I have a Private Node (set up exactly as the Example Node) for a YSF Reflector ASL<->AB<->MB<->YSF. AB and MB exist in a Cloud Server. I can transmit through my ASL Node to the YSF Reflector with out

I want to add DVSwitch Server to my system. Currently I have ASL along with Analog Bridge and MMDVM Bridge in one Raspberry Pi. Can I add DV Switch Server in here as well? Once installed would DVSwitc

What instructions did you follow?

I want to connect to the Ysf side of the YCS Server. Works ok If I connect to the Fcs side At the moment I have. Ysfreflector to MB to MB to Ysfgateway to YCS (Ysf DG-ID 35) Traffic passes from the Yc

I have DVswitch setup DMR>Analog. It pushes a DMR TG to my Hamvoip Allstar node (2 seperate Pi's). When I talk on the analog radio, the audio sounds great coming out of my DMR radio connected to a Ope

Installed DVSwitch on a debian 9 amazon AWS, used the dvswitch builder for the install. No joy on the dashboard...I've opened port 80 on the instance... 403 forbidden when I enter the public IP addres

Hi, I have noticed that when restarting services via the "dvs" menu “Restart DVSwitch Services” or using the “Drop Dynamic TGs” in the DVSM App, the DMR server always returns to a particular server. W

My MMDVM_Bridge.ini has the following [Info] RXFrequency=444775000 TXFrequency=449775000 Power=200 Latitude=40.789737 Longitude=-76.121412 Height=550 Location=Barnesville, PA Description=W3TWA MMDVM_B

I finally got the DVswitch up and running. The Analog to dmr link is working fine. The only issue I have, is every 10 minutes, this ID is played ONLY on the DMR TG (Not the analog side) Anyone know wh

I set up a Raspberry Pi last week with Hamvoip. The Allstar Node is up and running and RF is connected. It has a private node 1999 also. I installed DVSwitch on the second Pi (No ALS) I followed the D

These are my ini files for a Brandmeister TG to XLX bridge BM TG <> MMDVM_Bridge <> MMDVM_Bridge <> XLX (DMR Mode) Had one way audio for a while and was tearing my hair out.. (now have none left :-) )

Hi Steve, we have installed a public DVswitch server pool. Is it possible APP or hUC USRB client (feature, time later) switch automaticly to the next server entry if selected fails, not reachable, or

Hello all, following many tutorials and hows to, and studying and again studying I succesfully manage to install hblink on a amhf rockchip processor board. It starts and also dashboard is working fine

Hey guys I wanted to add macros in the config section of dvswitch to shut down or restart my allstar node but when i close the app and restart the app it resets the macros I entered I believe I have t

Hello gentlemen of DVswitch. I have already experienced a few times that when I have too little 4G (Mobile data) signal, DV switch crashes. The PTT key turns red, and then transmits continuously. I ha

Hi All - I have some confusions and questions regarding DVSwitch and the App. I have DVSwitch up and running, but there's some things I can't seem to figure out and can't find a doc to explain it to m

I currently have a test system where I have bridged YSF and DMR using MMDVM_Bridge. I have the P25Reflector installed on the same system running as a standalone reflector. I would like to add P25 to t

Please excuse my stupidity, I am struggling to get my head around a problem I have. I have DVS running on a Rpi, in MMDVM_Bridge.ini I have the following settings -------------------------- Address=hb

I have separate MB ini files for each DMR network these are copied over the MB ini file and then MB service restarts. Which brings me to a question. When using these customised MB ini files, is it bes

Just an enquiry on a minor issue. I use DVSwitch Mobile on an Android device with no keyboard and a quite small screen. I am unable to enter Talkgroup numbers or commands as the on screen keyboard is