startup_macro =
; nodenames =
/var/lib/asterisk/sounds/rpt/nodenames.callsign ; Point to
alternate nodename sound directory
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Need more
information on these
;extnodes =
extnodes-different ; section in extnodefile containing
dynamic node information (optional)
;extnodefile =
/foo/nodes ; Points to nodelist file containing
dynamic node info default = /var/lib/asterisk/rpt_extnodes
(optional)
;extnodefile2
= ; Is this a list of node files? Possible a
list of private nodes or a list of static IPs for known
nodes????
;nodenames =
/foo/names ; locaton of node sound files default =
/var/lib/asterisk/sounds/rpt/nodenames
;archivedir =
/tmp ; defines and enables activity recording
into specified directory (optional)
;monminblocks =
2048 ; Min 1K blocks to be left on partition
(will not save monitor output if disk too full)
;
; The tailmessagetime,tailsquashedtime, and tailmessagelist
need to be set
;
; to support tail messages. They can be omitted otherwise.
;tailmessagetime =
300000 ; Play a tail message every 5 mins
;tailsquashedtime =
30000 ; If squashed by another user,
;
; try again after 30 seconds
;tailmessagelist =
msg1,msg2 ; list of messages to be played for tail
message
; alt_functions
; ctgroup
; dphone_functions
; idtime
; iobase
; iospeed
; locallist
; mars
Remote Base
; memory
; nobusyout
; nodes
; nolocallinkct
; notelemtx
; outxlat
; parrot
;
propagate_phonedtmf
; rptnode
; rptinactmacro
Macro to execute when inactivity timer expires
; rptinacttime
Inactivity timer time in seconds (0 seconds disables
feature)
; rxnotch
Optional Audio notch
; simplexphonedelay
; tonemacro
; tonezone
; txlimits
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; *** Status
Reporting ***
; Comment the
following statpost line stop to reporting of the status of
your node to stats.allstarlink.org
statpost_url =
http://stats.allstarlink.org/uhandler ; Status updates
[functions]
; Prefix
Functions
; *1
Disconnect Link
; *2
Monitor Link
; *3
Connect Link
; *4
Command Mode
; *5
Macros
; *6
User Functions
; *7
Connection Status/Functions
; *8
User Functions
; *9
User Functions
; *0
User Functions
; *A
User Functions
; *B
User Functions
; *C
User Functions
; *D
User Functions
; Mandatory Command
Codes
;
http://docs.allstarlink.org/drupal/node/91
1 =
ilink,1 ; Disconnect specified link
2 =
ilink,2 ; Connect specified link -- monitor only
3 =
ilink,3 ; Connect specified link -- tranceive
4 =
ilink,4 ; Enter command mode on specified link
70 =
ilink,5 ; System status
99 =
cop,6 ; PTT (phone mode only)
; End Mandatory
Command Codes
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Macro Commands
5 = macro
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Autopatch
Commands
; Note, This may be
a good place for other 2 digit frequently used commands
61 =
autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000
; Autopatch up
62 =
autopatchdn
; Autopatch down
; autopatchup can
optionally take comma delimited setting=value pairs:
; context =
string ; Override default context with "string"
; dialtime =
ms ; Specify the max number of milliseconds
between phone number digits (1000 milliseconds = 1 second)
; farenddisconnect
= 1 ; Automatically disconnect when called party
hangs up
; noct =
1 ; Don't send repeater courtesy tone
during autopatch calls
; quiet =
1 ; Don't send dial tone, or connect
messages. Do not send patch down message when called party
hangs up
; Example:
123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Status Commands
; 1 - Force ID
(global)
; 2 - Give Time of
Day (global)
; 3 - Give software
Version (global)
; 4 - Give GPS
location info
; 5 - Last (dtmf)
user
; 11 - Force ID
(local only)
; 12 - Give Time of
Day (local only)
721 =
status,1 ; Force ID (global)
722 =
status,2 ; Give Time of Day (global)
723 =
status,3 ; Give software Version (global)
724 =
status,4 ; Give GPS location info
725 =
status,5 ; Last (dtmf) user
711 =
status,11 ; Force ID (local only)
712 =
status,12 ; Give Time of Day (local only)
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Link Commands
; 1 - Disconnect
specified link
; 2 - Connect
specified link -- monitor only
; 3 - Connect
specified link -- tranceive
; 4 - Enter command
mode on specified link
; 5 - System status
; 6 - Disconnect
all links
; 7 - Last Node to
Key Up
; 8 - Connect
specified link -- local monitor only
; 9 - Send Text
Message (9,<destnodeno or 0 (for all)>,Message Text,
etc.
; 10 - Disconnect
all RANGER links (except permalinks)
; 11 - Disconnect a
previously permanently connected link
; 12 - Permanently
connect specified link -- monitor only
; 13 - Permanently
connect specified link -- tranceive
; 15 - Full system
status (all nodes)
; 16 - Reconnect
links disconnected with "disconnect all links"
; 17 - MDC test
(for diag purposes)
; 18 - Permanently
Connect specified link -- local monitor only
; ilink commands 1
through 5 are defined in the Mandatory Command section
806 =
ilink,6 ; Disconnect all links
807 =
ilink,7 ; Last Node to Key Up
808 =
ilink,8 ; Connect specified link -- local
monitor only
809 =
ilink,9,1999,"Testing" ; would send a text message to
node 1999 replace 1999 with 0 for all connected nodes
810 =
ilink,10 ; Disconnect all RANGER links
(except permalinks)
811 =
ilink,11 ; Disconnect a previously
permanently connected link
812 =
ilink,12 ; Permanently connect specified
link -- monitor only
813 =
ilink,13 ; Permanently connect specified
link -- tranceive
815 =
ilink,15 ; Full system status (all nodes)
816 =
ilink,16 ; Reconnect links disconnected
with "disconnect all links"
817 =
ilink,17 ; MDC test (for diag purposes)
818 = ilink
18 ; Permanently Connect specified link --
local monitor only
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Control operator
(cop) functions. Change these to something other than these
codes listed below!
901 =
cop,1 ; System warm boot
902 =
cop,2 ; System enable
903 =
cop,3 ; System disable
904 =
cop,4 ; Test tone on/off
(toggle)
905 =
cop,5 ; Dump system variables on
console (debug use only)
907 =
cop,7 ; Time out timer enable
908 =
cop,8 ; Time out timer disable
909 =
cop,9 ; Autopatch enable
910 =
cop,10 ; Autopatch disable
911 =
cop,11 ; User linking functions
enable
912 =
cop,12 ; User linking functions
disable
913 =
cop,13 ; Query system control
state
914 =
cop,14 ; Set system control state
915 = cop,15
; Scheduler enable
916 =
cop,16 ; Scheduler disable
917 =
cop,17 ; User functions enable
(time, id, etc)
918 =
cop,18 ; User functions disable
919 =
cop,19 ; Select alternate hang
time (althangtime)
920 =
cop,20 ; Select standard hangtime
(hangtime)
921 =
cop,21 ; Enable Parrot Mode
922 =
cop,22 ; Disable Parrot Mode
923 =
cop,23 ; Birdbath (Current Parrot
Cleanup/Flush)
924 =
cop,24 ; Flush all telemetry
925 =
cop,25 ; Query last node un-keyed
926 =
cop,26 ; Query all nodes
keyed/unkeyed
927 =
cop,27 ; Reset DAQ minimum on a
pin
928 =
cop,28 ; Reset DAQ maximum on a
pin
930 =
cop,30 ; Recall Memory Setting in
Attached Xcvr
931 =
cop,31 ; Channel Selector for
Parallel Programmed Xcvr
932 =
cop,32 ; Touchtone pad test:
command + Digit string + # to playback all digits pressed
933 =
cop,33 ; Local Telemetry Output
Enable
934 =
cop,34 ; Local Telemetry Output
Disable
935 =
cop,35 ; Local Telemetry Output
on Demand
936 =
cop,36 ; Foreign Link Local
Output Path Enable
937 =
cop,37 ; Foreign Link Local
Output Path Disable
938 =
cop,38 ; Foreign Link Local
Output Path Follows Local Telemetry
939 =
cop,39 ; Foreign Link Local
Output Path on Demand
942 =
cop,42 ; Echolink announce node #
only
943 =
cop,43 ; Echolink announce node
Callsign only
944 =
cop,44 ; Echolink announce node #
& Callsign
945 =
cop,45 ; Link Activity timer
enable
945 =
cop,46 ; Link Activity timer
disable
947 =
cop,47 ; Reset "Link Config
Changed" Flag
948 =
cop,48 ; Send Page Tone (Tone
specs separated by parenthesis)
949 =
cop,49 ; Disable incoming
connections (control state noice)
950 =
cop,50 ; Enable incoming
connections (control state noicd)
951 =
cop,51 ; Enable sleep mode
952 =
cop,52 ; Disable sleep mode
953 =
cop,53 ; Wake up from sleep
954 =
cop,54 ; Go to sleep
955 =
cop,55 ; Parrot Once if parrot
mode is disabled
956 =
cop,56 ; Rx CTCSS Enable
957 = cop,57
; Rx CTCSS Disable
958 =
cop.58 ; Tx CTCSS On Input only
Enable
959 =
cop,59 ; Tx CTCSS On Input only
Disable
960 =
cop,60 ; Send MDC-1200 Burst
(cop,60,type,UnitID[,DestID,SubCode])
; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call
; (SelCall or Alert), or 'SX' for STS (ststus), where X is
0-F.
; DestID and subcode are only specified for the 'C' type
message.
; UnitID is the local systems UnitID. DestID is the MDC1200
ID of
; the radio being called, and the subcodes are as follows:
; Subcode '8205' is Voice Selective Call for Spectra
('Call')
; Subcode '8015' is Voice Selective Call for Maxtrac ('SC')
or
; Astro-Saber('Call')
; Subcode '810D' is Call Alert (like Maxtrac 'CA')
961 =
cop,61 ; Send Message to USB to
control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)
962 =
cop,62 ; Send Message to USB to
control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)
963 =
cop,63 ; Send pre-configred
APRSTT notification (cop,63,CALL[,OVERLAYCHR])
964 =
cop,64 ; Send pre-configred
APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])
965 =
cop,65 ; Send POCSAG page
(equipped channel types only)
[functions-remote]
0 =
remote,1 ; Retrieve Memory
1 =
remote,2 ; Set freq.
2 =
remote,3 ; Set tx PL tone
3 =
remote,4 ; Set rx PL tone
40 =
remote,100 ; Rx PL off
41 =
remote,101 ; Rx PL on
42 =
remote,102 ; Tx PL off
43 =
remote,103 ; Tx PL on
44 =
remote,104 ; Low Power
45 =
remote,105 ; Medium Power
46 =
remote,106 ; High Power
711 =
remote,107 ; Bump -20
714 =
remote,108 ; Bump -100
717 =
remote,109 ; Bump -500
713 =
remote,110 ; Bump +20
716 =
remote,111 ; Bump +100
719 =
remote,112 ; Bump +500
721 =
remote,113 ; Scan - slow
724 =
remote,114 ; Scan - quick
727 =
remote,115 ; Scan - fast
723 =
remote,116 ; Scan + slow
726 =
remote,117 ; Scan + quick
729 =
remote,118 ; Scan + fast
79 =
remote,119 ; Tune
51 =
remote,5 ; Long status query
52 =
remote,140 ; Short status query
67 =
remote,210 ; Send a *
69 =
remote,211 ; Send a #
;91 =
remote,99,CALLSIGN,LICENSETAG ; Remote base login.
; Define a different dtmf sequence for each user which is
; authorized to use the remote base to control access to it.
; For examble 9139583=remote,99,WB6NIL,G would grant access
to
; the remote base and announce WB6NIL as being logged in.
; Another entry, 9148351=remote,99,WA6ZFT,E would grant
access to
; the remote base and
announce WA6ZFT as being logged in.
; When the remote base is disconnected from the originating
node, the
; user will be logged out. The LICENSETAG argument is used
to enforce
; tx frequency limits. See [txlimits] below.
85 =
cop,6 ; Remote base telephone
key
[telemetry]
; Telemetry entries
can be shared across all repeaters, or defined for each
repeater.
; Can be a tone
sequence, morse string, or a file
;
; |t - Tone escape
sequence
;
; Tone sequences
consist of 1 or more 4-tuple entries (freq1, freq2,
duration, amplitude)
; Single
frequencies are created by setting freq1 or freq2 to zero.
;
; |m - Morse escape
sequence
;
; Sends Morse code
at the telemetry amplitude and telemetry frequency as
defined in the
; [morse] section.
;
; Follow with an
alphanumeric string
;
; |i - Morse ID
escape sequence
;
; Sends Morse code
at the ID amplitude and ID frequency as defined in the
; [morse] section.
;
;
path/to/sound/file/without/extension
;
; Send the sound if
in place of a constructed tone. Do not include the file
extension
; Example: ct8 =
rpt/bloop
; Example:
idrecording = rpt/nodenames/1999
ct1 =
|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2 =
|t(660,880,150,2048)
ct3 =
|t(440,0,150,4096)
ct4 =
|t(550,0,150,2048)
ct5 =
|t(660,0,150,2048)
ct6 =
|t(880,0,150,2048)
ct7 =
|t(660,440,150,2048)
ct8 =
|t(700,1100,150,2048)
ranger =
|t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)
remotemon =
|t(1209,0,50,2048) ; local
courtesy tone when receive only
remotetx =
|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local
courtesy tone when linked Trancieve mode
cmdmode =
|t(900,903,200,2048)
functcomplete =
|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
remcomplete =
|t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)
pfxtone =
|t(350,440,30000,3072)
patchup =
rpt/callproceeding
patchdown =
rpt/callterminated
; As far as what
the numbers mean,
; (000,000,010,000)
; | | |
|-------amplitude
; | |
|-------------duration
; |
|-------------------Tone 2
;
|-------------------------Tone 1
; So, with 0,0,10,0
That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.
; Use it for a
delay. Fine tuning for how long before telemetry is sent,
in conjunction with the telemdelay parameter)
; The numbers, like
350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of
2048.
; Morse code
parameters, these are common to all repeaters.
[morse]
speed =
20 ; Approximate speed in WPM
frequency =
800 ; Morse Telemetry Frequency
amplitude =
4096 ; Morse Telemetry Amplitude
idfrequency =
1065 ; Morse ID Frequency
idamplitude =
1024 ; Morse ID Amplitude
;
; This section
allows wait times for telemetry events to be adjusted
; A section for
wait times can be defined for every repeater
;
[wait-times]
telemwait =
2000 ; Time to wait before sending
most telemetry
idwait =
500 ; Time to wait before
starting ID
unkeywait =
2000 ; Time to wait after unkey
before sending CT's and link telemetry
calltermwait =
2000 ; Time to wait before announcing
"call terminated"
;
; This is where you
define your nodes which cam be connected to.
;
[nodes]
; Note, if you are
using automatic update for allstar link nodes,
; no allstar link
nodes should be defined here. Only place a definition
; for your local
nodes, and private (off of allstar link) nodes here.
460310 =
radio@....0.1:4569/460310,NONE ; This must be
changed to your node number
; and iax port number if not the default
; Memories for
remote bases
[memory]
;00 =
146.580,100.0,m
;01 =
147.030,103.5,m+t
;02 =
147.240,103.5,m+t
;03 =
147.765,79.7,m-t
;04 =
146.460,100.0,m
;05 =
146.550,100.0,m
; Place command
macros here
[macro]
;1 = *32011#
;2 =
*12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#
;3 =
*32001*32011*32050*32030*32060#
; Data Acquisition
configuration
;[daq-list]
;device =
device_name1
;device =
device_name2
;Where:
device_name1 and device_name2 are stanzas you define in this
file
;device =
daq-cham-1
; Device name
;[daq-cham-1]
; Defined in [daq-list]
;hwtype =
uchameleon ; DAQ hardware type
;devnode =
/dev/ttyUSB0 ; DAQ device node (if required)
;1 =
inadc ; Pin definition for an
ADC channel
;2 = inadc
;3 = inadc
;4 = inadc
;5 = inadc
;6 = inadc
;7 = inadc
;8 = inadc
;9 =
inp ; Pin definition for an
input with a weak pullup resistor
;10 = inp
;11 = inp
;12 = inp
;13 =
in ; Pin definition for an
input without a weak pullup resistor
;14 =
out ; Pin definition for an
output
;15 = out
;16 = out
;17 = out
;18 = out
;[meter-faces]
;face =
scale(scalepre,scalediv,scalepost),word/?,...
;
; scalepre = offset
to add before dividing with scalediv
; scalediv = full
scale/number of whole units (e.g. 256/20 or 12.8 for 20
volts).
; scalepost =
offset to add after dividing with scalediv
;
;face =
range(X-Y:word,X2-Y2:word,...),word/?,...
;face =
bit(low-word,high-word),word/?,...
;
; word/? is either
a word in /var/lib/asterisk/sounds or one of its
subdirectories,
; or a question
mark which is a placeholder for the measured value.
;
;
; Battery voltage
0-20 volts
;batvolts =
scale(0,12.8,0),rpt/thevoltageis,?,ha/volts
; 4 quadrant wind
direction
;winddir =
range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?
; LM34 temperature
sensor with 130 deg. F full scale
;lm34f =
scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit
; Status poll (non
alarmed)
;light =
bit(ha/off,ha/on),ha/light,?
;[alarms]
;
;tag =
device,pin,node,ignorefirst,func-low,func-hi
;
;tag = a unique
name for the alarm
;device = daq
device to poll
;pin = the device
pin to be monitored
;ignorefirstalarm =
set to 1 to throwaway first alarm event, or 0 to report it
;node = the node
number to execute the function on
;func-low = the
DTMF function to execute on a high to low transition
;func-high = the
DTMF function to execute on a low to high transition
;
; a '-' as a
function name is shorthand for no-operation
;
;door =
daq-cham-1,9,1,2017,*7,-
;pwrfail =
daq-cham-1,10,0,2017,*911111,-
;
; Control states
; Allow several
control operator functions to be changed at once using one
command (good for scheduling)
;
;[controlstates]
;statenum =
copcmd,[copcmd]...
;0 =
rptena,lnkena,apena,totena,ufena,noicd ; Normal operation
;1 =
rptena,lnkena,apdis,totdis,ufena,noice ; Net and news
operation
;2 =
rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only
operation
; Scheduler -
execute a macro at a given time
[schedule]
;dtmf_function = m
h dom mon dow ; ala cron, star is implied
;2 = 00 00 * * *
; at midnight, execute macro 2.
#includeifexists
custom/rpt.conf
Analog_Bridge.ini
; Analog_Bridge
configuration file.
; This file
should be placed in either /etc or it can be
; supplied as a
path on the Analog_Bridge command line.
; The best way to
think of this file is that there are two main sections, the
USRP (analog audio) and
; AMBE_AUDIO
(compressed audio). Analog_Bridge will take everything sent
to the USRP port and
; encode it for
transmission on the AMBE_AUDIO port. The encoder will use
the format defined in ambeMode.
; As you might
expect, the reverse direction is defined too.
; Analog_Bridge
supports include files. More on this later...
include =
dvsm.macro
; include =
asl.macro
; General Section
describes settings for Analog_Bridge itself.
[GENERAL]
logLevel =
2 ; Show messages and above 0=No
logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error,
6=Fatal
; Metadata
management
exportMetadata =
true ; Export metadata to USRP partner
(transcode setups require this)
transferRootDir =
/tmp ; Export database files to USRP
partner
subscriberFile =
/var/lib/dvswitch/subscriber_ids.csv ; DMR ID to callsign
lookup data
; General vocoder
setup information
decoderFallBack =
true ; Allow software AMBE decoding if a
hardware decoder is not found
useEmulator =
false ; Use the MD380 AMBE emulator for
AMBE72 (DMR/YSFN/NXDN)
emulatorAddress =
127.0.0.1:2470 ; IP address and port of the md380
server
pcmPort =
2222 ; UDP port to send to the
WebProxy
; Information for
xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address =
127.0.0.1 ; IP address of xx_Bridge
txPort =
31103 ; Transmit TLV frames to
partner on this port
rxPort =
31100 ; Listen for TLV frames from
partner on this port
ambeMode =
DMR ; DMR, DMR_IPSC, DSTAR, NXDN,
P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS =
2500 ; Analog -> Digital Minimum
time in MS for hang delay (0-10000)
; The metadata
below is used when ASL is the source since it does not have
any concept of digital modes
gatewayDmrId =
1112721 ; ID to use when transmitting from
Analog_Bridge 7 digit ID
repeaterID =
111272123 ; ID of source repeater 7 digit
ID plus 2 digit SSID
txTg =
31676 ; TG to use for all
frames sent from Analog_Bridge -> xx_Bridge
txTs =
2 ; Slot to use for frames
sent from Analog_Bridge -> xx_Bridge
colorCode =
1 ; Color Code to assign DMR
frames
; Information for
USRP channel driver. This interface uses PCM to transfer
audio information
; There are two
typical configurations, ASL and Transcode. ASL
(AllstarLink) is for analog clients connected
; to a digital
network. Transcode is when Analog_Bridge actually points
its PCM interfaces back at itself,
; causing a TLV
<-- (pcm <--> pcm) --> TLV type of architecture.
; When using ASL,
this matches the rpt.conf ASL file with a setting like:
; rxchannel =
usrp/127.0.0.1:34001:32001
; When
Transcoding, make two ini files and set txPort equal to the
other instance rxPort (crossover). Launch
; each instance
with its own ini file.
[USRP]
address =
127.0.0.1 ; IP address of USRP partner
(Allstar/Asterisk or another Analog_Bridge)
txPort =
32001 ; Transmit USRP frames on
this port
rxPort =
34001 ; Listen for USRP frames on
this port
usrpAudio =
AUDIO_UNITY ; Digital -> Analog
(AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)
usrpGain =
1.10 ; Gain factor when usrpAudio =
AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
usrpAGC =
-20,10,100 ; Set the agc threshold (db),
slope (db) and decay (ms)
tlvAudio =
AUDIO_UNITY ; Analog -> Digital
(AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain =
0.35 ; Gain factor when tlvAudio =
AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
[MACROS]
; Where the macros
are
; xxxx=yyyy
; xxxx is the dial
string to match
; yyyy is the
command line to execute
; xxxx must be
preceded by a *
; xxxx can be any
string (alphanumeric)
; yyyy is the
command to execute
; yyyy will replace
xxxx in the dial string
; arguments follow
the macro name with a # delimiter
; For example using
macro "5678" above would look like:
; *5678#9876
; Which would
invoke:
; echo 9876
; Information for
DV3000 hardware decoder
; There are two
configuration modes: IP (AMBEServer) and serial (direct
connect hardware)
; Use top server
and port if using AMBEServer
; Use bottom
server/port and serial = true if using the DV3000u (thumbdv)
; Did you run
AMBETest4.py before using this?
[DV3000]
address =
127.0.0.1 ; IP address of AMBEServer
rxPort =
2460 ; Port of AMBEServer
; address =
/dev/ttyUSB0 ; Device of DV3000U on this
machine
; baud =
460800 ; Baud rate of the dongle
(230400 or 460800)
; serial =
true ; Use serial=true f
|
|
|
After restarting AB and Asterisk….also md3890-emu is running Still no Joy…Here is the latest start of Analog_bridge.log I: 2021-02-14 19:43:13.761 Analog_Bridge is starting M: 2021-02-14 19:43:13.762 Setting [MACROS] DMR -> /opt/MMDVM_Bridge/dvswitch.sh mode DMR M: 2021-02-14 19:43:13.762 Setting [MACROS] DSTAR -> /opt/MMDVM_Bridge/dvswitch.sh mode DSTAR M: 2021-02-14 19:43:13.762 Setting [MACROS] NXDN -> /opt/MMDVM_Bridge/dvswitch.sh mode NXDN M: 2021-02-14 19:43:13.762 Setting [MACROS] P25 -> /opt/MMDVM_Bridge/dvswitch.sh mode P25 M: 2021-02-14 19:43:13.762 Setting [MACROS] YSF -> /opt/MMDVM_Bridge/dvswitch.sh mode YSF M: 2021-02-14 19:43:13.762 Setting [MACROS] dbupdate -> /opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles M: 2021-02-14 19:43:13.764 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh M: 2021-02-14 19:43:13.765 Setting [] include -> dvsm.macro M: 2021-02-14 19:43:13.766 Setting [GENERAL] logLevel -> 2 M: 2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata -> true M: 2021-02-14 19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp M: 2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv M: 2021-02-14 19:43:13.768 Setting [GENERAL] decoderFallBack -> true M: 2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator -> false M: 2021-02-14 19:43:13.769 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470 M: 2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort -> 2222 M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1 M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103 M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100 M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500 M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721 M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1 M: 2021-02-14 19:43:13.773 Setting [USRP] address -> 127.0.0.1 M: 2021-02-14 19:43:13.773 Setting [USRP] txPort -> 32001 M: 2021-02-14 19:43:13.773 Setting [USRP] rxPort -> 34001 M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY M: 2021-02-14 19:43:13.774 Setting [USRP] usrpGain -> 1.10 M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100 M: 2021-02-14 19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY M: 2021-02-14 19:43:13.775 Setting [USRP] tlvGain -> 0.35 M: 2021-02-14 19:43:13.776 Setting [DV3000] address -> 127.0.0.1 M: 2021-02-14 19:43:13.776 Setting [DV3000] rxPort -> 2460 I: 2021-02-14 19:43:13.777 Open UDP listener on 127.0.0.1:31100 I: 2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001 M: 2021-02-14 19:43:13.777 Connecting to DV3000 hardware...... W: 2021-02-14 19:43:13.871 DV3000 did not reset at 127.0.0.1:2460 W: 2021-02-14 19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset failed) I: 2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850 I: 2021-02-14 19:43:16.073 Default extended metadata <K4KSA> W: 2021-02-14 19:43:16.073 Using software MBE decoder version 1.2.3 W: 2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE vocoder I: 2021-02-14 19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s) 32001 I: 2021-02-14 19:43:16.074 Sending PCM to clients at 127.0.0.1 on port 2222 I: 2021-02-14 19:43:16.074 Starting TLV --> Analog_Bridge (decoder) --> USRP thread I: 2021-02-14 19:43:16.075 Starting USRP --> Analog_Bridge (encoder) -> TLV thread
From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS Sent: Sunday, February 14, 2021 2:41 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] ASL<>AB You have 2 channel drivers uncommented:
rxchannel = dahdi/pseudo ; No radio (hub) <--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel = Pi/1 ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999 ; USBRadio (DSP)
; rxchannel = Dahdi/1 ; PCI Quad card
; rxchannel = Beagle/1 ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999 ; RTCM device On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote: Can you look at this as well….. I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that. Steve ; Your Repeater ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [460310] ; Change this to your assigned node number ; Must also be enabled in modules.conf ; Rx audio/signalling channel. Choose ONLY 1 per node stanza ; Enable the selected channel driver in modules.conf !!! rxchannel = dahdi/pseudo ; No radio (hub) ; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_1999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP ; rxchannel = Voter/1999 ; RTCM device duplex = 1 ; 0 = Half duplex with no telemetry tones or hang time. ; Special Case: Full duplex if linktolink is set to yes. ; This mode is preferred when interfacing with an external multiport repeater controller. ; Comment out idrecording and idtalkover to suppress IDs also ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio. ; This mode is preferred when interfacing a simplex node. ; 2 = Full Duplex with telemetry tones and hang time. ; This mode is preferred when interfacing a repeater. ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio. ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down. linktolink = no ; disables forcing physical half-duplex operation of main repeater while ; still keeping half-duplex semantics (optional) linkmongain = 0 ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received. ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db. ; If linkmongain set to a positive number monitored audio will increase by the set amount in db. ; The value of linkmongain is in db. The default value is 0 db. erxgain = -3 ; Echolink receive gain adjustment ; Note: Gain is in db-volts (20logVI/VO) etxgain = 3 ; Echolink transmit gain adjustment ; Note: Gain is in db-volts (20logVI/VO) ;eannmode = 1 ; 1 = Say only node number on echolink connects (default = 1) ; 2 = say phonetic call sign only on echolink connects ; 3 = say phonetic call sign and node number on echolink connects ;controlstates = controlstates ; system control state stanza scheduler = schedule ; scheduler stanza functions = functions ; Repeater Function stanza phone_functions = functions ; Phone Function stanza link_functions = functions ; Link Function stanza telemetry = telemetry ; Telemetry stanza morse = morse ; Morse stanza wait_times = wait-times ; Wait times stanza context = radio ; dialing context for phone callerid = "Repeater" <0000000000> ; callerid for phone calls accountcode = RADIO ; account code (optional) hangtime = 5000 ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms) althangtime = 4000 ; longer squelch tail totime = 180000 ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms) idrecording = |iWA4XYZ ; cording or morse string see http://ohnosec.org/drupal/node/87 idtalkover = |iWA4XYZ ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129 ; See Telemetry section Example: idrecording = rpt/nodenames/1999 idtime = 540000 ; id interval time (in ms) (optional) Default 5 minutes (300000 ms) politeid = 30000 ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000) unlinkedct = ct2 ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none) remotect = ct3 ; remote linked courtesy tone (indicates a remote is in the list of links) linkunkeyct = ct8 ; sent when a transmission received over the link unkeys ;nolocallinkct = 0 ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC). ;connpgm = yourconnectprogram ; Disabled. Execute a program you specify on connect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being connected to us (them) ;discpgm = yourdisconnectprogram ; Disabled. Execute a program you specify on disconnect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being disconnected from us (them) ;lnkactenable = 0 ; Set to 1 to enable the link activity timer. Applicable to standard nodes only. ;lnkacttime = 1800 ; Link activity timer time in seconds. ;lnkactmacro = *52 ; Function to execute when link activity timer expires. ;lnkacttimerwarn = 30seconds ; Message to play when the link activity timer has 30 seconds left. ;remote_inact_timeout = ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60) ;remote_timeout = ; Session time out for remote base. Set to 0 to disable. (60 * 60) ;remote_timeout_warning_freq = ; 30 ;remote_timeout_warning = ; (3 * 60) ;nounkeyct = 0 ; Set to a 1 to eliminate courtesy tones and associated delays. holdofftelem = 0 ; Hold off all telemetry when signal is present on receiver or from connected nodes ; except when an ID needs to be done and there is a signal coming from a connected node. telemdefault = 0 ; 0 = telemetry output off ; 1 = telemetry output on (default = 1) ; 2 = timed telemetry output on command execution and for a short time thereafter. telemdynamic = 1 ; 0 = disallow users to change the local telemetry setting with a COP command, ; 1 = Allow users to change the setting with a COP command. (default = 1) ;beaconing = 0 ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US) parrotmode = 0 ; 0 = Parrot Off (default = 0) ; 1 = Parrot On Command ; 2 = Parrot Always ; 3 = Parrot Once by Command parrottime = 1000 ; Set the amount of time in milliseconds ; to wait before parroting what was received ;rxnotch=1065,40 ; (Optional) Notch a particular frequency for a specified ; b/w. app_rpt must have been compiled with ; the notch option startup_macro = ; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign ; Point to alternate nodename sound directory ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Need more information on these ;extnodes = extnodes-different ; section in extnodefile containing dynamic node information (optional) ;extnodefile = /foo/nodes ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional) ;extnodefile2 = ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes???? ;nodenames = /foo/names ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames ;archivedir = /tmp ; defines and enables activity recording into specified directory (optional) ;monminblocks = 2048 ; Min 1K blocks to be left on partition (will not save monitor output if disk too full) ; ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set ; ; to support tail messages. They can be omitted otherwise. ;tailmessagetime = 300000 ; Play a tail message every 5 mins ;tailsquashedtime = 30000 ; If squashed by another user, ; ; try again after 30 seconds ;tailmessagelist = msg1,msg2 ; list of messages to be played for tail message ; alt_functions ; ctgroup ; dphone_functions ; idtime ; iobase ; iospeed ; locallist ; mars Remote Base ; memory ; nobusyout ; nodes ; nolocallinkct ; notelemtx ; outxlat ; parrot ; propagate_phonedtmf ; rptnode ; rptinactmacro Macro to execute when inactivity timer expires ; rptinacttime Inactivity timer time in seconds (0 seconds disables feature) ; rxnotch Optional Audio notch ; simplexphonedelay ; tonemacro ; tonezone ; txlimits ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; *** Status Reporting *** ; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org statpost_url = http://stats.allstarlink.org/uhandler ; Status updates [functions] ; Prefix Functions ; *1 Disconnect Link ; *2 Monitor Link ; *3 Connect Link ; *4 Command Mode ; *5 Macros ; *6 User Functions ; *7 Connection Status/Functions ; *8 User Functions ; *9 User Functions ; *0 User Functions ; *A User Functions ; *B User Functions ; *C User Functions ; *D User Functions ; Mandatory Command Codes ; http://docs.allstarlink.org/drupal/node/91 1 = ilink,1 ; Disconnect specified link 2 = ilink,2 ; Connect specified link -- monitor only 3 = ilink,3 ; Connect specified link -- tranceive 4 = ilink,4 ; Enter command mode on specified link 70 = ilink,5 ; System status 99 = cop,6 ; PTT (phone mode only) ; End Mandatory Command Codes ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Macro Commands 5 = macro ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Autopatch Commands ; Note, This may be a good place for other 2 digit frequently used commands 61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000 ; Autopatch up 62 = autopatchdn ; Autopatch down ; autopatchup can optionally take comma delimited setting=value pairs: ; context = string ; Override default context with "string" ; dialtime = ms ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second) ; farenddisconnect = 1 ; Automatically disconnect when called party hangs up ; noct = 1 ; Don't send repeater courtesy tone during autopatch calls ; quiet = 1 ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Status Commands ; 1 - Force ID (global) ; 2 - Give Time of Day (global) ; 3 - Give software Version (global) ; 4 - Give GPS location info ; 5 - Last (dtmf) user ; 11 - Force ID (local only) ; 12 - Give Time of Day (local only) 721 = status,1 ; Force ID (global) 722 = status,2 ; Give Time of Day (global) 723 = status,3 ; Give software Version (global) 724 = status,4 ; Give GPS location info 725 = status,5 ; Last (dtmf) user 711 = status,11 ; Force ID (local only) 712 = status,12 ; Give Time of Day (local only) ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Link Commands ; 1 - Disconnect specified link ; 2 - Connect specified link -- monitor only ; 3 - Connect specified link -- tranceive ; 4 - Enter command mode on specified link ; 5 - System status ; 6 - Disconnect all links ; 7 - Last Node to Key Up ; 8 - Connect specified link -- local monitor only ; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc. ; 10 - Disconnect all RANGER links (except permalinks) ; 11 - Disconnect a previously permanently connected link ; 12 - Permanently connect specified link -- monitor only ; 13 - Permanently connect specified link -- tranceive ; 15 - Full system status (all nodes) ; 16 - Reconnect links disconnected with "disconnect all links" ; 17 - MDC test (for diag purposes) ; 18 - Permanently Connect specified link -- local monitor only ; ilink commands 1 through 5 are defined in the Mandatory Command section 806 = ilink,6 ; Disconnect all links 807 = ilink,7 ; Last Node to Key Up 808 = ilink,8 ; Connect specified link -- local monitor only 809 = ilink,9,1999,"Testing" ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes 810 = ilink,10 ; Disconnect all RANGER links (except permalinks) 811 = ilink,11 ; Disconnect a previously permanently connected link 812 = ilink,12 ; Permanently connect specified link -- monitor only 813 = ilink,13 ; Permanently connect specified link -- tranceive 815 = ilink,15 ; Full system status (all nodes) 816 = ilink,16 ; Reconnect links disconnected with "disconnect all links" 817 = ilink,17 ; MDC test (for diag purposes) 818 = ilink 18 ; Permanently Connect specified link -- local monitor only ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Control operator (cop) functions. Change these to something other than these codes listed below! 901 = cop,1 ; System warm boot 902 = cop,2 ; System enable 903 = cop,3 ; System disable 904 = cop,4 ; Test tone on/off (toggle) 905 = cop,5 ; Dump system variables on console (debug use only) 907 = cop,7 ; Time out timer enable 908 = cop,8 ; Time out timer disable 909 = cop,9 ; Autopatch enable 910 = cop,10 ; Autopatch disable 911 = cop,11 ; User linking functions enable 912 = cop,12 ; User linking functions disable 913 = cop,13 ; Query system control state 914 = cop,14 ; Set system control state 915 = cop,15 ; Scheduler enable 916 = cop,16 ; Scheduler disable 917 = cop,17 ; User functions enable (time, id, etc) 918 = cop,18 ; User functions disable 919 = cop,19 ; Select alternate hang time (althangtime) 920 = cop,20 ; Select standard hangtime (hangtime) 921 = cop,21 ; Enable Parrot Mode 922 = cop,22 ; Disable Parrot Mode 923 = cop,23 ; Birdbath (Current Parrot Cleanup/Flush) 924 = cop,24 ; Flush all telemetry 925 = cop,25 ; Query last node un-keyed 926 = cop,26 ; Query all nodes keyed/unkeyed 927 = cop,27 ; Reset DAQ minimum on a pin 928 = cop,28 ; Reset DAQ maximum on a pin 930 = cop,30 ; Recall Memory Setting in Attached Xcvr 931 = cop,31 ; Channel Selector for Parallel Programmed Xcvr 932 = cop,32 ; Touchtone pad test: command + Digit string + # to playback all digits pressed 933 = cop,33 ; Local Telemetry Output Enable 934 = cop,34 ; Local Telemetry Output Disable 935 = cop,35 ; Local Telemetry Output on Demand 936 = cop,36 ; Foreign Link Local Output Path Enable 937 = cop,37 ; Foreign Link Local Output Path Disable 938 = cop,38 ; Foreign Link Local Output Path Follows Local Telemetry 939 = cop,39 ; Foreign Link Local Output Path on Demand 942 = cop,42 ; Echolink announce node # only 943 = cop,43 ; Echolink announce node Callsign only 944 = cop,44 ; Echolink announce node # & Callsign 945 = cop,45 ; Link Activity timer enable 945 = cop,46 ; Link Activity timer disable 947 = cop,47 ; Reset "Link Config Changed" Flag 948 = cop,48 ; Send Page Tone (Tone specs separated by parenthesis) 949 = cop,49 ; Disable incoming connections (control state noice) 950 = cop,50 ; Enable incoming connections (control state noicd) 951 = cop,51 ; Enable sleep mode 952 = cop,52 ; Disable sleep mode 953 = cop,53 ; Wake up from sleep 954 = cop,54 ; Go to sleep 955 = cop,55 ; Parrot Once if parrot mode is disabled 956 = cop,56 ; Rx CTCSS Enable 957 = cop,57 ; Rx CTCSS Disable 958 = cop.58 ; Tx CTCSS On Input only Enable 959 = cop,59 ; Tx CTCSS On Input only Disable 960 = cop,60 ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode]) ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F. ; DestID and subcode are only specified for the 'C' type message. ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of ; the radio being called, and the subcodes are as follows: ; Subcode '8205' is Voice Selective Call for Spectra ('Call') ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or ; Astro-Saber('Call') ; Subcode '810D' is Call Alert (like Maxtrac 'CA') 961 = cop,61 ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....) 962 = cop,62 ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....) 963 = cop,63 ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR]) 964 = cop,64 ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR]) 965 = cop,65 ; Send POCSAG page (equipped channel types only) [functions-remote] 0 = remote,1 ; Retrieve Memory 1 = remote,2 ; Set freq. 2 = remote,3 ; Set tx PL tone 3 = remote,4 ; Set rx PL tone 40 = remote,100 ; Rx PL off 41 = remote,101 ; Rx PL on 42 = remote,102 ; Tx PL off 43 = remote,103 ; Tx PL on 44 = remote,104 ; Low Power 45 = remote,105 ; Medium Power 46 = remote,106 ; High Power 711 = remote,107 ; Bump -20 714 = remote,108 ; Bump -100 717 = remote,109 ; Bump -500 713 = remote,110 ; Bump +20 716 = remote,111 ; Bump +100 719 = remote,112 ; Bump +500 721 = remote,113 ; Scan - slow 724 = remote,114 ; Scan - quick 727 = remote,115 ; Scan - fast 723 = remote,116 ; Scan + slow 726 = remote,117 ; Scan + quick 729 = remote,118 ; Scan + fast 79 = remote,119 ; Tune 51 = remote,5 ; Long status query 52 = remote,140 ; Short status query 67 = remote,210 ; Send a * 69 = remote,211 ; Send a # ;91 = remote,99,CALLSIGN,LICENSETAG ; Remote base login. ; Define a different dtmf sequence for each user which is ; authorized to use the remote base to control access to it. ; For examble 9139583=remote,99,WB6NIL,G would grant access to ; the remote base and announce WB6NIL as being logged in. ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to ; the remote base and announce WA6ZFT as being logged in. ; When the remote base is disconnected from the originating node, the ; user will be logged out. The LICENSETAG argument is used to enforce ; tx frequency limits. See [txlimits] below. 85 = cop,6 ; Remote base telephone key [telemetry] ; Telemetry entries can be shared across all repeaters, or defined for each repeater. ; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape sequence ; ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) ; Single frequencies are created by setting freq1 or freq2 to zero. ; ; |m - Morse escape sequence ; ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ; ; |i - Morse ID escape sequence ; ; Sends Morse code at the ID amplitude and ID frequency as defined in the ; [morse] section. ; ; path/to/sound/file/without/extension ; ; Send the sound if in place of a constructed tone. Do not include the file extension ; Example: ct8 = rpt/bloop ; Example: idrecording = rpt/nodenames/1999 ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2 = |t(660,880,150,2048) ct3 = |t(440,0,150,4096) ct4 = |t(550,0,150,2048) ct5 = |t(660,0,150,2048) ct6 = |t(880,0,150,2048) ct7 = |t(660,440,150,2048) ct8 = |t(700,1100,150,2048) ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0) remotemon = |t(1209,0,50,2048) ; local courtesy tone when receive only remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local courtesy tone when linked Trancieve mode cmdmode = |t(900,903,200,2048) functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048) pfxtone = |t(350,440,30000,3072) patchup = rpt/callproceeding patchdown = rpt/callterminated ; As far as what the numbers mean, ; (000,000,010,000) ; | | | |-------amplitude ; | | |-------------duration ; | |-------------------Tone 2 ; |-------------------------Tone 1 ; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude. ; Use it for a delay. Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter) ; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048. ; Morse code parameters, these are common to all repeaters. [morse] speed = 20 ; Approximate speed in WPM frequency = 800 ; Morse Telemetry Frequency amplitude = 4096 ; Morse Telemetry Amplitude idfrequency = 1065 ; Morse ID Frequency idamplitude = 1024 ; Morse ID Amplitude ; ; This section allows wait times for telemetry events to be adjusted ; A section for wait times can be defined for every repeater ; [wait-times] telemwait = 2000 ; Time to wait before sending most telemetry idwait = 500 ; Time to wait before starting ID unkeywait = 2000 ; Time to wait after unkey before sending CT's and link telemetry calltermwait = 2000 ; Time to wait before announcing "call terminated" ; ; This is where you define your nodes which cam be connected to. ; [nodes] ; Note, if you are using automatic update for allstar link nodes, ; no allstar link nodes should be defined here. Only place a definition ; for your local nodes, and private (off of allstar link) nodes here. 460310 = radio@....0.1:4569/460310,NONE ; This must be changed to your node number ; and iax port number if not the default ; Memories for remote bases [memory] ;00 = 146.580,100.0,m ;01 = 147.030,103.5,m+t ;02 = 147.240,103.5,m+t ;03 = 147.765,79.7,m-t ;04 = 146.460,100.0,m ;05 = 146.550,100.0,m ; Place command macros here [macro] ;1 = *32011# ;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030# ;3 = *32001*32011*32050*32030*32060# ; Data Acquisition configuration ;[daq-list] ;device = device_name1 ;device = device_name2 ;Where: device_name1 and device_name2 are stanzas you define in this file ;device = daq-cham-1 ; Device name ;[daq-cham-1] ; Defined in [daq-list] ;hwtype = uchameleon ; DAQ hardware type ;devnode = /dev/ttyUSB0 ; DAQ device node (if required) ;1 = inadc ; Pin definition for an ADC channel ;2 = inadc ;3 = inadc ;4 = inadc ;5 = inadc ;6 = inadc ;7 = inadc ;8 = inadc ;9 = inp ; Pin definition for an input with a weak pullup resistor ;10 = inp ;11 = inp ;12 = inp ;13 = in ; Pin definition for an input without a weak pullup resistor ;14 = out ; Pin definition for an output ;15 = out ;16 = out ;17 = out ;18 = out ;[meter-faces] ;face = scale(scalepre,scalediv,scalepost),word/?,... ; ; scalepre = offset to add before dividing with scalediv ; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts). ; scalepost = offset to add after dividing with scalediv ; ;face = range(X-Y:word,X2-Y2:word,...),word/?,... ;face = bit(low-word,high-word),word/?,... ; ; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories, ; or a question mark which is a placeholder for the measured value. ; ; ; Battery voltage 0-20 volts ;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts ; 4 quadrant wind direction ;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,? ; LM34 temperature sensor with 130 deg. F full scale ;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit ; Status poll (non alarmed) ;light = bit(ha/off,ha/on),ha/light,? ;[alarms] ; ;tag = device,pin,node,ignorefirst,func-low,func-hi ; ;tag = a unique name for the alarm ;device = daq device to poll ;pin = the device pin to be monitored ;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it ;node = the node number to execute the function on ;func-low = the DTMF function to execute on a high to low transition ;func-high = the DTMF function to execute on a low to high transition ; ; a '-' as a function name is shorthand for no-operation ; ;door = daq-cham-1,9,1,2017,*7,- ;pwrfail = daq-cham-1,10,0,2017,*911111,- ; ; Control states ; Allow several control operator functions to be changed at once using one command (good for scheduling) ; ;[controlstates] ;statenum = copcmd,[copcmd]... ;0 = rptena,lnkena,apena,totena,ufena,noicd ; Normal operation ;1 = rptena,lnkena,apdis,totdis,ufena,noice ; Net and news operation ;2 = rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only operation ; Scheduler - execute a macro at a given time [schedule] ;dtmf_function = m h dom mon dow ; ala cron, star is implied ;2 = 00 00 * * * ; at midnight, execute macro 2. #includeifexists custom/rpt.conf Analog_Bridge.ini ; Analog_Bridge configuration file. ; This file should be placed in either /etc or it can be ; supplied as a path on the Analog_Bridge command line. ; The best way to think of this file is that there are two main sections, the USRP (analog audio) and ; AMBE_AUDIO (compressed audio). Analog_Bridge will take everything sent to the USRP port and ; encode it for transmission on the AMBE_AUDIO port. The encoder will use the format defined in ambeMode. ; As you might expect, the reverse direction is defined too. ; Analog_Bridge supports include files. More on this later... include = dvsm.macro ; include = asl.macro ; General Section describes settings for Analog_Bridge itself. [GENERAL] logLevel = 2 ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal ; Metadata management exportMetadata = true ; Export metadata to USRP partner (transcode setups require this) transferRootDir = /tmp ; Export database files to USRP partner subscriberFile = /var/lib/dvswitch/subscriber_ids.csv ; DMR ID to callsign lookup data ; General vocoder setup information decoderFallBack = true ; Allow software AMBE decoding if a hardware decoder is not found useEmulator = false ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN) emulatorAddress = 127.0.0.1:2470 ; IP address and port of the md380 server pcmPort = 2222 ; UDP port to send to the WebProxy ; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC) [AMBE_AUDIO] address = 127.0.0.1 ; IP address of xx_Bridge txPort = 31103 ; Transmit TLV frames to partner on this port rxPort = 31100 ; Listen for TLV frames from partner on this port ambeMode = DMR ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format) minTxTimeMS = 2500 ; Analog -> Digital Minimum time in MS for hang delay (0-10000) ; The metadata below is used when ASL is the source since it does not have any concept of digital modes gatewayDmrId = 1112721 ; ID to use when transmitting from Analog_Bridge 7 digit ID repeaterID = 111272123 ; ID of source repeater 7 digit ID plus 2 digit SSID txTg = 31676 ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge txTs = 2 ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge colorCode = 1 ; Color Code to assign DMR frames ; Information for USRP channel driver. This interface uses PCM to transfer audio information ; There are two typical configurations, ASL and Transcode. ASL (AllstarLink) is for analog clients connected ; to a digital network. Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, ; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture. ; When using ASL, this matches the rpt.conf ASL file with a setting like: ; rxchannel = usrp/127.0.0.1:34001:32001 ; When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover). Launch ; each instance with its own ini file. [USRP] address = 127.0.0.1 ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge) txPort = 32001 ; Transmit USRP frames on this port rxPort = 34001 ; Listen for USRP frames on this port usrpAudio = AUDIO_UNITY ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC) usrpGain = 1.10 ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY) usrpAGC = -20,10,100 ; Set the agc threshold (db), slope (db) and decay (ms) tlvAudio = AUDIO_UNITY ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) tlvGain = 0.35 ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY) [MACROS] ; Where the macros are ; xxxx=yyyy ; xxxx is the dial string to match ; yyyy is the command line to execute ; xxxx must be preceded by a * ; xxxx can be any string (alphanumeric) ; yyyy is the command to execute ; yyyy will replace xxxx in the dial string ; arguments follow the macro name with a # delimiter ; For example using macro "5678" above would look like: ; *5678#9876 ; Which would invoke: ; echo 9876 ; Information for DV3000 hardware decoder ; There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware) ; Use top server and port if using AMBEServer ; Use bottom server/port and serial = true if using the DV3000u (thumbdv) ; Did you run AMBETest4.py before using this? [DV3000] address = 127.0.0.1 ; IP address of AMBEServer rxPort = 2460 ; Port of AMBEServer ; address = /dev/ttyUSB0 ; Device of DV3000U on this machine ; baud = 460800 ; Baud rate of the dongle (230400 or 460800) ; serial = true ; Use serial=true f
|
|
|
Steve N4IRS
Did you fix rpt.conf and did you then restart asterisk?
toggle quoted messageShow quoted text
On 2/14/21 2:46 PM, Steve Siesel
[K4KSA] wrote:
After
restarting AB and Asterisk….also md3890-emu is running
Still no
Joy…Here is the latest start of Analog_bridge.log
I: 2021-02-14
19:43:13.761 Analog_Bridge is starting
M: 2021-02-14
19:43:13.762 Setting [MACROS] DMR ->
/opt/MMDVM_Bridge/dvswitch.sh mode DMR
M: 2021-02-14
19:43:13.762 Setting [MACROS] DSTAR ->
/opt/MMDVM_Bridge/dvswitch.sh mode DSTAR
M: 2021-02-14
19:43:13.762 Setting [MACROS] NXDN ->
/opt/MMDVM_Bridge/dvswitch.sh mode NXDN
M: 2021-02-14
19:43:13.762 Setting [MACROS] P25 ->
/opt/MMDVM_Bridge/dvswitch.sh mode P25
M: 2021-02-14
19:43:13.762 Setting [MACROS] YSF ->
/opt/MMDVM_Bridge/dvswitch.sh mode YSF
M: 2021-02-14
19:43:13.762 Setting [MACROS] dbupdate ->
/opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles
M: 2021-02-14
19:43:13.764 Setting [MACROS] 9876 ->
/opt/Analog_Bridge/parrot.sh
M: 2021-02-14
19:43:13.765 Setting [] include -> dvsm.macro
M: 2021-02-14
19:43:13.766 Setting [GENERAL] logLevel -> 2
M: 2021-02-14
19:43:13.766 Setting [GENERAL] exportMetadata -> true
M: 2021-02-14
19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp
M: 2021-02-14
19:43:13.767 Setting [GENERAL] subscriberFile ->
/var/lib/dvswitch/subscriber_ids.csv
M: 2021-02-14
19:43:13.768 Setting [GENERAL] decoderFallBack -> true
M: 2021-02-14
19:43:13.768 Setting [GENERAL] useEmulator -> false
M: 2021-02-14
19:43:13.769 Setting [GENERAL] emulatorAddress ->
127.0.0.1:2470
M: 2021-02-14
19:43:13.769 Setting [GENERAL] pcmPort -> 2222
M: 2021-02-14
19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1
M: 2021-02-14
19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103
M: 2021-02-14
19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100
M: 2021-02-14
19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR
M: 2021-02-14
19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500
M: 2021-02-14
19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721
M: 2021-02-14
19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123
M: 2021-02-14
19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676
M: 2021-02-14
19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2
M: 2021-02-14
19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1
M: 2021-02-14
19:43:13.773 Setting [USRP] address -> 127.0.0.1
M: 2021-02-14
19:43:13.773 Setting [USRP] txPort -> 32001
M: 2021-02-14
19:43:13.773 Setting [USRP] rxPort -> 34001
M: 2021-02-14
19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY
M: 2021-02-14
19:43:13.774 Setting [USRP] usrpGain -> 1.10
M: 2021-02-14
19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100
M: 2021-02-14
19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY
M: 2021-02-14
19:43:13.775 Setting [USRP] tlvGain -> 0.35
M: 2021-02-14
19:43:13.776 Setting [DV3000] address -> 127.0.0.1
M: 2021-02-14
19:43:13.776 Setting [DV3000] rxPort -> 2460
I: 2021-02-14
19:43:13.777 Open UDP listener on 127.0.0.1:31100
I: 2021-02-14
19:43:13.777 Open USRP on 127.0.0.1:32001
M: 2021-02-14
19:43:13.777 Connecting to DV3000 hardware......
W: 2021-02-14
19:43:13.871 DV3000 did not reset at 127.0.0.1:2460
W: 2021-02-14
19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset
failed)
I: 2021-02-14
19:43:16.072 Subscriber IDs loaded: 187850
I: 2021-02-14
19:43:16.073 Default extended metadata <K4KSA>
W: 2021-02-14
19:43:16.073 Using software MBE decoder version 1.2.3
W: 2021-02-14
19:43:16.073 Using software OP25 IMBE/AMBE vocoder
I: 2021-02-14
19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s)
32001
I: 2021-02-14
19:43:16.074 Sending PCM to clients at 127.0.0.1 on port
2222
I: 2021-02-14
19:43:16.074 Starting TLV --> Analog_Bridge (decoder)
--> USRP thread
I: 2021-02-14
19:43:16.075 Starting USRP --> Analog_Bridge (encoder)
-> TLV thread
You have 2
channel drivers uncommented:
rxchannel = dahdi/pseudo ; No radio (hub)
<--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel = Pi/1 ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999 ; USBRadio (DSP)
; rxchannel = Dahdi/1 ; PCI Quad card
; rxchannel = Beagle/1 ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface
USRP
; rxchannel = Voter/1999 ; RTCM device
On 2/14/21 2:34 PM, Steve Siesel [K4KSA]
wrote:
Can you look at this as well…..
I cannot get ASL<> AB to talk….Here
is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676
make it in the logs of AB and MB. When able to talk on
Allstar via Corey’s WS, I see the transmission in Allstar
but nothing past that.
Steve
; Your Repeater
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
[460310]
; Change this to your assigned node number
; Must also be enabled in modules.conf
; Rx audio/signalling channel. Choose ONLY 1 per node
stanza
; Enable the selected channel driver in modules.conf !!!
rxchannel =
dahdi/pseudo ; No radio (hub)
; rxchannel =
SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel =
Pi/1 ; Raspberry Pi PiTA
; rxchannel =
Radio/usb_1999 ; USBRadio (DSP)
; rxchannel =
Dahdi/1 ; PCI Quad card
; rxchannel =
Beagle/1 ; BeagleBoard
rxchannel =
USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel =
Voter/1999 ; RTCM device
duplex =
1 ; 0 = Half duplex with no
telemetry tones or hang time.
; Special Case: Full duplex if linktolink is set to
yes.
; This mode is preferred when interfacing with an
external multiport repeater controller.
; Comment out idrecording and idtalkover to suppress
IDs also
; 1 = Half duplex with telemetry tones and hang time. Does
not repeat audio.
; This mode is preferred when interfacing a simplex
node.
; 2 = Full Duplex with telemetry tones and hang time.
; This mode is preferred when interfacing a repeater.
; 3 = Full Duplex with telemetry tones and hang time, but
no repeated audio.
; 4 = Full Duplex with telemetry tones and hang time.
Repeated audio only when the autopatch is down.
linktolink =
no ; disables forcing physical
half-duplex operation of main repeater while
; still keeping half-duplex semantics (optional)
linkmongain =
0 ; Link Monitor Gain adjusts the
audio level of monitored nodes when a signal from another
node or the local receiver is received.
; If linkmongain is set to a negative number the monitored
audio will decrease by the set amount in db.
; If linkmongain set to a positive number monitored audio
will increase by the set amount in db.
; The value of linkmongain is in db. The default value is
0 db.
erxgain =
-3 ; Echolink receive gain
adjustment
; Note: Gain is in db-volts (20logVI/VO)
etxgain =
3 ; Echolink transmit gain
adjustment
; Note: Gain is in
db-volts (20logVI/VO)
;eannmode =
1 ; 1 = Say only node number on
echolink connects (default = 1)
; 2 = say phonetic call sign only on echolink connects
; 3 = say phonetic call sign and
node number on echolink connects
;controlstates =
controlstates ; system control state stanza
scheduler =
schedule ; scheduler stanza
functions =
functions ; Repeater Function stanza
phone_functions =
functions ; Phone Function stanza
link_functions =
functions ; Link Function stanza
telemetry =
telemetry ; Telemetry stanza
morse =
morse ; Morse stanza
wait_times =
wait-times ; Wait times stanza
context =
radio ; dialing context for phone
callerid =
"Repeater" <0000000000> ; callerid for phone
calls
accountcode =
RADIO ; account code (optional)
hangtime =
5000 ; squelch tail hang time (in
ms) (optional, default 5 seconds, 5000 ms)
althangtime =
4000 ; longer squelch tail
totime =
180000 ; transmit time-out time
(in ms) (optional, default 3 minutes 180000 ms)
idrecording =
|iWA4XYZ ; cording or morse string see http://ohnosec.org/drupal/node/87
idtalkover =
|iWA4XYZ ; Talkover ID (optional)
default is none see http://ohnosec.org/drupal/node/129
; See Telemetry section Example: idrecording =
rpt/nodenames/1999
idtime =
540000 ; id interval time (in ms)
(optional) Default 5 minutes (300000 ms)
politeid =
30000 ; time in milliseconds before
ID timer expires to try and ID in the tail. (optional,
default 30000)
unlinkedct =
ct2 ; Send a this courtesy tone
when the user unkeys if the node is not connected to any
other nodes. (optional, default is none)
remotect =
ct3 ; remote linked courtesy tone
(indicates a remote is in the list of links)
linkunkeyct =
ct8 ; sent when a transmission
received over the link unkeys
;nolocallinkct =
0 ; Send unlinkedct instead if
another local node is connected to this node (hosted on
the same PC).
;connpgm =
yourconnectprogram ; Disabled. Execute a program
you specify on connect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being connected to us (them)
;discpgm =
yourdisconnectprogram ; Disabled. Execute a program
you specify on disconnect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being disconnected from us (them)
;lnkactenable =
0 ; Set to 1 to enable the link
activity timer. Applicable to standard nodes only.
;lnkacttime =
1800 ; Link activity timer time in
seconds.
;lnkactmacro =
*52 ; Function to execute when link
activity timer expires.
;lnkacttimerwarn
= 30seconds ; Message to play when the link
activity timer has 30 seconds left.
;remote_inact_timeout
= ; Specifies the amount of time without
keying from the link. Set to 0 to disable timeout. (15 *
60)
;remote_timeout
= ; Session time out for remote
base. Set to 0 to disable. (60 * 60)
;remote_timeout_warning_freq
= ; 30
;remote_timeout_warning
= ; (3 * 60)
;nounkeyct =
0 ; Set to a 1 to eliminate
courtesy tones and associated delays.
holdofftelem =
0 ; Hold off all telemetry when
signal is present on receiver or from connected nodes
; except when an ID needs to be done and there is a signal
coming from a connected node.
telemdefault =
0 ; 0 = telemetry output off
; 1 = telemetry output on (default = 1)
; 2 = timed telemetry output on command execution and for
a short time thereafter.
telemdynamic =
1 ; 0 = disallow users to change
the local telemetry setting with a COP command,
; 1 = Allow users to change the setting with a COP
command. (default = 1)
;beaconing =
0 ; Send ID regardless of
repeater activity (Required in the UK, but probably
illegal in the US)
parrotmode =
0 ; 0 = Parrot Off (default = 0)
; 1 = Parrot On Command
; 2 = Parrot Always
; 3 = Parrot Once by Command
parrottime =
1000 ; Set the amount of time in
milliseconds
; to wait before parroting what was received
;rxnotch=1065,40
; (Optional) Notch a particular frequency for a specified
; b/w. app_rpt must have been compiled with
; the notch option
startup_macro =
; nodenames =
/var/lib/asterisk/sounds/rpt/nodenames.callsign ; Point
to alternate nodename sound directory
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Need more
information on these
;extnodes =
extnodes-different ; section in extnodefile containing
dynamic node information (optional)
;extnodefile =
/foo/nodes ; Points to nodelist file containing
dynamic node info default = /var/lib/asterisk/rpt_extnodes
(optional)
;extnodefile2
= ; Is this a list of node files? Possible
a list of private nodes or a list of static IPs for known
nodes????
;nodenames =
/foo/names ; locaton of node sound files default =
/var/lib/asterisk/sounds/rpt/nodenames
;archivedir =
/tmp ; defines and enables activity recording
into specified directory (optional)
;monminblocks =
2048 ; Min 1K blocks to be left on partition
(will not save monitor output if disk too full)
;
; The tailmessagetime,tailsquashedtime, and
tailmessagelist need to be set
;
; to support tail messages. They can be omitted otherwise.
;tailmessagetime
= 300000 ; Play a tail message every 5 mins
;tailsquashedtime
= 30000 ; If squashed by another user,
;
; try again after 30 seconds
;tailmessagelist
= msg1,msg2 ; list of messages to be played for tail
message
; alt_functions
; ctgroup
;
dphone_functions
; idtime
; iobase
; iospeed
; locallist
; mars
Remote Base
; memory
; nobusyout
; nodes
; nolocallinkct
; notelemtx
; outxlat
; parrot
;
propagate_phonedtmf
; rptnode
; rptinactmacro
Macro to execute when inactivity timer expires
; rptinacttime
Inactivity timer time in seconds (0 seconds disables
feature)
; rxnotch
Optional Audio notch
;
simplexphonedelay
; tonemacro
; tonezone
; txlimits
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; *** Status
Reporting ***
; Comment the
following statpost line stop to reporting of the status of
your node to stats.allstarlink.org
statpost_url = http://stats.allstarlink.org/uhandler
; Status updates
[functions]
; Prefix
Functions
; *1
Disconnect Link
; *2
Monitor Link
; *3
Connect Link
; *4
Command Mode
; *5
Macros
; *6
User Functions
; *7
Connection Status/Functions
; *8
User Functions
; *9
User Functions
; *0
User Functions
; *A
User Functions
; *B
User Functions
; *C
User Functions
; *D
User Functions
; Mandatory
Command Codes
; http://docs.allstarlink.org/drupal/node/91
1 =
ilink,1 ; Disconnect specified link
2 =
ilink,2 ; Connect specified link -- monitor
only
3 =
ilink,3 ; Connect specified link -- tranceive
4 =
ilink,4 ; Enter command mode on specified link
70 =
ilink,5 ; System status
99 =
cop,6 ; PTT (phone mode only)
; End Mandatory
Command Codes
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Macro Commands
5 = macro
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Autopatch
Commands
; Note, This may
be a good place for other 2 digit frequently used commands
61 =
autopatchup,noct = 1,farenddisconnect = 1,dialtime =
20000 ; Autopatch up
62 =
autopatchdn
; Autopatch down
; autopatchup can
optionally take comma delimited setting=value pairs:
; context =
string ; Override default context with
"string"
; dialtime =
ms ; Specify the max number of
milliseconds between phone number digits (1000
milliseconds = 1 second)
;
farenddisconnect = 1 ; Automatically disconnect
when called party hangs up
; noct =
1 ; Don't send repeater courtesy tone
during autopatch calls
; quiet =
1 ; Don't send dial tone, or connect
messages. Do not send patch down message when called party
hangs up
; Example:
123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Status Commands
; 1 - Force ID
(global)
; 2 - Give Time
of Day (global)
; 3 - Give
software Version (global)
; 4 - Give GPS
location info
; 5 - Last (dtmf)
user
; 11 - Force ID
(local only)
; 12 - Give Time
of Day (local only)
721 =
status,1 ; Force ID (global)
722 =
status,2 ; Give Time of Day (global)
723 =
status,3 ; Give software Version (global)
724 =
status,4 ; Give GPS location info
725 =
status,5 ; Last (dtmf) user
711 =
status,11 ; Force ID (local only)
712 =
status,12 ; Give Time of Day (local only)
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Link Commands
; 1 - Disconnect
specified link
; 2 - Connect
specified link -- monitor only
; 3 - Connect
specified link -- tranceive
; 4 - Enter
command mode on specified link
; 5 - System
status
; 6 - Disconnect
all links
; 7 - Last Node
to Key Up
; 8 - Connect
specified link -- local monitor only
; 9 - Send Text
Message (9,<destnodeno or 0 (for all)>,Message Text,
etc.
; 10 - Disconnect
all RANGER links (except permalinks)
; 11 - Disconnect
a previously permanently connected link
; 12 -
Permanently connect specified link -- monitor only
; 13 -
Permanently connect specified link -- tranceive
; 15 - Full
system status (all nodes)
; 16 - Reconnect
links disconnected with "disconnect all links"
; 17 - MDC test
(for diag purposes)
; 18 -
Permanently Connect specified link -- local monitor only
; ilink commands
1 through 5 are defined in the Mandatory Command section
806 =
ilink,6 ; Disconnect all links
807 =
ilink,7 ; Last Node to Key Up
808 =
ilink,8 ; Connect specified link --
local monitor only
809 =
ilink,9,1999,"Testing" ; would send a text message to
node 1999 replace 1999 with 0 for all connected nodes
810 =
ilink,10 ; Disconnect all RANGER links
(except permalinks)
811 =
ilink,11 ; Disconnect a previously
permanently connected link
812 =
ilink,12 ; Permanently connect specified
link -- monitor only
813 =
ilink,13 ; Permanently connect specified
link -- tranceive
815 =
ilink,15 ; Full system status (all nodes)
816 =
ilink,16 ; Reconnect links disconnected
with "disconnect all links"
817 =
ilink,17 ; MDC test (for diag purposes)
818 = ilink
18 ; Permanently Connect specified link
-- local monitor only
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Control
operator (cop) functions. Change these to something other
than these codes listed below!
901 =
cop,1 �� ; System warm boot
902 =
cop,2 ; System enable
903 =
cop,3 ; System disable
904 =
cop,4 ; Test tone on/off
(toggle)
905 =
cop,5 ; Dump system variables
on console (debug use only)
907 =
cop,7 ; Time out timer enable
908 =
cop,8 ; Time out timer disable
909 =
cop,9 ; Autopatch enable
910 =
cop,10 ; Autopatch disable
911 =
cop,11 ; User linking functions
enable
912 =
cop,12 ; User linking functions
disable
913 =
cop,13 ; Query system control
state
914 =
cop,14 ; Set system control
state
915 = cop,15
; Scheduler enable
916 =
cop,16 ; Scheduler disable
917 =
cop,17 ; User functions enable
(time, id, etc)
918 =
cop,18 ; User functions disable
919 =
cop,19 ; Select alternate hang
time (althangtime)
920 =
cop,20 ; Select standard
hangtime (hangtime)
921 =
cop,21 ; Enable Parrot Mode
922 =
cop,22 ; Disable Parrot Mode
923 =
cop,23 ; Birdbath (Current
Parrot Cleanup/Flush)
924 =
cop,24 ; Flush all telemetry
925 =
cop,25 ; Query last node
un-keyed
926 =
cop,26 ; Query all nodes
keyed/unkeyed
927 =
cop,27 ; Reset DAQ minimum on a
pin
928 =
cop,28 ; Reset DAQ maximum on a
pin
930 =
cop,30 ; Recall Memory Setting
in Attached Xcvr
931 =
cop,31 ; Channel Selector for
Parallel Programmed Xcvr
932 =
cop,32 ; Touchtone pad test:
command + Digit string + # to playback all digits pressed
933 =
cop,33 ; Local Telemetry Output
Enable
934 =
cop,34 ; Local Telemetry Output
Disable
935 =
cop,35 ; Local Telemetry Output
on Demand
936 =
cop,36 ; Foreign Link Local
Output Path Enable
937 =
cop,37 ; Foreign Link Local
Output Path Disable
938 =
cop,38 ; Foreign Link Local
Output Path Follows Local Telemetry
939 =
cop,39 ; Foreign Link Local
Output Path on Demand
942 =
cop,42 ; Echolink announce node
# only
943 =
cop,43 ; Echolink announce node
Callsign only
944 =
cop,44 ; Echolink announce node
# & Callsign
945 =
cop,45 ; Link Activity timer
enable
945 =
cop,46 ; Link Activity timer
disable
947 =
cop,47 ; Reset "Link Config
Changed" Flag
948 =
cop,48 ; Send Page Tone (Tone
specs separated by parenthesis)
949 =
cop,49 ; Disable incoming
connections (control state noice)
950 =
cop,50 ; Enable incoming
connections (control state noicd)
951 =
cop,51 ; Enable sleep mode
952 =
cop,52 ; Disable sleep mode
953 =
cop,53 ; Wake up from sleep
954 =
cop,54 ; Go to sleep
955 =
cop,55 ; Parrot Once if parrot
mode is disabled
956 =
cop,56 ; Rx CTCSS Enable
957 = cop,57
; Rx CTCSS Disable
958 =
cop.58 ; Tx CTCSS On Input only
Enable
959 =
cop,59 ; Tx CTCSS On Input only
Disable
960 =
cop,60 ; Send MDC-1200 Burst
(cop,60,type,UnitID[,DestID,SubCode])
; Type is 'I' for PttID, 'E' for Emergency, and 'C' for
Call
; (SelCall or Alert), or 'SX' for STS (ststus), where X is
0-F.
; DestID and subcode are only specified for the 'C' type
message.
; UnitID is the local systems UnitID. DestID is the
MDC1200 ID of
; the radio being called, and the subcodes are as follows:
; Subcode '8205' is Voice Selective Call for Spectra
('Call')
; Subcode '8015' is Voice Selective Call for Maxtrac
('SC') or
; Astro-Saber('Call')
; Subcode '810D' is Call Alert (like Maxtrac 'CA')
961 =
cop,61 ; Send Message to USB to
control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)
962 =
cop,62 ; Send Message to USB to
control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)
963 =
cop,63 ; Send pre-configred
APRSTT notification (cop,63,CALL[,OVERLAYCHR])
964 =
cop,64 ; Send pre-configred
APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])
965 =
cop,65 ; Send POCSAG page
(equipped channel types only)
[functions-remote]
0 =
remote,1 ; Retrieve Memory
1 =
remote,2 ; Set freq.
2 =
remote,3 ; Set tx PL tone
3 =
remote,4 ; Set rx PL tone
40 =
remote,100 ; Rx PL off
41 =
remote,101 ; Rx PL on
42 =
remote,102 ; Tx PL off
43 =
remote,103 ; Tx PL on
44 =
remote,104 ; Low Power
45 =
remote,105 ; Medium Power
46 =
remote,106 ; High Power
711 =
remote,107 ; Bump -20
714 =
remote,108 ; Bump -100
717 =
remote,109 ; Bump -500
713 =
remote,110 ; Bump +20
716 =
remote,111 ; Bump +100
719 =
remote,112 ; Bump +500
721 =
remote,113 ; Scan - slow
724 =
remote,114 ; Scan - quick
727 =
remote,115 ; Scan - fast
723 =
remote,116 ; Scan + slow
726 =
remote,117 ; Scan + quick
729 =
remote,118 ; Scan + fast
79 =
remote,119 ; Tune
51 =
remote,5 ; Long status query
52 =
remote,140 ; Short status query
67 =
remote,210 ; Send a *
69 =
remote,211 ; Send a #
;91 =
remote,99,CALLSIGN,LICENSETAG ; Remote base login.
; Define a different dtmf sequence for each user which is
; authorized to use the remote base to control access to
it.
; For examble 9139583=remote,99,WB6NIL,G would grant
access to
; the remote base and announce WB6NIL as being logged in.
; Another entry, 9148351=remote,99,WA6ZFT,E would grant
access to
; the remote base and
announce WA6ZFT as being logged in.
; When the remote base is disconnected from the
originating node, the
; user will be logged out. The LICENSETAG argument is used
to enforce
; tx frequency limits. See [txlimits] below.
85 =
cop,6 ; Remote base telephone
key
[telemetry]
; Telemetry
entries can be shared across all repeaters, or defined for
each repeater.
; Can be a tone
sequence, morse string, or a file
;
; |t - Tone
escape sequence
;
; Tone sequences
consist of 1 or more 4-tuple entries (freq1, freq2,
duration, amplitude)
; Single
frequencies are created by setting freq1 or freq2 to zero.
;
; |m - Morse
escape sequence
;
; Sends Morse
code at the telemetry amplitude and telemetry frequency as
defined in the
; [morse]
section.
;
; Follow with an
alphanumeric string
;
; |i - Morse ID
escape sequence
;
; Sends Morse
code at the ID amplitude and ID frequency as defined in
the
; [morse]
section.
;
;
path/to/sound/file/without/extension
;
; Send the sound
if in place of a constructed tone. Do not include the file
extension
; Example: ct8 =
rpt/bloop
; Example:
idrecording = rpt/nodenames/1999
ct1 =
|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2 =
|t(660,880,150,2048)
ct3 =
|t(440,0,150,4096)
ct4 =
|t(550,0,150,2048)
ct5 =
|t(660,0,150,2048)
ct6 =
|t(880,0,150,2048)
ct7 =
|t(660,440,150,2048)
ct8 =
|t(700,1100,150,2048)
ranger =
|t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)
remotemon =
|t(1209,0,50,2048) ;
local courtesy tone when receive only
remotetx =
|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ;
local courtesy tone when linked Trancieve mode
cmdmode =
|t(900,903,200,2048)
functcomplete =
|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
remcomplete =
|t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)
pfxtone =
|t(350,440,30000,3072)
patchup =
rpt/callproceeding
patchdown =
rpt/callterminated
; As far as what
the numbers mean,
;
(000,000,010,000)
; | | |
|-------amplitude
; | |
|-------------duration
; |
|-------------------Tone 2
;
|-------------------------Tone 1
; So, with
0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0
Amplitude.
; Use it for a
delay. Fine tuning for how long before telemetry is sent,
in conjunction with the telemdelay parameter)
; The numbers,
like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay,
amplitude of 2048.
; Morse code
parameters, these are common to all repeaters.
[morse]
speed =
20 ; Approximate speed in WPM
frequency =
800 ; Morse Telemetry Frequency
amplitude =
4096 ; Morse Telemetry Amplitude
idfrequency =
1065 ; Morse ID Frequency
idamplitude =
1024 ; Morse ID Amplitude
;
; This section
allows wait times for telemetry events to be adjusted
; A section for
wait times can be defined for every repeater
;
[wait-times]
telemwait =
2000 ; Time to wait before sending
most telemetry
idwait =
500 ; Time to wait before
starting ID
unkeywait =
2000 ; Time to wait after unkey
before sending CT's and link telemetry
calltermwait =
2000 ; Time to wait before announcing
"call terminated"
;
; This is where
you define your nodes which cam be connected to.
;
[nodes]
; Note, if you
are using automatic update for allstar link nodes,
; no allstar link
nodes should be defined here. Only place a definition
; for your local
nodes, and private (off of allstar link) nodes here.
460310 = radio@....0.1:4569/460310,NONE
; This must be changed to your node number
; and iax port number if not the default
; Memories for
remote bases
[memory]
;00 =
146.580,100.0,m
;01 =
147.030,103.5,m+t
;02 =
147.240,103.5,m+t
;03 =
147.765,79.7,m-t
;04 =
146.460,100.0,m
;05 =
146.550,100.0,m
; Place command
macros here
[macro]
;1 = *32011#
;2 =
*12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#
;3 =
*32001*32011*32050*32030*32060#
; Data
Acquisition configuration
;[daq-list]
;device =
device_name1
;device =
device_name2
;Where:
device_name1 and device_name2 are stanzas you define in
this file
;device =
daq-cham-1
; Device name
;[daq-cham-1]
; Defined in [daq-list]
;hwtype =
uchameleon ; DAQ hardware type
;devnode =
/dev/ttyUSB0 ; DAQ device node (if
required)
;1 =
inadc ; Pin definition for an
ADC channel
;2 = inadc
;3 = inadc
;4 = inadc
;5 = inadc
;6 = inadc
;7 = inadc
;8 = inadc
;9 =
inp ; Pin definition for an
input with a weak pullup resistor
;10 = inp
;11 = inp
;12 = inp
;13 =
in ; Pin definition for an
input without a weak pullup resistor
;14 =
out ; Pin definition for an
output
;15 = out
;16 = out
;17 = out
;18 = out
;[meter-faces]
;face =
scale(scalepre,scalediv,scalepost),word/?,...
;
; scalepre =
offset to add before dividing with scalediv
; scalediv = full
scale/number of whole units (e.g. 256/20 or 12.8 for 20
volts).
; scalepost =
offset to add after dividing with scalediv
;
;face =
range(X-Y:word,X2-Y2:word,...),word/?,...
;face =
bit(low-word,high-word),word/?,...
;
; word/? is
either a word in /var/lib/asterisk/sounds or one of its
subdirectories,
; or a question
mark which is a placeholder for the measured value.
;
;
; Battery voltage
0-20 volts
;batvolts =
scale(0,12.8,0),rpt/thevoltageis,?,ha/volts
; 4 quadrant wind
direction
;winddir =
range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?
; LM34
temperature sensor with 130 deg. F full scale
;lm34f =
scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit
; Status poll
(non alarmed)
;light =
bit(ha/off,ha/on),ha/light,?
;[alarms]
;
;tag =
device,pin,node,ignorefirst,func-low,func-hi
;
;tag = a unique
name for the alarm
;device = daq
device to poll
;pin = the device
pin to be monitored
;ignorefirstalarm
= set to 1 to throwaway first alarm event, or 0 to report
it
;node = the node
number to execute the function on
;func-low = the
DTMF function to execute on a high to low transition
;func-high = the
DTMF function to execute on a low to high transition
;
; a '-' as a
function name is shorthand for no-operation
;
;door =
daq-cham-1,9,1,2017,*7,-
;pwrfail =
daq-cham-1,10,0,2017,*911111,-
;
; Control states
; Allow several
control operator functions to be changed at once using one
command (good for scheduling)
;
;[controlstates]
;statenum =
copcmd,[copcmd]...
;0 =
rptena,lnkena,apena,totena,ufena,noicd ; Normal operation
;1 =
rptena,lnkena,apdis,totdis,ufena,noice ; Net and news
operation
;2 =
rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only
operation
; Scheduler -
execute a macro at a given time
[schedule]
;dtmf_function =
m h dom mon dow ; ala cron, star is implied
;2 = 00 00 * *
* ; at midnight, execute macro 2.
#includeifexists
custom/rpt.conf
Analog_Bridge.ini
; Analog_Bridge
configuration file.
; This file
should be placed in either /etc or it can be
; supplied as a
path on the Analog_Bridge command line.
; The best way to
think of this file is that there are two main sections,
the USRP (analog audio) and
; AMBE_AUDIO
(compressed audio). Analog_Bridge will take everything
sent to the USRP port and
; encode it for
transmission on the AMBE_AUDIO port. The encoder will use
the format defined in ambeMode.
; As you might
expect, the reverse direction is defined too.
; Analog_Bridge
supports include files. More on this later...
include =
dvsm.macro
; include =
asl.macro
; General Section
describes settings for Analog_Bridge itself.
[GENERAL]
logLevel =
2 ; Show messages and above
0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning,
5=Error, 6=Fatal
; Metadata
management
exportMetadata =
true ; Export metadata to USRP partner
(transcode setups require this)
transferRootDir =
/tmp ; Export database files to USRP
partner
subscriberFile =
/var/lib/dvswitch/subscriber_ids.csv ; DMR ID to
callsign lookup data
; General vocoder
setup information
decoderFallBack =
true ; Allow software AMBE decoding if a
hardware decoder is not found
useEmulator =
false ; Use the MD380 AMBE emulator
for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress =
127.0.0.1:2470 ; IP address and port of the md380
server
pcmPort =
2222 ; UDP port to send to the
WebProxy
; Information for
xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address =
127.0.0.1 ; IP address of xx_Bridge
txPort =
31103 ; Transmit TLV frames to
partner on this port
rxPort =
31100 ; Listen for TLV frames
from partner on this port
ambeMode =
DMR ; DMR, DMR_IPSC, DSTAR, NXDN,
P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS =
2500 ; Analog -> Digital Minimum
time in MS for hang delay (0-10000)
; The metadata
below is used when ASL is the source since it does not
have any concept of digital modes
gatewayDmrId =
1112721 ; ID to use when transmitting
from Analog_Bridge 7 digit ID
repeaterID =
111272123 ; ID of source repeater 7 digit
ID plus 2 digit SSID
txTg =
31676 ; TG to use for all
frames sent from Analog_Bridge -> xx_Bridge
txTs =
2 ; Slot to use for frames
sent from Analog_Bridge -> xx_Bridge
colorCode =
1 ; Color Code to assign DMR
frames
; Information for
USRP channel driver. This interface uses PCM to transfer
audio information
; There are two
typical configurations, ASL and Transcode. ASL
(AllstarLink) is for analog clients connected
; to a digital
network. Transcode is when Analog_Bridge actually points
its PCM interfaces back at itself,
; causing a TLV
<-- (pcm <--> pcm) --> TLV type of
architecture.
; When using
ASL, this matches the rpt.conf ASL file with a setting
like:
; rxchannel =
usrp/127.0.0.1:34001:32001
; When
Transcoding, make two ini files and set txPort equal to
the other instance rxPort (crossover). Launch
; each instance
with its own ini file.
[USRP]
address =
127.0.0.1 ; IP address of USRP partner
(Allstar/Asterisk or another Analog_Bridge)
txPort =
32001 ; Transmit USRP frames on
this port
rxPort =
34001 ; Listen for USRP frames on
this port
usrpAudio =
AUDIO_UNITY ; Digital -> Analog
(AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)
usrpGain =
1.10 ; Gain factor when usrpAudio
= AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
usrpAGC =
-20,10,100 ; Set the agc threshold
(db), slope (db) and decay (ms)
tlvAudio =
AUDIO_UNITY ; Analog -> Digital
(AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain =
0.35 ; Gain factor when tlvAudio
= AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY)
[MACROS]
; Where the
macros are
; xxxx=yyyy
; xxxx is the
dial string to match
; yyyy is the
command line to execute
; xxxx must be
preceded by a *
; xxxx can be any
string (alphanumeric)
; yyyy is the
command to execute
; yyyy will
replace xxxx in the dial string
; arguments
follow the macro name with a # delimiter
; For example
using macro "5678" above would look like:
; *5678#9876
; Which would
invoke:
; echo 9876
; Information for
DV3000 hardware decoder
; There are two
configuration modes: IP (AMBEServer) and serial (direct
connect hardware)
; Use top
server and port if using AMBEServer
; Use bottom
server/port and serial = true if using the DV3000u
(thumbdv)
; Did you run
AMBETest4.py before using this?
[DV3000]
address =
127.0.0.1 ; IP address of AMBEServer
rxPort =
2460 ; Port of AMBEServer
; address =
/dev/ttyUSB0 ; Device of DV3000U on this
machine
; baud =
460800 ; Baud rate of the dongle
(230400 or 460800)
; serial =
true ; Use serial=true f
|
|
|
toggle quoted messageShow quoted text
From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS Sent: Sunday, February 14, 2021 2:50 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] ASL<>AB Did you fix rpt.conf and did you then restart asterisk? On 2/14/21 2:46 PM, Steve Siesel [K4KSA] wrote: After restarting AB and Asterisk….also md3890-emu is running Still no Joy…Here is the latest start of Analog_bridge.log I: 2021-02-14 19:43:13.761 Analog_Bridge is starting M: 2021-02-14 19:43:13.762 Setting [MACROS] DMR -> /opt/MMDVM_Bridge/dvswitch.sh mode DMR M: 2021-02-14 19:43:13.762 Setting [MACROS] DSTAR -> /opt/MMDVM_Bridge/dvswitch.sh mode DSTAR M: 2021-02-14 19:43:13.762 Setting [MACROS] NXDN -> /opt/MMDVM_Bridge/dvswitch.sh mode NXDN M: 2021-02-14 19:43:13.762 Setting [MACROS] P25 -> /opt/MMDVM_Bridge/dvswitch.sh mode P25 M: 2021-02-14 19:43:13.762 Setting [MACROS] YSF -> /opt/MMDVM_Bridge/dvswitch.sh mode YSF M: 2021-02-14 19:43:13.762 Setting [MACROS] dbupdate -> /opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles M: 2021-02-14 19:43:13.764 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh M: 2021-02-14 19:43:13.765 Setting [] include -> dvsm.macro M: 2021-02-14 19:43:13.766 Setting [GENERAL] logLevel -> 2 M: 2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata -> true M: 2021-02-14 19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp M: 2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv M: 2021-02-14 19:43:13.768 Setting [GENERAL] decoderFallBack -> true M: 2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator -> false M: 2021-02-14 19:43:13.769 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470 M: 2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort -> 2222 M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1 M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103 M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100 M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500 M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721 M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1 M: 2021-02-14 19:43:13.773 Setting [USRP] address -> 127.0.0.1 M: 2021-02-14 19:43:13.773 Setting [USRP] txPort -> 32001 M: 2021-02-14 19:43:13.773 Setting [USRP] rxPort -> 34001 M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY M: 2021-02-14 19:43:13.774 Setting [USRP] usrpGain -> 1.10 M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100 M: 2021-02-14 19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY M: 2021-02-14 19:43:13.775 Setting [USRP] tlvGain -> 0.35 M: 2021-02-14 19:43:13.776 Setting [DV3000] address -> 127.0.0.1 M: 2021-02-14 19:43:13.776 Setting [DV3000] rxPort -> 2460 I: 2021-02-14 19:43:13.777 Open UDP listener on 127.0.0.1:31100 I: 2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001 M: 2021-02-14 19:43:13.777 Connecting to DV3000 hardware...... W: 2021-02-14 19:43:13.871 DV3000 did not reset at 127.0.0.1:2460 W: 2021-02-14 19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset failed) I: 2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850 I: 2021-02-14 19:43:16.073 Default extended metadata <K4KSA> W: 2021-02-14 19:43:16.073 Using software MBE decoder version 1.2.3 W: 2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE vocoder I: 2021-02-14 19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s) 32001 I: 2021-02-14 19:43:16.074 Sending PCM to clients at 127.0.0.1 on port 2222 I: 2021-02-14 19:43:16.074 Starting TLV --> Analog_Bridge (decoder) --> USRP thread I: 2021-02-14 19:43:16.075 Starting USRP --> Analog_Bridge (encoder) -> TLV thread You have 2 channel drivers uncommented:
rxchannel = dahdi/pseudo ; No radio (hub) <--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel = Pi/1 ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999 ; USBRadio (DSP)
; rxchannel = Dahdi/1 ; PCI Quad card
; rxchannel = Beagle/1 ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999 ; RTCM device On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote: Can you look at this as well….. I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that. Steve ; Your Repeater ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [460310] ; Change this to your assigned node number ; Must also be enabled in modules.conf ; Rx audio/signalling channel. Choose ONLY 1 per node stanza ; Enable the selected channel driver in modules.conf !!! rxchannel = dahdi/pseudo ; No radio (hub) ; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_1999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP ; rxchannel = Voter/1999 ; RTCM device duplex = 1 ; 0 = Half duplex with no telemetry tones or hang time. ; Special Case: Full duplex if linktolink is set to yes. ; This mode is preferred when interfacing with an external multiport repeater controller. ; Comment out idrecording and idtalkover to suppress IDs also ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio. ; This mode is preferred when interfacing a simplex node. ; 2 = Full Duplex with telemetry tones and hang time. ; This mode is preferred when interfacing a repeater. ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio. ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down. linktolink = no ; disables forcing physical half-duplex operation of main repeater while ; still keeping half-duplex semantics (optional) linkmongain = 0 ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received. ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db. ; If linkmongain set to a positive number monitored audio will increase by the set amount in db. ; The value of linkmongain is in db. The default value is 0 db. erxgain = -3 ; Echolink receive gain adjustment ; Note: Gain is in db-volts (20logVI/VO) etxgain = 3 ; Echolink transmit gain adjustment ; Note: Gain is in db-volts (20logVI/VO) ;eannmode = 1 ; 1 = Say only node number on echolink connects (default = 1) ; 2 = say phonetic call sign only on echolink connects ; 3 = say phonetic call sign and node number on echolink connects ;controlstates = controlstates ; system control state stanza scheduler = schedule ; scheduler stanza functions = functions ; Repeater Function stanza phone_functions = functions ; Phone Function stanza link_functions = functions ; Link Function stanza telemetry = telemetry ; Telemetry stanza morse = morse ; Morse stanza wait_times = wait-times ; Wait times stanza context = radio ; dialing context for phone callerid = "Repeater" <0000000000> ; callerid for phone calls accountcode = RADIO ; account code (optional) hangtime = 5000 ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms) althangtime = 4000 ; longer squelch tail totime = 180000 ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms) idrecording = |iWA4XYZ ; cording or morse string see http://ohnosec.org/drupal/node/87 idtalkover = |iWA4XYZ ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129 ; See Telemetry section Example: idrecording = rpt/nodenames/1999 idtime = 540000 ; id interval time (in ms) (optional) Default 5 minutes (300000 ms) politeid = 30000 ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000) unlinkedct = ct2 ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none) remotect = ct3 ; remote linked courtesy tone (indicates a remote is in the list of links) linkunkeyct = ct8 ; sent when a transmission received over the link unkeys ;nolocallinkct = 0 ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC). ;connpgm = yourconnectprogram ; Disabled. Execute a program you specify on connect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being connected to us (them) ;discpgm = yourdisconnectprogram ; Disabled. Execute a program you specify on disconnect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being disconnected from us (them) ;lnkactenable = 0 ; Set to 1 to enable the link activity timer. Applicable to standard nodes only. ;lnkacttime = 1800 ; Link activity timer time in seconds. ;lnkactmacro = *52 ; Function to execute when link activity timer expires. ;lnkacttimerwarn = 30seconds ; Message to play when the link activity timer has 30 seconds left. ;remote_inact_timeout = ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60) ;remote_timeout = ; Session time out for remote base. Set to 0 to disable. (60 * 60) ;remote_timeout_warning_freq = ; 30 ;remote_timeout_warning = ; (3 * 60) ;nounkeyct = 0 ; Set to a 1 to eliminate courtesy tones and associated delays. holdofftelem = 0 ; Hold off all telemetry when signal is present on receiver or from connected nodes ; except when an ID needs to be done and there is a signal coming from a connected node. telemdefault = 0 ; 0 = telemetry output off ; 1 = telemetry output on (default = 1) ; 2 = timed telemetry output on command execution and for a short time thereafter. telemdynamic = 1 ; 0 = disallow users to change the local telemetry setting with a COP command, ; 1 = Allow users to change the setting with a COP command. (default = 1) ;beaconing = 0 ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US) parrotmode = 0 ; 0 = Parrot Off (default = 0) ; 1 = Parrot On Command ; 2 = Parrot Always ; 3 = Parrot Once by Command parrottime = 1000 ; Set the amount of time in milliseconds ; to wait before parroting what was received ;rxnotch=1065,40 ; (Optional) Notch a particular frequency for a specified ; b/w. app_rpt must have been compiled with ; the notch option startup_macro = ; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign ; Point to alternate nodename sound directory ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Need more information on these ;extnodes = extnodes-different ; section in extnodefile containing dynamic node information (optional) ;extnodefile = /foo/nodes ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional) ;extnodefile2 = ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes???? ;nodenames = /foo/names ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames ;archivedir = /tmp ; defines and enables activity recording into specified directory (optional) ;monminblocks = 2048 ; Min 1K blocks to be left on partition (will not save monitor output if disk too full) ; ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set ; ; to support tail messages. They can be omitted otherwise. ;tailmessagetime = 300000 ; Play a tail message every 5 mins ;tailsquashedtime = 30000 ; If squashed by another user, ; ; try again after 30 seconds ;tailmessagelist = msg1,msg2 ; list of messages to be played for tail message ; alt_functions ; ctgroup ; dphone_functions ; idtime ; iobase ; iospeed ; locallist ; mars Remote Base ; memory ; nobusyout ; nodes ; nolocallinkct ; notelemtx ; outxlat ; parrot ; propagate_phonedtmf ; rptnode ; rptinactmacro Macro to execute when inactivity timer expires ; rptinacttime Inactivity timer time in seconds (0 seconds disables feature) ; rxnotch Optional Audio notch ; simplexphonedelay ; tonemacro ; tonezone ; txlimits ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; *** Status Reporting *** ; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org statpost_url = http://stats.allstarlink.org/uhandler ; Status updates [functions] ; Prefix Functions ; *1 Disconnect Link ; *2 Monitor Link ; *3 Connect Link ; *4 Command Mode ; *5 Macros ; *6 User Functions ; *7 Connection Status/Functions ; *8 User Functions ; *9 User Functions ; *0 User Functions ; *A User Functions ; *B User Functions ; *C User Functions ; *D User Functions ; Mandatory Command Codes ; http://docs.allstarlink.org/drupal/node/91 1 = ilink,1 ; Disconnect specified link 2 = ilink,2 ; Connect specified link -- monitor only 3 = ilink,3 ; Connect specified link -- tranceive 4 = ilink,4 ; Enter command mode on specified link 70 = ilink,5 ; System status 99 = cop,6 ; PTT (phone mode only) ; End Mandatory Command Codes ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Macro Commands 5 = macro ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Autopatch Commands ; Note, This may be a good place for other 2 digit frequently used commands 61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000 ; Autopatch up 62 = autopatchdn ; Autopatch down ; autopatchup can optionally take comma delimited setting=value pairs: ; context = string ; Override default context with "string" ; dialtime = ms ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second) ; farenddisconnect = 1 ; Automatically disconnect when called party hangs up ; noct = 1 ; Don't send repeater courtesy tone during autopatch calls ; quiet = 1 ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Status Commands ; 1 - Force ID (global) ; 2 - Give Time of Day (global) ; 3 - Give software Version (global) ; 4 - Give GPS location info ; 5 - Last (dtmf) user ; 11 - Force ID (local only) ; 12 - Give Time of Day (local only) 721 = status,1 ; Force ID (global) 722 = status,2 ; Give Time of Day (global) 723 = status,3 ; Give software Version (global) 724 = status,4 ; Give GPS location info 725 = status,5 ; Last (dtmf) user 711 = status,11 ; Force ID (local only) 712 = status,12 ; Give Time of Day (local only) ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Link Commands ; 1 - Disconnect specified link ; 2 - Connect specified link -- monitor only ; 3 - Connect specified link -- tranceive ; 4 - Enter command mode on specified link ; 5 - System status ; 6 - Disconnect all links ; 7 - Last Node to Key Up ; 8 - Connect specified link -- local monitor only ; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc. ; 10 - Disconnect all RANGER links (except permalinks) ; 11 - Disconnect a previously permanently connected link ; 12 - Permanently connect specified link -- monitor only ; 13 - Permanently connect specified link -- tranceive ; 15 - Full system status (all nodes) ; 16 - Reconnect links disconnected with "disconnect all links" ; 17 - MDC test (for diag purposes) ; 18 - Permanently Connect specified link -- local monitor only ; ilink commands 1 through 5 are defined in the Mandatory Command section 806 = ilink,6 ; Disconnect all links 807 = ilink,7 ; Last Node to Key Up 808 = ilink,8 ; Connect specified link -- local monitor only 809 = ilink,9,1999,"Testing" ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes 810 = ilink,10 ; Disconnect all RANGER links (except permalinks) 811 = ilink,11 ; Disconnect a previously permanently connected link 812 = ilink,12 ; Permanently connect specified link -- monitor only 813 = ilink,13 ; Permanently connect specified link -- tranceive 815 = ilink,15 ; Full system status (all nodes) 816 = ilink,16 ; Reconnect links disconnected with "disconnect all links" 817 = ilink,17 ; MDC test (for diag purposes) 818 = ilink 18 ; Permanently Connect specified link -- local monitor only ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Control operator (cop) functions. Change these to something other than these codes listed below! 901 = cop,1 �� ; System warm boot 902 = cop,2 ; System enable 903 = cop,3 ; System disable 904 = cop,4 ; Test tone on/off (toggle) 905 = cop,5 ; Dump system variables on console (debug use only) 907 = cop,7 ; Time out timer enable 908 = cop,8 ; Time out timer disable 909 = cop,9 ; Autopatch enable 910 = cop,10 ; Autopatch disable 911 = cop,11 ; User linking functions enable 912 = cop,12 ; User linking functions disable 913 = cop,13 ; Query system control state 914 = cop,14 ; Set system control state 915 = cop,15 ; Scheduler enable 916 = cop,16 ; Scheduler disable 917 = cop,17 ; User functions enable (time, id, etc) 918 = cop,18 ; User functions disable 919 = cop,19 ; Select alternate hang time (althangtime) 920 = cop,20 ; Select standard hangtime (hangtime) 921 = cop,21 ; Enable Parrot Mode 922 = cop,22 ; Disable Parrot Mode 923 = cop,23 ; Birdbath (Current Parrot Cleanup/Flush) 924 = cop,24 ; Flush all telemetry 925 = cop,25 ; Query last node un-keyed 926 = cop,26 ; Query all nodes keyed/unkeyed 927 = cop,27 ; Reset DAQ minimum on a pin 928 = cop,28 ; Reset DAQ maximum on a pin 930 = cop,30 ; Recall Memory Setting in Attached Xcvr 931 = cop,31 ; Channel Selector for Parallel Programmed Xcvr 932 = cop,32 ; Touchtone pad test: command + Digit string + # to playback all digits pressed 933 = cop,33 ; Local Telemetry Output Enable 934 = cop,34 ; Local Telemetry Output Disable 935 = cop,35 ; Local Telemetry Output on Demand 936 = cop,36 ; Foreign Link Local Output Path Enable 937 = cop,37 ; Foreign Link Local Output Path Disable 938 = cop,38 ; Foreign Link Local Output Path Follows Local Telemetry 939 = cop,39 ; Foreign Link Local Output Path on Demand 942 = cop,42 ; Echolink announce node # only 943 = cop,43 ; Echolink announce node Callsign only 944 = cop,44 ; Echolink announce node # & Callsign 945 = cop,45 ; Link Activity timer enable 945 = cop,46 ; Link Activity timer disable 947 = cop,47 ; Reset "Link Config Changed" Flag 948 = cop,48 ; Send Page Tone (Tone specs separated by parenthesis) 949 = cop,49 ; Disable incoming connections (control state noice) 950 = cop,50 ; Enable incoming connections (control state noicd) 951 = cop,51 ; Enable sleep mode 952 = cop,52 ; Disable sleep mode 953 = cop,53 ; Wake up from sleep 954 = cop,54 ; Go to sleep 955 = cop,55 ; Parrot Once if parrot mode is disabled 956 = cop,56 ; Rx CTCSS Enable 957 = cop,57 ; Rx CTCSS Disable 958 = cop.58 ; Tx CTCSS On Input only Enable 959 = cop,59 ; Tx CTCSS On Input only Disable 960 = cop,60 ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode]) ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F. ; DestID and subcode are only specified for the 'C' type message. ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of ; the radio being called, and the subcodes are as follows: ; Subcode '8205' is Voice Selective Call for Spectra ('Call') ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or ; Astro-Saber('Call') ; Subcode '810D' is Call Alert (like Maxtrac 'CA') 961 = cop,61 ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....) 962 = cop,62 ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....) 963 = cop,63 ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR]) 964 = cop,64 ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR]) 965 = cop,65 ; Send POCSAG page (equipped channel types only) [functions-remote] 0 = remote,1 ; Retrieve Memory 1 = remote,2 ; Set freq. 2 = remote,3 ; Set tx PL tone 3 = remote,4 ; Set rx PL tone 40 = remote,100 ; Rx PL off 41 = remote,101 ; Rx PL on 42 = remote,102 ; Tx PL off 43 = remote,103 ; Tx PL on 44 = remote,104 ; Low Power 45 = remote,105 ; Medium Power 46 = remote,106 ; High Power 711 = remote,107 ; Bump -20 714 = remote,108 ; Bump -100 717 = remote,109 ; Bump -500 713 = remote,110 ; Bump +20 716 = remote,111 ; Bump +100 719 = remote,112 ; Bump +500 721 = remote,113 ; Scan - slow 724 = remote,114 ; Scan - quick 727 = remote,115 ; Scan - fast 723 = remote,116 ; Scan + slow 726 = remote,117 ; Scan + quick 729 = remote,118 ; Scan + fast 79 = remote,119 ; Tune 51 = remote,5 ; Long status query 52 = remote,140 ; Short status query 67 = remote,210 ; Send a * 69 = remote,211 ; Send a # ;91 = remote,99,CALLSIGN,LICENSETAG ; Remote base login. ; Define a different dtmf sequence for each user which is ; authorized to use the remote base to control access to it. ; For examble 9139583=remote,99,WB6NIL,G would grant access to ; the remote base and announce WB6NIL as being logged in. ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to ; the remote base and announce WA6ZFT as being logged in. ; When the remote base is disconnected from the originating node, the ; user will be logged out. The LICENSETAG argument is used to enforce ; tx frequency limits. See [txlimits] below. 85 = cop,6 ; Remote base telephone key [telemetry] ; Telemetry entries can be shared across all repeaters, or defined for each repeater. ; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape sequence ; ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) ; Single frequencies are created by setting freq1 or freq2 to zero. ; ; |m - Morse escape sequence ; ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ; ; |i - Morse ID escape sequence ; ; Sends Morse code at the ID amplitude and ID frequency as defined in the ; [morse] section. ; ; path/to/sound/file/without/extension ; ; Send the sound if in place of a constructed tone. Do not include the file extension ; Example: ct8 = rpt/bloop ; Example: idrecording = rpt/nodenames/1999 ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2 = |t(660,880,150,2048) ct3 = |t(440,0,150,4096) ct4 = |t(550,0,150,2048) ct5 = |t(660,0,150,2048) ct6 = |t(880,0,150,2048) ct7 = |t(660,440,150,2048) ct8 = |t(700,1100,150,2048) ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0) remotemon = |t(1209,0,50,2048) ; local courtesy tone when receive only remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local courtesy tone when linked Trancieve mode cmdmode = |t(900,903,200,2048) functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048) pfxtone = |t(350,440,30000,3072) patchup = rpt/callproceeding patchdown = rpt/callterminated ; As far as what the numbers mean, ; (000,000,010,000) ; | | | |-------amplitude ; | | |-------------duration ; | |-------------------Tone 2 ; |-------------------------Tone 1 ; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude. ; Use it for a delay. Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter) ; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048. ; Morse code parameters, these are common to all repeaters. [morse] speed = 20 ; Approximate speed in WPM frequency = 800 ; Morse Telemetry Frequency amplitude = 4096 ; Morse Telemetry Amplitude idfrequency = 1065 ; Morse ID Frequency idamplitude = 1024 ; Morse ID Amplitude ; ; This section allows wait times for telemetry events to be adjusted ; A section for wait times can be defined for every repeater ; [wait-times] telemwait = 2000 ; Time to wait before sending most telemetry idwait = 500 ; Time to wait before starting ID unkeywait = 2000 ; Time to wait after unkey before sending CT's and link telemetry calltermwait = 2000 ; Time to wait before announcing "call terminated" ; ; This is where you define your nodes which cam be connected to. ; [nodes] ; Note, if you are using automatic update for allstar link nodes, ; no allstar link nodes should be defined here. Only place a definition ; for your local nodes, and private (off of allstar link) nodes here. 460310 = radio@....0.1:4569/460310,NONE ; This must be changed to your node number ; and iax port number if not the default ; Memories for remote bases [memory] ;00 = 146.580,100.0,m ;01 = 147.030,103.5,m+t ;02 = 147.240,103.5,m+t ;03 = 147.765,79.7,m-t ;04 = 146.460,100.0,m ;05 = 146.550,100.0,m ; Place command macros here [macro] ;1 = *32011# ;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030# ;3 = *32001*32011*32050*32030*32060# ; Data Acquisition configuration ;[daq-list] ;device = device_name1 ;device = device_name2 ;Where: device_name1 and device_name2 are stanzas you define in this file ;device = daq-cham-1 ; Device name ;[daq-cham-1] ; Defined in [daq-list] ;hwtype = uchameleon ; DAQ hardware type ;devnode = /dev/ttyUSB0 ; DAQ device node (if required) ;1 = inadc ; Pin definition for an ADC channel ;2 = inadc ;3 = inadc ;4 = inadc ;5 = inadc ;6 = inadc ;7 = inadc ;8 = inadc ;9 = inp ; Pin definition for an input with a weak pullup resistor ;10 = inp ;11 = inp ;12 = inp ;13 = in ; Pin definition for an input without a weak pullup resistor ;14 = out ; Pin definition for an output ;15 = out ;16 = out ;17 = out ;18 = out ;[meter-faces] ;face = scale(scalepre,scalediv,scalepost),word/?,... ; ; scalepre = offset to add before dividing with scalediv ; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts). ; scalepost = offset to add after dividing with scalediv ; ;face = range(X-Y:word,X2-Y2:word,...),word/?,... ;face = bit(low-word,high-word),word/?,... ; ; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories, ; or a question mark which is a placeholder for the measured value. ; ; ; Battery voltage 0-20 volts ;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts ; 4 quadrant wind direction ;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,? ; LM34 temperature sensor with 130 deg. F full scale ;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit ; Status poll (non alarmed) ;light = bit(ha/off,ha/on),ha/light,? ;[alarms] ; ;tag = device,pin,node,ignorefirst,func-low,func-hi ; ;tag = a unique name for the alarm ;device = daq device to poll ;pin = the device pin to be monitored ;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it ;node = the node number to execute the function on ;func-low = the DTMF function to execute on a high to low transition ;func-high = the DTMF function to execute on a low to high transition ; ; a '-' as a function name is shorthand for no-operation ; ;door = daq-cham-1,9,1,2017,*7,- ;pwrfail = daq-cham-1,10,0,2017,*911111,- ; ; Control states ; Allow several control operator functions to be changed at once using one command (good for scheduling) ; ;[controlstates] ;statenum = copcmd,[copcmd]... ;0 = rptena,lnkena,apena,totena,ufena,noicd ; Normal operation ;1 = rptena,lnkena,apdis,totdis,ufena,noice ; Net and news operation ;2 = rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only operation ; Scheduler - execute a macro at a given time [schedule] ;dtmf_function = m h dom mon dow ; ala cron, star is implied ;2 = 00 00 * * * ; at midnight, execute macro 2. #includeifexists custom/rpt.conf Analog_Bridge.ini ; Analog_Bridge configuration file. ; This file should be placed in either /etc or it can be ; supplied as a path on the Analog_Bridge command line. ; The best way to think of this file is that there are two main sections, the USRP (analog audio) and ; AMBE_AUDIO (compressed audio). Analog_Bridge will take everything sent to the USRP port and ; encode it for transmission on the AMBE_AUDIO port. The encoder will use the format defined in ambeMode. ; As you might expect, the reverse direction is defined too. ; Analog_Bridge supports include files. More on this later... include = dvsm.macro ; include = asl.macro ; General Section describes settings for Analog_Bridge itself. [GENERAL] logLevel = 2 ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal ; Metadata management exportMetadata = true ; Export metadata to USRP partner (transcode setups require this) transferRootDir = /tmp ; Export database files to USRP partner subscriberFile = /var/lib/dvswitch/subscriber_ids.csv ; DMR ID to callsign lookup data ; General vocoder setup information decoderFallBack = true ; Allow software AMBE decoding if a hardware decoder is not found useEmulator = false ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN) emulatorAddress = 127.0.0.1:2470 ; IP address and port of the md380 server pcmPort = 2222 ; UDP port to send to the WebProxy ; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC) [AMBE_AUDIO] address = 127.0.0.1 ; IP address of xx_Bridge txPort = 31103 ; Transmit TLV frames to partner on this port rxPort = 31100 ; Listen for TLV frames from partner on this port ambeMode = DMR ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format) minTxTimeMS = 2500 ; Analog -> Digital Minimum time in MS for hang delay (0-10000) ; The metadata below is used when ASL is the source since it does not have any concept of digital modes gatewayDmrId = 1112721 ; ID to use when transmitting from Analog_Bridge 7 digit ID repeaterID = 111272123 ; ID of source repeater 7 digit ID plus 2 digit SSID txTg = 31676 ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge txTs = 2 ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge colorCode = 1 ; Color Code to assign DMR frames ; Information for USRP channel driver. This interface uses PCM to transfer audio information ; There are two typical configurations, ASL and Transcode. ASL (AllstarLink) is for analog clients connected ; to a digital network. Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, ; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture. ; When using ASL, this matches the rpt.conf ASL file with a setting like: ; rxchannel = usrp/127.0.0.1:34001:32001 ; When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover). Launch ; each instance with its own ini file. [USRP] address = 127.0.0.1 ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge) txPort = 32001 ; Transmit USRP frames on this port rxPort = 34001 ; Listen for USRP frames on this port usrpAudio = AUDIO_UNITY ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC) usrpGain = 1.10 ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY) usrpAGC = -20,10,100 ; Set the agc threshold (db), slope (db) and decay (ms) tlvAudio = AUDIO_UNITY ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) tlvGain = 0.35 ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY) [MACROS] ; Where the macros are ; xxxx=yyyy ; xxxx is the dial string to match ; yyyy is the command line to execute ; xxxx must be preceded by a * ; xxxx can be any string (alphanumeric) ; yyyy is the command to execute ; yyyy will replace xxxx in the dial string ; arguments follow the macro name with a # delimiter ; For example using macro "5678" above would look like: ; *5678#9876 ; Which would invoke: ; echo 9876 ; Information for DV3000 hardware decoder ; There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware) ; Use top server and port if using AMBEServer ; Use bottom server/port and serial = true if using the DV3000u (thumbdv) ; Did you run AMBETest4.py before using this? [DV3000] address = 127.0.0.1 ; IP address of AMBEServer rxPort = 2460 ; Port of AMBEServer ; address = /dev/ttyUSB0 ; Device of DV3000U on this machine ; baud = 460800 ; Baud rate of the dongle (230400 or 460800) ; serial = true ; Use serial=true f
|
|
|
Steve N4IRS
Is chan_usrp enabled in modules.conf?
toggle quoted messageShow quoted text
On 2/14/21 2:50 PM, Steve Siesel
[K4KSA] wrote:
Yes…..
Did you fix
rpt.conf and did you then restart asterisk?
On 2/14/21 2:46 PM, Steve Siesel [K4KSA]
wrote:
After
restarting AB and Asterisk….also md3890-emu is running
Still no
Joy…Here is the latest start of Analog_bridge.log
I: 2021-02-14
19:43:13.761 Analog_Bridge is starting
M: 2021-02-14
19:43:13.762 Setting [MACROS] DMR ->
/opt/MMDVM_Bridge/dvswitch.sh mode DMR
M: 2021-02-14
19:43:13.762 Setting [MACROS] DSTAR ->
/opt/MMDVM_Bridge/dvswitch.sh mode DSTAR
M: 2021-02-14
19:43:13.762 Setting [MACROS] NXDN ->
/opt/MMDVM_Bridge/dvswitch.sh mode NXDN
M: 2021-02-14
19:43:13.762 Setting [MACROS] P25 ->
/opt/MMDVM_Bridge/dvswitch.sh mode P25
M: 2021-02-14
19:43:13.762 Setting [MACROS] YSF ->
/opt/MMDVM_Bridge/dvswitch.sh mode YSF
M: 2021-02-14
19:43:13.762 Setting [MACROS] dbupdate ->
/opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles
M: 2021-02-14
19:43:13.764 Setting [MACROS] 9876 ->
/opt/Analog_Bridge/parrot.sh
M: 2021-02-14
19:43:13.765 Setting [] include -> dvsm.macro
M: 2021-02-14
19:43:13.766 Setting [GENERAL] logLevel -> 2
M: 2021-02-14
19:43:13.766 Setting [GENERAL] exportMetadata -> true
M: 2021-02-14
19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp
M: 2021-02-14
19:43:13.767 Setting [GENERAL] subscriberFile ->
/var/lib/dvswitch/subscriber_ids.csv
M: 2021-02-14
19:43:13.768 Setting [GENERAL] decoderFallBack -> true
M: 2021-02-14
19:43:13.768 Setting [GENERAL] useEmulator -> false
M: 2021-02-14
19:43:13.769 Setting [GENERAL] emulatorAddress ->
127.0.0.1:2470
M: 2021-02-14
19:43:13.769 Setting [GENERAL] pcmPort -> 2222
M: 2021-02-14
19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1
M: 2021-02-14
19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103
M: 2021-02-14
19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100
M: 2021-02-14
19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR
M: 2021-02-14
19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500
M: 2021-02-14
19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId ->
1112721
M: 2021-02-14
19:43:13.771 Setting [AMBE_AUDIO] repeaterID ->
111272123
M: 2021-02-14
19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676
M: 2021-02-14
19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2
M: 2021-02-14
19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1
M: 2021-02-14
19:43:13.773 Setting [USRP] address -> 127.0.0.1
M: 2021-02-14
19:43:13.773 Setting [USRP] txPort -> 32001
M: 2021-02-14
19:43:13.773 Setting [USRP] rxPort -> 34001
M: 2021-02-14
19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY
M: 2021-02-14
19:43:13.774 Setting [USRP] usrpGain -> 1.10
M: 2021-02-14
19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100
M: 2021-02-14
19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY
M: 2021-02-14
19:43:13.775 Setting [USRP] tlvGain -> 0.35
M: 2021-02-14
19:43:13.776 Setting [DV3000] address -> 127.0.0.1
M: 2021-02-14
19:43:13.776 Setting [DV3000] rxPort -> 2460
I: 2021-02-14
19:43:13.777 Open UDP listener on 127.0.0.1:31100
I: 2021-02-14
19:43:13.777 Open USRP on 127.0.0.1:32001
M: 2021-02-14
19:43:13.777 Connecting to DV3000 hardware......
W: 2021-02-14
19:43:13.871 DV3000 did not reset at 127.0.0.1:2460
W: 2021-02-14
19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset
failed)
I: 2021-02-14
19:43:16.072 Subscriber IDs loaded: 187850
I: 2021-02-14
19:43:16.073 Default extended metadata <K4KSA>
W: 2021-02-14
19:43:16.073 Using software MBE decoder version 1.2.3
W: 2021-02-14
19:43:16.073 Using software OP25 IMBE/AMBE vocoder
I: 2021-02-14
19:43:16.074 Sending to USRP clients at 127.0.0.1 on
port(s) 32001
I: 2021-02-14
19:43:16.074 Sending PCM to clients at 127.0.0.1 on port
2222
I: 2021-02-14
19:43:16.074 Starting TLV --> Analog_Bridge (decoder)
--> USRP thread
I: 2021-02-14
19:43:16.075 Starting USRP --> Analog_Bridge (encoder)
-> TLV thread
You have 2
channel drivers uncommented:
rxchannel = dahdi/pseudo ; No radio (hub)
<--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel = Pi/1 ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999 ; USBRadio (DSP)
; rxchannel = Dahdi/1 ; PCI Quad card
; rxchannel = Beagle/1 ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface
USRP
; rxchannel = Voter/1999 ; RTCM device
On 2/14/21 2:34 PM, Steve Siesel
[K4KSA] wrote:
Can you look at this as well…..
I cannot get ASL<> AB to
talk….Here is my rpt.cof and Analog_bridge.ini. RF from
talkgroup 31676 make it in the logs of AB and MB. When
able to talk on Allstar via Corey’s WS, I see the
transmission in Allstar but nothing past that.
Steve
; Your Repeater
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
[460310]
; Change this to your assigned node number
; Must also be enabled in modules.conf
; Rx audio/signalling channel. Choose ONLY 1 per node
stanza
; Enable the selected channel driver in modules.conf !!!
rxchannel =
dahdi/pseudo ; No radio (hub)
; rxchannel =
SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel =
Pi/1 ; Raspberry Pi PiTA
; rxchannel =
Radio/usb_1999 ; USBRadio (DSP)
; rxchannel =
Dahdi/1 ; PCI Quad card
; rxchannel =
Beagle/1 ; BeagleBoard
rxchannel =
USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel =
Voter/1999 ; RTCM device
duplex =
1 ; 0 = Half duplex with no
telemetry tones or hang time.
; Special Case: Full duplex if linktolink is set to
yes.
; This mode is preferred when interfacing with an
external multiport repeater controller.
; Comment out idrecording and idtalkover to suppress
IDs also
; 1 = Half duplex with telemetry tones and hang time.
Does not repeat audio.
; This mode is preferred when interfacing a simplex
node.
; 2 = Full Duplex with telemetry tones and hang time.
; This mode is preferred when interfacing a
repeater.
; 3 = Full Duplex with telemetry tones and hang time,
but no repeated audio.
; 4 = Full Duplex with telemetry tones and hang time.
Repeated audio only when the autopatch is down.
linktolink =
no ; disables forcing physical
half-duplex operation of main repeater while
; still keeping half-duplex semantics (optional)
linkmongain =
0 ; Link Monitor Gain adjusts
the audio level of monitored nodes when a signal from
another node or the local receiver is received.
; If linkmongain is set to a negative number the
monitored audio will decrease by the set amount in db.
; If linkmongain set to a positive number monitored
audio will increase by the set amount in db.
; The value of linkmongain is in db. The default value
is 0 db.
erxgain =
-3 ; Echolink receive gain
adjustment
; Note: Gain is in db-volts (20logVI/VO)
etxgain =
3 ; Echolink transmit gain
adjustment
; Note: Gain is in
db-volts (20logVI/VO)
;eannmode =
1 ; 1 = Say only node number
on echolink connects (default = 1)
; 2 = say phonetic call sign only on echolink connects
; 3 = say phonetic call sign
and node number on echolink connects
;controlstates
= controlstates ; system control state stanza
scheduler =
schedule ; scheduler stanza
functions =
functions ; Repeater Function stanza
phone_functions
= functions ; Phone Function stanza
link_functions
= functions ; Link Function stanza
telemetry =
telemetry ; Telemetry stanza
morse =
morse ; Morse stanza
wait_times =
wait-times ; Wait times stanza
context =
radio ; dialing context for
phone
callerid =
"Repeater" <0000000000> ; callerid for phone
calls
accountcode =
RADIO ; account code (optional)
hangtime =
5000 ; squelch tail hang time
(in ms) (optional, default 5 seconds, 5000 ms)
althangtime =
4000 ; longer squelch tail
totime =
180000 ; transmit time-out time
(in ms) (optional, default 3 minutes 180000 ms)
idrecording =
|iWA4XYZ ; cording or morse string see
http://ohnosec.org/drupal/node/87
idtalkover =
|iWA4XYZ ; Talkover ID (optional)
default is none see http://ohnosec.org/drupal/node/129
; See Telemetry section Example: idrecording =
rpt/nodenames/1999
idtime =
540000 ; id interval time (in
ms) (optional) Default 5 minutes (300000 ms)
politeid =
30000 ; time in milliseconds
before ID timer expires to try and ID in the tail.
(optional, default 30000)
unlinkedct =
ct2 ; Send a this courtesy tone
when the user unkeys if the node is not connected to any
other nodes. (optional, default is none)
remotect =
ct3 ; remote linked courtesy
tone (indicates a remote is in the list of links)
linkunkeyct =
ct8 ; sent when a transmission
received over the link unkeys
;nolocallinkct
= 0 ; Send unlinkedct instead if
another local node is connected to this node (hosted on
the same PC).
;connpgm =
yourconnectprogram ; Disabled. Execute a
program you specify on connect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being connected to us (them)
;discpgm =
yourdisconnectprogram ; Disabled. Execute a
program you specify on disconnect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being disconnected from us (them)
;lnkactenable =
0 ; Set to 1 to enable the link
activity timer. Applicable to standard nodes only.
;lnkacttime =
1800 ; Link activity timer time in
seconds.
;lnkactmacro =
*52 ; Function to execute when link
activity timer expires.
;lnkacttimerwarn
= 30seconds ; Message to play when the link
activity timer has 30 seconds left.
;remote_inact_timeout
= ; Specifies the amount of time without
keying from the link. Set to 0 to disable timeout. (15 *
60)
;remote_timeout
= ; Session time out for remote
base. Set to 0 to disable. (60 * 60)
;remote_timeout_warning_freq
= ; 30
;remote_timeout_warning
= ; (3 * 60)
;nounkeyct =
0 ; Set to a 1 to eliminate
courtesy tones and associated delays.
holdofftelem =
0 ; Hold off all telemetry when
signal is present on receiver or from connected nodes
; except when an ID needs to be done and there is a
signal coming from a connected node.
telemdefault =
0 ; 0 = telemetry output off
; 1 = telemetry output on (default =
1)
; 2 = timed telemetry output on command execution and
for a short time thereafter.
telemdynamic =
1 ; 0 = disallow users to change
the local telemetry setting with a COP command,
; 1 = Allow users to change the setting with a COP
command. (default = 1)
;beaconing =
0 ; Send ID regardless of
repeater activity (Required in the UK, but probably
illegal in the US)
parrotmode =
0 ; 0 = Parrot Off (default =
0)
; 1 = Parrot On Command
; 2 = Parrot Always
; 3 = Parrot Once by Command
parrottime =
1000 ; Set the amount of time in
milliseconds
; to wait before parroting what was received
;rxnotch=1065,40
; (Optional) Notch a particular frequency for a
specified
; b/w. app_rpt must have been compiled with
; the notch option
startup_macro =
; nodenames =
/var/lib/asterisk/sounds/rpt/nodenames.callsign ;
Point to alternate nodename sound directory
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Need more
information on these
;extnodes =
extnodes-different ; section in extnodefile containing
dynamic node information (optional)
;extnodefile =
/foo/nodes ; Points to nodelist file containing
dynamic node info default =
/var/lib/asterisk/rpt_extnodes (optional)
;extnodefile2
= ; Is this a list of node files?
Possible a list of private nodes or a list of static IPs
for known nodes????
;nodenames =
/foo/names ; locaton of node sound files default
= /var/lib/asterisk/sounds/rpt/nodenames
;archivedir =
/tmp ; defines and enables activity
recording into specified directory (optional)
;monminblocks =
2048 ; Min 1K blocks to be left on partition
(will not save monitor output if disk too full)
;
; The tailmessagetime,tailsquashedtime, and
tailmessagelist need to be set
;
; to support tail messages. They can be omitted
otherwise.
;tailmessagetime
= 300000 ; Play a tail message every 5 mins
;tailsquashedtime
= 30000 ; If squashed by another user,
;
; try again after 30 seconds
;tailmessagelist
= msg1,msg2 ; list of messages to be played for tail
message
; alt_functions
; ctgroup
;
dphone_functions
; idtime
; iobase
; iospeed
; locallist
; mars
Remote Base
; memory
; nobusyout
; nodes
; nolocallinkct
; notelemtx
; outxlat
; parrot
;
propagate_phonedtmf
; rptnode
;
rptinactmacro Macro to execute when inactivity timer
expires
;
rptinacttime Inactivity timer time in seconds (0
seconds disables feature)
; rxnotch
Optional Audio notch
;
simplexphonedelay
; tonemacro
; tonezone
; txlimits
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; *** Status
Reporting ***
; Comment the
following statpost line stop to reporting of the status
of your node to stats.allstarlink.org
statpost_url =
http://stats.allstarlink.org/uhandler
; Status updates
[functions]
; Prefix
Functions
; *1
Disconnect Link
; *2
Monitor Link
; *3
Connect Link
; *4
Command Mode
; *5
Macros
; *6
User Functions
; *7
Connection Status/Functions
; *8
User Functions
; *9
User Functions
; *0
User Functions
; *A
User Functions
; *B
User Functions
; *C
User Functions
; *D
User Functions
; Mandatory
Command Codes
; http://docs.allstarlink.org/drupal/node/91
1 =
ilink,1 ; Disconnect specified link
2 =
ilink,2 ; Connect specified link -- monitor
only
3 =
ilink,3 ; Connect specified link --
tranceive
4 =
ilink,4 ; Enter command mode on specified
link
70 =
ilink,5 ; System status
99 =
cop,6 ; PTT (phone mode only)
; End Mandatory
Command Codes
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Macro
Commands
5 = macro
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Autopatch
Commands
; Note, This
may be a good place for other 2 digit frequently used
commands
61 =
autopatchup,noct = 1,farenddisconnect = 1,dialtime =
20000 ; Autopatch up
62 =
autopatchdn
; Autopatch down
; autopatchup
can optionally take comma delimited setting=value pairs:
; context =
string ; Override default context with
"string"
; dialtime =
ms ; Specify the max number of
milliseconds between phone number digits (1000
milliseconds = 1 second)
;
farenddisconnect = 1 ; Automatically disconnect
when called party hangs up
; noct =
1 ; Don't send repeater courtesy
tone during autopatch calls
; quiet =
1 ; Don't send dial tone, or connect
messages. Do not send patch down message when called
party hangs up
; Example:
123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Status
Commands
; 1 - Force ID
(global)
; 2 - Give Time
of Day (global)
; 3 - Give
software Version (global)
; 4 - Give GPS
location info
; 5 - Last
(dtmf) user
; 11 - Force ID
(local only)
; 12 - Give
Time of Day (local only)
721 =
status,1 ; Force ID (global)
722 =
status,2 ; Give Time of Day (global)
723 =
status,3 ; Give software Version (global)
724 =
status,4 ; Give GPS location info
725 =
status,5 ; Last (dtmf) user
711 =
status,11 ; Force ID (local only)
712 =
status,12 ; Give Time of Day (local only)
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Link Commands
; 1 -
Disconnect specified link
; 2 - Connect
specified link -- monitor only
; 3 - Connect
specified link -- tranceive
; 4 - Enter
command mode on specified link
; 5 - System
status
; 6 -
Disconnect all links
; 7 - Last Node
to Key Up
; 8 - Connect
specified link -- local monitor only
; 9 - Send Text
Message (9,<destnodeno or 0 (for all)>,Message
Text, etc.
; 10 -
Disconnect all RANGER links (except permalinks)
; 11 -
Disconnect a previously permanently connected link
; 12 -
Permanently connect specified link -- monitor only
; 13 -
Permanently connect specified link -- tranceive
; 15 - Full
system status (all nodes)
; 16 -
Reconnect links disconnected with "disconnect all links"
; 17 - MDC test
(for diag purposes)
; 18 -
Permanently Connect specified link -- local monitor only
; ilink
commands 1 through 5 are defined in the Mandatory
Command section
806 =
ilink,6 ; Disconnect all links
807 =
ilink,7 ; Last Node to Key Up
808 =
ilink,8 ; Connect specified link --
local monitor only
809 =
ilink,9,1999,"Testing" ; would send a text message to
node 1999 replace 1999 with 0 for all connected nodes
810 =
ilink,10 ; Disconnect all RANGER links
(except permalinks)
811 =
ilink,11 ; Disconnect a previously
permanently connected link
812 =
ilink,12 ; Permanently connect
specified link -- monitor only
813 =
ilink,13 ; Permanently connect
specified link -- tranceive
815 =
ilink,15 ; Full system status (all
nodes)
816 =
ilink,16 ; Reconnect links disconnected
with "disconnect all links"
817 =
ilink,17 ; MDC test (for diag purposes)
818 = ilink
18 ; Permanently Connect specified link
-- local monitor only
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Control
operator (cop) functions. Change these to something
other than these codes listed below!
901 =
cop,1 �� ;
System warm boot
902 =
cop,2 ; System enable
903 =
cop,3 ; System disable
904 =
cop,4 ; Test tone on/off
(toggle)
905 =
cop,5 ; Dump system
variables on console (debug use only)
907 =
cop,7 ; Time out timer
enable
908 =
cop,8 ; Time out timer
disable
909 =
cop,9 ; Autopatch enable
910 =
cop,10 ; Autopatch disable
911 =
cop,11 ; User linking
functions enable
912 =
cop,12 ; User linking
functions disable
913 =
cop,13 ; Query system control
state
914 =
cop,14 ; Set system control
state
915 = cop,15
; Scheduler enable
916 =
cop,16 ; Scheduler disable
917 =
cop,17 ; User functions
enable (time, id, etc)
918 =
cop,18 ; User functions
disable
919 =
cop,19 ; Select alternate
hang time (althangtime)
920 =
cop,20 ; Select standard
hangtime (hangtime)
921 =
cop,21 ; Enable Parrot Mode
922 =
cop,22 ; Disable Parrot Mode
923 =
cop,23 ; Birdbath (Current
Parrot Cleanup/Flush)
924 =
cop,24 ; Flush all telemetry
925 =
cop,25 ; Query last node
un-keyed
926 =
cop,26 ; Query all nodes
keyed/unkeyed
927 =
cop,27 ; Reset DAQ minimum on
a pin
928 =
cop,28 ; Reset DAQ maximum on
a pin
930 =
cop,30 ; Recall Memory
Setting in Attached Xcvr
931 =
cop,31 ; Channel Selector for
Parallel Programmed Xcvr
932 =
cop,32 ; Touchtone pad test:
command + Digit string + # to playback all digits
pressed
933 =
cop,33 ; Local Telemetry
Output Enable
934 =
cop,34 ; Local Telemetry
Output Disable
935 =
cop,35 ; Local Telemetry
Output on Demand
936 =
cop,36 ; Foreign Link Local
Output Path Enable
937 =
cop,37 ; Foreign Link Local
Output Path Disable
938 =
cop,38 ; Foreign Link Local
Output Path Follows Local Telemetry
939 =
cop,39 ; Foreign Link Local
Output Path on Demand
942 =
cop,42 ; Echolink announce
node # only
943 =
cop,43 ; Echolink announce
node Callsign only
944 =
cop,44 ; Echolink announce
node # & Callsign
945 =
cop,45 ; Link Activity timer
enable
945 =
cop,46 ; Link Activity timer
disable
947 =
cop,47 ; Reset "Link Config
Changed" Flag
948 =
cop,48 ; Send Page Tone (Tone
specs separated by parenthesis)
949 =
cop,49 ; Disable incoming
connections (control state noice)
950 =
cop,50 ; Enable incoming
connections (control state noicd)
951 =
cop,51 ; Enable sleep mode
952 =
cop,52 ; Disable sleep mode
953 =
cop,53 ; Wake up from sleep
954 =
cop,54 ; Go to sleep
955 =
cop,55 ; Parrot Once if
parrot mode is disabled
956 =
cop,56 ; Rx CTCSS Enable
957 =
cop,57 ; Rx CTCSS Disable
958 =
cop.58 ; Tx CTCSS On Input
only Enable
959 =
cop,59 ; Tx CTCSS On Input
only Disable
960 =
cop,60 ; Send MDC-1200 Burst
(cop,60,type,UnitID[,DestID,SubCode])
; Type is 'I' for PttID, 'E' for Emergency, and 'C' for
Call
; (SelCall or Alert), or 'SX' for STS (ststus), where X
is 0-F.
; DestID and subcode are only specified for the 'C'
type message.
; UnitID is the local systems UnitID. DestID is the
MDC1200 ID of
; the radio being called, and the subcodes are as
follows:
; Subcode '8205' is Voice Selective Call for Spectra
('Call')
; Subcode '8015' is Voice Selective Call for Maxtrac
('SC') or
; Astro-Saber('Call')
; Subcode '810D' is Call Alert (like Maxtrac 'CA')
961 =
cop,61 ; Send Message to USB
to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)
962 =
cop,62 ; Send Message to USB
to control GPIO pins, quietly
(cop,62,GPIO1=0[,GPIO4=1].....)
963 =
cop,63 ; Send pre-configred
APRSTT notification (cop,63,CALL[,OVERLAYCHR])
964 =
cop,64 ; Send pre-configred
APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])
965 =
cop,65 ; Send POCSAG page
(equipped channel types only)
[functions-remote]
0 =
remote,1 ; Retrieve Memory
1 =
remote,2 ; Set freq.
2 =
remote,3 ; Set tx PL tone
3 =
remote,4 ; Set rx PL tone
40 =
remote,100 ; Rx PL off
41 =
remote,101 ; Rx PL on
42 =
remote,102 ; Tx PL off
43 =
remote,103 ; Tx PL on
44 =
remote,104 ; Low Power
45 =
remote,105 ; Medium Power
46 =
remote,106 ; High Power
711 =
remote,107 ; Bump -20
714 =
remote,108 ; Bump -100
717 =
remote,109 ; Bump -500
713 =
remote,110 ; Bump +20
716 =
remote,111 ; Bump +100
719 =
remote,112 ; Bump +500
721 =
remote,113 ; Scan - slow
724 =
remote,114 ; Scan - quick
727 =
remote,115 ; Scan - fast
723 =
remote,116 ; Scan + slow
726 =
remote,117 ; Scan + quick
729 =
remote,118 ; Scan + fast
79 =
remote,119 ; Tune
51 =
remote,5 ; Long status query
52 =
remote,140 ; Short status query
67 =
remote,210 ; Send a *
69 =
remote,211 ; Send a #
;91 =
remote,99,CALLSIGN,LICENSETAG ; Remote base login.
; Define a different dtmf sequence for each user which
is
; authorized to use the remote base to control access to
it.
; For examble 9139583=remote,99,WB6NIL,G would grant
access to
; the remote base and announce WB6NIL as being logged
in.
; Another entry, 9148351=remote,99,WA6ZFT,E would grant
access to
; the remote base and
announce WA6ZFT as being logged in.
; When the remote base is disconnected from the
originating node, the
; user will be logged out. The LICENSETAG argument is
used to enforce
; tx frequency limits. See [txlimits] below.
85 =
cop,6 ; Remote base
telephone key
[telemetry]
; Telemetry
entries can be shared across all repeaters, or defined
for each repeater.
; Can be a tone
sequence, morse string, or a file
;
; |t - Tone
escape sequence
;
; Tone
sequences consist of 1 or more 4-tuple entries (freq1,
freq2, duration, amplitude)
; Single
frequencies are created by setting freq1 or freq2 to
zero.
;
; |m - Morse
escape sequence
;
; Sends Morse
code at the telemetry amplitude and telemetry frequency
as defined in the
; [morse]
section.
;
; Follow with
an alphanumeric string
;
; |i - Morse ID
escape sequence
;
; Sends Morse
code at the ID amplitude and ID frequency as defined in
the
; [morse]
section.
;
;
path/to/sound/file/without/extension
;
; Send the
sound if in place of a constructed tone. Do not include
the file extension
; Example: ct8
= rpt/bloop
; Example:
idrecording = rpt/nodenames/1999
ct1 =
|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2 =
|t(660,880,150,2048)
ct3 =
|t(440,0,150,4096)
ct4 =
|t(550,0,150,2048)
ct5 =
|t(660,0,150,2048)
ct6 =
|t(880,0,150,2048)
ct7 =
|t(660,440,150,2048)
ct8 =
|t(700,1100,150,2048)
ranger =
|t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)
remotemon =
|t(1209,0,50,2048) ;
local courtesy tone when receive only
remotetx =
|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ;
local courtesy tone when linked Trancieve mode
cmdmode =
|t(900,903,200,2048)
functcomplete =
|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
remcomplete =
|t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)
pfxtone =
|t(350,440,30000,3072)
patchup =
rpt/callproceeding
patchdown =
rpt/callterminated
; As far as
what the numbers mean,
;
(000,000,010,000)
; | | |
|-------amplitude
; | |
|-------------duration
; |
|-------------------Tone 2
;
|-------------------------Tone 1
; So, with
0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0
Amplitude.
; Use it for a
delay. Fine tuning for how long before telemetry is
sent, in conjunction with the telemdelay parameter)
; The numbers,
like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay,
amplitude of 2048.
; Morse code
parameters, these are common to all repeaters.
[morse]
speed =
20 ; Approximate speed in
WPM
frequency =
800 ; Morse Telemetry Frequency
amplitude =
4096 ; Morse Telemetry Amplitude
idfrequency =
1065 ; Morse ID Frequency
idamplitude =
1024 ; Morse ID Amplitude
;
; This section
allows wait times for telemetry events to be adjusted
; A section for
wait times can be defined for every repeater
;
[wait-times]
telemwait =
2000 ; Time to wait before
sending most telemetry
idwait =
500 ; Time to wait before
starting ID
unkeywait =
2000 ; Time to wait after unkey
before sending CT's and link telemetry
calltermwait =
2000 ; Time to wait before
announcing "call terminated"
;
; This is where
you define your nodes which cam be connected to.
;
[nodes]
; Note, if you
are using automatic update for allstar link nodes,
; no allstar
link nodes should be defined here. Only place a
definition
; for your
local nodes, and private (off of allstar link) nodes
here.
460310 = radio@....0.1:4569/460310,NONE
; This must be changed to your node number
; and iax port number if not the default
; Memories for
remote bases
[memory]
;00 =
146.580,100.0,m
;01 =
147.030,103.5,m+t
;02 =
147.240,103.5,m+t
;03 =
147.765,79.7,m-t
;04 =
146.460,100.0,m
;05 =
146.550,100.0,m
; Place command
macros here
[macro]
;1 = *32011#
;2 =
*12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#
;3 =
*32001*32011*32050*32030*32060#
; Data
Acquisition configuration
;[daq-list]
;device =
device_name1
;device =
device_name2
;Where:
device_name1 and device_name2 are stanzas you define in
this file
;device =
daq-cham-1
; Device name
;[daq-cham-1]
; Defined in [daq-list]
;hwtype =
uchameleon ; DAQ hardware type
;devnode =
/dev/ttyUSB0 ; DAQ device node (if
required)
;1 =
inadc ; Pin definition for
an ADC channel
;2 = inadc
;3 = inadc
;4 = inadc
;5 = inadc
;6 = inadc
;7 = inadc
;8 = inadc
;9 =
inp ; Pin definition for
an input with a weak pullup resistor
;10 = inp
;11 = inp
;12 = inp
;13 =
in ; Pin definition for
an input without a weak pullup resistor
;14 =
out ; Pin definition for
an output
;15 = out
;16 = out
;17 = out
;18 = out
;[meter-faces]
;face =
scale(scalepre,scalediv,scalepost),word/?,...
;
; scalepre =
offset to add before dividing with scalediv
; scalediv =
full scale/number of whole units (e.g. 256/20 or 12.8
for 20 volts).
; scalepost =
offset to add after dividing with scalediv
;
;face =
range(X-Y:word,X2-Y2:word,...),word/?,...
;face =
bit(low-word,high-word),word/?,...
;
; word/? is
either a word in /var/lib/asterisk/sounds or one of its
subdirectories,
; or a question
mark which is a placeholder for the measured value.
;
;
; Battery
voltage 0-20 volts
;batvolts =
scale(0,12.8,0),rpt/thevoltageis,?,ha/volts
; 4 quadrant
wind direction
;winddir =
range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?
; LM34
temperature sensor with 130 deg. F full scale
;lm34f =
scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit
; Status poll
(non alarmed)
;light =
bit(ha/off,ha/on),ha/light,?
;[alarms]
;
;tag =
device,pin,node,ignorefirst,func-low,func-hi
;
;tag = a unique
name for the alarm
;device = daq
device to poll
;pin = the
device pin to be monitored
;ignorefirstalarm
= set to 1 to throwaway first alarm event, or 0 to
report it
;node = the
node number to execute the function on
;func-low = the
DTMF function to execute on a high to low transition
;func-high =
the DTMF function to execute on a low to high transition
;
; a '-' as a
function name is shorthand for no-operation
;
;door =
daq-cham-1,9,1,2017,*7,-
;pwrfail =
daq-cham-1,10,0,2017,*911111,-
;
; Control
states
; Allow several
control operator functions to be changed at once using
one command (good for scheduling)
;
;[controlstates]
;statenum =
copcmd,[copcmd]...
;0 =
rptena,lnkena,apena,totena,ufena,noicd ; Normal
operation
;1 =
rptena,lnkena,apdis,totdis,ufena,noice ; Net and news
operation
;2 =
rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only
operation
; Scheduler -
execute a macro at a given time
[schedule]
;dtmf_function
= m h dom mon dow ; ala cron, star is implied
;2 = 00 00 * *
* ; at midnight, execute macro 2.
#includeifexists
custom/rpt.conf
Analog_Bridge.ini
; Analog_Bridge
configuration file.
; This file
should be placed in either /etc or it can be
; supplied as
a path on the Analog_Bridge command line.
; The best way
to think of this file is that there are two main
sections, the USRP (analog audio) and
; AMBE_AUDIO
(compressed audio). Analog_Bridge will take everything
sent to the USRP port and
; encode it for
transmission on the AMBE_AUDIO port. The encoder will
use the format defined in ambeMode.
; As you might
expect, the reverse direction is defined too.
; Analog_Bridge
supports include files. More on this later...
include =
dvsm.macro
; include =
asl.macro
; General
Section describes settings for Analog_Bridge itself.
[GENERAL]
logLevel =
2 ; Show messages and above
0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning,
5=Error, 6=Fatal
; Metadata
management
exportMetadata
= true ; Export metadata to USRP
partner (transcode setups require this)
transferRootDir
= /tmp ; Export database files to USRP
partner
subscriberFile
= /var/lib/dvswitch/subscriber_ids.csv ; DMR ID to
callsign lookup data
; General
vocoder setup information
decoderFallBack
= true ; Allow software AMBE decoding
if a hardware decoder is not found
useEmulator =
false ; Use the MD380 AMBE emulator
for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress
= 127.0.0.1:2470 ; IP address and port of the
md380 server
pcmPort =
2222 ; UDP port to send to the
WebProxy
; Information
for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
[AMBE_AUDIO]
address =
127.0.0.1 ; IP address of xx_Bridge
txPort =
31103 ; Transmit TLV frames to
partner on this port
rxPort =
31100 ; Listen for TLV frames
from partner on this port
ambeMode =
DMR ; DMR, DMR_IPSC, DSTAR,
NXDN, P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS =
2500 ; Analog -> Digital Minimum
time in MS for hang delay (0-10000)
; The metadata
below is used when ASL is the source since it does not
have any concept of digital modes
gatewayDmrId =
1112721 ; ID to use when transmitting
from Analog_Bridge 7 digit ID
repeaterID =
111272123 ; ID of source repeater 7
digit ID plus 2 digit SSID
txTg =
31676 ; TG to use for all
frames sent from Analog_Bridge -> xx_Bridge
txTs =
2 ; Slot to use for
frames sent from Analog_Bridge -> xx_Bridge
colorCode =
1 ; Color Code to assign DMR
frames
; Information
for USRP channel driver. This interface uses PCM to
transfer audio information
; There are two
typical configurations, ASL and Transcode. ASL
(AllstarLink) is for analog clients connected
; to a digital
network. Transcode is when Analog_Bridge actually
points its PCM interfaces back at itself,
; causing a TLV
<-- (pcm <--> pcm) --> TLV type of
architecture.
; When using
ASL, this matches the rpt.conf ASL file with a setting
like:
; rxchannel =
usrp/127.0.0.1:34001:32001
; When
Transcoding, make two ini files and set txPort equal to
the other instance rxPort (crossover). Launch
; each
instance with its own ini file.
[USRP]
address =
127.0.0.1 ; IP address of USRP
partner (Allstar/Asterisk or another Analog_Bridge)
txPort =
32001 ; Transmit USRP frames on
this port
rxPort =
34001 ; Listen for USRP frames
on this port
usrpAudio =
AUDIO_UNITY ; Digital -> Analog
(AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC)
usrpGain =
1.10 ; Gain factor when
usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 =
AUDIO_UNITY)
usrpAGC =
-20,10,100 ; Set the agc threshold
(db), slope (db) and decay (ms)
tlvAudio =
AUDIO_UNITY ; Analog -> Digital
(AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain =
0.35 ; Gain factor when
tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 =
AUDIO_UNITY)
[MACROS]
; Where the
macros are
; xxxx=yyyy
; xxxx is the
dial string to match
; yyyy is the
command line to execute
; xxxx must be
preceded by a *
; xxxx can be
any string (alphanumeric)
; yyyy is the
command to execute
; yyyy will
replace xxxx in the dial string
; arguments
follow the macro name with a # delimiter
; For example
using macro "5678" above would look like:
; *5678#9876
; Which would
invoke:
; echo 9876
; Information
for DV3000 hardware decoder
; There are
two configuration modes: IP (AMBEServer) and serial
(direct connect hardware)
; Use top
server and port if using AMBEServer
; Use bottom
server/port and serial = true if using the DV3000u
(thumbdv)
; Did you run
AMBETest4.py before using this?
[DV3000]
address =
127.0.0.1 ; IP address of AMBEServer
rxPort =
2460 ; Port of AMBEServer
; address =
/dev/ttyUSB0 ; Device of DV3000U on this
machine
; baud =
460800 ; Baud rate of the dongle
(230400 or 460800)
; serial =
true ; Use serial=true f
|
|
|
It is now working…Long hangtime I think I will change Hangtime to 20
From: main@DVSwitch.groups.io [mailto:main@DVSwitch.groups.io] On Behalf Of Steve N4IRS Sent: Sunday, February 14, 2021 2:51 PM To: main@DVSwitch.groups.io Subject: Re: [DVSwitch] ASL<>AB Is chan_usrp enabled in modules.conf? On 2/14/21 2:50 PM, Steve Siesel [K4KSA] wrote: Yes….. Did you fix rpt.conf and did you then restart asterisk? On 2/14/21 2:46 PM, Steve Siesel [K4KSA] wrote: After restarting AB and Asterisk….also md3890-emu is running Still no Joy…Here is the latest start of Analog_bridge.log I: 2021-02-14 19:43:13.761 Analog_Bridge is starting M: 2021-02-14 19:43:13.762 Setting [MACROS] DMR -> /opt/MMDVM_Bridge/dvswitch.sh mode DMR M: 2021-02-14 19:43:13.762 Setting [MACROS] DSTAR -> /opt/MMDVM_Bridge/dvswitch.sh mode DSTAR M: 2021-02-14 19:43:13.762 Setting [MACROS] NXDN -> /opt/MMDVM_Bridge/dvswitch.sh mode NXDN M: 2021-02-14 19:43:13.762 Setting [MACROS] P25 -> /opt/MMDVM_Bridge/dvswitch.sh mode P25 M: 2021-02-14 19:43:13.762 Setting [MACROS] YSF -> /opt/MMDVM_Bridge/dvswitch.sh mode YSF M: 2021-02-14 19:43:13.762 Setting [MACROS] dbupdate -> /opt/MMDVM_Bridge/dvswitch.sh collectProcessPushDataFiles M: 2021-02-14 19:43:13.764 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh M: 2021-02-14 19:43:13.765 Setting [] include -> dvsm.macro M: 2021-02-14 19:43:13.766 Setting [GENERAL] logLevel -> 2 M: 2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata -> true M: 2021-02-14 19:43:13.767 Setting [GENERAL] transferRootDir -> /tmp M: 2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv M: 2021-02-14 19:43:13.768 Setting [GENERAL] decoderFallBack -> true M: 2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator -> false M: 2021-02-14 19:43:13.769 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470 M: 2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort -> 2222 M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address -> 127.0.0.1 M: 2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort -> 31103 M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort -> 31100 M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode -> DMR M: 2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS -> 2500 M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] gatewayDmrId -> 1112721 M: 2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID -> 111272123 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg -> 31676 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs -> 2 M: 2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode -> 1 M: 2021-02-14 19:43:13.773 Setting [USRP] address -> 127.0.0.1 M: 2021-02-14 19:43:13.773 Setting [USRP] txPort -> 32001 M: 2021-02-14 19:43:13.773 Setting [USRP] rxPort -> 34001 M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAudio -> AUDIO_UNITY M: 2021-02-14 19:43:13.774 Setting [USRP] usrpGain -> 1.10 M: 2021-02-14 19:43:13.774 Setting [USRP] usrpAGC -> -20,10,100 M: 2021-02-14 19:43:13.775 Setting [USRP] tlvAudio -> AUDIO_UNITY M: 2021-02-14 19:43:13.775 Setting [USRP] tlvGain -> 0.35 M: 2021-02-14 19:43:13.776 Setting [DV3000] address -> 127.0.0.1 M: 2021-02-14 19:43:13.776 Setting [DV3000] rxPort -> 2460 I: 2021-02-14 19:43:13.777 Open UDP listener on 127.0.0.1:31100 I: 2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001 M: 2021-02-14 19:43:13.777 Connecting to DV3000 hardware...... W: 2021-02-14 19:43:13.871 DV3000 did not reset at 127.0.0.1:2460 W: 2021-02-14 19:43:13.871 DV3000 not found at 127.0.0.1:2460 (Reset failed) I: 2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850 I: 2021-02-14 19:43:16.073 Default extended metadata <K4KSA> W: 2021-02-14 19:43:16.073 Using software MBE decoder version 1.2.3 W: 2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE vocoder I: 2021-02-14 19:43:16.074 Sending to USRP clients at 127.0.0.1 on port(s) 32001 I: 2021-02-14 19:43:16.074 Sending PCM to clients at 127.0.0.1 on port 2222 I: 2021-02-14 19:43:16.074 Starting TLV --> Analog_Bridge (decoder) --> USRP thread I: 2021-02-14 19:43:16.075 Starting USRP --> Analog_Bridge (encoder) -> TLV thread You have 2 channel drivers uncommented:
rxchannel = dahdi/pseudo ; No radio (hub) <--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel = Pi/1 ; Raspberry Pi PiTA
; rxchannel = Radio/usb_1999 ; USBRadio (DSP)
; rxchannel = Dahdi/1 ; PCI Quad card
; rxchannel = Beagle/1 ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/1999 ; RTCM device On 2/14/21 2:34 PM, Steve Siesel [K4KSA] wrote: Can you look at this as well….. I cannot get ASL<> AB to talk….Here is my rpt.cof and Analog_bridge.ini. RF from talkgroup 31676 make it in the logs of AB and MB. When able to talk on Allstar via Corey’s WS, I see the transmission in Allstar but nothing past that. Steve ; Your Repeater ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; [460310] ; Change this to your assigned node number ; Must also be enabled in modules.conf ; Rx audio/signalling channel. Choose ONLY 1 per node stanza ; Enable the selected channel driver in modules.conf !!! rxchannel = dahdi/pseudo ; No radio (hub) ; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_1999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP ; rxchannel = Voter/1999 ; RTCM device duplex = 1 ; 0 = Half duplex with no telemetry tones or hang time. ; Special Case: Full duplex if linktolink is set to yes. ; This mode is preferred when interfacing with an external multiport repeater controller. ; Comment out idrecording and idtalkover to suppress IDs also ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio. ; This mode is preferred when interfacing a simplex node. ; 2 = Full Duplex with telemetry tones and hang time. ; This mode is preferred when interfacing a repeater. ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio. ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down. linktolink = no ; disables forcing physical half-duplex operation of main repeater while ; still keeping half-duplex semantics (optional) linkmongain = 0 ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received. ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db. ; If linkmongain set to a positive number monitored audio will increase by the set amount in db. ; The value of linkmongain is in db. The default value is 0 db. erxgain = -3 ; Echolink receive gain adjustment ; Note: Gain is in db-volts (20logVI/VO) etxgain = 3 ; Echolink transmit gain adjustment ; Note: Gain is in db-volts (20logVI/VO) ;eannmode = 1 ; 1 = Say only node number on echolink connects (default = 1) ; 2 = say phonetic call sign only on echolink connects ; 3 = say phonetic call sign and node number on echolink connects ;controlstates = controlstates ; system control state stanza scheduler = schedule ; scheduler stanza functions = functions ; Repeater Function stanza phone_functions = functions ; Phone Function stanza link_functions = functions ; Link Function stanza telemetry = telemetry ; Telemetry stanza morse = morse ; Morse stanza wait_times = wait-times ; Wait times stanza context = radio ; dialing context for phone callerid = "Repeater" <0000000000> ; callerid for phone calls accountcode = RADIO ; account code (optional) hangtime = 5000 ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms) althangtime = 4000 ; longer squelch tail totime = 180000 ; transmit time-out time (in ms) (optional, default 3 minutes 180000 ms) idrecording = |iWA4XYZ ; cording or morse string see http://ohnosec.org/drupal/node/87 idtalkover = |iWA4XYZ ; Talkover ID (optional) default is none see http://ohnosec.org/drupal/node/129 ; See Telemetry section Example: idrecording = rpt/nodenames/1999 idtime = 540000 ; id interval time (in ms) (optional) Default 5 minutes (300000 ms) politeid = 30000 ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000) unlinkedct = ct2 ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none) remotect = ct3 ; remote linked courtesy tone (indicates a remote is in the list of links) linkunkeyct = ct8 ; sent when a transmission received over the link unkeys ;nolocallinkct = 0 ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC). ;connpgm = yourconnectprogram ; Disabled. Execute a program you specify on connect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being connected to us (them) ;discpgm = yourdisconnectprogram ; Disabled. Execute a program you specify on disconnect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being disconnected from us (them) ;lnkactenable = 0 ; Set to 1 to enable the link activity timer. Applicable to standard nodes only. ;lnkacttime = 1800 ; Link activity timer time in seconds. ;lnkactmacro = *52 ; Function to execute when link activity timer expires. ;lnkacttimerwarn = 30seconds ; Message to play when the link activity timer has 30 seconds left. ;remote_inact_timeout = ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60) ;remote_timeout = ; Session time out for remote base. Set to 0 to disable. (60 * 60) ;remote_timeout_warning_freq = ; 30 ;remote_timeout_warning = ; (3 * 60) ;nounkeyct = 0 ; Set to a 1 to eliminate courtesy tones and associated delays. holdofftelem = 0 ; Hold off all telemetry when signal is present on receiver or from connected nodes ; except when an ID needs to be done and there is a signal coming from a connected node. telemdefault = 0 ; 0 = telemetry output off ; 1 = telemetry output on (default = 1) ; 2 = timed telemetry output on command execution and for a short time thereafter. telemdynamic = 1 ; 0 = disallow users to change the local telemetry setting with a COP command, ; 1 = Allow users to change the setting with a COP command. (default = 1) ;beaconing = 0 ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US) parrotmode = 0 ; 0 = Parrot Off (default = 0) ; 1 = Parrot On Command ; 2 = Parrot Always ; 3 = Parrot Once by Command parrottime = 1000 ; Set the amount of time in milliseconds ; to wait before parroting what was received ;rxnotch=1065,40 ; (Optional) Notch a particular frequency for a specified ; b/w. app_rpt must have been compiled with ; the notch option startup_macro = ; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign ; Point to alternate nodename sound directory ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Need more information on these ;extnodes = extnodes-different ; section in extnodefile containing dynamic node information (optional) ;extnodefile = /foo/nodes ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional) ;extnodefile2 = ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes???? ;nodenames = /foo/names ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames ;archivedir = /tmp ; defines and enables activity recording into specified directory (optional) ;monminblocks = 2048 ; Min 1K blocks to be left on partition (will not save monitor output if disk too full) ; ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set ; ; to support tail messages. They can be omitted otherwise. ;tailmessagetime = 300000 ; Play a tail message every 5 mins ;tailsquashedtime = 30000 ; If squashed by another user, ; ; try again after 30 seconds ;tailmessagelist = msg1,msg2 ; list of messages to be played for tail message ; alt_functions ; ctgroup ; dphone_functions ; idtime ; iobase ; iospeed ; locallist ; mars Remote Base ; memory ; nobusyout ; nodes ; nolocallinkct ; notelemtx ; outxlat ; parrot ; propagate_phonedtmf ; rptnode ; rptinactmacro Macro to execute when inactivity timer expires ; rptinacttime Inactivity timer time in seconds (0 seconds disables feature) ; rxnotch Optional Audio notch ; simplexphonedelay ; tonemacro ; tonezone ; txlimits ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; *** Status Reporting *** ; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org statpost_url = http://stats.allstarlink.org/uhandler ; Status updates [functions] ; Prefix Functions ; *1 Disconnect Link ; *2 Monitor Link ; *3 Connect Link ; *4 Command Mode ; *5 Macros ; *6 User Functions ; *7 Connection Status/Functions ; *8 User Functions ; *9 User Functions ; *0 User Functions ; *A User Functions ; *B User Functions ; *C User Functions ; *D User Functions ; Mandatory Command Codes ; http://docs.allstarlink.org/drupal/node/91 1 = ilink,1 ; Disconnect specified link 2 = ilink,2 ; Connect specified link -- monitor only 3 = ilink,3 ; Connect specified link -- tranceive 4 = ilink,4 ; Enter command mode on specified link 70 = ilink,5 ; System status 99 = cop,6 ; PTT (phone mode only) ; End Mandatory Command Codes ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Macro Commands 5 = macro ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Autopatch Commands ; Note, This may be a good place for other 2 digit frequently used commands 61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000 ; Autopatch up 62 = autopatchdn ; Autopatch down ; autopatchup can optionally take comma delimited setting=value pairs: ; context = string ; Override default context with "string" ; dialtime = ms ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second) ; farenddisconnect = 1 ; Automatically disconnect when called party hangs up ; noct = 1 ; Don't send repeater courtesy tone during autopatch calls ; quiet = 1 ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Status Commands ; 1 - Force ID (global) ; 2 - Give Time of Day (global) ; 3 - Give software Version (global) ; 4 - Give GPS location info ; 5 - Last (dtmf) user ; 11 - Force ID (local only) ; 12 - Give Time of Day (local only) 721 = status,1 ; Force ID (global) 722 = status,2 ; Give Time of Day (global) 723 = status,3 ; Give software Version (global) 724 = status,4 ; Give GPS location info 725 = status,5 ; Last (dtmf) user 711 = status,11 ; Force ID (local only) 712 = status,12 ; Give Time of Day (local only) ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Link Commands ; 1 - Disconnect specified link ; 2 - Connect specified link -- monitor only ; 3 - Connect specified link -- tranceive ; 4 - Enter command mode on specified link ; 5 - System status ; 6 - Disconnect all links ; 7 - Last Node to Key Up ; 8 - Connect specified link -- local monitor only ; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc. ; 10 - Disconnect all RANGER links (except permalinks) ; 11 - Disconnect a previously permanently connected link ; 12 - Permanently connect specified link -- monitor only ; 13 - Permanently connect specified link -- tranceive ; 15 - Full system status (all nodes) ; 16 - Reconnect links disconnected with "disconnect all links" ; 17 - MDC test (for diag purposes) ; 18 - Permanently Connect specified link -- local monitor only ; ilink commands 1 through 5 are defined in the Mandatory Command section 806 = ilink,6 ; Disconnect all links 807 = ilink,7 ; Last Node to Key Up 808 = ilink,8 ; Connect specified link -- local monitor only 809 = ilink,9,1999,"Testing" ; would send a text message to node 1999 replace 1999 with 0 for all connected nodes 810 = ilink,10 ; Disconnect all RANGER links (except permalinks) 811 = ilink,11 ; Disconnect a previously permanently connected link 812 = ilink,12 ; Permanently connect specified link -- monitor only 813 = ilink,13 ; Permanently connect specified link -- tranceive 815 = ilink,15 ; Full system status (all nodes) 816 = ilink,16 ; Reconnect links disconnected with "disconnect all links" 817 = ilink,17 ; MDC test (for diag purposes) 818 = ilink 18 ; Permanently Connect specified link -- local monitor only ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Control operator (cop) functions. Change these to something other than these codes listed below! 901 = cop,1 �� ; System warm boot 902 = cop,2 ; System enable 903 = cop,3 ; System disable 904 = cop,4 ; Test tone on/off (toggle) 905 = cop,5 ; Dump system variables on console (debug use only) 907 = cop,7 ; Time out timer enable 908 = cop,8 ; Time out timer disable 909 = cop,9 ; Autopatch enable 910 = cop,10 ; Autopatch disable 911 = cop,11 ; User linking functions enable 912 = cop,12 ; User linking functions disable 913 = cop,13 ; Query system control state 914 = cop,14 ; Set system control state 915 = cop,15 ; Scheduler enable 916 = cop,16 ; Scheduler disable 917 = cop,17 ; User functions enable (time, id, etc) 918 = cop,18 ; User functions disable 919 = cop,19 ; Select alternate hang time (althangtime) 920 = cop,20 ; Select standard hangtime (hangtime) 921 = cop,21 ; Enable Parrot Mode 922 = cop,22 ; Disable Parrot Mode 923 = cop,23 ; Birdbath (Current Parrot Cleanup/Flush) 924 = cop,24 ; Flush all telemetry 925 = cop,25 ; Query last node un-keyed 926 = cop,26 ; Query all nodes keyed/unkeyed 927 = cop,27 ; Reset DAQ minimum on a pin 928 = cop,28 ; Reset DAQ maximum on a pin 930 = cop,30 ; Recall Memory Setting in Attached Xcvr 931 = cop,31 ; Channel Selector for Parallel Programmed Xcvr 932 = cop,32 ; Touchtone pad test: command + Digit string + # to playback all digits pressed 933 = cop,33 ; Local Telemetry Output Enable 934 = cop,34 ; Local Telemetry Output Disable 935 = cop,35 ; Local Telemetry Output on Demand 936 = cop,36 ; Foreign Link Local Output Path Enable 937 = cop,37 ; Foreign Link Local Output Path Disable 938 = cop,38 ; Foreign Link Local Output Path Follows Local Telemetry 939 = cop,39 ; Foreign Link Local Output Path on Demand 942 = cop,42 ; Echolink announce node # only 943 = cop,43 ; Echolink announce node Callsign only 944 = cop,44 ; Echolink announce node # & Callsign 945 = cop,45 ; Link Activity timer enable 945 = cop,46 ; Link Activity timer disable 947 = cop,47 ; Reset "Link Config Changed" Flag 948 = cop,48 ; Send Page Tone (Tone specs separated by parenthesis) 949 = cop,49 ; Disable incoming connections (control state noice) 950 = cop,50 ; Enable incoming connections (control state noicd) 951 = cop,51 ; Enable sleep mode 952 = cop,52 ; Disable sleep mode 953 = cop,53 ; Wake up from sleep 954 = cop,54 ; Go to sleep 955 = cop,55 ; Parrot Once if parrot mode is disabled 956 = cop,56 ; Rx CTCSS Enable 957 = cop,57 ; Rx CTCSS Disable 958 = cop.58 ; Tx CTCSS On Input only Enable 959 = cop,59 ; Tx CTCSS On Input only Disable 960 = cop,60 ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode]) ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F. ; DestID and subcode are only specified for the 'C' type message. ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of ; the radio being called, and the subcodes are as follows: ; Subcode '8205' is Voice Selective Call for Spectra ('Call') ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or ; Astro-Saber('Call') ; Subcode '810D' is Call Alert (like Maxtrac 'CA') 961 = cop,61 ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....) 962 = cop,62 ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....) 963 = cop,63 ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR]) 964 = cop,64 ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR]) 965 = cop,65 ; Send POCSAG page (equipped channel types only) [functions-remote] 0 = remote,1 ; Retrieve Memory 1 = remote,2 ; Set freq. 2 = remote,3 ; Set tx PL tone 3 = remote,4 ; Set rx PL tone 40 = remote,100 ; Rx PL off 41 = remote,101 ; Rx PL on 42 = remote,102 ; Tx PL off 43 = remote,103 ; Tx PL on 44 = remote,104 ; Low Power 45 = remote,105 ; Medium Power 46 = remote,106 ; High Power 711 = remote,107 ; Bump -20 714 = remote,108 ; Bump -100 717 = remote,109 ; Bump -500 713 = remote,110 ; Bump +20 716 = remote,111 ; Bump +100 719 = remote,112 ; Bump +500 721 = remote,113 ; Scan - slow 724 = remote,114 ; Scan - quick 727 = remote,115 ; Scan - fast 723 = remote,116 ; Scan + slow 726 = remote,117 ; Scan + quick 729 = remote,118 ; Scan + fast 79 = remote,119 ; Tune 51 = remote,5 ; Long status query 52 = remote,140 ; Short status query 67 = remote,210 ; Send a * 69 = remote,211 ; Send a # ;91 = remote,99,CALLSIGN,LICENSETAG ; Remote base login. ; Define a different dtmf sequence for each user which is ; authorized to use the remote base to control access to it. ; For examble 9139583=remote,99,WB6NIL,G would grant access to ; the remote base and announce WB6NIL as being logged in. ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to ; the remote base and announce WA6ZFT as being logged in. ; When the remote base is disconnected from the originating node, the ; user will be logged out. The LICENSETAG argument is used to enforce ; tx frequency limits. See [txlimits] below. 85 = cop,6 ; Remote base telephone key [telemetry] ; Telemetry entries can be shared across all repeaters, or defined for each repeater. ; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape sequence ; ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) ; Single frequencies are created by setting freq1 or freq2 to zero. ; ; |m - Morse escape sequence ; ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ; ; |i - Morse ID escape sequence ; ; Sends Morse code at the ID amplitude and ID frequency as defined in the ; [morse] section. ; ; path/to/sound/file/without/extension ; ; Send the sound if in place of a constructed tone. Do not include the file extension ; Example: ct8 = rpt/bloop ; Example: idrecording = rpt/nodenames/1999 ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2 = |t(660,880,150,2048) ct3 = |t(440,0,150,4096) ct4 = |t(550,0,150,2048) ct5 = |t(660,0,150,2048) ct6 = |t(880,0,150,2048) ct7 = |t(660,440,150,2048) ct8 = |t(700,1100,150,2048) ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0) remotemon = |t(1209,0,50,2048) ; local courtesy tone when receive only remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local courtesy tone when linked Trancieve mode cmdmode = |t(900,903,200,2048) functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048) pfxtone = |t(350,440,30000,3072) patchup = rpt/callproceeding patchdown = rpt/callterminated ; As far as what the numbers mean, ; (000,000,010,000) ; | | | |-------amplitude ; | | |-------------duration ; | |-------------------Tone 2 ; |-------------------------Tone 1 ; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude. ; Use it for a delay. Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter) ; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048. ; Morse code parameters, these are common to all repeaters. [morse] speed = 20 ; Approximate speed in WPM frequency = 800 ; Morse Telemetry Frequency amplitude = 4096 ; Morse Telemetry Amplitude idfrequency = 1065 ; Morse ID Frequency idamplitude = 1024 ; Morse ID Amplitude ; ; This section allows wait times for telemetry events to be adjusted ; A section for wait times can be defined for every repeater ; [wait-times] telemwait = 2000 ; Time to wait before sending most telemetry idwait = 500 ; Time to wait before starting ID unkeywait = 2000 ; Time to wait after unkey before sending CT's and link telemetry calltermwait = 2000 ; Time to wait before announcing "call terminated" ; ; This is where you define your nodes which cam be connected to. ; [nodes] ; Note, if you are using automatic update for allstar link nodes, ; no allstar link nodes should be defined here. Only place a definition ; for your local nodes, and private (off of allstar link) nodes here. 460310 = radio@....0.1:4569/460310,NONE ; This must be changed to your node number ; and iax port number if not the default ; Memories for remote bases [memory] ;00 = 146.580,100.0,m ;01 = 147.030,103.5,m+t ;02 = 147.240,103.5,m+t ;03 = 147.765,79.7,m-t ;04 = 146.460,100.0,m ;05 = 146.550,100.0,m ; Place command macros here [macro] ;1 = *32011# ;2 = *12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030# ;3 = *32001*32011*32050*32030*32060# ; Data Acquisition configuration ;[daq-list] ;device = device_name1 ;device = device_name2 ;Where: device_name1 and device_name2 are stanzas you define in this file ;device = daq-cham-1 ; Device name ;[daq-cham-1] ; Defined in [daq-list] ;hwtype = uchameleon ; DAQ hardware type ;devnode = /dev/ttyUSB0 ; DAQ device node (if required) ;1 = inadc ; Pin definition for an ADC channel ;2 = inadc ;3 = inadc ;4 = inadc ;5 = inadc ;6 = inadc ;7 = inadc ;8 = inadc ;9 = inp ; Pin definition for an input with a weak pullup resistor ;10 = inp ;11 = inp ;12 = inp ;13 = in ; Pin definition for an input without a weak pullup resistor ;14 = out ; Pin definition for an output ;15 = out ;16 = out ;17 = out ;18 = out ;[meter-faces] ;face = scale(scalepre,scalediv,scalepost),word/?,... ; ; scalepre = offset to add before dividing with scalediv ; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts). ; scalepost = offset to add after dividing with scalediv ; ;face = range(X-Y:word,X2-Y2:word,...),word/?,... ;face = bit(low-word,high-word),word/?,... ; ; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories, ; or a question mark which is a placeholder for the measured value. ; ; ; Battery voltage 0-20 volts ;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts ; 4 quadrant wind direction ;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,? ; LM34 temperature sensor with 130 deg. F full scale ;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit ; Status poll (non alarmed) ;light = bit(ha/off,ha/on),ha/light,? ;[alarms] ; ;tag = device,pin,node,ignorefirst,func-low,func-hi ; ;tag = a unique name for the alarm ;device = daq device to poll ;pin = the device pin to be monitored ;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it ;node = the node number to execute the function on ;func-low = the DTMF function to execute on a high to low transition ;func-high = the DTMF function to execute on a low to high transition ; ; a '-' as a function name is shorthand for no-operation ; ;door = daq-cham-1,9,1,2017,*7,- ;pwrfail = daq-cham-1,10,0,2017,*911111,- ; ; Control states ; Allow several control operator functions to be changed at once using one command (good for scheduling) ; ;[controlstates] ;statenum = copcmd,[copcmd]... ;0 = rptena,lnkena,apena,totena,ufena,noicd ; Normal operation ;1 = rptena,lnkena,apdis,totdis,ufena,noice ; Net and news operation ;2 = rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only operation ; Scheduler - execute a macro at a given time [schedule] ;dtmf_function = m h dom mon dow ; ala cron, star is implied ;2 = 00 00 * * * ; at midnight, execute macro 2. #includeifexists custom/rpt.conf Analog_Bridge.ini ; Analog_Bridge configuration file. ; This file should be placed in either /etc or it can be ; supplied as a path on the Analog_Bridge command line. ; The best way to think of this file is that there are two main sections, the USRP (analog audio) and ; AMBE_AUDIO (compressed audio). Analog_Bridge will take everything sent to the USRP port and ; encode it for transmission on the AMBE_AUDIO port. The encoder will use the format defined in ambeMode. ; As you might expect, the reverse direction is defined too. ; Analog_Bridge supports include files. More on this later... include = dvsm.macro ; include = asl.macro ; General Section describes settings for Analog_Bridge itself. [GENERAL] logLevel = 2 ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal ; Metadata management exportMetadata = true ; Export metadata to USRP partner (transcode setups require this) transferRootDir = /tmp ; Export database files to USRP partner subscriberFile = /var/lib/dvswitch/subscriber_ids.csv ; DMR ID to callsign lookup data ; General vocoder setup information decoderFallBack = true ; Allow software AMBE decoding if a hardware decoder is not found useEmulator = false ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN) emulatorAddress = 127.0.0.1:2470 ; IP address and port of the md380 server pcmPort = 2222 ; UDP port to send to the WebProxy ; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC) [AMBE_AUDIO] address = 127.0.0.1 ; IP address of xx_Bridge txPort = 31103 ; Transmit TLV frames to partner on this port rxPort = 31100 ; Listen for TLV frames from partner on this port ambeMode = DMR ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format) minTxTimeMS = 2500 ; Analog -> Digital Minimum time in MS for hang delay (0-10000) ; The metadata below is used when ASL is the source since it does not have any concept of digital modes gatewayDmrId = 1112721 ; ID to use when transmitting from Analog_Bridge 7 digit ID repeaterID = 111272123 ; ID of source repeater 7 digit ID plus 2 digit SSID txTg = 31676 ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge txTs = 2 ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge colorCode = 1 ; Color Code to assign DMR frames ; Information for USRP channel driver. This interface uses PCM to transfer audio information ; There are two typical configurations, ASL and Transcode. ASL (AllstarLink) is for analog clients connected ; to a digital network. Transcode is when Analog_Bridge actually points its PCM interfaces back at itself, ; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture. ; When using ASL, this matches the rpt.conf ASL file with a setting like: ; rxchannel = usrp/127.0.0.1:34001:32001 ; When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover). Launch ; each instance with its own ini file. [USRP] address = 127.0.0.1 ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge) txPort = 32001 ; Transmit USRP frames on this port rxPort = 34001 ; Listen for USRP frames on this port usrpAudio = AUDIO_UNITY ; Digital -> Analog (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_USE_AGC) usrpGain = 1.10 ; Gain factor when usrpAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY) usrpAGC = -20,10,100 ; Set the agc threshold (db), slope (db) and decay (ms) tlvAudio = AUDIO_UNITY ; Analog -> Digital (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF) tlvGain = 0.35 ; Gain factor when tlvAudio = AUDIO_USE_GAIN (0.0 to 5.0) (1.0 = AUDIO_UNITY) [MACROS] ; Where the macros are ; xxxx=yyyy ; xxxx is the dial string to match ; yyyy is the command line to execute ; xxxx must be preceded by a * ; xxxx can be any string (alphanumeric) ; yyyy is the command to execute ; yyyy will replace xxxx in the dial string ; arguments follow the macro name with a # delimiter ; For example using macro "5678" above would look like: ; *5678#9876 ; Which would invoke: ; echo 9876 ; Information for DV3000 hardware decoder ; There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware) ; Use top server and port if using AMBEServer ; Use bottom server/port and serial = true if using the DV3000u (thumbdv) ; Did you run AMBETest4.py before using this? [DV3000] address = 127.0.0.1 ; IP address of AMBEServer rxPort = 2460 ; Port of AMBEServer ; address = /dev/ttyUSB0 ; Device of DV3000U on this machine ; baud = 460800 ; Baud rate of the dongle (230400 or 460800) ; serial = true ; Use serial=true f
|
|
|
Steve N4IRS
I suggest you use these values:
duplex = 0 ; 0 = Half duplex with no telemetry
tones or hang time. Ah, but Allison STILL talks!
hangtime = 0 ; squelch tail hang time 0
althangtime = 0 ; longer squelch tail hang time 0
holdofftelem = 1 ; Hold off all telemetry when signal
is present on receiver or from connected nodes
; except when an ID needs to be done and there
is a signal coming from a connected node.
telemdefault = 0 ; 0 = telemetry output off. Don't send
Allison to DMR !!!!!!!!!!!!!!!!! Trust me.
telemdynamic = 0 ; 0 = disallow users to change the
local telemetry setting with a COP command,
linktolink = no ; disables forcing physical
half-duplex operation of main repeater while
; still keeping half-duplex semantics
(optional)
nounkeyct = 1 ; Set to a 1 to eliminate courtesy
tones and associated delays.
totime = 180000 ; transmit time-out time (in ms)
(optional, default 3 minutes 180000 ms)
; idrecording = |ie ; id recording or morse string see
http://ohnosec.org/drupal/node/87
; idtalkover = |ie ; Talkover ID (optional) default is
none see http://ohnosec.org/drupal/node/129
On 2/14/21 2:56 PM, Steve Siesel
[K4KSA] wrote:
It is now
working…Long hangtime I think I will change Hangtime to 20
Is chan_usrp
enabled in modules.conf?
On 2/14/21 2:50 PM, Steve Siesel [K4KSA]
wrote:
Yes…..
Did you fix
rpt.conf and did you then restart asterisk?
On 2/14/21 2:46 PM, Steve Siesel
[K4KSA] wrote:
After
restarting AB and Asterisk….also md3890-emu is running
Still no
Joy…Here is the latest start of Analog_bridge.log
I:
2021-02-14 19:43:13.761 Analog_Bridge is starting
M:
2021-02-14 19:43:13.762 Setting [MACROS] DMR ->
/opt/MMDVM_Bridge/dvswitch.sh mode DMR
M:
2021-02-14 19:43:13.762 Setting [MACROS] DSTAR ->
/opt/MMDVM_Bridge/dvswitch.sh mode DSTAR
M:
2021-02-14 19:43:13.762 Setting [MACROS] NXDN ->
/opt/MMDVM_Bridge/dvswitch.sh mode NXDN
M:
2021-02-14 19:43:13.762 Setting [MACROS] P25 ->
/opt/MMDVM_Bridge/dvswitch.sh mode P25
M:
2021-02-14 19:43:13.762 Setting [MACROS] YSF ->
/opt/MMDVM_Bridge/dvswitch.sh mode YSF
M:
2021-02-14 19:43:13.762 Setting [MACROS] dbupdate ->
/opt/MMDVM_Bridge/dvswitch.sh
collectProcessPushDataFiles
M:
2021-02-14 19:43:13.764 Setting [MACROS] 9876 ->
/opt/Analog_Bridge/parrot.sh
M:
2021-02-14 19:43:13.765 Setting [] include ->
dvsm.macro
M:
2021-02-14 19:43:13.766 Setting [GENERAL] logLevel ->
2
M:
2021-02-14 19:43:13.766 Setting [GENERAL] exportMetadata
-> true
M:
2021-02-14 19:43:13.767 Setting [GENERAL]
transferRootDir -> /tmp
M:
2021-02-14 19:43:13.767 Setting [GENERAL] subscriberFile
-> /var/lib/dvswitch/subscriber_ids.csv
M:
2021-02-14 19:43:13.768 Setting [GENERAL]
decoderFallBack -> true
M:
2021-02-14 19:43:13.768 Setting [GENERAL] useEmulator
-> false
M:
2021-02-14 19:43:13.769 Setting [GENERAL]
emulatorAddress -> 127.0.0.1:2470
M:
2021-02-14 19:43:13.769 Setting [GENERAL] pcmPort ->
2222
M:
2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] address
-> 127.0.0.1
M:
2021-02-14 19:43:13.769 Setting [AMBE_AUDIO] txPort
-> 31103
M:
2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] rxPort
-> 31100
M:
2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] ambeMode
-> DMR
M:
2021-02-14 19:43:13.770 Setting [AMBE_AUDIO] minTxTimeMS
-> 2500
M:
2021-02-14 19:43:13.771 Setting [AMBE_AUDIO]
gatewayDmrId -> 1112721
M:
2021-02-14 19:43:13.771 Setting [AMBE_AUDIO] repeaterID
-> 111272123
M:
2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTg ->
31676
M:
2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] txTs ->
2
M:
2021-02-14 19:43:13.772 Setting [AMBE_AUDIO] colorCode
-> 1
M:
2021-02-14 19:43:13.773 Setting [USRP] address ->
127.0.0.1
M:
2021-02-14 19:43:13.773 Setting [USRP] txPort ->
32001
M:
2021-02-14 19:43:13.773 Setting [USRP] rxPort ->
34001
M:
2021-02-14 19:43:13.774 Setting [USRP] usrpAudio ->
AUDIO_UNITY
M:
2021-02-14 19:43:13.774 Setting [USRP] usrpGain ->
1.10
M:
2021-02-14 19:43:13.774 Setting [USRP] usrpAGC ->
-20,10,100
M:
2021-02-14 19:43:13.775 Setting [USRP] tlvAudio ->
AUDIO_UNITY
M:
2021-02-14 19:43:13.775 Setting [USRP] tlvGain ->
0.35
M:
2021-02-14 19:43:13.776 Setting [DV3000] address ->
127.0.0.1
M:
2021-02-14 19:43:13.776 Setting [DV3000] rxPort ->
2460
I:
2021-02-14 19:43:13.777 Open UDP listener on
127.0.0.1:31100
I:
2021-02-14 19:43:13.777 Open USRP on 127.0.0.1:32001
M:
2021-02-14 19:43:13.777 Connecting to DV3000
hardware......
W:
2021-02-14 19:43:13.871 DV3000 did not reset at
127.0.0.1:2460
W:
2021-02-14 19:43:13.871 DV3000 not found at
127.0.0.1:2460 (Reset failed)
I:
2021-02-14 19:43:16.072 Subscriber IDs loaded: 187850
I:
2021-02-14 19:43:16.073 Default extended metadata
<K4KSA>
W:
2021-02-14 19:43:16.073 Using software MBE decoder
version 1.2.3
W:
2021-02-14 19:43:16.073 Using software OP25 IMBE/AMBE
vocoder
I:
2021-02-14 19:43:16.074 Sending to USRP clients at
127.0.0.1 on port(s) 32001
I:
2021-02-14 19:43:16.074 Sending PCM to clients at
127.0.0.1 on port 2222
I:
2021-02-14 19:43:16.074 Starting TLV -->
Analog_Bridge (decoder) --> USRP thread
I:
2021-02-14 19:43:16.075 Starting USRP -->
Analog_Bridge (encoder) -> TLV thread
You have 2
channel drivers uncommented:
rxchannel = dahdi/pseudo ; No radio (hub)
<--------------------- Comment this out.
; rxchannel = SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel = Pi/1 ; Raspberry Pi
PiTA
; rxchannel = Radio/usb_1999 ; USBRadio (DSP)
; rxchannel = Dahdi/1 ; PCI Quad card
; rxchannel = Beagle/1 ; BeagleBoard
rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio
interface USRP
; rxchannel = Voter/1999 ; RTCM device
On 2/14/21 2:34 PM, Steve Siesel
[K4KSA] wrote:
Can you look at this as well…..
I cannot get ASL<> AB to
talk….Here is my rpt.cof and Analog_bridge.ini. RF from
talkgroup 31676 make it in the logs of AB and MB. When
able to talk on Allstar via Corey’s WS, I see the
transmission in Allstar but nothing past that.
Steve
; Your
Repeater
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
[460310]
; Change this to your assigned node number
; Must also be enabled in modules.conf
; Rx audio/signalling channel. Choose ONLY 1 per node
stanza
; Enable the selected channel driver in modules.conf
!!!
rxchannel =
dahdi/pseudo ; No radio (hub)
; rxchannel =
SimpleUSB/usb_1999 ; SimpleUSB
; rxchannel =
Pi/1 ; Raspberry Pi PiTA
; rxchannel =
Radio/usb_1999 ; USBRadio (DSP)
; rxchannel =
Dahdi/1 ; PCI Quad card
; rxchannel =
Beagle/1 ; BeagleBoard
rxchannel =
USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel =
Voter/1999 ; RTCM device
duplex =
1 ; 0 = Half duplex with
no telemetry tones or hang time.
; Special Case: Full duplex if linktolink is set
to yes.
; This mode is preferred when interfacing with an
external multiport repeater controller.
; Comment out idrecording and idtalkover to
suppress IDs also
; 1 = Half duplex with telemetry tones and hang time.
Does not repeat audio.
; This mode is preferred when interfacing a
simplex node.
; 2 = Full Duplex with telemetry tones and hang time.
; This mode is preferred when interfacing a
repeater.
; 3 = Full Duplex with telemetry tones and hang time,
but no repeated audio.
; 4 = Full Duplex with telemetry tones and hang time.
Repeated audio only when the autopatch is down.
linktolink =
no ; disables forcing physical
half-duplex operation of main repeater while
; still keeping half-duplex semantics (optional)
linkmongain =
0 ; Link Monitor Gain adjusts
the audio level of monitored nodes when a signal from
another node or the local receiver is received.
; If linkmongain is set to a negative number the
monitored audio will decrease by the set amount in db.
; If linkmongain set to a positive number monitored
audio will increase by the set amount in db.
; The value of linkmongain is in db. The default value
is 0 db.
erxgain =
-3 ; Echolink receive gain
adjustment
; Note: Gain is in db-volts (20logVI/VO)
etxgain =
3 ; Echolink transmit gain
adjustment
; Note: Gain is in
db-volts (20logVI/VO)
;eannmode =
1 ; 1 = Say only node number
on echolink connects (default = 1)
; 2 = say phonetic call sign only on echolink connects
; 3 = say phonetic call sign
and node number on echolink connects
;controlstates
= controlstates ; system control state stanza
scheduler =
schedule ; scheduler stanza
functions =
functions ; Repeater Function stanza
phone_functions
= functions ; Phone Function stanza
link_functions
= functions ; Link Function stanza
telemetry =
telemetry ; Telemetry stanza
morse =
morse ; Morse stanza
wait_times =
wait-times ; Wait times stanza
context =
radio ; dialing context for
phone
callerid =
"Repeater" <0000000000> ; callerid for
phone calls
accountcode =
RADIO ; account code (optional)
hangtime =
5000 ; squelch tail hang time
(in ms) (optional, default 5 seconds, 5000 ms)
althangtime =
4000 ; longer squelch tail
totime =
180000 ; transmit time-out
time (in ms) (optional, default 3 minutes 180000 ms)
idrecording =
|iWA4XYZ ; cording or morse string
see http://ohnosec.org/drupal/node/87
idtalkover =
|iWA4XYZ ; Talkover ID (optional)
default is none see http://ohnosec.org/drupal/node/129
; See Telemetry section Example: idrecording =
rpt/nodenames/1999
idtime =
540000 ; id interval time (in
ms) (optional) Default 5 minutes (300000 ms)
politeid =
30000 ; time in milliseconds
before ID timer expires to try and ID in the tail.
(optional, default 30000)
unlinkedct =
ct2 ; Send a this courtesy tone
when the user unkeys if the node is not connected to
any other nodes. (optional, default is none)
remotect =
ct3 ; remote linked courtesy
tone (indicates a remote is in the list of links)
linkunkeyct =
ct8 ; sent when a transmission
received over the link unkeys
;nolocallinkct
= 0 ; Send unlinkedct instead if
another local node is connected to this node (hosted
on the same PC).
;connpgm =
yourconnectprogram ; Disabled. Execute a
program you specify on connect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being connected to us (them)
;discpgm =
yourdisconnectprogram ; Disabled. Execute a
program you specify on disconnect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being disconnected from us (them)
;lnkactenable
= 0 ; Set to 1 to enable the
link activity timer. Applicable to standard nodes
only.
;lnkacttime =
1800 ; Link activity timer time
in seconds.
;lnkactmacro
= *52 ; Function to execute when
link activity timer expires.
;lnkacttimerwarn
= 30seconds ; Message to play when the link
activity timer has 30 seconds left.
;remote_inact_timeout
= ; Specifies the amount of time
without keying from the link. Set to 0 to disable
timeout. (15 * 60)
;remote_timeout
= ; Session time out for remote
base. Set to 0 to disable. (60 * 60)
;remote_timeout_warning_freq
= ; 30
;remote_timeout_warning
= ; (3 * 60)
;nounkeyct =
0 ; Set to a 1 to eliminate
courtesy tones and associated delays.
holdofftelem
= 0 ; Hold off all telemetry
when signal is present on receiver or from connected
nodes
; except when an ID needs to be done and there is a
signal coming from a connected node.
telemdefault
= 0 ; 0 = telemetry output off
; 1 = telemetry output on (default
= 1)
; 2 = timed telemetry output on command execution and
for a short time thereafter.
telemdynamic
= 1 ; 0 = disallow users to
change the local telemetry setting with a COP command,
; 1 = Allow users to change the setting with a COP
command. (default = 1)
;beaconing =
0 ; Send ID regardless of
repeater activity (Required in the UK, but probably
illegal in the US)
parrotmode =
0 ; 0 = Parrot Off (default =
0)
; 1 = Parrot On Command
; 2 = Parrot Always
; 3 = Parrot Once by Command
parrottime =
1000 ; Set the amount of time in
milliseconds
; to wait before parroting what was received
;rxnotch=1065,40
; (Optional) Notch a particular frequency for a
specified
; b/w. app_rpt must have been compiled with
; the notch option
startup_macro
=
; nodenames =
/var/lib/asterisk/sounds/rpt/nodenames.callsign ;
Point to alternate nodename sound directory
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Need more
information on these
;extnodes =
extnodes-different ; section in extnodefile
containing dynamic node information (optional)
;extnodefile
= /foo/nodes ; Points to nodelist file
containing dynamic node info default =
/var/lib/asterisk/rpt_extnodes (optional)
;extnodefile2
= ; Is this a list of node files?
Possible a list of private nodes or a list of static
IPs for known nodes????
;nodenames =
/foo/names ; locaton of node sound files
default = /var/lib/asterisk/sounds/rpt/nodenames
;archivedir =
/tmp ; defines and enables activity
recording into specified directory (optional)
;monminblocks
= 2048 ; Min 1K blocks to be left on
partition (will not save monitor output if disk too
full)
;
; The tailmessagetime,tailsquashedtime, and
tailmessagelist need to be set
;
; to support tail messages. They can be omitted
otherwise.
;tailmessagetime
= 300000 ; Play a tail message every 5 mins
;tailsquashedtime
= 30000 ; If squashed by another user,
;
; try again after 30 seconds
;tailmessagelist
= msg1,msg2 ; list of messages to be played for
tail message
;
alt_functions
; ctgroup
;
dphone_functions
; idtime
; iobase
; iospeed
; locallist
;
mars Remote Base
; memory
; nobusyout
; nodes
;
nolocallinkct
; notelemtx
; outxlat
; parrot
;
propagate_phonedtmf
; rptnode
;
rptinactmacro Macro to execute when inactivity timer
expires
;
rptinacttime Inactivity timer time in seconds (0
seconds disables feature)
;
rxnotch Optional Audio notch
;
simplexphonedelay
; tonemacro
; tonezone
; txlimits
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; *** Status
Reporting ***
; Comment the
following statpost line stop to reporting of the
status of your node to stats.allstarlink.org
statpost_url
= http://stats.allstarlink.org/uhandler
; Status updates
[functions]
;
Prefix Functions
;
*1 Disconnect Link
;
*2 Monitor Link
;
*3 Connect Link
;
*4 Command Mode
;
*5 Macros
;
*6 User Functions
;
*7 Connection Status/Functions
;
*8 User Functions
;
*9 User Functions
;
*0 User Functions
;
*A User Functions
;
*B User Functions
;
*C User Functions
;
*D User Functions
; Mandatory
Command Codes
; http://docs.allstarlink.org/drupal/node/91
1 =
ilink,1 ; Disconnect specified link
2 =
ilink,2 ; Connect specified link --
monitor only
3 =
ilink,3 ; Connect specified link --
tranceive
4 =
ilink,4 ; Enter command mode on specified
link
70 =
ilink,5 ; System status
99 =
cop,6 ; PTT (phone mode only)
; End
Mandatory Command Codes
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Macro
Commands
5 = macro
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Autopatch
Commands
; Note, This
may be a good place for other 2 digit frequently used
commands
61 =
autopatchup,noct = 1,farenddisconnect = 1,dialtime =
20000 ; Autopatch up
62 =
autopatchdn
; Autopatch down
; autopatchup
can optionally take comma delimited setting=value
pairs:
; context =
string ; Override default context with
"string"
; dialtime =
ms ; Specify the max number of
milliseconds between phone number digits (1000
milliseconds = 1 second)
;
farenddisconnect = 1 ; Automatically
disconnect when called party hangs up
; noct =
1 ; Don't send repeater courtesy
tone during autopatch calls
; quiet =
1 ; Don't send dial tone, or
connect messages. Do not send patch down message when
called party hangs up
; Example:
123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Status
Commands
; 1 - Force
ID (global)
; 2 - Give
Time of Day (global)
; 3 - Give
software Version (global)
; 4 - Give
GPS location info
; 5 - Last
(dtmf) user
; 11 - Force
ID (local only)
; 12 - Give
Time of Day (local only)
721 =
status,1 ; Force ID (global)
722 =
status,2 ; Give Time of Day (global)
723 =
status,3 ; Give software Version (global)
724 =
status,4 ; Give GPS location info
725 =
status,5 ; Last (dtmf) user
711 =
status,11 ; Force ID (local only)
712 =
status,12 ; Give Time of Day (local only)
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Link
Commands
; 1 -
Disconnect specified link
; 2 - Connect
specified link -- monitor only
; 3 - Connect
specified link -- tranceive
; 4 - Enter
command mode on specified link
; 5 - System
status
; 6 -
Disconnect all links
; 7 - Last
Node to Key Up
; 8 - Connect
specified link -- local monitor only
; 9 - Send
Text Message (9,<destnodeno or 0 (for
all)>,Message Text, etc.
; 10 -
Disconnect all RANGER links (except permalinks)
; 11 -
Disconnect a previously permanently connected link
; 12 -
Permanently connect specified link -- monitor only
; 13 -
Permanently connect specified link -- tranceive
; 15 - Full
system status (all nodes)
; 16 -
Reconnect links disconnected with "disconnect all
links"
; 17 - MDC
test (for diag purposes)
; 18 -
Permanently Connect specified link -- local monitor
only
; ilink
commands 1 through 5 are defined in the Mandatory
Command section
806 =
ilink,6 ; Disconnect all links
807 =
ilink,7 ; Last Node to Key Up
808 =
ilink,8 ; Connect specified link --
local monitor only
809 =
ilink,9,1999,"Testing" ; would send a text message
to node 1999 replace 1999 with 0 for all connected
nodes
810 =
ilink,10 ; Disconnect all RANGER
links (except permalinks)
811 =
ilink,11 ; Disconnect a previously
permanently connected link
812 =
ilink,12 ; Permanently connect
specified link -- monitor only
813 =
ilink,13 ; Permanently connect
specified link -- tranceive
815 =
ilink,15 ; Full system status (all
nodes)
816 =
ilink,16 ; Reconnect links
disconnected with "disconnect all links"
817 =
ilink,17 ; MDC test (for diag
purposes)
818 = ilink
18 ; Permanently Connect specified
link -- local monitor only
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Control
operator (cop) functions. Change these to something
other than these codes listed below!
901 =
cop,1 �� ;
System warm boot
902 =
cop,2 ; System enable
903 =
cop,3 ; System disable
904 =
cop,4 ; Test tone on/off
(toggle)
905 =
cop,5 ; Dump system
variables on console (debug use only)
907 =
cop,7 ; Time out timer
enable
908 =
cop,8 ; Time out timer
disable
909 =
cop,9 ; Autopatch enable
910 =
cop,10 ; Autopatch disable
911 =
cop,11 ; User linking
functions enable
912 =
cop,12 ; User linking
functions disable
913 =
cop,13 ; Query system
control state
914 =
cop,14 ; Set system control
state
915 =
cop,15 ; Scheduler enable
916 =
cop,16 ; Scheduler disable
917 =
cop,17 ; User functions
enable (time, id, etc)
918 =
cop,18 ; User functions
disable
919 =
cop,19 ; Select alternate
hang time (althangtime)
920 =
cop,20 ; Select standard
hangtime (hangtime)
921 =
cop,21 ; Enable Parrot Mode
922 =
cop,22 ; Disable Parrot
Mode
923 =
cop,23 ; Birdbath (Current
Parrot Cleanup/Flush)
924 =
cop,24 ; Flush all
telemetry
925 =
cop,25 ; Query last node
un-keyed
926 =
cop,26 ; Query all nodes
keyed/unkeyed
927 =
cop,27 ; Reset DAQ minimum
on a pin
928 =
cop,28 ; Reset DAQ maximum
on a pin
930 =
cop,30 ; Recall Memory
Setting in Attached Xcvr
931 =
cop,31 ; Channel Selector
for Parallel Programmed Xcvr
932 =
cop,32 ; Touchtone pad
test: command + Digit string + # to playback all
digits pressed
933 =
cop,33 ; Local Telemetry
Output Enable
934 =
cop,34 ; Local Telemetry
Output Disable
935 =
cop,35 ; Local Telemetry
Output on Demand
936 =
cop,36 ; Foreign Link Local
Output Path Enable
937 =
cop,37 ; Foreign Link Local
Output Path Disable
938 =
cop,38 ; Foreign Link Local
Output Path Follows Local Telemetry
939 =
cop,39 ; Foreign Link Local
Output Path on Demand
942 =
cop,42 ; Echolink announce
node # only
943 =
cop,43 ; Echolink announce
node Callsign only
944 =
cop,44 ; Echolink announce
node # & Callsign
945 =
cop,45 ; Link Activity
timer enable
945 =
cop,46 ; Link Activity
timer disable
947 =
cop,47 ; Reset "Link Config
Changed" Flag
948 =
cop,48 ; Send Page Tone
(Tone specs separated by parenthesis)
949 =
cop,49 ; Disable incoming
connections (control state noice)
950 =
cop,50 ; Enable incoming
connections (control state noicd)
951 =
cop,51 ; Enable sleep mode
952 =
cop,52 ; Disable sleep mode
953 =
cop,53 ; Wake up from sleep
954 =
cop,54 ; Go to sleep
955 =
cop,55 ; Parrot Once if
parrot mode is disabled
956 =
cop,56 ; Rx CTCSS Enable
957 =
cop,57 ; Rx CTCSS Disable
958 =
cop.58 ; Tx CTCSS On Input
only Enable
959 =
cop,59 ; Tx CTCSS On Input
only Disable
960 =
cop,60 ; Send MDC-1200
Burst (cop,60,type,UnitID[,DestID,SubCode])
; Type is 'I' for PttID, 'E' for Emergency, and 'C'
for Call
; (SelCall or Alert), or 'SX' for STS (ststus), where
X is 0-F.
; DestID and subcode are only specified for the 'C'
type message.
; UnitID is the local systems UnitID. DestID is the
MDC1200 ID of
; the radio being called, and the subcodes are as
follows:
; Subcode '8205' is Voice Selective Call for Spectra
('Call')
; Subcode '8015' is Voice Selective Call for Maxtrac
('SC') or
; Astro-Saber('Call')
; Subcode '810D' is Call Alert (like Maxtrac 'CA')
961 =
cop,61 ; Send Message to
USB to control GPIO pins
(cop,61,GPIO1=0[,GPIO4=1].....)
962 =
cop,62 ; Send Message to
USB to control GPIO pins, quietly
(cop,62,GPIO1=0[,GPIO4=1].....)
963 =
cop,63 ; Send pre-configred
APRSTT notification (cop,63,CALL[,OVERLAYCHR])
964 =
cop,64 ; Send pre-configred
APRSTT notification, quietly
(cop,64,CALL[,OVERLAYCHR])
965 =
cop,65 ; Send POCSAG page
(equipped channel types only)
[functions-remote]
0 =
remote,1 ; Retrieve Memory
1 =
remote,2 ; Set freq.
2 =
remote,3 ; Set tx PL tone
3 =
remote,4 ; Set rx PL tone
40 =
remote,100 ; Rx PL off
41 =
remote,101 ; Rx PL on
42 =
remote,102 ; Tx PL off
43 =
remote,103 ; Tx PL on
44 =
remote,104 ; Low Power
45 =
remote,105 ; Medium Power
46 =
remote,106 ; High Power
711 =
remote,107 ; Bump -20
714 =
remote,108 ; Bump -100
717 =
remote,109 ; Bump -500
713 =
remote,110 ; Bump +20
716 =
remote,111 ; Bump +100
719 =
remote,112 ; Bump +500
721 =
remote,113 ; Scan - slow
724 =
remote,114 ; Scan - quick
727 =
remote,115 ; Scan - fast
723 =
remote,116 ; Scan + slow
726 =
remote,117 ; Scan + quick
729 =
remote,118 ; Scan + fast
79 =
remote,119 ; Tune
51 =
remote,5 ; Long status query
52 =
remote,140 ; Short status
query
67 =
remote,210 ; Send a *
69 =
remote,211 ; Send a #
;91 =
remote,99,CALLSIGN,LICENSETAG ; Remote base login.
; Define a different dtmf sequence for each user which
is
; authorized to use the remote base to control access
to it.
; For examble 9139583=remote,99,WB6NIL,G would grant
access to
; the remote base and announce WB6NIL as being logged
in.
; Another entry, 9148351=remote,99,WA6ZFT,E would
grant access to
; the remote base
and announce WA6ZFT as being logged in.
; When the remote base is disconnected from the
originating node, the
; user will be logged out. The LICENSETAG argument is
used to enforce
; tx frequency limits. See [txlimits] below.
85 =
cop,6 ; Remote base
telephone key
[telemetry]
; Telemetry
entries can be shared across all repeaters, or defined
for each repeater.
; Can be a
tone sequence, morse string, or a file
;
; |t - Tone
escape sequence
;
; Tone
sequences consist of 1 or more 4-tuple entries (freq1,
freq2, duration, amplitude)
; Single
frequencies are created by setting freq1 or freq2 to
zero.
;
; |m - Morse
escape sequence
;
; Sends Morse
code at the telemetry amplitude and telemetry
frequency as defined in the
; [morse]
section.
;
; Follow with
an alphanumeric string
;
; |i - Morse
ID escape sequence
;
; Sends Morse
code at the ID amplitude and ID frequency as defined
in the
; [morse]
section.
;
;
path/to/sound/file/without/extension
;
; Send the
sound if in place of a constructed tone. Do not
include the file extension
; Example:
ct8 = rpt/bloop
; Example:
idrecording = rpt/nodenames/1999
ct1 =
|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2 =
|t(660,880,150,2048)
ct3 =
|t(440,0,150,4096)
ct4 =
|t(550,0,150,2048)
ct5 =
|t(660,0,150,2048)
ct6 =
|t(880,0,150,2048)
ct7 =
|t(660,440,150,2048)
ct8 =
|t(700,1100,150,2048)
ranger =
|t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)
remotemon =
|t(1209,0,50,2048) ;
local courtesy tone when receive only
remotetx =
|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ;
local courtesy tone when linked Trancieve mode
cmdmode =
|t(900,903,200,2048)
functcomplete
= |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
remcomplete =
|t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)
pfxtone =
|t(350,440,30000,3072)
patchup =
rpt/callproceeding
patchdown =
rpt/callterminated
; As far as
what the numbers mean,
;
(000,000,010,000)
; | |
| |-------amplitude
; | |
|-------------duration
; |
|-------------------Tone 2
;
|-------------------------Tone 1
; So, with
0,0,10,0 That says No Tone1, No Tone2, 10ms duration,
0 Amplitude.
; Use it for
a delay. Fine tuning for how long before telemetry is
sent, in conjunction with the telemdelay parameter)
; The
numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms
delay, amplitude of 2048.
; Morse code
parameters, these are common to all repeaters.
[morse]
speed =
20 ; Approximate speed in
WPM
frequency =
800 ; Morse Telemetry
Frequency
amplitude =
4096 ; Morse Telemetry
Amplitude
idfrequency =
1065 ; Morse ID Frequency
idamplitude =
1024 ; Morse ID Amplitude
;
; This
section allows wait times for telemetry events to be
adjusted
; A section
for wait times can be defined for every repeater
;
[wait-times]
telemwait =
2000 ; Time to wait before
sending most telemetry
idwait =
500 ; Time to wait before
starting ID
unkeywait =
2000 ; Time to wait after unkey
before sending CT's and link telemetry
calltermwait
= 2000 ; Time to wait before
announcing "call terminated"
;
; This is
where you define your nodes which cam be connected to.
;
[nodes]
; Note, if
you are using automatic update for allstar link nodes,
; no allstar
link nodes should be defined here. Only place a
definition
; for your
local nodes, and private (off of allstar link) nodes
here.
460310 = radio@....0.1:4569/460310,NONE
; This must be changed to your node number
; and iax port number if not the default
; Memories
for remote bases
[memory]
;00 =
146.580,100.0,m
;01 =
147.030,103.5,m+t
;02 =
147.240,103.5,m+t
;03 =
147.765,79.7,m-t
;04 =
146.460,100.0,m
;05 =
146.550,100.0,m
; Place
command macros here
[macro]
;1 = *32011#
;2 =
*12001*12011*12043*12040*12050*12060*12009*12002*12003*12004*1113*12030#
;3 =
*32001*32011*32050*32030*32060#
; Data
Acquisition configuration
;[daq-list]
;device =
device_name1
;device =
device_name2
;Where:
device_name1 and device_name2 are stanzas you define
in this file
;device =
daq-cham-1
; Device name
;[daq-cham-1]
; Defined in [daq-list]
;hwtype =
uchameleon ; DAQ hardware type
;devnode =
/dev/ttyUSB0 ; DAQ device node (if
required)
;1 =
inadc ; Pin definition
for an ADC channel
;2 = inadc
;3 = inadc
;4 = inadc
;5 = inadc
;6 = inadc
;7 = inadc
;8 = inadc
;9 =
inp ; Pin definition
for an input with a weak pullup resistor
;10 = inp
;11 = inp
;12 = inp
;13 =
in ; Pin definition for
an input without a weak pullup resistor
;14 =
out ; Pin definition for
an output
;15 = out
;16 = out
;17 = out
;18 = out
;[meter-faces]
;face =
scale(scalepre,scalediv,scalepost),word/?,...
;
; scalepre =
offset to add before dividing with scalediv
; scalediv =
full scale/number of whole units (e.g. 256/20 or 12.8
for 20 volts).
; scalepost =
offset to add after dividing with scalediv
;
;face =
range(X-Y:word,X2-Y2:word,...),word/?,...
;face =
bit(low-word,high-word),word/?,...
;
; word/? is
either a word in /var/lib/asterisk/sounds or one of
its subdirectories,
; or a
question mark which is a placeholder for the measured
value.
;
;
; Battery
voltage 0-20 volts
;batvolts =
scale(0,12.8,0),rpt/thevoltageis,?,ha/volts
; 4 quadrant
wind direction
;winddir =
range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?
; LM34
temperature sensor with 130 deg. F full scale
;lm34f =
|
