Date
1 - 20 of 28
Setup of a Bridge YSF to DMR - Anyone out there who can solve this mystery ? #mmdvm_bridge
|
Uli
I simply want to link my YSF Reflector to a Talkgroup on Brandmeister.
Meanwhile I have tried 4 full installation attempts to do a Bridge between YSF and DMR but no luck. I have 2 RPI 3B+, both running raspbian stretch lite. One has a YSF Reflector installed according to QSO365´s (very good and working ) explanation. This Reflector and its Dashboard installed on the first attempt and runs fine without problems The other RPI 3B+ also has raspbian stretch lite installed, PHP7.0 and on top of it DVSwitch-System-Builder. Both RPi´s are running in the same Network 192.168.10.xxx behind a firewall. I was able to get the MMDVM_Bridge Dashboard running but it does not show any links or connection attempts from HT´s and the status is always idle. How do I get the MMDVM Bridge to link my reflector to the Brandmeister TG i have entered in DVSwitch.ini? Is there a complete detailed description which values in MMDVM_Bridge.ini and DVSwitch.ini and possibly in any other hidden config files or somewhere else need to be changed/adapted and how? I have done the suggested changes of values in the config files like from this https://dvswitch.groups.io/g/main/wiki/Bridge-DMR-to-YSF-Narrow but there are a lot of unanswered questions e.g. what do I put in "DMR adress" (I assume its the Brandmeister Master??) or in YSF Gateway Address (is it the URL of the other Pi that runs the Reflector?) What other ports do I need to open up on the firewall ? How should the config files look like for my setup? I have tried everything I could think of but no luck, the Bridge does not work as it should Do I need anything else (Software or Hardware than the two Raspberrys to do this? Did I miss anything? I´m completely stuck at this point. any help would greatly be appreciated Uli DJ5UW
|
|
|
|
Uli,
toggle quoted messageShow quoted text
Do not worry about the Dashboard. You want to look at the MMDVM_Bridge log file. If you setup MMDVM_Bridge.ini and DVSwitch.ini as the wiki states, all you should have to do is point MMDVM_Bridge at the 2 systems you want to bridge see below: [DMR Network] Enable=1 Address=hblink.dvswitch.org <---------- Point this at the DMR network Port=62031 Jitter=360 Local=62032 Password=passw0rd Slot1=0 Slot2=1 Debug=0 [System Fusion Network] Enable=1 LocalAddress=0 LocalPort=3200 GatewayAddress=ysfreflector.dvswitch.org <-------- point this at the YSF reflector GatewayPort=42166 <-------- Set this to the proper port for the reflector Debug=0 Steve, N4IRS
On 4/15/2020 4:17 AM, Uli wrote:
I simply want to link my YSF Reflector to a Talkgroup on Brandmeister.
|
|
|
|
Alec Wasserman
Yes double check ysf gateway port. Everything has to match and it will work !
|
|
|
|
Tito Lopez - YN1OB
I have a similar setup like you except mine nodes are in the cloud on two different VPS providers. I made those changes and I see traffic on TG hoseline at BM . I also see traffic in my YSF reflector the problem is that No YSF Audio is heard on either end. DVswitch Mobile on LTE and a hotspot at home. DMR mode on the hotspot is sweet except that YSFaudio cant be heard. YN1OB W3DAW
On Wed, Apr 15, 2020, 06:51 <alecwasserman@...> wrote: Yes double check ysf gateway port. Everything has to match and it will work !
|
|
|
|
Uli
Thanks everyone,
I have solved it now. The DVSwitch System Builder was the problem as it didn´t work. I have started from scratch again and only installed the Repo and DVSwitch Now Bridging to BM and back to YSF works fine, the sound is clear and noisefree. The Callsigns are also visble on both ends Uli DJ5UW
|
|
|
|
It would have been nice to know what was wrong. Based on what you
posted the config was correct. It would have been nice to see
traffic from both ends.
toggle quoted messageShow quoted text
Steve N4IRS
On 4/16/2020 11:26 AM, Uli wrote:
Thanks everyone,
|
|
|
|
Tito Lopez - YN1OB
Yep I did that just that rebuilt everything a few days ago, I still get no Audio from DMR <--->YSF Reflector. I see traffic but just that
|
|
|
|
I don't know about anyone else, but it's a little hard to
troubleshoot without seeing the logs.
toggle quoted messageShow quoted text
On 4/16/2020 12:56 PM, Tito Lopez
wrote:
Yep I did that just that rebuilt everything a few days ago, I still get no Audio from DMR <--->YSF Reflector. I see traffic but just that
|
|
|
|
Tito Lopez - YN1OB
Here is my Analog_Bridge Log
I: 2020-04-16 18:30:52.292 Analog_Bridge is starting
M: 2020-04-16 18:30:52.294 Setting [MACROS] DMR -> /opt/Analog_Bridge/dvswitch.sh mode DMR
M: 2020-04-16 18:30:52.294 Setting [MACROS] DSTAR -> /opt/Analog_Bridge/dvswitch.sh mode DSTAR
M: 2020-04-16 18:30:52.294 Setting [MACROS] NXDN -> /opt/Analog_Bridge/dvswitch.sh mode NXDN
M: 2020-04-16 18:30:52.294 Setting [MACROS] P25 -> /opt/Analog_Bridge/dvswitch.sh mode P25
M: 2020-04-16 18:30:52.294 Setting [MACROS] YSF -> /opt/Analog_Bridge/dvswitch.sh mode YSF
M: 2020-04-16 18:30:52.294 Setting [MACROS] dbupdate -> /opt/Analog_Bridge/dvswitch.sh collectProcessPushDataFiles
M: 2020-04-16 18:30:52.294 Setting [MACROS] 9876 -> /opt/Analog_Bridge/parrot.sh
M: 2020-04-16 18:30:52.294 Setting [] include -> dvsm.macro
M: 2020-04-16 18:30:52.294 Setting [GENERAL] logLevel -> 2
M: 2020-04-16 18:30:52.294 Setting [GENERAL] subscriberFile -> /var/lib/dvswitch/subscriber_ids.csv
M: 2020-04-16 18:30:52.294 Setting [GENERAL] exportMetadata -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] decoderFallBack -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] useEmulator -> true
M: 2020-04-16 18:30:52.294 Setting [GENERAL] emulatorAddress -> 127.0.0.1:2470
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txPort -> 31103
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] rxPort -> 31100
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] ambeMode -> DMR
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] minTxTimeMS -> 2500
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] gatewayDmrId -> 7101003
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] repeaterID -> 710100306
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txTg -> 710411
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] txTs -> 2
M: 2020-04-16 18:30:52.294 Setting [AMBE_AUDIO] colorCode -> 1
M: 2020-04-16 18:30:52.294 Setting [USRP] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [USRP] txPort -> 32001
M: 2020-04-16 18:30:52.294 Setting [USRP] rxPort -> 34001
M: 2020-04-16 18:30:52.294 Setting [USRP] usrpAudio -> AUDIO_USE_GAIN
M: 2020-04-16 18:30:52.294 Setting [USRP] usrpGain -> .8
M: 2020-04-16 18:30:52.294 Setting [USRP] tlvAudio -> AUDIO_USE_GAIN
M: 2020-04-16 18:30:52.294 Setting [USRP] tlvGain -> 0.25
M: 2020-04-16 18:30:52.294 Setting [DV3000] address -> 127.0.0.1
M: 2020-04-16 18:30:52.294 Setting [DV3000] rxPort -> 2460
I: 2020-04-16 18:30:52.294 Open UDP listener on 127.0.0.1:31100
I: 2020-04-16 18:30:52.294 Open USRP on 127.0.0.1:32001
M: 2020-04-16 18:30:52.294 Connecting to DV3000 hardware......
W: 2020-04-16 18:30:53.325 DV3000 not found at 127.0.0.1:2460
I: 2020-04-16 18:30:53.326 Subscriber IDs loaded: 0
I: 2020-04-16 18:30:53.326 Default extended metadata <7101003>
I: 2020-04-16 18:30:53.326 Connecting to emulator on host 127.0.0.1:2470
W: 2020-04-16 18:30:53.326 Using software MBE decoder version 1.2.3
W: 2020-04-16 18:30:53.326 Using software OP25 IMBE/AMBE vocoder
I: 2020-04-16 18:30:53.326 Connected to USRP 127.0.0.1:32001
I: 2020-04-16 18:30:53.326 Starting TLV --> Analog_Bridge (decoder) --> USRP thread
I: 2020-04-16 18:30:53.327 Starting USRP --> Analog_Bridge (encoder) -> TLV thread
==================================================================================== MMDVM_Bridge Log I: 2020-04-16 18:30:52.278 Portions Copyright (C) 2018 DVSwitch, INAD.
I: 2020-04-16 18:30:52.278 Hacks by Mike N4IRR and Steve N4IRS
I: 2020-04-16 18:30:52.278 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
I: 2020-04-16 18:30:52.278 This software is for use on amateur radio networks only,
I: 2020-04-16 18:30:52.278 it is to be used for educational purposes only. Its use on
I: 2020-04-16 18:30:52.278 commercial networks is strictly prohibited.
I: 2020-04-16 18:30:52.278 Copyright(C) 2015-2018 by Jonathan Naylor, G4KLX and others
M: 2020-04-16 18:30:52.278 MMDVM_Bridge-20191105_V1.4.1 is starting
M: 2020-04-16 18:30:52.278 Built 14:23:56 Nov 11 2019 (GitID #9dae1ac)
I: 2020-04-16 18:30:52.278 General Parameters
I: 2020-04-16 18:30:52.278 Callsign: YN1OB
I: 2020-04-16 18:30:52.278 Id: 710100306
I: 2020-04-16 18:30:52.278 Duplex: no
I: 2020-04-16 18:30:52.278 Timeout: 180s
I: 2020-04-16 18:30:52.278 D-Star: disabled
I: 2020-04-16 18:30:52.278 DMR: enabled
I: 2020-04-16 18:30:52.278 YSF: enabled
I: 2020-04-16 18:30:52.278 P25: disabled
I: 2020-04-16 18:30:52.278 NXDN: disabled
I: 2020-04-16 18:30:52.278 Modem Parameters
I: 2020-04-16 18:30:52.278 Port: /dev/null
I: 2020-04-16 18:30:52.278 RX Invert: no
I: 2020-04-16 18:30:52.278 TX Invert: no
I: 2020-04-16 18:30:52.278 PTT Invert: no
I: 2020-04-16 18:30:52.278 TX Delay: 100ms
I: 2020-04-16 18:30:52.278 RX Offset: 0Hz
I: 2020-04-16 18:30:52.278 TX Offset: 0Hz
I: 2020-04-16 18:30:52.278 RX DC Offset: 0
I: 2020-04-16 18:30:52.278 TX DC Offset: 0
I: 2020-04-16 18:30:52.278 RF Level: 100.0%
I: 2020-04-16 18:30:52.278 DMR Delay: 0 (0.0ms)
I: 2020-04-16 18:30:52.278 RX Level: 50.0%
I: 2020-04-16 18:30:52.278 CW Id TX Level: 50.0%
I: 2020-04-16 18:30:52.278 D-Star TX Level: 50.0%
I: 2020-04-16 18:30:52.278 DMR TX Level: 50.0%
I: 2020-04-16 18:30:52.278 YSF TX Level: 50.0%
I: 2020-04-16 18:30:52.278 P25 TX Level: 50.0%
I: 2020-04-16 18:30:52.278 NXDN TX Level: 50.0%
I: 2020-04-16 18:30:52.278 RX Frequency: 222340000Hz (222340000Hz)
I: 2020-04-16 18:30:52.278 TX Frequency: 224940000Hz (224940000Hz)
M: 2020-04-16 18:30:52.279 Opening the MMDVM
I: 2020-04-16 18:30:52.279 Display Parameters
I: 2020-04-16 18:30:52.279 Type:
I: 2020-04-16 18:30:52.279 DMR Network Parameters
I: 2020-04-16 18:30:52.279 Address: 74.91.118.251 ;3103.repeater.net
I: 2020-04-16 18:30:52.279 Port: 62031
I: 2020-04-16 18:30:52.279 Local: 62032
I: 2020-04-16 18:30:52.279 Jitter: 360ms
I: 2020-04-16 18:30:52.279 Slot 1: disabled
I: 2020-04-16 18:30:52.279 Slot 2: enabled
I: 2020-04-16 18:30:52.279 Mode Hang: 3s
I: 2020-04-16 18:30:52.279 Info Parameters
I: 2020-04-16 18:30:52.279 Callsign: YN1OB
I: 2020-04-16 18:30:52.279 RX Frequency: 222340000Hz
I: 2020-04-16 18:30:52.279 TX Frequency: 224940000Hz
I: 2020-04-16 18:30:52.279 Power: 1W
I: 2020-04-16 18:30:52.279 Latitude: 41.733299deg N
I: 2020-04-16 18:30:52.279 Longitude: -50.399899deg E
I: 2020-04-16 18:30:52.279 Height: 0m
I: 2020-04-16 18:30:52.279 Location: "Iceberg, North Atlantic"
I: 2020-04-16 18:30:52.279 Description: "MMDVM_Bridge"
I: 2020-04-16 18:30:52.279 URL: "https://groups.io/g/DVSwitch"
M: 2020-04-16 18:30:52.279 DMR, Opening DMR Network
I: 2020-04-16 18:30:52.279 System Fusion Network Parameters
I: 2020-04-16 18:30:52.279 Local Address: 0
I: 2020-04-16 18:30:52.279 Local Port: 3200
I: 2020-04-16 18:30:52.279 Gateway Address: 149.248.2.133
I: 2020-04-16 18:30:52.279 Gateway Port: 42000
I: 2020-04-16 18:30:52.279 Mode Hang: 3s
M: 2020-04-16 18:30:52.279 Opening YSF network connection
I: 2020-04-16 18:30:52.279 RSSI
I: 2020-04-16 18:30:52.279 Mapping File: RSSI.dat
W: 2020-04-16 18:30:52.279 Cannot open the RSSI data file - RSSI.dat
I: 2020-04-16 18:30:52.280 DMR Id Lookups
I: 2020-04-16 18:30:52.280 File: /var/lib/mmdvm/DMRIds.dat
I: 2020-04-16 18:30:52.280 Reload: 24 hours
I: 2020-04-16 18:30:52.589 Loaded 161717 Ids to the DMR callsign lookup table
I: 2020-04-16 18:30:52.589 DMR RF Parameters
I: 2020-04-16 18:30:52.589 Id: 710100306
I: 2020-04-16 18:30:52.589 Color Code: 1
I: 2020-04-16 18:30:52.589 Self Only: no
I: 2020-04-16 18:30:52.589 Embedded LC Only: yes
I: 2020-04-16 18:30:52.589 Dump Talker Alias Data: no
I: 2020-04-16 18:30:52.589 Prefixes: 0
I: 2020-04-16 18:30:52.589 Call Hang: 3s
I: 2020-04-16 18:30:52.589 TX Hang: 3s
I: 2020-04-16 18:30:52.589 Mode Hang: 10s
M: 2020-04-16 18:30:52.589 DMR, Opening INI file: DVSwitch.ini
I: 2020-04-16 18:30:52.589 Started the DMR Id lookup reload thread
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] Address -> 127.0.0.1
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] TXPort -> 31100
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] RXPort -> 31103
M: 2020-04-16 18:30:52.590 DMR, Setting [DMR] Slot -> 2
M: 2020-04-16 18:30:52.590 DMR, Transmitting on 127.0.0.1:31100 and listening on port 31103. Result = 1
I: 2020-04-16 18:30:52.590 YSF RF Parameters
I: 2020-04-16 18:30:52.590 Low Deviation: no
I: 2020-04-16 18:30:52.590 Remote Gateway: no
I: 2020-04-16 18:30:52.590 Self Only: no
I: 2020-04-16 18:30:52.590 DSQ: no
I: 2020-04-16 18:30:52.590 Mode Hang: 10s
M: 2020-04-16 18:30:52.590 YSF, Opening INI file: DVSwitch.ini
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] Address -> 127.0.0.1
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] TXPort -> 31103
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] RXPort -> 31100
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] FallbackID -> 3128973
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] ExportTG -> 710411
M: 2020-04-16 18:30:52.590 YSF, Setting [YSF] Slot -> 2
M: 2020-04-16 18:30:52.590 YSF, Transmitting on 127.0.0.1:31103 and listening on port 31100. Result = 1
M: 2020-04-16 18:30:52.590 MMDVM_Bridge-20191105_V1.4.1 is running
M: 2020-04-16 18:31:02.635 DMR, Logged into the master successfully
|
|
|
|
Analog_Bridge is not used in a DMR to YSFn bridge.
toggle quoted messageShow quoted text
On 4/16/2020 2:38 PM, Tito Lopez wrote:
Here is my Analog_Bridge Log
|
|
|
|
Tito Lopez - YN1OB
So what is it that you need?
On Thu, Apr 16, 2020 at 12:52 PM Steve N4IRS <szingman@...> wrote:
|
|
|
|
What program are you running to build the bridge? I need that log
with traffic in both directions.
toggle quoted messageShow quoted text
<https://dvswitch.groups.io/g/main/wiki/Bridge-DMR-to-YSF-Narrow> <https://dvswitch.groups.io/g/main/wiki/Help%21>
On 4/16/20 5:44 PM, Tito Lopez wrote:
|
|
|
|
Uli
@Tito: Did you open up all necessary ports on your router? That was one of my problems in the first place that prevented the connection
Try to run something like tail -f /var/log/mmdvm/MMDVM_Bridge-2020-04-17.log (replace the date with the current date) to display a live log and check what is going on Now take a DMR HT and a C4fm HT key up and check whats shown in the livelog @Steve: I have no clue why the DVSwitch system builder did not work. It might have been a user rights problem or it did not like the raspbian stretch lite, but I don´t know for sure. When I have time, I´ll give it another try. Uli
|
|
|
|
Uli
@Tito: I have put your YSF Reflector IP into my MMDVM_Bridge.ini file rebooted and did a few tests. It works fine, I get audio in both directions.
Did you open up in your router port 42000 UDP pointing to the IP of your RPI with the MMDVM_Bridge running on it? Uli
|
|
|
|
Tito Lopez - YN1OB
Ah so you are the one that is connected to the reflector. Cool. So it works fine. The problem is on my end.
On Fri, Apr 17, 2020 at 10:11 AM Uli <g90@...> wrote: @Tito: I have put your YSF Reflector IP into my MMDVM_Bridge.ini file rebooted and did a few tests. It works fine, I get audio in both directions.
|
|
|
|
Uli
Yes that was me yesterday on your Reflector testing.
Can you post you MMDVM_Bridge.ini and your DVSwitch.ini so that I can compare it to mine? Maybe that gives a hint where the problem lies. Uli
|
|
|
|
Aaron Groover
This is where i get stuck. How does it communicate without Analog_Bridge.ini?
|
|
|
|
Because it's all digital. No need for a Analog component.
toggle quoted messageShow quoted text
On 11/16/2020 8:43 AM, Aaron Groover
wrote:
This is where i get stuck. How does it communicate without Analog_Bridge.ini?
|
|
|
|
KC1JFN
Hi, I have the same set up with Uli, both RPI running on raspbian stretch lite on the same network. I did what Steve told Uli to do by pointing MMDVM_Bridge at the 2 systems you want to bridge. But it does not work. I am a newbie with regards to this things.
Is it only on MMDVm_Bridge.ini that I have to change? What does it mean by GatewayAddress=ysfreflector.dvswitch.org <-------- point this at the YSF reflector? The ip address to the YSF Reflector is, My public ip? I downloaded this from YSF Reflector registry 07854;US-ICARE-Iloilo;ICARE Iloilo;32.214.141.124;42002;001;http://ic6008.com/Dashboard This is what I put in GatewayAddress=32.214.141.124 GatewayPort=42002 Please help, Thank you
|
|
|
|
KC1JFN
I did some experiment, since the bridge and the YSF reflector are on the same LAN. I change the GatewayAddress=to the local ip address of the YSF Reflector server, which is also on the same network with the YSF to DMR Bridge.
KC1JFN
|
|
|