Your gatewayDmrId nnnnnnn is NOT in the subscriber f .net ile.
The following message is showing in AB.
Could someone tell me what this means, and how to fix it.
"Your gatewayDmrId nnnnnnn is NOT in the subscriber f .net
ile. Please correct this."
Please post your AB.ini file.toggle quoted messageShow quoted text
On 12/1/20 5:21 AM, G4WXN@... wrote:
Here it is
; Analog_Bridge configuration file.
; This file should be placed in either /etc or it can be
; supplied as a path on the Analog_Bridge command line.
; The best way to think of this file is that there are two main sections, the USRP (analog audio) and
; AMBE_AUDIO (compressed audio). Analog_Bridge will take everything sent to the USRP port and
; encode it for transmission on the AMBE_AUDIO port. The encoder will use the format defined in ambeMode.
; As you might expect, the reverse direction is defined too.
; Analog_Bridge supports include files. More on this later...
include = dvsm.macro
include = asl.macro
; General Section describes settings for Analog_Bridge itself.
logLevel = 2 ; Show messages and above 0=No logging, 1=Debug, 2=Message, 3=Info, 4=Warning, 5=Error, 6=Fatal
; Metadata management
subscriberFile = /var/lib/dvswitch/subscriber_ids.csv ; DMR ID to callsign lookup data
exportMetadata = true ; Export metadata to USRP partner (transcode setups require this)
transferRootDir = /tmp ; Export database files to USRP partner
; General vocoder setup information
decoderFallBack = false ; Allow software AMBE decoding if a hardware decoder is not found
useEmulator = false ; Use the MD380 AMBE emulator for AMBE72 (DMR/YSFN/NXDN)
emulatorAddress = 127.0.0.1:2470 ; IP address and port of the md380 server
; Information for xx_Bridge (Where xx is MMDVM, Quantar, HB, IPSC)
address = 127.0.0.1 ; IP address of xx_Bridge
txPort = 42025 ; 31103 Transmit TLV frames to partner on this port
rxPort = 41025 ; 31100 Listen for TLV frames from partner on this port
ambeMode = DMR ; DMR, DMR_IPSC, DSTAR, NXDN, P25, YSFN, YSFW (encode PCM to this format)
minTxTimeMS = 2500 ; Minimum time in MS for hang delay (0-10000)
; The metadata below is used when ASL is the source since it does not have any concept of digital modes
gatewayDmrId =2352421 ; ID to use when transmitting from Analog_Bridge
repeaterID =235242102 ; ID of source repeater
txTg = 9 ; TG to use for all frames sent from Analog_Bridge -> xx_Bridge
txTs = 2 ; Slot to use for frames sent from Analog_Bridge -> xx_Bridge
colorCode = 1 ; Color Code to assign DMR frames
; Information for USRP channel driver. This interface uses PCM to transfer audio information
; There are two typical configurations, ASL and Transcode. ASL (AllstarLink) is for analog clients connected
; to a digital network. Transcode is when Analog_Bridge actually points its PCM interfaces back at itself,
; causing a TLV <-- (pcm <--> pcm) --> TLV type of architecture.
; When using ASL, this matches the rpt.conf ASL file with a setting like:
; rxchannel = usrp/127.0.0.1:34001:32001
; When Transcoding, make two ini files and set txPort equal to the other instance rxPort (crossover). Launch
; each instance with its own ini file.
address = 169.254.42.42 ; IP address of USRP partner (Allstar/Asterisk or another Analog_Bridge)
txPort = 46001 ; Transmit USRP frames on this port
rxPort = 46001 ; Listen for USRP frames on this port
usrpAudio = AUDIO_UNITY ; Audio to ASL (AUDIO_UNITY, AUDIO_USE_AGC, AUDIO_USE_GAIN)
usrpGain = 6 ; Gain (in db) of the AGC filter
usrpAgc = -20,10,100 ; Set the agc threshold (db), slope (db) and decay (ms)
tlvAudio = AUDIO_UNITY ; Audio from ASL (AUDIO_UNITY, AUDIO_USE_GAIN, AUDIO_BPF)
tlvGain = 0.35 ; Gain factor of audio from ASL (0.0-1.0)
; Where the macros are
; xxxx is the dial string to match
; yyyy is the command line to execute
; xxxx must be preceded by a *
; xxxx can be any string (alphanumeric)
; yyyy is the command to execute
; yyyy will replace xxxx in the dial string
; arguments follow the macro name with a # delimiter
; For example using macro "5678" above would look like:
; Which would invoke:
; echo 9876
; Information for DV3000 hardware decoder
; There are two configuration modes: IP (AMBEServer) and serial (direct connect hardware)
; Use top server and port if using AMBEServer
; Use bottom server/port and serial = true if using the DV3000u (thumbdv)
; Did you run AMBETest4.py before using this?
;address = 127.0.0.1 ; IP address of AMBEServer
;rxPort = 2471 ; Port of AMBEServer
address = /dev/ttyUSB0 ; Device of DV3000U on this machine
baud = 460800 ; Baud rate of the dongle (230400 or 460800)
serial = true ; Use serial=true for direct connect or serial=false for AMBEServer
OK,toggle quoted messageShow quoted text
The message means that Analog_Bridge can not find your ID in it's database.
From the command line as root (sudo -s) do this:
/opt/MMDVM_Bridge/dvswitch.sh lookup 2352421
Does it return your ID callsign and name?
grep 2352421 /var/lib/dvswitch/subscriber_ids.csv
Does it return your ID, callsign, and name?
If either one is no
systemctl trestart analog_bridge
Check the log for the error.
On 12/1/2020 8:37 AM, G4WXN@... wrote:
all seems ok now.
Good to hear.toggle quoted messageShow quoted text
On 12/1/2020 9:19 AM, G4WXN@... wrote:
For reasons I cannot fathom, this error keeps cropping up.
Running the update fixes the problem, but then it comes back again.
This problem continues to occur randomly.
Just had to run the update again.
Any help appreciated.